Winland TA-40 - Install Guide - Dated 08/2012 Rev. B

Fixed Set Point Temperature Alert (40° F)
S
PECIFICATIONS
Power Requirement
No power required to operate.
Fixed Setting
N.O. ≤ 39.2° F (4° C)
Temp Accuracy
±5.4° F (±3° C)
Temp Sensing Element
Bimetallic
Outputs
N.C. dry contact (
Not for high voltage use.
)
Contact Output Rating
200mA @ 24VDC/VAC
Operating Temperature
-40 to 212 ̊ F (-40 to 100 ̊ C); non-condensing environment.

Indoor use only.
Weight
3 oz (85 g)
Dimensions
2.5 x .8 x 0.55” (6.4 x 2 x 1.4 cm)
Material
ABS
Mounting
2 screw holes (0.165” [0.42 cm] diameter)
C
ONTENTS
This package contains:
• 1 TA-40
• 1 Installation/Operating Instructions Guide
TA-40
O
NE
Y
EAR
L
IMITED
W
ARRANTY
Winland Electronics, Inc. (“Winland”) warrants to the end user/purchaser that each product of its manufacture shall be free from defects in material
and factory workmanship for a period of one year from the date of purchase, when properly installed and operated under normal conditions
according to Winland’s instruction.
Winland’s obligation under this warranty is limited to correcting, without charge, at its factory any part or parts thereof which shall be returned to
the factory, by the original purchaser, transportation charges prepaid, within one year of the date of purchase and which upon examination, shall
disclose to Winland’s satisfaction to have been originally defective. Correction of such defects by repair to, or supplying replacements for, defective
parts shall constitute fulfillment of all Winland’s obligations to purchaser under this limited warranty. Repair service performed by Winland after one
year from date of purchase will be for a reasonable service charge.
This limited warranty shall not apply to any of Winland’s products which have been subject to misuse, negligence or accident or which have been
repaired or altered outside of Winland’s factory. The warranty is void if the Product’s housing or cover is removed.
Winland shall not be liable for loss, damage or expense resulting, directly or indirectly, from the use of its products or any other cause.
This warranty shall be null and void in its entirety if: (i) the product is altered or modified in any way that is not consistent with the manufacturer’s
instructions, or (ii) the product is used with or connected to a device: (a) that such product is not intended to be used with or connected to, (b) is not
otherwise consistent with the manufacturer’s instructions, or (c) is not otherwise approved by the manufacturer.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES, NON-INFRINGEMENT AND TITLE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING,
USAGE OF TRADE OR OTHERWISE. ALL OTHER REPRESENTATIONS MADE TO THE END USER/PURCHASER BY ANY OTHER PARTY ARE ALSO EXCLUDED.
WINLAND SHALL NOT BE LIABLE TO ANY PERSON FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY DESCRIPTION, WHETHER
ARISING OUT OF WARRANTY OR OTHER CONTRACT, NEGLIGENCE OR OTHER TORT, OR OTHERWISE. Under no circumstances shall Winland’s liability
under this limited warranty exceed the purchase price paid by the end user/purchaser for the product.
No person, agent or dealer is authorized to give warranties on behalf of Winland nor to assume for Winland any other liability in connection with
any of its products.
© 2012 Winland Electronics, Inc.
D-011-0115 Rev B (08/2012)
Tech Support 8:00am - 5:00pm Central Time
(800) 635-4269 • +1-507-625-7231 P
www.winland.com
WEEE Product Recovery/Recycling for EU Customers
In an effort to improve waste management in the European Union, the European Union has enacted directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE Directive). According to the WEEE Directive, Winland Electronics must take back waste electrical or electronic equipment
covered under the WEEE Directive, at its cost, for all product it puts on the market after July 1, 2006. The Return Process: Contact Winland via our web
site at www.winland.com.
Applicable Directives
RoHS Directive 2002/95/EC; WEEE Directive 2002/96/EC
Statement of Compliance:
Winland Electronics, Inc. hereby declares this device is in compliance with all the applicable Directives 2002/95/EC, 2002/96/EC. This device is
considered a passive EM device and is thereby excluded from the scope of the EMC directive 89/336/EEC and Low Voltage Directive 73/23/EEC.
Symbols on the Product or Manual Labeling
For product disposal, ensure the following:
• Do not dispose of this product as unsorted municipal waste.
• Collect this product separately.
• Use collection and return systems available to you.
WEEE Waste Electrical and Electronic Equipment
RoHS Restriction of Hazardous Substances I
NTRODUCTION
Thank you for your purchase of the Winland Temp ̊Alert® model TA-40. Your new Temp ̊Alert® has been designed for
reliable monitoring of areas where low temperature limits are critical. Temp ̊Alert® monitors and activates when the
temperature drops below 39.2 ̊ F (4 ̊ C).
