First Alert CAMW-WI VX5 - Installation Instructions - Dated 11/2023 Rev B

Installation Guide
VX5 HD Video
Indoor Camera
www.resideo.com
Online Guides
Connect Cable to Device
Connect the cable to the back of the
camera.
Attach Camera to the Mounting Bracket
Align and snap the camera to the
mounting bracket while routing the cable
through the drilled hole.
Position Camera
Position the camera to point at the
desired area. Ensure the First Alert logo
is positioned correctly.
Note:
For best night vision quality, avoid
placing objectswithin 4 inches of the
camera or placing the camera too close
to a wall or reflective surface.
5.
6.
7.
Route Cable Through Drilled Hole
Route the cable through the hole drilled
previously. Make sure the cable doesn’t
retract.
4.
Included in the Box
Wall Anchors
Camera
Mounting Bracket
12V Power Adapter
Wall Screws
Phillips #2 screwdriver
Drill
Home Wi-Fi Password
Tools you will need
:
You may need
:
IMPORTANT: Before Installation
End-user operation requires an account and a mobile app. See
setup
requirements below:
Use the app for step-by-step install and
setup instructions.
Or continue steps 1 to 4 below...
From the App, add the device from the menu or camera screen.
Select the correct device
Follow the in-app instructions.
Connectivity
The camera supports Wi-Fi connectivity. Continuous 2 Mbps upload or faster Internet connection is required.
Mounting Installation
1
3
4
1
2
3
Drill Hole Through Mounting Surface
The recommended drill bit size is 5/8in
(16mm) or larger.
Align and Install the Mounting Bracket
Align the mounting bracket’s center
opening with the hole you drilled.
Screw the mounting bracket to the
surface with the screws provided. If
necessary, use the included wall anchors.
1.
2
2.
5/8 in (16mm)
Power Adapter
5a
4
Route the included power adapter cable
from the intended wall outlet to the
install location. Do not plug the power
adapter into the wall at this time.
3.
Cable and Power Installation
Camera Installation
7
When the power is on, wait for the LED
to flash blue. This indicates BLE pairing
mode.
Follow instructions in the app to
complete setup.
2.
Connect the power supply.
1.
3.
Connecting to the App
6
Steps 1-3 may be skipped if not mounting to wall or ceiling.
+
+
5/8 in (16mm)
1/4 in (6mm)
®
1. Read these instructions carefully; failure to follow the instructions can damage the product or cause a hazardous condition.
2. Check the product information to see if the product is suitable for your application.
3. Installer must be a trained, experienced service technician.
4. After completing installation, use these instructions to verify the product’s operation.
Note:
Verify a minimum signal strength of -65dBm at the installation location to ensure reliable and
timely video transmission
Note: Mounting Bracket Installation
If the device is not being mounted onto a wall or ceiling, install
the mounting bracket into the base of the device before placing
it at the intended installation location. Troubleshooting
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes
or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient or relocate the receiving antenna.
• Move the radio or television receiver away from the receiver/control.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC / ISED STATEMENT
This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception
indésirable.
RF EXPOSURE STATEMENT:

The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures.
MISE EN GARDE EXPOSITION AUX FRÉQUENCES RADIO:
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas
être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED.
FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS
Camera Specifications
Part Number....................................................................................................................................................CAMW-WI
Operating Temperature................................................................................................
......32 ̊F to 104 ̊F (0 ̊C to 40 ̊C)
Operating Humidity.........................................................................................................
....10 to 85% Non-condensing
Shipping Temperature......................................................................................................-4 ̊F to 158 ̊F (-20 ̊C to 70 ̊C)
Shipping Humidity.........................................................................................................
......10 to 95% Non-condensing
Physical Dimensions............................
.................................................
........2.57 x 2.52 x 5in (65.2 x 64.0 x 88.9mm)
Weight........................................................................................................................................................
5.2 Oz (147g)
Color.............................................................................................................................................
...........................White
Power Input..........................................................................................................................
...................
..............12VDC
Connectivity...
......................................................
.Continuous 2 Mbps upload or faster, minimum -65 dBm required
Privacy Shutter/
Reset Button
Location
Removing Camera
Light On Device
Light Color
Device Status
LED
White
Solid/Dim
White
Slow Pulse
White
Pulsing
Firmware Update
Wait for update to complete
White
Green
Solid
Blue
Slow Pulse
Blue
Solid
Bluetooth Pairing
Wi-Fi pairing and registration
Installation
In Use
Note/Resolution
Red
2 Rapid Pulse
Error/Setup Fail
Follow in-app Troubleshooting
Green
2 Rapid Pulse
Success/Confirmation
No Light
No Power
Check wiring connections
Yellow
Solid 5 Sec
Forced Reboot (Reset button pressed)
No Light
Lighting Functions
Light Behavior
Red
Solid 5 Sec
t
o Cycle
Fac
t
ory Reset (Reset but
t
on held)
SU
P P
O
RT

