Honeywell IPCAM-WIC2 - Quick Install Guide

800-23609
9/17 Rev. A
Google Play and the Google Play logo are trademarks of Google Inc.


IPCAM
-WIC
2 HD Wi
-Fi Indoor Video Camera

Quick Installation Guide

IPCAM
-WIC2 is a 1080p, full HD Wi
-Fi video camera intended for indoor use with Honeywell Total Connect® 2.0.

Low
-light operation is indicated by four red LEDs located on the front of the camera
, arranged around
the lens.

Camera setup requires a Total Connect® 2.0 account and the new Total Connect 2.0 mobile app.
Video Services must
be enabled in AlarmNet 360™.
Camera operation requires minimum available bandwidth of 2.1 Mbps.



For best results, set up only one camera at a time.
Download the Total Connect® 2.0 app from
the App Store or on
Google Play.

(Look for the
red
Total Connect
logo
.)



a.

Turn on your

smart device’s Bluetooth and Wi
-
Fi
.

[
Make

sure
the
Bluetooth isn’t connected to another device
and that

you’re
on
the same Wi
-Fi
network your camera(s) will use .
]

b.

Launch the app and sign in with your Total Connect® 2.0
account.

c.

Plug
the power
supply in
to an AC outlet,
but:
.
Don’t
connect
the power supply to the camera yet.

Note
that the screens in your app may be a bit different than the
examples seen here.




If your account has more than one
Location
, select the one where
you’re doing camera setup.
You may have to press
CAMERAS

at the bottom of the screen
to
see
the Cameras page.

a.

Press
ADD CAMERA

b.

Select the type
of camera you’re installing
.
c.

Name
the
camera
and
press

NEXT
.
d.

Connect the power supply to the camera. The
LED
at the top flashes
a variety of colors.
After about a minute, the camera sounds a tone.
Then,
WAIT
for the camera’s LED to flash blue
only
.
e.

Press
NEXT
on the app.




a.

On the
Pair Your Camera
screen, press
Generate
QR
Code
. After
a brief wait
, the code appears
.
b.

Show the QR code on your device to the camera from 3
– 8 inches

away.
You will be notified when the code has
been
successfully

scanned
.
c.

Select
your
security
system
’s Wi
-Fi network and press

NEXT
.
d.

Enter the network password and press

NEXT
. Final setup begins.


When
the app displays
Setup Successful
, the process is
complete
*.
Press
DONE
or
ADD ANOTHER CAMERA
.




After setup, go back to the
CAMERAS
page
and check your
newly
-registered
camera.

Touch the
preview
image
to launch a live stream from the camera.

*The app will tell you if you need to repeat the setup process
. This
involves resetting the camera
, which is described in the
app itself
.
See the other side of thi
s sheet for more
information about the
required steps.


Resetting the Camera

If Wi
-Fi fails, or to
connect
the camera to a different
network,
activate
the Reset switch
with a paper clip.

•

To reset the connection,
press
and hold for 1
5 seconds

•

To join a new/different
network
:
o

On the app’s
Cameras
screen, press
and delete the camera from
the
link on
its

settings
page
.
o

Press and hold the
Reset
switch
for 15
seconds to reset all set
tings to their factory defaults

o

Unplug the camera and then reconnect it.

o

Repeat the registration procedure.





LED STATUS INDICATOR

During installation


Blue, blinking

Power on. Ready to start setup.


Blue, steady

Connected to the app. Ready to complete setup.


Purple, steady

QR code scan is complete. Restart the Wi
-Fi connection process.


Green, blinking

Connecting to Wi
-Fi network.


Red, steady

Setup timed out. Unplug the camera, plug it back in and restart setup process.

During operation



Green, blinking

Connecting to
Wi
-Fi network.


Green, steady

Connected to Wi
-
Fi and operating.
Note
: The camera is always ready to record but only
originates live streaming video when the app calls for a live stream.


Red, blinking

Not connected to Wi
-
Fi.


Low
-
light operation is ind
icated by
four

red LEDs
arranged

around

the
lens

on the front of the camera
.

FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make
any changes or modifications to the equipment
unless
authorized by the
Installation Instructions or User's
Manual.
Unauthorized changes or modifications could
void the user's
authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable fo
r use. The FCC requires the following
statement for your
information:

This equipment
generates and uses radio frequency
energy and if not installed and used
properly, that
is, in strict accordance with the
manufacturer's instructions, may cause interferenc
e to radio and television
reception. It has been type tested and found to comply
with the limits
for a Class B computing
device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide
reasonable
protection against
such
interference in a residential installation. However, there
is no guarantee
that
interference
will not occur in a particular
installation. If this
equipment
does cause interference to radio or television
reception, which
can
be
determined by turning the equ
ipment off and
on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

•

If using an indoor antenna, have a quality
outdoor
antenna
installed.

•

Reorient the receiving
antenna
until
interference
is reduced or
eliminated.
•

Move the radio or television
receiver
away
from the receiver/control.

•

Move the antenna leads away
from
any
wire
runs to the receiver/control.

•

Plug the receiver/control into a different
outlet
so
that
it and the radio or television
receiver are on different
branch circuits.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry
Canada’s
license-
exempt RSSs.
Operation
is subject to the following
two
conditions: (1) This device
may not cause harmfu
l interference, and (2) This device must accept
any
interference
received, including
interference

that
may cause undesired
operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de
licence RSS d’Industrie Canada. Son fonctionnement est soumis aux
conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute int
erférence reçue y
compris les interférences causant une réceptio
n indésirable.
RF EXPOSURE STATEMENT
:
The antenna(s) used for this
device must be installed
to provide a separation distance of at least 7.8 inches (20 cm)
from all persons and must not be
co
-located or operating in conjunction
with
any
other
antenna or tr
ansmitter
except in accordance with FCC
multi
-transmitter
product
procedures.

MISE EN GARDE EXPOSITION AUX FR
ÉQUENCES RADIO
: L'antenne (s) utilisée pour cet
émetteur
doit
être
installée à une distance de
séparation
d'au
moins 7,8 pouces (20 cm) de toutes
les personnes.


DECLARACIÓN IFETEL

La operación de este equipo
está
sujeta a las siguientes dos condiciones

1.

Es
posible que este equipo o dispositivo no cause interferencia
perjudicial y

2.

Este equipo
debe
aceptar
cualquier
interferencia, incluyendo la
que pueda
causar

su
operación no deseada.

DECLARACIÓN ANATEL

Este equipamento opera emcarátersecundário, isto é, nãotemdireito a
proteção contra interferência prejudicial, mesmo de estações do
mesmotipo, e nãopodecausarinterferência a sistemas operando
emcaráterprimário.





TRADEMARKS

Honeywell is a registered trademark
of Honeywell International Inc.


For online support visit
, https://mywebtech.honeywell.com/

For the latest warranty information, visit
http://www.security.honeywell.com/hsc/resources/wa/


‡800
-
23609KŠ

800
-23609
9/17
Rev. A


2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747


2017
Honeywell International Inc.

www.honeywell.com/security