Honeywell Vista-15P/Vista-20P - Program Guide - Dated 3/15 Rev. B
Related Products
Related Categories
Document Transcript
A
A
D
D
E
E
M
M
C
C
O
O
V
V
I
I
S
S
T
T
A
A
S
S
E
E
R
R
I
I
E
E
S
S
V
V
I
I
S
S
T
T
A
A
-
-
1
1
5
5
P
P
V
V
I
I
S
S
T
T
A
A
-
-
1
1
5
5
P
P
S
S
I
I
A
A
V
V
I
I
S
S
T
T
A
A
-
-
2
2
0
0
P
P
V
V
I
I
S
S
T
T
A
A
-
-
2
2
0
0
P
P
S
S
I
I
A
A
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
G
G
u
u
i
i
d
d
e
e
K5305-
1PRV9
3/15 Rev
B
RECOMMENDATIONS FOR PROPER PROTECTION
The Following Recom
mendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for
the Protected Premises
.
Recommendations for Smoke and Heat Detectors
Regarding the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National
Fire Protection Association's (NFPA) Standard #72 noted below.
•
Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household
as follows: For minimum
protection, a smoke detector should be installed outside of each separate sleeping area, and on each
additional floor of a multi
-floor family living unit, including basements. The installation of smoke detectors
in kitchens, attics (finished
or unfinished)
, or in garages is not normally recommended.
•
For additional protection, the NFPA recommends that you install
heat
or
smoke detectors
in the living room, dining room,
bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basement
s and attached garages
.
In addition, we recommend the following
•
Install a smoke detector inside every bedroom where a smoker sleeps.
•
Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be
blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed.
•
Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are
used.
•
Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.
•
Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an A
C
source or phone lines
are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire
or an intrusion
THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE
SOUNDING OF FIRE NOTIFICATION APPLIANCES.
Recommendations
for Proper Intrusion Protection
•
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. T
his
would include any skylights that may be present, and the upper windows in a multi
-level buildi
ng.
•
In addition, we recommend that a communications backup be used in the security system so that alarm signals can still be sent
to
the Central Moni
toring Station if
communications are out of order (alarm signals are normally sent over the cellular and/or
Wi
-
Fi/internet networks).
This security system is designed for use with devices manufactured or approved by Resideo Technologies, Inc., through
its subsidiary Ademco Inc. (“Resideo”), for use with your security system. Your security system is not designed for use
with any device that may be attached to your security system's keypad or other communicating bus if Resideo has not
approved such device for use with your security system. Use of any such unauthorized device may cause damage or
compromise the per
formance of your security system and affect the validity of your Resideo limited warranty. When you
purchase devices that have been manufactured or approved by Resideo you acquire the assurance that these devices
have been thoroughly tested to ensure optim
um performance when used with your security system
.
i
Table of
Contents
Programming Mode Commands
.............................................................................................................................
1
Data Field Programming
..........................................................................................................................................
2
Configurable Zone Type Worksheet
.....................................................................................................................
18
∗
56 Zone Programming Menu Mode
....................................................................................................................
19
∗
58 Expert Zone Programming Menu Mode
........................................................................................................
22
Wireless Key Templates
........................................................................................................................................
23
∗
57 Function Key Menu Mode
...............................................................................................................................
25
Output Device Programming General Info (*79/*
80 Menu Mode)
......................................................................
26
*79 Relay/X
-10 Menu Mode
....................................................................................................................................
26
∗
80 Output Function Menu Mode
.........................................................................................................................
28
∗
81 Zone List Menu Mode
.....................................................................................................................................
30
∗
82 Alpha Descriptor Menu Mode
.........................................................................................................................
31
Scheduling Menu Mode
.........................................................................................................................................
34
Setting the Time Clock
..........................................................................................................................................
35
∗
29 Communicator Menu Mode
............................................................................................................................
36
Uploading/Downloading via the Internet
.............................................................................................................
38
Zone Type Definitions
............................................................................................................................................
39
Report Code Formats
............................................................................................................................................
40
System Security Codes
.........................................................................................................................................
41
Keypad Functions
..................................................................................................................................................
42
Worksheet for
∗
56 Zone Programming
................................................................................................................
43
Worksheet for
∗
57 Function Key Programming
..................................................................................................
45
Worksheet for
∗
79 Output Relay/X
-10 Programming
..........................................................................................
46
Worksheet
for
∗
81 Zone List Programming
.........................................................................................................
46
Worksheet for
∗
80 Output Function Programming
.............................................................................................
47
Worksheet for Schedules
......................................................................................................................................
49
Table of Device Addresses
....................................................................................................................................
50
Compatible Devices
...............................................................................................................................................
51
Agency Regulatory Statements
............................................................................................................................
52
SIA Quick Reference Guide
...................................................................................................................................
53
FCC Statements
.....................................................................................................................................................
54
Limitations Statement
............................................................................................................................................
55
Contacting Technical Support
..............................................................................................................................
56
5800 Series Transmitter Input Loop Identification
..............................................................................................
57
VISTA-
15P/20P/SIA Program
Guide
ii
VISTA-
15P/20P/SIA Program
Guide
1
Programming Mode Commands
Compatibility: This document applies to systems with microprocessor version
9.12
or higher.