L
OCATION
It is difficult to precisely specify the location or quantity of TA-40s to install. A number of factors such as room size,
effectiveness of the ventilation system, and the likelihood of freezing should be considered. If the building already has
an energy management system, an easy rule of thumb is to install a TA-40 near each thermostat. When protecting a
building against freeze damage, always install at least one Temp ̊Alert® on every level of the home or business.
I
NSTALLATION
Items needed:
• Either Standard or Phillips screwdriver
• Quantity of two (2) #6 Screws
• 22-18 AWG twisted pair
Step 1
Use the base of the TA-40 as a template and mark the position of the screw holes. Drill pilot holes if necessary.
Align the TA-40 with mounting holes and install the screws. Do not fully tighten screws at this time.
Step 2
Connect the TA-40 to your warning device by attaching an 22-18 AWG twisted pair cable to the terminals. Slide
the cover on and finish tightening the mounting screws.
Operation and Testing Procedures
The TA-40 must be located in an area where the temperature range is within -40 ̊ to 212 ̊ F (-40 ̊ to 100 ̊ C). Contacts
will remain closed at temperatures above 39.2 ̊ F (4 ̊ C). But if the temperature drops below 39.2 ̊ F (4 ̊ C) the
contacts will open to activate any hardwire alarm or wireless transmitter. The tolerance on this temperature switch is
±5.4 ̊ F.
To manually activate the TA-40 for testing purposes, place the device in a freezer for 10 minutes. Remove the TA-40
from the freezer; test the contacts with an ohmmeter to confirm they have opened.
To insure proper operation, test weekly.
TA-1
Single output temperature monitoring
No power required to operate.
50 to 130°F alarm range; non condensing environments only.
N.O. dry contacts.
Not for use in coolers and freezers.
TA-2HL
Dual output temperature monitoring
No power required to operate.
50 to 130°F alarm range; non condensing environments only.
N.O. dry contacts.
Not for use in coolers and freezers.
MTA-1
Dual output temperature monitoring
No power required to operate.
50 to 100°F alarm range; non condensing environments only.
N.O. dry contacts.
Not for use in coolers and freezers.
A
DDITIONAL
T
EMP
°A
LERT
® P
RODUCTS
I
MPORTANT
:
Do not place any Temp ̊Alert® in a cooler or freezer. Frost buildup and
moisture can cause the unit to malfunction. For cooler & freezer
applications, use an EnviroAlert® device with a remote probe. I
NTRODUCTION
Thank you for your purchase of the Winland Temp ̊Alert® model TA-40. Your new Temp ̊Alert® has been designed for
reliable monitoring of areas where low temperature limits are critical. Temp ̊Alert® monitors and activates when the
temperature drops below 39.2 ̊ F (4 ̊ C).
L
OCATION
It is difficult to precisely specify the location or quantity of TA-40s to install. A number of factors such as room size,
effectiveness of the ventilation system, and the likelihood of freezing should be considered. If the building already has
an energy management system, an easy rule of thumb is to install a TA-40 near each thermostat. When protecting a
building against freeze damage, always install at least one Temp ̊Alert® on every level of the home or business.
I
NSTALLATION
Items needed:
• Either Standard or Phillips screwdriver
• Quantity of two (2) #6 Screws
• 22-18 AWG twisted pair
Step 1
Use the base of the TA-40 as a template and mark the position of the screw holes. Drill pilot holes if necessary.
Align the TA-40 with mounting holes and install the screws. Do not fully tighten screws at this time.
Step 2
Connect the TA-40 to your warning device by attaching an 22-18 AWG twisted pair cable to the terminals. Slide
the cover on and finish tightening the mounting screws.
Operation and Testing Procedures
The TA-40 must be located in an area where the temperature range is within -40 ̊ to 212 ̊ F (-40 ̊ to 100 ̊ C). Contacts
will remain closed at temperatures above 39.2 ̊ F (4 ̊ C). But if the temperature drops below 39.2 ̊ F (4 ̊ C) the
contacts will open to activate any hardwire alarm or wireless transmitter. The tolerance on this temperature switch is
±5.4 ̊ F.
To manually activate the TA-40 for testing purposes, place the device in a freezer for 10 minutes. Remove the TA-40
from the freezer; test the contacts with an ohmmeter to confirm they have opened.
To insure proper operation, test weekly.
TA-1
Single output temperature monitoring
No power required to operate.
50 to 130°F alarm range; non condensing environments only.
N.O. dry contacts.
Not for use in coolers and freezers.
TA-2HL
Dual output temperature monitoring
No power required to operate.
50 to 130°F alarm range; non condensing environments only.
N.O. dry contacts.
Not for use in coolers and freezers.
MTA-1
Dual output temperature monitoring
No power required to operate.
50 to 100°F alarm range; non condensing environments only.
N.O. dry contacts.
