Honeywell Home PROSIXFOB Installation Instructions - Dated 2/19 Rev. B

PROSiXFOB

Wireless Key Fob

Installation
and Setup Guide

This bi
-directional wireless key fob (wireless key) is
intended for use with Honeywell
Home
controls that
support
PRO
SiX™ series devices.


Press and hold each button
about 2 seconds to
activate.

(For
two
-button
Pani
c, press and hold both
buttons for 2 seconds.)

ENROLL AND PROGRA
M THE PROSIXFOB

BUTTON KEYS 1
-8
(Corresponding
services
are seen
when programming
the key fob
through the p
rogramming menu.)

*SIA NOTE
: SIA requires 2-
button press for
panic
functions.


Set the
control
in Programming mode, when prompted:

1. Press
and
hold the
top
two
buttons
for about two seconds
to activate
the
enrollment process
.
2.
The
LED
s alternately
flash
green
during enrollment
(up to
about
20 seconds
). The device sends
its unique MAC ID
and Services information to the controller.

NOTE
: Enrollment time varies depending on the signal strength between the device and the controller.

3. The LEDs light solid green for 3 seconds and the PROSiXFOB
emits a chirp
to confirm enrollment
.
NOTE
: If enr
ollment is not confirmed, press and hold the top two buttons for two seconds again to restart the
enrollment process.

4. Use
program menu to change default key functions as desired.

5. Assign a User Number to the key fob.

Follow instructions in
the Control
ler
’s programming guide to program the
PROSiXFOB
services.

After enrolling, update the PROSiXFOB
firmware
(via the Controller) to ensure the latest version is used. See the
Controller’s instructions.

You must enroll the device in the control.
Re
fer to the cont
rol's programming instruction for detailed procedures.


NOTE
: Once enrolled in a system, the PROSiXFOB
cannot be used with another controller until it is removed
from the current
controller. When removed from a system, the key fob will
r
ev
e
rt to factory
de
fault settings.

BATTERY REPLACEMENT

When the battery is low, the LEDs do not flash during transmission. To replace the battery:

1. Remove the screw from the back housing and use a screwdriver to gently separate the front and back housings
.
2. Use a screwdriv
er to carefully remove the battery.

3. Wait 10 seconds or press a key fob button for 2 seconds to ensure full power discharge.

4. Insert a new Lithium, 3V,
210mAh
battery as shown. Recommended replacement battery:

Maxell CR2032 or
Duracell D
L20
32

5. Replace the
front housing and secure the housings with the cover screw.


BATTERY CAUTION
: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212°
F (100
°C) or
incinerate. Dispose of used batteries properly. Keep away from chi
ldren.



SYSTEM STATUS AND SOUNDER INDICATIONS

The
PROSiXFOB
can be used to control the system (e.g., arm, disarm the system); and receive system status
information (armed status, not ready to arm, in alarm, in RF transmission mode, and more). Press
and release any
b
ut
ton and observe the key fob. R
efer to the table
below
for
system status information
.

System Status Indications

G

R


System Status




Device Enrollment




System is Armed




Alarm in progress or System in Audible Panic
Mode



Disarmed, Ready to Arm




Disarmed, Not Ready to Arm




RF Transmission




Not Hearing from the Controller



Deleting the Keyfob from the system





SPECIFICATIONS:

Battery
: Lithium, 3V,
210mAh;
Maxell
CR2032,
Duracell
DL2032

RF Fre
que
ncy
: 2.4GHz

Ope
rating Temperature
: 0° to 50° C / 32° to 122° F

(Agency compliance 0° to 49° C / 32° to 120° F)

Relative Humidity
: 95%
max.
(Agency compliance –
93%
max.
),
non
-condensing

Dimensions
: 11 mm H x 65.5 mm L x 36 mm W
/ 0.43” H x 2
.58” L x 1.42”
W
APPROVAL LISTINGS:

FCC / IC
cETL
us Listed

Conforms
to UL
1023 & UL
985
Certified to ULC ORD-
C1023

& ULC-S545
Other Standards:

SIA CP-01 RoHS
C
-Tick

Product must be tested at least once each
year.


IMPORTANT!
This wire
les
s key is intended
as a convenience to the user and should not be considered as a life safety device.





IMPORTANT SECURITY NOTICE

Please inform the User about the security importance of their wireless key (key fob), and what to do if it is lost.

Explain
that the key fob i
s similar to their keys or access card. If lost or stolen, another person can compromise their security system.
They should immediately notify the Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then remove the key
fob
programming f
rom the security system.




FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or U
ser's Manu
al.
Unauthorized c
hanges or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following st
ate
ment for your
information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordanc
e with the manufacturer's
instructions, may cause interference to radio and television reception. It has
been type test
ed and found to comply with the limits for a Class B
computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable prot
ection against such
interference in a residential installati
on.
However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged t
o try to correc
t
the interference by one or more of the following measures:

•
If using an indoor antenna, replace it with a quality outdoor antenna.

•
Reorient the receiving antenna until interference is reduced or eliminated.

•
Move the radio or tel
evi
sion receiver awa
y from the receiver/control.

•
Move the antenna leads away from any wire runs to the receiver/control.

•
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch cir
cuit
s.
•
Consult the
dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.

Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.

FCC
/ IC STATEMENT

Thi
s device complies with Part 15 of the FCC Rules, and Industry Canada’s license-
exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interfe
rence received,
including interference that may cause
undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement
est soumis aux
conditions suivantes: (1) Cet apparei
l ne doit pas caus
er d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les
interférences causant une réception indésirable.


RF
EXPOSURE

Warning
– The antenna(s) used for this device must not be co-located or oper
ati ng in conjunction with any other antenna or transmitter
except in accordance with
FCC multi
-transmitter product procedures.

MISE EN GARDE EXPOSITION AUX FREQUENCES RADIO

Attention
– L'antenne (s) utilisé pour cet appareil ne doit pas être co-localisées
ou
opérant conjointement avec une autre antenne ou
émetteur non conformant avec les
procédures FCC poules produits à multi
-transmetteurs
.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATI
ONS

OF THE ENTIRE
ALARM SYSTEM.













































Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-
577-
2000


The product should not be disposed of with other hous
ehold waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-
of-life equipment will help prevent potential negative consequences for the
environment and human health.

Any attempt to reverse-
engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly prohibited.


SUPPOR
T & WARRANTY INFORMATION

For the latest documentation
and
support, pl
eas
e go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty



The Honeywell Home Trademark
is used under license from Honeywell International Inc.

This product is manufactured by Resideo
Technologies
, Inc.
and its affiliates
.

2 Corpora
te Center Drive,
Suite 100
P.O. Box 9040, Melville, NY 11747

2020
Resideo Technologies, Inc.

www.r
esideo.com





Ê800
-25221B#Š

800
-25221
B 2/19
Rev
B