Winland WBTX319 and Winland WBTX345 Wireless WaterBug - Install Guide

Wireless WaterBug Sensor
© 2017 Winland Electronics, Inc.

D-001-0174
Contents
T
his package contains:

•
1 Transmitter (includes batteries)
•
1 Surface Probe
•
1 Quick Start Guide
• 2 Mounting Screws
• 2 Adhesive Strips
Tech Support 8:00am - 5:00pm Central Time
(800) 635-4269
techsupport@winland.com
www.winland.com
I
nstallatIon
When mounting the transmitter, make sure it is not mounted on metal or where
there are any large metal objects between the device and the alarm panel, this
can be tested prior to or after installation.
Mounting the probe to a vertical surface like a wall enables you to monitor an
area for rising water levels. Use where ever unwanted water may accumulate.
Suggested areas near: water heater, washing machines, under sinks, and sump
pumps.
Water Detector Mounting:
Mount the transmitter as high as possible, the water probe has a 6’ cable
attaching it to the transmitter. The probe can be mounted to the wall or floor
using mounting screws or adhesive strips provided.
Mount Transmitter
using supplied
adhesive strips
Probe mounts directly
to the floor or can be
attached to a wall, using
adhesive strips or screws
I
ntroductIon
Thank you for your purchase of the Winland Wireless WaterBug® model
WBTX. The WBTX is completely electronic and is designed to detect
water.

The WBTX is not a self-contained warning device. For proper operation, it
must be used in conjunction with a wireless alarm system. It is designed
so that the transmitter mounts on a wall or other flat vertical surface, and
the remote probe is placed in the location where water leakage is most
probable.


Moisture forming a bridge between the two metallic contacts on
a remote probe is all that is needed for the unit to signal an alarm
condition. The output on the WBTX will remain in alarm state until the
moisture bridge is broken. As sensitive as the WBTX is, it will not alarm
due to high humidity or condensation. The WBTX is ideal for use in
homes, offices, computer rooms, warehouses, etc.
Surface Probe
• Above floor detection
• On floor detection
• 6’ Cord length
Transmitter
• Cover (tamper proof )
• Battery checked every hour
• Batteries (2) CR2032
Approximate Battery Life - 5 years

Replace Batteries: (2) Panasonic CRT2032,
Energizer CR2032, or Duracell DL2032
NOTE:
Keep batteries away from children

• Tamper Switch: Included inside transmitter

WBTX-319
WBTX-345
Wireless WaterBug Sensor and Accessories
1 Transmitter • 1 Probe • 2 Adhesive Strips • 2 Batteries • 2 Screws
Wireless

Installation Instructions Mount the probe to
ensure these two
metallic

contacts are near the
surface to be monitored,
but not touching the
surface
To insure proper operation, test weekly.
Concrete can be semi-conductive.
If experiencing false alarms, insulate all
probes mounted on concrete.
Features
• Water Detection when liquid makes contact with probe
• Contacts above floor level to prevent false floor condensation detection
• Checks for water constantly, requires two positive checks for a valid alarm



Programming

1. Enable Programming Mode
2. Open and close the case to “tamper” the device
3. Customize name and settings as desired and touch “ADD”
Probe
O
ne
Y
ear
L
imited
W
arrant
Y
Winland Electronics, Inc. (“Winland”) warrants to the end user/purchaser that each product of its manufacture shall be free from defects
in material and factory workmanship for a period of one year from the date of purchase, when properly installed and operated under
normal conditions according to Winland’s instruction. Winland’s obligation under this warranty is limited to correcting, without charge,
at its factory any part or parts thereof which shall be returned to the factory, by the original purchaser, transportation charges prepaid,
within one year of the date of purchase and which upon examination, shall disclose to Winland’s satisfaction to have been originally
defective. Correction of such defects by repair to, or supplying replacements for, defective parts shall constitute fulfillment of all Winland’s
obligations to purchaser under this limited warranty. Repair service performed by Winland after one year from date of purchase will be
for a reasonable service charge. This limited warranty shall not apply to any of Winland’s products which have been subject to misuse,
negligence or accident or which have been repaired or altered outside of Winland’s factory. The warranty is void if the Product’s housing
or cover is removed.
Winland shall not be liable for loss, damage or expense resulting, directly or indirectly, from the use of its products or any other cause.
This warranty shall be null and void in its entirety if: (i) the product is altered or modified in any way that is not consistent with the
manufacturer’s instructions, or (ii) the product is used with or connected to a device: (a) that such product is not intended to be used with
or connected to, (b) is not otherwise consistent with the manufacturer’s instructions, or (c) is not otherwise approved by the manufacturer.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES, NON-INFRINGEMENT AND TITLE, AND ANY WARRANTIES ARISING FROM COURSE
OF DEALING, USAGE OF TRADE OR OTHERWISE. ALL OTHER REPRESENTATIONS MADE TO THE END USER/PURCHASER BY ANY OTHER PARTY
ARE ALSO EXCLUDED. WINLAND SHALL NOT BE LIABLE TO ANY PERSON FOR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY DESCRIPTION, WHETHER ARISING OUT OF WARRANTY OR OTHER CONTRACT, NEGLIGENCE OR OTHER TORT, OR OTHERWISE. Under
no circumstances shall Winland’s liability under this limited warranty exceed the purchase price paid by the end user/purchaser for the
product. No person, agent or dealer is authorized to give warranties on behalf of Winland nor to assume for Winland any other liability in
connection with any of its products.
S
pecificationS

Power Requirement Batteries: 2 - CR2032 Approximate Battery Life: 5 years


Replace Batteries: (2) Panasonic CRT2032, Energizer CR2032, or Duracell DL2032
Wireless Signal Range 600 ft (200M), open air
Code Outputs
tamper, tamper restore, alarm, alarm restore, low battery

Transmitter frequency
319.5 MHz and 345MHz

Unique Code ID


Supervisory keep-alive interval
70 minutes

RF Peak field strength
Typical 36000 uV/m at 3m
Operating Temperature
32° to 122°F (0° to 50°C)
Storage Temperature
-40° to 140°F (-40° to 60°C)
Max Cable Length
72”

Package Weight
.158 lbs

Transmitter Dimensions 2.71” H x .95” W x .56” D

Probe Dimensions

.7” W x 1.77” L x .38” D
Mounting Probe
Can be mounted to wall surfaces using the provided
mounting screws or adhesive tape provided
Case Material
ABS
Warranty
1 Year Limited

Test Procedures
To test the WBTX operational status, form a water bridge between the two
metallic contact points (See figure 3) with a moistened finger or cloth. If work
-
ing properly, the WBTX will activate the warning device to which it is connected
within approximately three seconds. The WBTX will reset automatically when
the probe dries and there is no longer a water bridge between the two metallic
contact points.
1950 Excel Drive, Mankato, MN 56001 • 800-635-4269 • www.winland.com
© 2017 Winland Electronics, Inc.
D-001-0174
Cover Latch
Tamper Switch
Battery