SiXPIR Installation Guide

SiXTM Series

SiXPIR

Installation Instructions

This wireless passive infrared motion sensor is intended for use with Honeywell controls that support SiX™ series
devices.
Satisfactory

Mounting Location

No

• The optimal range is
obtained at a mounting
height of 7’ 6” (2.3 m).
• Allow a clear line-of-sight to
all areas to protect.

7' - 9'
(2.1 - 2.7 m)
7' 6"
(2.3 m) Optimal

• Do not directly face
windows.
• Avoid close proximity to
moving machinery,
fluorescent lights, and
heating/cooling sources.

> 6' (1.8 m)

≤ 80 lbs
36 kg

• For use in applications with
pets up to 80 pounds (36
kilograms).
In Applications with Animals:

•
•
•

Mounting Options
NOTE: before mounting the
device permanently, conduct
Go/No Go tests (see
controller’s instructions) to
verify adequate signal strength
and adjust the device location
and orientation as necessary.
The SIXPIR can be mounted
on the wall or in corners:
• [A] = Wall mounting holes.
• [B] = Corner mounting
holes.
• The rear tamper plate
MUST be mounted to a
stud, solid wood, or with a
robust wall anchor.

A

Mount with the center of the device at 7.5 feet (2.3m)
Mount where pet cannot come within 6 feet (1.8m) of the sensor by climbing on furniture,
stairs, boxes or other objects.
Test each installation to determine exact level of animal immunity; levels vary based on
environmental differences and the amount of heat radiated by an animal.

#4 x 1"
(2.9 mm x 25 mm)

B

B
A

B
X

X

#4 x 1"
(2.9 mm x 25 mm)

B

B
A

Press down on the top latch and separate the front
and back covers.
1. Set the Lyric Controller in Programming Mode
and go to Zone Programming. Select Add New,
then Serial Number.
2. Remove the battery tab to activate and begin
the enrollment process.
3. The green LED beneath the battery flashes
during enrollment.*
- The device sends its unique MAC ID (Serial
Number) and Services information to the
controller.
- The controller registers the device and
displays the transmitter data on screen.

Serial Number

Loop Number

Zone Description 1

Zone Description 2

Device Type

Response Type

Alarm Report

Chime

Supervision

Panic

The LED
Flashes
for up to
about 20
seconds

Home

2

3
0
10
45
20
30

4
LED is
ON for
3 seconds

*NOTE: Enrollment time varies depending on the
signal strength between the device and the controller
and may take up to about 20 seconds.

4. Enrollment is confirmed when the LED is ON for
3 seconds and the controller beeps.
5. Trigger the device tamper switch again to
complete enrollment.
6. Press SAVE.
If the sensor is not successfully enrolled during the
enrollment period, the LED turns off and the device
enters a sleep mode. Activate a tamper or remove
and reinsert the battery to restart the enrollment
process.
The device can also be manually enrolled. See the
Controller’s Programming Guide for details.

Programming Mode > Zones >
Add New > Serial Number

PUL
L
CON TO
NEC
T

1

The SIXPIR can be enrolled and programmed
before or after installation.

PUL
L
CON TO
NEC
T

Enroll the SIXPIR

5
Trigger the
device again
to complete
enrollment

6 Press SAVE

NOTE: Once enrolled in a system, the sensor cannot be used with
another controller until it is removed from the current controller. See
the Controller’s instructions for details.

Follow instructions in the Controller’s programming guide to
program the sensor in the system.

After enrolling, update the SiXPIR firmware (via
the Controller) to ensure the latest version is used.
See the Controller’s instructions.

Pet Immunity is selectable: Off or Up to 80 lbs (36 kg).

Walk Test the SIXPIR

Activate the Test Mode
from the
controller
OR
< 4’ (1.2m)
using the
Flashlight
1/2 sec.
Feature hold 3-5x

After power up and enrollment, activate the Test
Mode with the controller (see controller’s
instructions) or use the Flashlight Feature.
NOTE: the system must be in disarmed mode for the 10
minute Test mode to begin.