TO ENTER PROGRAMMING MODE
(using an alpha keypad connected to the control)
:
A.
POWER UP, then press [
Q
] and [#] at
the same time, within 50 seconds of powering up (this method must be used if
Q
98 was used to exit program mode).
OR
B.
Enter
Installer Code
(4112)
then
8 0 0
.
PROGRAMMING COMMANDS
Task
Command/Explanation
Go to a Data Field
Press [
∗
] + [Fi
eld Number], followed by the required entry.
Entering Data
When the desired field number appears, simply make the required entry. When the last entry
for a field is entered, the keypad beeps three times and automatically displays the next data
field in sequence. If the number of digits that you need to enter in a data field is less than the
maximum digits available (for example, the phone number fields *41, *42), enter the desired
data, then press [
∗
] to end the entry. The next data field number is displa
yed.
Review a Data Field
Press [#] + [Field Number].
Data will be displayed for that field number. No changes will be accepted in this mode.
Deleting an Entry
Press [
∗
] + [Field Number] + [
∗
].
(Applies only to fields
∗
40 thru *46, *94, and pager fields)
Initialize Download ID
Press
∗
96.
Initializes download ID and subscriber account number.
Reset Factory Defaults
Press
∗
97.
Sets all data fields to original factory default values.
Zone Programming
Press
∗
56.
Zone characteristics, report codes, alpha de
scriptors, and serial numbers for
5800 RF transmitters.
Function Key Programming
Press
∗
57.
Unlabeled keypad keys (known as ABCD keys) for special functions
Zone Programming
(Expert Mode)
Press
∗
58.
Same options as *56 mode, but with fewer prompts. Inten
ded for those familiar
with this type of programming, otherwise *56 mode is recommended.
Output Device Mapping
Press
∗
79.
Assign module addresses and map individual relays/powerline carrier devices
Output Programming
Press
∗
80.
4229 or 4204 Relay modules
, Powerline Carrier devices, or on
-
board triggers
Zone List Programming
Press
∗
81.
Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.
Alpha Programming
Press
∗
82.
Zone alpha descriptors
IP/
Cell
Programming
Press
∗
29.
Fo
r programming the IP/
Cell
options.
Exit Program Mode with
installer code lockout
Press
∗
98.
Exits programming mode and
prevents
re
-
entry by: Installer Code + 8 0 0.
To reenter programming mode, the system must be powered down, then powered up. Then
use method A above. See field *88 for other *98 Program mode lockout options.
Exit Program Mode
Press
∗
99.
Exits program
mode and
allows
re
-
entry by:
Installer Code + 8 0 0
or method A
above.
Scheduling Mode
Enter code + [#] + 64.
Create schedules to aut
omate various system functions.
Site
-
Initiated Download
Installer code + [#] + 1
(perform while system is disarmed
and in normal mode
)
USING
REMOTE SERVICES
This
control supports
Remote Interactive Services (RIS)
such as Total Connect 2.0, Tuxedo/Z
-Wave scenes
, and
Home Automation (Control 4, 4232CBM
), if supported by
the communication service in use.
•
Remote Interactive Services
is automatically enabled in
the control
; device address 25 is automatically
assigned.
•
Use programming field
∗
189 to enable a remote services
emulated keypad address.
•
Use
∗
29 Menu mode to enable the communication
device.
•
If using Total Connect 2.0,
use AlarmNet Direct
to
program
the
device
and enable TC2 services. Be sure to
“send”
the programming data
to the Communicator.
IMPORTANT:
The Real
-Time Clock
must be set before
the end of the installation. See procedure in the Setting
the Real
-Time Clock section of this manual.
SPECIAL PROGRAMMING MESSAGES
•
OC
= OPEN CIRCUIT (no com
munication between
Keypad and Control).
•
EE
or
ENTRY ERROR
= ERROR (invalid field number
entered;
re-enter valid field number).
•
After powering up,
AC, dI
(disabled) or
“
Busy Standby
vx.x
(firmware revision)
Dl
will be displayed after
approximately 4 seconds. This will revert to a “
Ready
”
message in approximately 1 minute, which allows PIRS,
etc. to stabilize.
You can bypass this delay by pressing
[#] + [0].
NOTE for CANADIAN PANELS:
Power up time is 2
minutes, and Contact ID report code 305 System Reset
is sent if the [#] + [0]
command is not performed before
the 2 minutes expires.
•
If
E4
or
E8
appears, more zones than the expansion
units can handle have been programmed. The display
will clear after you correct the programming.
VISTA-
15P/20P/SIA Program
Guide
2
Data Field Programming
Entries apply to the ADEMCO VISTA
-15P/VISTA-
15PSIA and ADEMCO VISTA-
20P/VISTA-
20PSIA controls, except entries
shown in dashed boxes, which apply only to the VISTA
-20P/VISTA-
20PSIA (partition entries) and are not applicable
to the
VISTA-
15P/VISTA-
15PSIA. In addition, where noted, certain fields have special settings when used with the
SIA panels
(indicated by
V20PSIA/V15PSIA
with heavy borders and reverse type throughout for easy identification).
Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.
SIA Guidelines:
Notes in certain fields give instructions for programming the VISTA
-20P/VISTA-
15P for False Alarm
Reduction.
