WBOX 0E-SNGPR319 - Installation & Setup Guide - 3/22

0E-SNGPR319

319MHz Wireless Sensor

(QOLSYS
®
/ITI/GE Compatible)
Installation & Setup Guide

FEATURES
•
Single zone Door/Window Transmitter
•
Compatible with QOLSYS/ITI/GE alarm systems that
support 319 MHz wireless devices
•
Built-in unique serial number which must be enroll
ed into
the control panel
•
Refer to the control panel’s installation instruct
ions for
programming details.

5800MIMI-001-V0

LED Indicators
LED

Meaning

Blue
Lights when the magnet is within proper range of th
e sensor (1 inch max).
LED is active for 15 minutes after battery is first
installed or when the cover
is removed.

Green
Flashes when the sensor transmits. LED is active fo
r 15 minutes after
battery is first installed or when cover is removed
.

Red
Upon low battery condition, flashes once about ever
y five seconds for two
minutes after a transmission
.


MOUNTING
•
Choose a mounting location where the device is sta
tionary and the magnet is
mounted to the moving part of the door or window.
•
Verify adequate signal strength by using the contr
ol panel’s Go/No Go test (see
control’s instructions) before mounting permanently
.
•
Avoid mounting in areas where it will be exposed t
o moisture or where the operating
temperature of 32 to 120ºF (0 to 50ºC) will be exce
eded.
•
Keep the sensor and magnet away from metal or meta
llic surfaces such as foil
wallpaper.
•
Avoid mounting the sensor in areas with a large qu
antity of metal or electrical wiring,
such as a furnace or utility room.


1.
Install the Battery

a. Open the cover.
b. Install the battery with “
+
++
+
” side up.
c. Replace the cover.

The blue and green LEDs will be active for 15
minutes. To reactivate, remove the cover.
2.
Mount the Sensor & Magnet

a. Mount the sensor on the frame of the protected
door or window using double-faced tape

(supplied).
b
.
Mount the magnet

(supplied) on the protected
door or opening portion of the protected
window. Check that the blue LED lights when
the door or window is closed.

5800MIMI-002-V0

5800MIMI-009-V0


5800MIMI-008-V1
CORRECT
INCORRECT
X
PROGRAMMING
Refer to the control panel’s installation instructi
ons for programming and enrolling the
sensor.
BATTERY REPLACEMENT
1. Open the cover and remove the old battery.
2. Install a fresh battery with
+
++
+
side UP. See Specifications
section for compatible batteries.
3. Replace the cover.

BATTERY CAUTION
: Risk of fire, explosion and burns. Do
not recharge, disassemble, heat above 212°F (100°C)
, or
incinerate. Dispose of used batteries properly. Kee
p away
from children.
Attention de batterie: Risque d'incendie, d'explosi
on et de
brûlures. Ne rechargez pas, démonter, chauffer au-d
essus de
212° F (100°C), ou incinérer. Débarrassez-vous des
batteries
utilisées de façon appropriée. Gardez à partir des
enfants.

SPECIFICATIONS


5800MIMI-010-V0
TAMPER
REED


5800MIMI-002-V0

5800MIMI-005-V0


Dimensions:
Transmitter: 1” (25.4mm) x 2.2” (55.9mm) x 0.25”
(6.4mm)
Magnet:
0.25”
(6.35
m
m)

x 0.25”
(6.35mm)

x 1” (25.
4mm)

Operating Conditions:
32
°F
(0
°
C) to 120
°F
(50
°
C)

Relative Humidity 95%, (non
-
condensing); UL Tested at 85%

Magnet Gap:

1” (25.4mm) max.

Battery:
3VDC, 225mAh, Lithium Coin Cell;
Panasonic CR2032


FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modification
s to the equipment unless authorized by the Install
ation Instructions or
User Manual. Unauthorized changes or modifications
could void the user's authority to operate the equi
pment
FCC/IC STATEMENT
This device complies with Part 15 of the FCC Rules,
and Industry Canada’s license-exempt RSSs. Operati
on is subject to
the following two conditions: (1) This device may n
ot cause harmful interference (2) This device must
accept any interference
received, including interference that may cause und
esired operation.
Cet appareil est conforme à la partie 15 des règles
de la FCC et exempt de licence RSS d’Industrie Can
ada. Son
fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d' interférenc
es nuisibles. (2) Cet
appareil doit accepter toute interférence reçue y c
ompris les interférences causant une réception indé
sirable.


REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONT
ROL WITH WHICH THIS DEVICE IS USED FOR
DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM S
YSTEM.

The product should not be disposed of with other ho
usehold waste. Check for the nearest authorized col
lection centers or
authorized recyclers. The correct disposal of end-o
f-life equipment will help prevent potential negati
ve consequences for the
environment and human health.

SUPPORT & WARRANTY
For online support information, please go to: www.r
esideo.com
For the latest warranty information, please go to:
www.adiglobal.com


All

®
trademarks are the property if their respective own
ers



R800-27518A 3/22 Rev A


ADI Global Distribution
275 Broadhollow Road
Melville, NY 11747

www.
adiglobal
.com