Honeywell Home PROSIXSIREN Installation Instructions - Dated 2/19 Rev. B

PR
O
SiXSIREN

Wireless Siren/Strobe

Installation
and
Setup Guide



This wireless siren/strobe is intended for use with Honeywell Home
controls that support
PRO
SiX™ series devices.


PRO
SiXSIREN


OPEN

Gently twist the top of the Siren counterclockwise and the mounting bracket clockwise to separate them
.


MOUNTING

The
PR
OSiXSIREN can be mounted on the wall or on the ceiling.

The rear tamper breakout [
A
] MUST be mounted to a stud, solid wood, or with a robust wall anchor.

After enrolling, verify adequate signal strength by conducting sensor test
(see controller’s instruc
tions) with the
device in its intended mounting location. Adjust the device location and orientation as necessary.


ENROLL

This device can be enrolled and programmed
either before or after installation.

Set the control
in Programming Mode and
when
prompted

1. Ins
ert four
1.5V
AA Lithium
batter
ies
(included)
to
activate the device and be
gin the enrollment
process.

2. The
Green
LED flashes rapidly
during enrollment
(up to
about
20 seconds
*)
*NOTE
: Enrollment time varies depending on the
signal strength betw
een the
device and the
controller
.

•
The device sends its unique MAC ID address
(Serial
Number) and Services information to
the
control
ler .
•
The control
ler
registers the device and
displays the transmitter data on screen.

3. Enrollment is confirmed when t
he
Green
LED
is
ON for 3 seconds
.
4. The device did not enroll in the system
if:
•
The
White LE
D flashes, the system chirps and
the device powers down.

•
The
Green LED flashes rapidly when the
device is removed from the mounting bracket

(the tamper switch is trigger
ed)
.
To
restart the enrollment process, ensure the system
is in programming mode and activate the tamper
switch.


The device can also be manually enrolled. See the Controller’s
Programming Guide for details.

NOTE
: Once enrolled in a system, the device
cannot
be used
with another controller until it is removed from the current
controller
. See the Controller’s instructions for details.


PROGRAM

See
the Controller’s instructions for programming the device in the system.
Refer to the LED and Sounder tabl
e for details of chime operation when the CHIME feature is enabled (factory
default is
enabled).

DEFAULT PROSIXSIREN

If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended
panel, default
the device:

1. Open the cover and remove the batteries.

2. Hold down the tamper switch whil
e reinserting the batteries.

3.
Reattach the cover.


This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery insta
ll
ed).


LEDS AND SOUNDER

Refer to the table below for operation of the
four bi
-col
ored LEDs and an 85dB sounder.


R / W

G / W

Sounder

Status




Green Rapid Flashes
for about 20 seconds,
then ON for 3 seconds

once

Power Up –
Enrollment




Green Slow Flas
hing
for 3 seconds
once

Power Up –
Device enrolled




Green ON for 20
sec
onds


System is Disarmed


Red ON for 20 seconds




System is Armed


Alternating Red and
White Strobe Flash
1

(continues until the Alarm
is cleared)




Smoke / Heat Alarm




CO Alarm


White ON


White ON


3 seconds

Burglary Alarm


Red flashes o
nce

every 45 seconds




2

Low Battery




Green Flashes slowly
for 10 minutes


Tamper Activated







Chime operation when the CHIME feature is enabled

x 1

The s
ystem
is Di
sarmed
x 2

The system is Armed, Away mode

x 3

The system is Armed, St
ay mode

or a Zone was Faulted


1
Strobe flash = two flashes per second, then OFF for 1 second.

2
After 7 days, the sounder
chirp
s once every 45 seconds
until
the
bat
terie
s are replaced or die. See the Battery Replacement section.

TEST THE PROSIXSIREN

The
PRO
SiX
SIREN
should be tested
immediately
after installation and weekly.
Activate Test Mode remotely from the
Controller (see Controller’s manual for details).