SIA Installations:
The VISTA-
20PS
IA and VISTA-
15PSIA are certified SIA
-compliant controls that meet SIA specifications
for False Alarm Reduction. The other controls described in this manual are not certified as SIA compliant, but can be
programmed for False Alarm Reduction. To program for
False Alarm Reduction, follow the SIA Guidelines noted in the
applicable programming fields.
∗
20
Installer Code
Enter 4 digits, 0000-
9999
| | |
[4112]
The Installer Code is used to assign the 4-
digit Master Security Code.
The I
nstaller Code can perform all system functions except it cannot
disar
m the system unless it was used to arm the system.
For security
purposes, the factory default installer code should be changed.
∗
21
Quick Arm Enable
0 = no
1 = yes
[0,0]
Part. 1
Part.2
If enabled, users can press the [#] followed by an arming key to arm
the system instead of using a security code. The security code is
always needed to disarm the system.
∗
22
RF Jam Option
0 = no RF Jam detection
1 = send RF
Jam report
[0]
If enabled, a report is sent if the system detects an RF jamming signal.
UL:
must
be
1
if
wireless
devices
are
used
∗
23
Quick (Forced) Bypass
0 = no quick bypass
1 = allow quick bypass (code + [6] + [#] )
[0,0]
Part. 1
Part. 2
Zones bypassed by this function will be displayed after the bypass is
initiated.
UL:
must
be
0
∗
24
RF House ID Code
00 = disable all wireless keypad use
01–
31 = using 5827
or 5804BD keypad
|
|
|
[00,00,00]
P1
P2
Common
The House ID identifies receivers and wireless keypads. If a 5827
or
5804BD Transmitter is being used, a House ID code
must
be entered
and the keypad set to the same House ID.
You can assign RF house
ID for each partition
∗
26
Chime By Zone /
KP Sound Enables
Entry 1
no “entry 1”
keypad trouble sounds
,
AND no chime by zone
(keypad chimes
on fault of any entry/exit or perimeter
zone when chime mode is on)
Chime by Z
one enabled
Communication
Device
(LRR)
trouble
sounding
enabled
for
an Alarmnet
communicat
or.
System Low Battery sounding enabled
select all entry 1 options
Entry 2
no
“entry 2
” keypad trouble
sounds
RF Supervision sounding enabled
RF Low Battery sounding enabled
RF Jam sounding enabled
select all entry 2 options
[6, 7]
1
2
Chime by Zone
If Chime by Zone is enabled (entry 1
– option 1), you c
an define the
specific zones intended to chime when faulted while the system is in
Chime mode.
List chime zones on zone list 3 using *81 Menu mode.
Keypad
(KP)
Trouble Sounding
Keypad trouble sounding can be enabled/disabled for the conditions
listed for
each entry.
For each entry, enter the sum of the desired options. Example Entry 1:
for Chime by Zone and System Low Battery sounding, enter 5. To
enable all options, enter 7.
VISTA-
15P/20P/SIA
Program
Guide
3
Data Field Programming
(Continued)
∗
27
Powerline Carrier Device (X
–
10
)
House Code
0 = A
6 = G
#11 = L
1 = B
7 = H
#12 = M
2 = C
8 = I
#13 = N
3 = D
9 = J
#14 = O
4 = E
#10 = K
#15 = P
5
= F
[0]
Powerline Carrier devices require a House ID, identified in this field.
Program Powerline Carrier devices in interactive modes
∗
79, *80 and
*81.
UL:
not
for
fire
or UL
installations
∗
28
Access Code
f
or Phone Module
00 = disable
1st digit: enter 1–
9
2nd digit: enter # + 11 for "
∗
", or # + 12
for "#".
|
[00]
(Partition 1 only)
You must ass
ign a 2-
digit access code for the 4286 Phone Module, if
used. Example: If desired access code is 7
∗
, then 7 is the first entry,
and [#] + 11 (for
∗
) is the second entry.
NOTE:
A 0 in either digit disables the phone module.
UL:
must
be
00
for
UL
Commercial
Burg.
installations
∗
29
Enable IP/GSM
? – Communication Device Menu Mode (pass
-through programming)
This is a Menu Mode command, not a data field, for programming IP/
Cell
communication device options. See
∗
29 Menu
Mode section later in this document.
∗
31
Single Alarm Sounding Per Zone
0 = unlimited sounding
1 = one alarm sounding per zone
V20PSIA/V15PSIA:
If “0” selected,
“alarm sounding per zone” will be the
same as the “number of reports in
armed period” set in field *93 (1 if
one report, 2 if
2 reports, unlimited
for zones in zone list 7).
[0]
If enabled, limits alarm sounding
on the bell
output to
once per zone
per armed period.
∗
32
Fire Alarm Sounder Timeout
0 = sound stops at timeout selected in
field
∗
33
1 = no timeout;
sounds until manually
turned off
[0]
This control complies with NFPA requirements for temporal pulse
sounding of fire notification appliances. Temporal pulse sounding for a
fire alarm consists of the following:
3 pulses
– pause
– 3 pulses
– pause
–
3
pulses.