Not for use in coolers and freezers.
A
DDITIONAL
T
EMP
°A
LERT
® P
RODUCTS
I
MPORTANT
:
Do not place any Temp ̊Alert® in a cooler or freezer. Frost buildup and
moisture can cause the unit to malfunction. For cooler & freezer
applications, use an EnviroAlert® device with a remote probe. Fixed Set Point Temperature Alert (40° F)
S
PECIFICATIONS
Power Requirement
No power required to operate.
Fixed Setting
N.O. ≤ 39.2° F (4° C)
Temp Accuracy
±5.4° F (±3° C)
Temp Sensing Element
Bimetallic
Outputs
N.C. dry contact (
Not for high voltage use.
)
Contact Output Rating
200mA @ 24VDC/VAC
Operating Temperature
-40 to 212 ̊ F (-40 to 100 ̊ C); non-condensing environment.

Indoor use only.
Weight
3 oz (85 g)
Dimensions
2.5 x .8 x 0.55” (6.4 x 2 x 1.4 cm)
Material
ABS
Mounting
2 screw holes (0.165” [0.42 cm] diameter)
C
ONTENTS
This package contains:
• 1 TA-40
• 1 Installation/Operating Instructions Guide
TA-40
O
NE
Y
EAR
L
IMITED
W
ARRANTY
Winland Electronics, Inc. (“Winland”) warrants to the end user/purchaser that each product of its manufacture shall be free from defects in material
and factory workmanship for a period of one year from the date of purchase, when properly installed and operated under normal conditions
according to Winland’s instruction.
Winland’s obligation under this warranty is limited to correcting, without charge, at its factory any part or parts thereof which shall be returned to
the factory, by the original purchaser, transportation charges prepaid, within one year of the date of purchase and which upon examination, shall
disclose to Winland’s satisfaction to have been originally defective. Correction of such defects by repair to, or supplying replacements for, defective
parts shall constitute fulfillment of all Winland’s obligations to purchaser under this limited warranty. Repair service performed by Winland after one
year from date of purchase will be for a reasonable service charge.
This limited warranty shall not apply to any of Winland’s products which have been subject to misuse, negligence or accident or which have been
repaired or altered outside of Winland’s factory. The warranty is void if the Product’s housing or cover is removed.
Winland shall not be liable for loss, damage or expense resulting, directly or indirectly, from the use of its products or any other cause.
This warranty shall be null and void in its entirety if: (i) the product is altered or modified in any way that is not consistent with the manufacturer’s
instructions, or (ii) the product is used with or connected to a device: (a) that such product is not intended to be used with or connected to, (b) is not
otherwise consistent with the manufacturer’s instructions, or (c) is not otherwise approved by the manufacturer.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES, NON-INFRINGEMENT AND TITLE, AND ANY WARRANTIES ARISING FROM COURSE OF DEALING,
USAGE OF TRADE OR OTHERWISE. ALL OTHER REPRESENTATIONS MADE TO THE END USER/PURCHASER BY ANY OTHER PARTY ARE ALSO EXCLUDED.
WINLAND SHALL NOT BE LIABLE TO ANY PERSON FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY DESCRIPTION, WHETHER
ARISING OUT OF WARRANTY OR OTHER CONTRACT, NEGLIGENCE OR OTHER TORT, OR OTHERWISE. Under no circumstances shall Winland’s liability
under this limited warranty exceed the purchase price paid by the end user/purchaser for the product.
No person, agent or dealer is authorized to give warranties on behalf of Winland nor to assume for Winland any other liability in connection with
any of its products.
© 2012 Winland Electronics, Inc.
D-011-0115 Rev B (08/2012)
Tech Support 8:00am - 5:00pm Central Time
(800) 635-4269 • +1-507-625-7231 P
www.winland.com
WEEE Product Recovery/Recycling for EU Customers
In an effort to improve waste management in the European Union, the European Union has enacted directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE Directive). According to the WEEE Directive, Winland Electronics must take back waste electrical or electronic equipment
covered under the WEEE Directive, at its cost, for all product it puts on the market after July 1, 2006. The Return Process: Contact Winland via our web
site at www.winland.com.
Applicable Directives
RoHS Directive 2002/95/EC; WEEE Directive 2002/96/EC
Statement of Compliance:
Winland Electronics, Inc. hereby declares this device is in compliance with all the applicable Directives 2002/95/EC, 2002/96/EC. This device is
considered a passive EM device and is thereby excluded from the scope of the EMC directive 89/336/EEC and Low Voltage Directive 73/23/EEC.
Symbols on the Product or Manual Labeling
For product disposal, ensure the following:
• Do not dispose of this product as unsorted municipal waste.
• Collect this product separately.
• Use collection and return systems available to you.
WEEE Waste Electrical and Electronic Equipment
RoHS Restriction of Hazardous Substances