&
W
A RRANTY

For
t
he
lat
e
st
docume
nta
tio
n

an
d o
nl
i
n
e
s
uppor
t
i
n
form
a
tio
n
, p
l
e
as
e go
t
o:

www.re
s
ideo.com
For
t
he
lat
e
st
w
a
rr
ant
y i
n
form
a
tio
n
, p
l
e
as
e go
t
o:

www.re
s
ideo.com
R
e
s
po
ns
ib
l
e
Pa
r
t
y /
Iss
uer of Supp
l
ier’
s
Dec
la
r
a
tio
n
of
C
o
n
formi
t
y:
A
demco
In
c.,
a

s
ub
s
idi
a
ry of
R
e
s
ideo
T
ech
n
o
l
ogie
s
,
In
c.
2
C
orpor
at
e
C
e
nt
er Dr., Me
l
vi
ll
e,
NY

117
4
7
,
P
h:
516
-577-2000
T
hi
s
produc
t
m
an
uf
a
c
t
ured by
R
e
s
ideo Technologies, Inc. and its affiliates




www.resideo.com

R
e
s
ideo
T
ech
n
o
l
ogie
s
,
In
c

2
C
orpor
at
e
C
e
nt
er Drive, Sui
t
e
1
00

P
.O. Box
9
040 , Me
l
vi
ll
e,
NY

117
4
7

©
2024

R
e
s
ideo
T
ech
n
o
l
ogie
s
,
In
c.
All
righ
ts
re
s
erved.

R800-28435B 11/23 Rev. B
To remove the camera from the mounting bracket, press
into the side of the mounting base with a flathead
screwdriver or similar tool.
Removing the Camera
The reset button is located on the side of the device as seen
below right.*
Accessing the Reset Button
If the light does not come on, check that the power is on
and the correct cables are connected.
Camera does not Power On
To force reboot for any reason, press the Reset button for 5
seconds.*
Forced Reboot
To factory reset for any reason, press the Reset button for
25 seconds until the Status LED turns red.*
Factory Reset
If the blue light does not illuminate, press the reset button
for 10 seconds to initiate pairing mode.
Camera not in Pairing Mode
This equipment should be installed in accordance with National Electrical Code, NFPA 70, Standard for the Installation of Residential Fire
Warning Systems, CAN/ULC-S540 and Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72 (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269). Printed information describing proper installation, operation, testing, maintenance, evacuation
planning, and repair service is to be provided with this equipment.

Canadian Installations
For Installation in Canada, wiring shall be in accordance with CSA C22.1, Canadian Electrical Code, Part I, Safety Standard for Electrical
Installations ; CAN/ULC S302, Standard for the Installation, Inspection and Testing of Intrusion Alarm Systems; and CAN/ULC S301, Standard for
ignal Receiving Centre Intrusion Alarm Systems and Operations.
Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly
prohibited.
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers.
The correct disposal of end-of-life equipment will help prevent potential negative consequences for the environment and human health.
Follow in-app Bluetooth pairing
instructions
Camera is starting. Bluetooth
pairing will begin automatically.
Idle. Capturing and processing images
Lighting may be disabled in the app
Event Detected. Clip Recording
Solid Bright
Live Viewing and Two-Way Audio
No Power or Lighting Disabled
Note: “In Use” lighting may be disabled through app settings. Ensure the device complies with local laws and regulations.
LED will also turn solid green when the
camera's Live View is being watched
in TC2
*
*If you are still experiencing issues, follow the setup
instructions in the app
Two-Way Communication activated
in Live View*