Telguard TG-7 Series - Quick Install Guide

Telguard TG-7 Series
QUICK INSTALLATION GUIDE [BACKUP MODE]
Installation Summary
There are seven steps in installing Telguard properly.
IF YOU DO NOT
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY
NOT COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
S
TEP
1:
R
EGISTER FOR
C
ELLULAR
S
ERVICE
The registration form may be completed online through our 24/7 dealer portal
www.telguard.com
.
S
TEP
2:
L
OCATE
U
NIT AND
M
EASURE
S
IGNAL
S
TRENGTH
(RSSI)
With the unit powered up, press the LED/RSSI Mode Toggle button one time, LEDs will now
indicate signal strength. Minimum recommended is 2 (2 on solid). Position the Telguard in a
location where minimum signal strength is satisfied. Press the LED/RSSI Mode Toggle button a
second time to exit RSSI mode.
S
TEP
3:
T
RANSMIT
P
ANEL
A
LARMS OVER THE
T
ELCO
C
ONNECTION
Verify the alarm panel is programmed properly by transmitting a signal over the telco connection.
This step is important to verify that the alarm panel is programmed with valid account code and
central station information before transmitting signals through the cellular network.
S
TEP
4:
P
ROGRAM
,
A
CTIVATE
&
T
RANSMIT
P
ANEL
A
LARMS OVER THE
C
ELLULAR
R
ADIO
N
ETWORK
Connect the alarm panel's digital dialer output to the Telguard and verify the alarm signals can be
reliably sent through Telguard over the cellular network to the central station digital receiver. The
incoming Telco line is
not
connected to Telguard during this step. A minimum of two alarm
signals must be transmitted. Activation is confirmed when LED 1 becomes illuminated.
(NOTE:
THE FIRST ALARM WILL ACTIVATE THE UNIT AT THE
T
ELGUARD
C
OMMUNICATION
C
ENTER
,
IT WILL NOT GO TO THE
C
ENTRAL
S
TATION
,
ALL SIGNALS AFTER THE FIRST ARE
SENT TO THE
C
ENTRAL
S
TATION
)
S
TEP
5:
C
ONNECT
S
UPERVISORY
T
RIP
O
UTPUTS
Wire the Telguard's supervisory trip outputs to the alarm panel and then test.
S
TEP
6:
C
ONNECT
T
RIP
I
NPUT
(
OPTIONAL
)
Wire an external relay to the trip input lead and ground, and test.
S
TEP
7:
C
OMPLETE THE
I
NSTALLATION
Attach earth ground to the Telguard, reconnect Telco, and permanently mount the unit. 56050102
2
4
H
O
U
R
Z
O
N
E
(
N
.
C
.
)
T
E
L
C
O
D
I
A
L
E
R
ANTENNA
T
R
www.Telguard.com
REFER TO INSTALLATION AND
OPERATING INSTRUCTIONS
MANUAL. THIS DEVICE COMPLIES
WITH FCC RULE PART 15.
SIM
CAUTION:
INCORRECT
CONNECTIONS MAY RESULT
IN DAMAGE TO UNIT.
LED Mode
Toggle Button
4
L
E
D
s
2
-
5
Signal (dBm)
NO
SVC
< -110
> -110
> -100
> -90
> -80
> -70
> -60
RSSI (bars)
NONE
1½1
2
2½
3
3½
System Status LEDs (RSSI Mode)
OFF
BLINKING
ON
OFF
BLINKING
ON
4
L
E
D
s
2
-
5
Signal (dBm)
NO
SVC
< -110
> -110
> -100
> -90
> -80
> -70
> -60
RSSI (bars)
NONE
1½1
2
2½
3
3½
System Status LEDs (RSSI Mode)
OFF
BLINKING
ON
Alarm Panel
1 FLASH = AC LOW/MISSING
2 FLASH = LBC LOW BATTERY
3 FLASH = LFC
4 FLASH = NSC NO SERVICE
5 FLASH = RFC RADIO FAILURE
6 FLASH = DTF DIAL TONE FAIL
7 FLASH = PPF PNL PRES FAIL
L
E
D
1
OFF
NOT ACTIVATED
ACTIVATED
ON
System Status LEDs (Normal Mode)
ACTIVATION DENIED
FLASHING
ACTIVATION
L
E
D
2
OFF
FLASHING
SYSTEM
TROUBLE
NO TROUBLE
TROUBLE:
L
E
D
3
OFF
ON
PANEL COMM
PANEL ON-HOOK (PRIMARY)
PANEL ON-HOOK (BACKUP)
L
E
D
4
OFF
IDLE
WAITING FOR RESPONSE
FROM TCC
ON
ACTIVATION DENIED
FLASHING
TCC COMM
L
E
D
5
OFF
IDLE
RADIO INITIALIZING
ON
RADIO COMMUNICATING
FLASHING
RADIO STATUS
Battery
Connector
Acceptable RSSI Range
Battery wire should
be at least ¼ inch
apart from AC wires
2
4
H
O
U
R
Z
O
N
E
(
N
.
