Honeywell Home PROLTE-ANT Installation Instructions - Dated 6/19 Rev. B

PRO
LTE
-
A
NT


External Fixed Length Antenna



Installation
and Setup
Guide

GENERAL
INFORMATION

The
PROLTE
Series
Communication Modules
use
an internal multi
band cellular antenna. In most cases
, this
antenna will provide sufficient
quality of signal
(QOS
) for
a successful ins
tallation.

Compatible Control Panels:
PRO
Series
Control
Panels

The
PRO
LTE
-ANT
Fixed Length Antenna
should be used in installations where moving the antenna to a higher
point will provide
a better
quality of signal
.
Installation
Note:

For
the
best
QOS
, maintain at least 12 inches of clearance between the
communication
module
and steel I
-beams, HVAC ducts, metal studs, steel roofs, exterior walls with
metalized insulation or aluminum siding and other large metal objects.

Kit Includes:

M
ulti band cellula
r a
ntenna
with double sided adhesive


Integrated coax cable with
SMA
to MMCX adapter cable


Antenna
mounting
hardware
pack
: 2 cable clamps with screws and anchors



Compatible Modules:

PROLTE-
A (US
/Canada, AT&
T Network
),

PROLTE-
V (
US, Verizon Network)
,

PROLTE-
CN (Canada Bell Network)


INDOOR/OUTDOOR
ANTENNA

The
antenna
is water
proof
, and
can
be installed indoors
or outdoors.
The antenna should be mounted on a
glass, plastic, drywall, masonry or wood surface verti
cally
, while maintaining 12 inches of c
learance from large
metal object
s. Do not install on a metal surface.


PROA7
Series

Installation

Install the antenna as follows:

1. Find a suitable location for mounting
the antenna vertically.

2. Power down the Control P
anel. Refer
to the PROLTE
Wireless
Communication Module Installation
Guide for Replacing the Module (P/N
800-
25165).

3. Remove the screw securing the
control panel
to the wall or desk
mount (if installed).

4. Remove the
control panel
from the
wall or desk mount (if installed).

5. Remove t
he screw retaining the
module (if installed).

6. Remove the PROLTE
module (if
installed).

7. Plug the MMCX end of the
PROLTE-
EXTCX
cable into the module’s
external antenna port and route the
cable as
shown in Figure 2.

8. Set the switc
h on the module to EXT.

9. Install the module in the panel and
secure with the screw.

10.
Route the SMA connector through
the back case and reinstall the front
case onto the back case.

11.
Connect
THE PROLTE-
EXTCX
cable

to the external antenna.

12.
Permanently mount the antenna
vertically
using the double-
sided self
-
adhesive and the included hardware.

12.
Reinstall the side cover.

13.
Install the control panel
onto the wall
or desk mount
.
14.
Reconnect the backup battery and
plug in the power supply.

15.
Install the rear cas
e and secure with
the screw.

16.
Per
form a Communication Test.

17 .



Figure 1 -
Remove the PROLTE
and Connect the Cable




Figure 2
–

PROA7
Series

External Antenna Installation






SPECIFICATIONS


Antenna

Type

Multiband, dipole


VSWR

<2:1

Bands

700, 850, 900, 1800, 1900,
& 2100 MHz


Dimensions / Weight

106 x 1
3 x 6.7mm /
40g

Polarization

Linear


Cover

PVC black

Gain (Average)

1
dBi

(average)


Cable Type / Length

RG
-
174 / 3m

Impedance

50 Ohms


Environmental

Waterproof IP67, -40°C to +85°C

Input Power (Max.)

5W


Connector Type

MMCX to

SMA


RF Exposure

Warning

– The internal or external antenna(s) used with this product must be i
nstalled to provide a separation di
stance of at least 7.8 in.
(20 cm) from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter except in
accordance with FCC multi
-transmitter product procedures.

Mise en
Garde

Exposition aux Fréquences Rad
io:
L'antenne (s) utilisée pour cet
émetteur doit être installée à
une distance de séparation d'au moins
7,8 pouces (20 cm) de toutes les personnes.



IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS

If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer.


TO THE INSTALLER

PROLTE
-A
The external antenna must not exceed a maximum directional gain (including cable loss) of 6.
63 dBi at 700 and
850 MHz, 6.0 dBi at 1700 MHz

and
8.51 dBi at
1900 MHz.
Under no
conditions may an antenna gain be used that would exceed the ERP and EIRP power limits as specified in
Part
s 22H and 24E and 27.


PROLTE
-V
The external antenna must not exceed a maximum directional gain (including cable
loss) of 6.
94 dBi at
700
MHz
6.0 dB
i at 1700 MHz at and
9.01

dBi at 1900 MHz. Under no conditions may an antenna gain be used that would exceed the ERP and EIRP power limits as specified
in Part
s 22H
and 24E and 27.


PROLTE
-CN
The external antenna gain sha
ll not exceed
6.63
dBi for 700MHz
and 850
MHz,
6.0
dBi for 1700MHz and 8.51
dBi for 1900MHz. Under no
conditions may an antenna gain be used that would exceed the ERP and EIRP power limits as specified
IC RSS
-130, RSS
-132, RSS
-133, and
RSS
-139
.


The produc
t should not be disposed of with ot
her household waste. Check for the nearest authorized collection centers or authorized recyclers.
The correct disposal of end-of
-life equipment will help prevent potential negative consequences for the environment and hum
an health.

Any attempt to reverse
-engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly pro
hibited
.

























































www.res
ideo.co
m

Resideo Technologies, Inc

2 Corporate Center Driv
e, Suite 100

P.O. Box 9040, Melville, NY 11747

© 2020 Resideo Technologies, Inc. All rights reserved.


The Honeywell Home trademark is used under license from
Honeywell Internat
ional, Inc.

This p
roduct
is manufactured by Resideo Technologies, Inc.
and its affiliates.


Ê800
-25607BeŠ

800
-
2
5607
B

6
/1
9

Rev
B