Th
e pro
duc
t must be tested at least o
nce a
year
.

Test Mode tests the sounder and LED
:
•
Sou
nder
– the
Burglary warble tone will sound for 3 seconds.

•
LED
– the W
hite LED
strobe
will
flash for
15 seconds.


BATTERY REPLACEMENT

•

Twist the front cover counterclockwis
e and separate it from the
mounting bracket.

•

Remove the batteries, wait 10 seconds
and
insert four new
batteries

of the same type and brand
.
Recommended replacement batteries:

-
1.5V AA Lithium Batteries [Non-
Rechargeable]

-
AA Alkaline batteries can
be us
ed, but battery life will be
significantly reduced.

NOTE
:
Do not mix old and new b
atteries, battery types or
manufacturers.

•

Reattach the front cover and twist clockwise to secure it in place.

BATTERY CAUTION
: Risk of fire, explosion and burns. Do not re
charge, disassemble,
heat above 212
F (100
C) or incinerate. Dispose of used batter
ies properly. Keep away
from children.

NOTE
: Constant exposure to high or low temperature or high humidity may reduce
battery life
.


SPECIFICATIONS:

Range
: 300 feet
nomi
nal in
doors (actual range determined by the system in TEST mode)

Battery
: Four
1.5
V,
AA
Lithium
, Non
-Rechargeable;
Energizer E
2
,

Resideo
462

Tamper
: Cover
and Wall
tamper

RF Frequency
: 2.4GHz

Input Voltage
: 3,3VDC

Current
: 339 mA, Typical

Siren Outpu
t Lev
el
: 85
dB at 10 feet

Operating Temperature
:
0° to
50°C / 32° to
122
°F
(Agency Com
pliance
0° to 49°C
/ 32° to 120°F
)
Relative Humidity
: 95%
max. (Agency compliance –
93% max)
, non-condensing

Dimensions
: 14.14 cm Diameter x 4.62
cm Thick / 5.
5 in. Dia
meter
x 1.8 in. Thick

APPROVAL LISTINGS:

FCC / IC
cETL
us Listed

Conforms
to UL
985
/
UL
1023

Certified
to ULC
-S545 &


ULC/ORD-C1023

Other Standards:

RoHS


FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall n
ot mak
e any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This
equipment has been tested and found to comply with the limits for a Class B digi
tal device, as defined by FCC Rules Part 15.105. The Class B Digital Device
statement can be viewed at:

https://customer.resideo.com/en-
US
/support/residential/codes
-and-
standards/FCC15105/Pages/default.aspx


FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada’s licens
e-exe
mpt RS
Ss. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation.

Cet appareil est conforme à
la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Cana
da. Son fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y
compris les interférences causant une réception
indésirable.


RF
EXPOSURE

Warning
– The antenna(s) used for this device must be installed to
provide a separation distance of at least 7.8 inches (20 cm)
from all persons and must not be co-located or operati
ng in conjunction with any other antenna or transmitter except in accordance
with FCC and ISED multi
-transmitter product procedures.

MISE EN
GARDE

Exposition aux Fréquences

Radio :
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être ins
tallée
(s) à une distance de
séparation d'au moins 20 cm (7,8
pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tou
t autre
transmetteur ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED
.

REFER TO THE INSTALLATION INSTRUC
TIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS
REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo
Technologies, Inc., 2 Corporate Center
Drive., Melville, NY 11747, Ph: 516-
577-
2000


The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and human health.

Any attempt to reverse-
engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly prohibi
ted.


SUPPOR
T & WARRANTY INFORMATION

For the latest documentation
and
support, please go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty

The H
oneywell Home Trademark
is used under license from Honeywell International Inc.

This product is manufactured by Resideo
Technologies, Inc.
and its affiliates.


2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville,
NY 11
747


2020
Resideo Technologies, Inc.
www.resi
deo.com


Ê800
-
25229BkŠ

800
-25229
B 2/19 Rev
B