UL:
must
be
1 for
fire
installations
∗
33
Alarm Sounder (Bell) Timeout
0 = none
3 =
12 min
1 = 4 min
4 = 16 min
2 = 8 min
[1]
This field determines whether the external sounder
(and keypad
sounder)
will shut off
after time allotted, or continue until manually
turned off.
UL: For residential fire alarm installation, must be set for a minimum of 4 min
(option 1); for UL Commercial Burglary installations, must be minimum 16
min (option 4)
∗
34
Exit Delay
00
- 96 = 0
- 96 secs
97 = 120 secs
V20PSIA/V15PSIA:
45
- 96 = 45
- 96 secs; 97 = 120 secs
NOTE: Entries less than 45 will result
in a 45-
second delay.
|
|
[60,60]
Part. 1
Part. 2
The system waits the time entered before armi
ng entry/exit zones. If
the entry/exit door is left open after this time expires, an alarm will
occur. Common zones use same delay as partition 1.
SIA Guidelines: minimum exit delay is 45 seconds
Common zones use part. 1 delay.
UL installations: For UL Com
mercial Burglar Alarm and UL Residential
Burglar Alarm installations with line security, total exit time must not exceed
60 seconds.
VISTA-
15P/20P/SIA Program
Guide
4
Data Field Programming
(Continued)
∗
35
Entry Delay #1
00
- 96 = 0
- 96 seconds
97 = 120 secs
98 = 180 secs
99 = 240 secs
V20PSIA/V15PSIA:
30-
96 = 30
- 96 secs; 97 = 120 secs;
98 = 180 secs; 99 = 240 secs
NOTE: Entries less than 30 will result
in a 30-
second delay.
|
|
[30,30]
Part. 1
Part. 2
Upon entering, the system must be dis
armed before the time entered
expires, otherwise it sounds an alarm.
Common zones use same delay as part 1.
SIA Guidelines: minimum entry delay is 30 seconds
For UL Residential Burglary Alarm installations, must be set for a maximum
of 30 seconds; entry delay plus dial delay should not exceed 1 min. For UL
Commercial Burglar Alarm, total entry delay may not exceed 45 seconds.
Upon entering, the system must be disarmed before the time entered
expires, otherwise it sounds an alarm.
∗
36
Entry Delay #2
Se
e *35 Entry Delay 1 for entries.
|
|
[30,30]
Part. 1
Part. 2
∗
37
Audible Exit Warning
0 = no; 1 = yes
V20PSIA/V15PSIA:
Feature
always
enabled; field does not exist.
[1,1]
Part. 1
Part. 2
Wa
rning sound consists of slow continuous beeps until the last 10
seconds, and then it changes to fast beeps. Sound ends when exit
time expires.
SIA Guidelines: must be enabled
∗
38
Confirmation
o
f Arming Ding
0 = no
1 = yes (wired keypads and RF)
2 = yes, RF only (except 5827)
[0,0]
Part. 1
Part. 2
Confirmation of arming is 1/2-
sec external sounder “ding.”
If 1 selected, ding occurs when closing report is sent if open/close
reporting is enabled, or at the end of Ex
it Delay. If
2 selected, ding
occurs upon reception of the wireless arming command.
V15P/V15PSIA NOTE:
This option
applies
only to
the
Telco reporting
path
(not for communication device)
.
UL:
must
be
1 for
UL
Commercial
Burglar
Alarm
inst.
∗
39
Power
Up In Previous State
0 = no, always power up disarmed;
1 = yes, power up in previous state
V20PSIA/V15PSIA:
Feature
always
enabled; field does not exist.
When the system powers up armed, an alarm will occur 1 minute after
arming if a zone is faulted. N
ote that if the previous state was armed
Away or Stay, the system ignores sensor changes for 1 minute, which
allows sensors such as PIRs to stabilize.
UL: must be 1
SIA Guidelines: must be 1
DIALER PROGRAMMING (
Q
40
–
Q
42)
Do not fill unused spaces. Enter 0–
9; #+11 for '
Q
'; #+12 for '#'; #+13 for a 2-
second pause. If fewer than the
maximum digits entered, exit the field by pressing [
∗
]. The next data field number is displayed.
∗
40
PABX Access Code or Call
Wai
ting Disable
Enter up to 6 digits.
To clear entries, press
Q40Q
.
If call waiting is used, enter call waiting
disable digits “
∗
(#+11) 70” plus “# +
13” (pause).
V20PSIA/V15PSIA:
If call waiting is
used, enter call waiting disable digits
as described above, and also set Call
Waiting Disable option in field *91.
| |
|
| |
Call Waiting:
If the subscriber’s phone service has “call waiting” (and
is not using PABX),
enter “*70” (“# + 11”) plus “# + 13” (pause) as the
PABX e
ntry to disable “call waiting” during control panel calls. If the
subscriber does not have “call waiting” and is not using PABX, make
no entry in this field.
NOTES:
1. The call waiting disable feature cannot be used on a PABX line.
2. Using Call Waiting Di
sable on a non-
call waiting line will prevent
successful communication to the central station.
VISTA-
15P/20P/SIA
Program
Guide
5
Data Field Programming
(Continued)
∗
41
∗
42
Primary Phone No.
Secondary Phone No.