Walk through the detection area and observe the
LED.

Serial Number

Loop Number

Zone Description 1

Zone Description 2

Device Type

Response Type

Alarm Report

Panic

Chime

Supervision

Home

Test Mode is active for 10 minutes, then
automatically exits test mode, disables the LED
and enters normal operation mode.
To restart the 10 minute Test Mode, use the
flashlight feature (see the following section).

10 minutes

Flashlight Feature
The flashlight feature is only available for the first 24 hours after the
first power up, or until the system is first armed. This feature is no
longer available after the first system arming.

< 4’ (1.2m)

Each time the flashlight features is used, and the system is disarmed,
the walk test timer restarts for 10 minutes.

1/2 sec.
hold 3-5x

1. Use a flashlight with a bright light beam, and stand within 4’ (1.2 m)
of the sensor.
2. Swing the light beam past the sensor Lens 3-5 times, holding the
beam on the window for 0.5 second each pass.

Detection Patterns

Top View

NOTE: the flashlight feature only initiates or restarts the
Test Mode and does not change any other sensor settings.

33ft
(10m)
27ft
(8m)
20ft
(6m)

Side Viewal

7.5ft
(2.3m)
0ft
(0m)

13ft
(4m)
7ft
(2m)
0ft
(0m)

7ft 13ft 20ft 27ft 33ft 40ft
(2m) (4m) (6m) (8m) (10m) (12m)

A

B

C

Zones

7ft
(2m)

A 18 Lower

13ft
(4m)
20ft
(6m)

B 46 Intermediate
C 36 Long

27ft
(8m)
33ft
(10m) 0ft 7ft 13ft 20ft 27ft 33ft 40ft
(0m) (2m) (4m) (6m) (8m) (10m) (12m)

Battery Replacement

1

Panasonic CR123A
Duracell DL123
Duracell DL123A
Honeywell 466

• Press the latch at the top of the device and slide
the front cover down to remove it.
• Remove the battery and wait 10 seconds, then
insert a new battery. Recommended batteries:
Panasonic CR123A Honeywell 466
Duracell DL123
Duracell DL123A
• Place the front and back covers together and slide
the front cover upward as shown.

5

4
3

2
0
10

45
30

BATTERY CAUTION: Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 212° F (100° C) or incinerate.
Dispose of used batteries properly. Keep away from children.

~

10 sec

Specifications

Approval Listings

Range: 40’ x 56’ / 12 m x 17 m
Wall Mounting Height: 7’ – 9’ (2.1 m – 2.7 m); Optimal 7’6” (2.3 m)
Battery: 1 x 3V, Lithium; Panasonic CR123A, Duracell DL 123A,
Duracell DL 123, Honeywell 466
RF Frequency: 2.4GHz
Tamper: Cover and Wall – reported separately to panel.
Operating Temperature: 32° – 122° F / 0° – 50° C (Agency Compliance 32° –
120° F / 0° – 49° C)
Relative Humidity: 95% max. (Agency Compliance - 93% max.),
non-condensing
Dimensions: 4.13” H x 2.38” W x 1.61” D / 105 mm H x 60.4 mm W x 41 mm D
Weight: 3.97 oz / 112.67g (net weight)

FCC / IC
cETLus Listed
Conforms to UL 639
Certified to ULC-S306-03
Other Standards:
SIA-PIR-01
RoHS
The product must be tested at least
once each year.

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.

FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les
interférences causant une reception indésirable.

RF EXPOSURE
Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter
product procedures.

Mise en Garde
Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins
7,8 pouces (20 cm) de toutes les personnes.

Support and Warranty
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

For the latest documentation and online support information, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
For patent information, see www.honeywell.com/patents

MyWebTech

Warranty

Patents

 2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved.

www.honeywell.com/security

2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747

DOC CODE 128B BAR CODE HERE
800-21341 11/15 Rev A