O
.
)
WARNING:
HIGH VOLTAGE
PRESENT ON PHONE
LINES.
DISCONNECT PRIOR
TO SERVICING.
PANEL OFF-HOOKFLASHING
B
A
T
T
E
R
Y
B
A
T
T
E
R
Y
L
E
D
6
L
E
D
7
L
E
D
8
OFF
NOT USED
NOT USED
TRIP INPUT
AC NOT CONNECTED TO UNIT
AC CONNECTED TO UNIT
OFF
ON
POWER LED
FLASHING
5-MIN. SUPERVISION ENABLED
(2 FLASHES EVERY 6 SECONDS)
Alarm Panel
T
E
L
C
O
D
I
A
L
E
R
1
T
E
L
C
O
H
O
U
S
E
T
E
L
C
O
D
I
A
L
E
R
2
T
E
L
C
O
H
O
U
S
E
T
E
L
C
O
D
I
A
L
E
R
1
T
E
L
C
O
H
O
U
S
E
T
E
L
C
O
D
I
A
L
E
R
2
T
E
L
C
O
H
O
U
S
E
T
R
TG-7FS
TIP
RING
TIP1
RING1
TIP
RING
TIP1
RING1
OPTIONAL CONNECTION:
(TWO TELCO CONNECTIONS FROM THE
ALARM PANEL SPLICED INTO THE TG-7FS)
TELGUARD
Digital TG-7
EARTH
GROUND
AC
(12V 800MA)
TO EXTERNAL
TRIP INPUT
STC2
(N.C.)
STC1
(N.O.)
1
2
3
5 6
1
2
1
1
1
2
2
2
1
1
1
3
3
3
2
2
2
4
Optional
Battery
++
-
NOT ACTIVATED OR
RESTORED
ACTIVATED
OFF
ON
1
2
3
4
5
6
7
8
Power LED
System Status
LEDs
1
2
3
4
5
6
7
8
Power LED
System Status
LEDs
Telguard TG-7 Series
QUICK INSTALLATION GUIDE [SOLE PATH]
Installation Summary
There are seven steps in installing Telguard properly.
IF YOU DO NOT
PROCEED IN THE ORDER AND MANNER PRESCRIBED, YOU MAY NOT
COMPLETE THE INSTALLATION IN THE TIME ALLOCATED.
S
TEP
1:
R
EGISTER FOR
C
ELLULAR
S
ERVICE
The registration form may be completed online through our 24/7 dealer portal
www.telguard.com
.
S
TEP
2:
L
OCATE
U
NIT AND
M
EASURE
S
IGNAL
S
TRENGTH
(RSSI)
With the unit powered on, press the LED/RSSI Mode Toggle button one time, LEDs will now indicate
signal strength. Minimum recommended is 2 ½ (2 on solid and 1 flashing). Position the Telguard in a
location where minimum signal strength is satisfied. Press the LED/RSSI Mode Toggle button a
second time to exit RSSI mode.
S
TEP
3:
C
ONFIGURE
A
LARM
P
ANEL FOR
S
OLE
P
ATH
C
ONNECTION
Fire panels are typically provided with two Telco connections. Because the TG-7 provides a single
connection, the panel must be set up accordingly. The first method of installation is to configure the
panel to disable the second Telco connection. If this is not an option due to panel limitations, it is
possible to splice both TIP and RING connections from the panel into the single jack of the
Telguard. The TG-7 is capable of providing dial tone to both Telco connections.
S
TEP
4:
A
CTIVATE
&
T
RANSMIT
P
ANEL
A
LARMS OVER THE
C
ELLULAR
R
ADIO
N
ETWORK
Make sure to select Sole Path communication for your Telguard during the registration process.
LED 3 will be off when idle, if successful. Connect the alarm panel's digital dialer output to Telguard
and verify that alarm signals can be reliably sent through Telguard over cellular to the central
station digital receiver. A minimum of two alarm signals must be transmitted.
Activation is
confirmed when LED 1 is illuminated.
(NOTE:
THE FIRST ALARM WILL ACTIVATE THE UNIT AT THE
T
ELGUARD
C
OMMUNICATION
C
ENTER
,
IT WILL NOT GO TO THE
C
ENTRAL
S
TATION
,
ALL SIGNALS AFTER THE FIRST ARE
SENT TO THE
C
ENTRAL
S
TATION
)
S
TEP
5:
C
ONNECT
S
UPERVISORY
T
RIP
O
UTPUTS
Wire Telguard's supervisory trip outputs to the alarm panel and test.
S
TEP
6:
C
ONNECT
T
RIP
I
NPUT
(
OPTIONAL
)
Wire an external relay input to the trip input lead and ground, and test.
S
TEP
7:
C
OMPLETE THE
I
NSTALLATION
Attach earth ground to the Telguard, and permanently mount the unit.