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| | |
|
|
|
|
|
|
|
|
Enter up to 20 digits. To clear entries, press
Q
41
Q
or
Q
42
Q respectively
.
Enter the respective phone numbers.
∗
43
∗
44
∗
45
∗
46
Partition 1 Primary Acct. No.
Part. 1 Secondary Acct. No.
Partition 2 Primary Acct. No.
Partition 2 Secondary Acct. No.
Enter 4 or 10 digits, as chosen in *48
Report Format. Enter digits 0–
9; #+11
for B; #+12 for C; #+13 for D; #+14 for
E; #+15 for F.
| | | /
| | | | |
[FFFFFFFFFF]
| | | /
| | | | |
[FFFFFFFFFF]
| | | / | | | | |
[FFFFFFFFFF]
| | | / | | | | |
[FFFFFFFFFF]
Enter [
∗
] as the fourth digit if a 3-
digit account number (for 3+1 dialer
reporting format) is used. Enter 0 as the first digit of a 4-
digit account
no. for 0000-
0999. E.g., For Acct.
B234
, enter: #+11 + 2 + 3 + 4
To clear entries in a given field, press *43*, *44*, *45*, or *46* based
on the field being programmed
∗
47
Phone System Select
If Cent. Sta.
is not
on a WATS line:
0=Pulse Dial; 1=Tone Dial
If Cent. S
ta.
is
on
a WATS line:
2 = Pulse Dial
; 3 = Tone Dial
[1]
Select the type of phone service for the installation.
∗
48
Report F
ormat
0 = 3+1, 4+1 ADEMCO L/S STANDARD
1 = 3+1, 4+1 RADIONICS STANDARD;
2 = 4+2 ADEMCO L/S STAND.
3 = 4+2 R
ADIONICS STANDARD
5 = 10-
digit ADEMCO CONTACT ID®
REPORTING
6 = 4+2 ADEMCO EXPRESS
7 = 4
-digit ADEMCO CONTACT ID®
REPORTING
8 = 3+1, 4+1 ADEMCO L/S EXP.;
9 = 3+1, 4+1 RADIONICS EXP
[77]
primary
secondary
Select the format
for primary/secondary phone numbers
∗
49
Split/Dual Reporting
0 = Standard/backup reporting only (all
to primary)
1-5 = see table at right
[0]
Backup Reporting:
All reports are sent only to the primary number
unless unsuccessful
after 8 attempts. If unsuccessful, the system will
make up to 8 attempts to send all reports to the secondary number. If
still unsuccessful after the 16 attempts, the system displays the
“COMM. FAILURE” message (FC for fixed-
word displays).
Primary Phone
No.
2nd Phone No.
1 = Alarms, Restore, Cancel
Others
2 = All except Open/Close, Test
Open/Close, Test
3 = Alarms, Restore, Cancel
All
4 = All except Open/Close, Test
All
5 = All
All
VISTA-
15P/20P/SIA Program
Guide
6
Data Field Programming
(Continued)
∗
50
Burglary Dialer Delay
Delay
Time:
0 = no delay
1 = 15 seconds
2 = 30 seconds
3 = 45 seconds
V20PSIA/V15PSIA:
Delay Time:
1 = 15 seconds
2 = 30 seconds
3 = 45 seconds
Delay Disable:
0 = use delay set in entry 1
1 = dial delay disabled for zones
listed in zone list 6 (use zone list
6
to enter those zones that require
dial delay to be disabled; these
zones ignore the setting in entry
1)
UL: Dial delay plus entry delay must not exceed
one minute; use zone list 6 to disable dial delay
from appropriate zones, if necessary.
[2,0]
Delay
V20PSIA/V15PSIA
Time
Delay Disable
Provides delay of “BURGLARY ALARM” report to the central station,
which allows time for the subscriber to avoid a false alarm transmission.
This delay does not apply to zone type 24 alarms
(silent burglary) or to
24-
hour zone types 6, 7, and 8 (silent panic, audible alarm, auxiliary
alarm), which are always sent as soon as they occur.
UL: Delay Time must be 0
SIA Guidelines: delay must be minimum of 15 seconds
∗
53
SESCOA/Radionics Sel
ect
0 = Radionics (0-
9, B
-F)
1 = SESCOA (0
-
9 only reporting)
[0
Enter 0 for all non-
SESCOA formats.
∗
54
Dynamic Signaling Delay
0 = no delay (both signals sent)
1 = 15 secs
2 = 30 secs, etc.
UL: If using line security, must be 0.
Repor
ts will be sent to both the dialer and
the communication device.
[0]
Select delay from 0 to 225 secs, in 15-
sec increments.
Intended for reporting via a communication device on the ECP bus
(LRR). This field lets you select the time the panel
should wait for
acknowledgment from the first reporting destination (see
∗
55) before it
attempts to send a message to the second destination. Delays can be
selected from 0 to 225 seconds, in 15-
second increments. This delay
is per message. If
0 is entered
in this field, the control panel will send
redundant reports to both Primary Dialer and
communication device
.
∗
55
Dynamic Signaling Priority
0 = Primary Dialer first
1 = Communication Device (LRR) first
For UL Commercial Burglary installations
that use a DACT and LRR, this field must
be 0.
[0]
This field selects the primary communication path for reporting (dialer
or c
ommunication device) of
primary phone number
events
†
(see
∗
49 Split/Dual Reporting)
.
Dynamic signaling applies only to the primary phone number.
Reports
intended for the secondary phone number are not sent via the
communication device.
For Dynamic Signaling Priority:
Select the initial reporting
destination for messages as follows:
Primary Dialer First selected (
0
)
:
•
If acknowledged before delay expires (see
∗
54), then message will
not be sent via LRR.
•
If not acknowledged before delay expires, message is sent to both
the Primary Phone No. and via LRR.
Communication Device (LRR)
Fi rst selected (
1
)
:
•
If acknowledged before delay expires, then message will not be sent
to the primary dialer.
•
If not acknowledged before delay expires, message is sent to both
the Primary Phone No. and via LRR.
∗
56
,
∗
57
,
∗
58
Menu Modes
These are Menu Mode commands, not data fields, for Zone Programming, Function Key Programming, and Expert Mode
Zone Programming respectively. See page 3 and respective sections later in this document.
VISTA-
15P/20P/SIA
Program
Guide
7
Data Field Programming
(Continued)
TO PROGRAM SYSTEM ST
ATUS, & RESTORE REPO
RT CODES (
∗
59
thru
∗
68, *70
thru
∗
76,
and
∗
89):
For 3+1 or 4+1 Standard Format:
Enter a code in the
first
box:
1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.
A 0 (
not
#+10) in t
he
first
box disables
a report. A 0 (
not
#+10) in the
second
box result
s in advance to the next field.
For Expanded or 4+2 Format:
Enter codes in
both
boxes (1st and 2nd digits) for 1–
9, 0, or B
–F, as described above.
A 0 (
not
#+10) in the
second
box will
eliminate the ex
panded message for that report. A 0 (
not
#+10) in
both
boxes will
disable the report.
For Ademco Contact ID® Reporting:
Enter any digit (other than 0) in the
first
box, to enable zone to report (entries in the
second
boxes are ignored).A 0
(
not
#+10) in the
first
box disables the report.
UL
: Report codes are required in fields *61, *65, *71, *72, for UL Commercial Burglar Alarm installations.
Report codes are required in fields *60, *62, *63, *64, *70, *73, *74, *75, *76, for UL Commercial Burglar Alarm installations and required
for Residential Fire Alarm installations
SYSTEM STATUS REPORT CODES
(
Q
59–
Q
68)
∗
59
Exit Error Alarm Report Code
See above for entries.
V20PSIA/V15PSIA:
[1] Always enabled.
[0]
After arm
ing the system, entry/exit and interior zones remaining open
after exit delay expires cause an alarm sound at the keypad and
external sounder (keypad also displays “EXIT ALARM”), and entry
delay begins. Disarming before the end of the entry delay stops the
alarm sounding and no message is sent to the central station.
Keypad
display
s “CA” (fixed
-word) or “ALARM CANCELED” (alpha display).
If the system is not disarmed before entry delay expires, an “EXIT
ALARM” message (
V20PSIA/V15PSIA:
also
, zone alarm messa
ge) will
be sent to the central station. The keypad will display “EA” (fixed-
word
)
or “EXIT ALARM” (alpha display), and alarm sounding continues until
the system is disarmed (or timeout occurs).
An Exit Alarm condition will also result if a fault occurs
in an exit or
interior zone within 2 minutes following the end of the exit delay, and
an “EXIT ALARM” message will be sent to the central station (except
for
V20PSIA/V15PSIA
, see field *69 Recent Closing report).
With
Contact ID format, the message will contain the zone number and
error code 374 (“ALARM
–
EXIT ERROR”).
∗
60
Trouble Report Code
See above for entries.
|
[10]
See
UL
System
Reporting
Note
above
*59.
Sent if a zone has a trouble condition.
∗
61
Bypass Report Code
See
above for entries.
|
[00]
See
UL
System
Reporting
Note
above
*59.
Sent when a zone is manually bypassed.
∗
62
AC Loss Report Code
See above for entries.
|
[10]
See
UL
System
Reporting
Note
above
*59.
Timing of
this report is random with up to a 4-
hour delay. If AC
restores before the report goes out, there is no “AC
LOSS” report.
∗
63
Low Bat Report Code
See above for entries.
|
[10]
See
UL
System
Reporting
Note
above
*59
Sent when the s
ystem’s backup battery has a low
-
battery condition.
∗
64
Test Report Code
See above for entries.
Periodic Test Report Schedul
e
Commands:
every 24 hrs = installer code +
[#]
+ [0] + 0
once per week = installer code +
[#]
+ [0] + 1
every 28 days = ins
taller code +
[#]
+ [0] + 2
|
[00]
See
System
Reporting
UL
Note
above
*59.
Sent periodically to test the communicator and phone lines.
Frequency of report is set in Scheduling mode (event 11) or by the key
commands listed at left:
Ea
ch mode sets schedule 32 (VISTA
-20P) or schedule 08
(VISTA-
15P) to the stated repeat option; first test report sent 12 hours
after command.
†
† NOTE:
Make sure the Real
-Time Clock is set to the proper time
before
entering the test report schedule command to ensure that test reports are sent
when expected. (see Setting the Real
-
Time Clock section)
VISTA-
15P/20P/SIA Program
Guide
8
Data Field Programming
(Continued)
∗
65
Open Report Code
See above for entries.
[0,0,0]
System
Reporting
Note
above
*59.
Part. 1
Part. 2
Common
Sent upon disarming the system in the selected partitions.
See
UL
∗
66
Arm Away/Stay Rpt Code
See above for entries.
[0,0,0,0,0,0]
Away
Stay
Away
Stay
Away
Stay
Part. 1
Part. 2
Common
This option allows for independent programming of Away and Stay
reports for each partition, including the common lobby.
NOTE:
“OPEN” reports are not sent if the associated closing report is
not enabled.
∗
67
RF Trans. Low Bat Report Cod
e
See above for entries.
|
[00]
UL:
must
be
enabled
if wireless
devices
are
used
Sent when a transmitter low
-battery condition exists.
∗
68
Cancel Report Code
See above for entries.
V20PSIA/V15PSIA:
[10]
Report enabled.
|
[00]
Sent upon disarming the system after an alarm condition was
reported.
∗
69
Recent Closing Report Code
Not applicable to V15P/V20P
See above for entries.
V20PSIA/V15PSIA:
Always enabled.
|
[11]
V20PSIA/V15PSIA:
Field does not apply to other controls.
Similar to the Exit Error condition described in field *59, but occurs if
any burglary zone is faulted within two minutes
after
the initial exit
delay expires. Disarming the system within the two minutes stops
the alarm sound and displays "ALARM CANCELED " or "CA" and
faulted zone number. No message is sent to the Central Monitoring
Station.
If the system is not disarmed within two minutes, the alarm sound
continues and a “recent closing” and a “zone alarm” message are
sent to the Central Monitoring Station (after dial delay expires).
RESTORE REPORT CODES (
Q
70
–
Q
76)
∗
70
Alarm Restore Rpt Code
See above for entries.
[0]
Alarm restore signals indicate that respective alarm zone(s) are no
longer faulted. Alarm restore reports are sent to the central station at
bell timeout (field *33), if t
he zone(s) in alarm are actually restored to a
non-
faulted state at that time. Otherwise, alarm restore report(s) for
respective alarm zones are sent when the system is disarmed.
See
UL
System
Reporting
Note
above
*59.
If
Reports Per Armed Period Per Zone
(*93) is also programmed, the
system will report alarm and restore codes as described above until
the “Reports Per Armed Period” count is reached. Disarming and
rearming will reset the “Reports Per Armed Period” count.
∗
71
Trouble Restore Rpt Code
See
above for entries
|
[00]
Sent when a trouble in a zone is restored and code + OFF performed.
See
UL
System
Reporting
Note
above
*59.
∗
72
Bypass Restore Rpt Code
See above for entries.
|
[00]
Sent when a zone that
has been bypassed is unbypassed.
See
UL
System
Reporting
Note
above
*59.
∗
73
AC Restore Rpt Code
See above for entries.
|
[00]
See
UL
System
Reporting
Note
above
*59.
Sent after AC power has been restored after an AC power out
age.
∗
74
Low Bat Restore Rpt Code
See above for entries.
|
[00]
See
UL
System
Reporting
Note
above
*59.
Sent after a system low
-battery condition is restored to normal.
VISTA-
15P/20P/SIA
Program
Guide
9
Data Field Programming
(Continued)
∗
75
RF Trans.
Lo Bat R
st Rpt Code
See above for entries.
|
[00]
Sent when a transmitter’s low battery condition is restored (i.e., new
battery installed).
UL: must be enabled if wireless devices are used. See UL System Reporting
Note above *59.
∗
76
Tes
t Restore Rpt Code
See above for entries.
|
[00]
See
UL
System
Reporting
Note
above
*59.
This is sent when the Test mode is exited or upon timeout (4hrs).
OUTPUT AND SYSTEM SETUP (
Q
77
–
Q
93)
∗
77
Daylight Saving Time Start/End
Month
0 = Disabled
1-9 = Jan.
-Sept
. (1 = Jan, 2 = Feb, etc)
#+10 = October
#+11 = November
#+12 = December
|
[3][11]
Enter the start and end month for daylight saving time, if applicable to
the region.
∗
78
Daylight Saving Time Start
/End
Weekend
0 = disabled
4 = fourth
1 = first
5 = last
2 = second
6 = next to last
3 = third
7 = third to last
|
[2][1]
Enter the start and end weekend for daylight saving time, if applicable
to the region.
∗
79
,
*80
,
*81
,
*82
Menu M
odes
These are Menu Mode commands, not data fields, for Output Device Mapping, Output Programming, Zone List
Programming, and Alpha Programming respectively. See page
3 and their respective sections for procedures.
∗
84
Auto Stay Arm
0 = no
1 = partiti
on 1 only
2 = partition 2 only
3 = both partitions
[3]
If enabled, the system will automatically change AWAY mode to STAY
mode if the entry/exit door
is not
opened and closed within the exit
delay time after a user arms in AWAY mode from a wired keypad
(non-
RF device). An Opening report followed by an Armed Stay report
is sent to the Central Station.
If the door
is
opened and closed within the exit delay period, the
system remains in AWAY mode.
Any RF device that arms the system AWAY overrides this feature and
the system remains armed AWAY.
∗
85
Cross Zone Timer
0 = 15 secs
6 = 2-
1/2 min
#+12 = 8 min
1 = 30 secs
7 = 3 min
#+13 = 10 min
2 = 45 secs
8 = 4 min
#+14 = 12 min
3 = 60 secs
9 = 5 min
#+15 = 15 min
4 = 90 secs
#+10 = 6 min
5 = 2 min
#+11 = 7 min
[0]
Sets the maximum amount of time in which two cross zones must be
tripped in an armed system to send an alarm message to the Central
Station. If only one
zone is tripped during this time
(and
2
nd
zone
is not
tripped)
, a trouble message (CID code 380) for that zone is sent to the
Central Station.
Assign cross zones on zone list 4;
see
*81 Menu mode.
NOTE:
Cross zoni
ng takes effect only after Exit Delay expires.
∗
86
Cancel Verify Keypad Display
0 = no “alarm canceled” display
1 = display “Alarm Canceled” when
system is disarmed after an alarm has
occurred. (To clear the “ALARM
CANCELED” display, the user must
ent
er the security code + OFF again.)
NOTE:
Applies only when the Dialer is
selected as the primary communication
path (
∗
55 = 0).
[1]
This feature causes an
“
ALARM CANCELED”
display on the LCD keypad
under the following conditions:
•
After the k
issoff of the cancel message to the Central Station, indicating a
successful transmission.
•
When an alarm is successfully canceled before the Central Station received
the Alarm message. E.g., if an alarm is incorrectly triggered and the user
presses code + OFF before the dial delay time has expired, the message will
never go out to the CS.
•
When the Cancel report is not enabled and the system is disarmed:
a.
before
dialer delay expires (alarm report not sent) message “Alarm
Canceled” is displayed.
b.
after
dialer delay expires message “Alarm Canceled” is not displayed
.
VISTA-
15P/20P/SIA Program
Guide
10
Data Field Programming
(Continued)
∗
87
Misc. Fault Delay Time
0 = 15 secs
6 = 2-
1/2 min
#+12 = 8 min
1 = 30 sec
7 = 3 min
#+13 = 10 min
2 = 45 secs
8 = 4 min
#+14 = 12 min
3 = 60 secs
9 = 5 min
#+15 = 15 min
4 = 90 secs
#+10 = 6 min
5 = 2 min
#+11 = 7 min
UL: may only be used on non-
burglar
alarm/ non-
fire alarm zones when used in
fire and/or UL burglar alarm installation
[0]
(used with Configurable Zone Types “digit 6”)
Used
with zones assigned to a configurable zone type with fault delay
on (configurable zone type digit “6”), and sets a zone response time of
15 seconds to 15 min. It can be assigned to zones with sensors that
provide a trouble indication when an oil tank is l
ow, or similar
applications for critical condition monitoring where a non-
alarm
response is desired.
∗
88
Program Mode Lockout Options
0 = standard *98 installer code lockout
(reentry only by [
∗
] + [#] within 50 secs
after power up)
1 = lockout [
∗
] + [#
] reentry after *98
exit
(reenter via installer code or
downloader only)
2 =
lockout local programming after *98
exit
(reenter by downloader only)
[0]
This table summarizes the Program Mode Lockout options:
Exit
*88
Reentry By:
Command
En
try
Installer
Power
-up†
Downloader
*99
n/a
yes
yes
yes
*98
0
no
yes
yes
*98
1
yes
no
yes
*98
2
no
no
yes
†
pressing [
∗
] + [#] within 50 seconds of power up
∗
89
Event Log Full Report Code
See box above field *59 for report code
entries.
|
[00]
If an Event Logging selection is made in field
∗
90, a message can be
sent to the central station receiver when the log is 80% full. If the log
becomes full, new messages overwrite the oldest messages in the log.
∗
90
Event Log Enables
0 = None
1 = Alarm/Alarm Restore
2 = Trouble/Trouble Restore
4 = Bypass/Bypass Restore
8 = Open/Close.
Example:
To select “Alarm/Alarm
Restore”, and “Open/Close”, enter 9 (1
+ 8)
To select all, enter #15.
[3]
This system can record various events in a history log (VISTA
-20P =
100 events; VISTA
-15P = 50 events). At any time, the downloader
operator can then upload the log and view or print out all or selected
categories of the log, or
can clear the log. Event log can also be
viewed at an alpha keypad. The display/printout at the central station
will show the date, time, event, and description of the occurrences.
Data Entry Example: To select Alarm/Alarm Restore” and
“Open/Close”, enter 9 (1+ 8); to select all events, enter #15.
NOTE
:
Sy
stem messages are logged when any non
-
zero entry is made.
∗
91
Option Selection
Entry 1:
Options
0 = None
1 = Bell Supervision Processing
8 = Exit Delay Restart/Reset
†
V20PSIA/V15PSIA:
Entry 1
Options:
Same as above.
Entry 2
Call Waiting Disable
:
0 =
call waiting not used
1 =
use
call wait
ing disable digits
(
∗
70) entered in field
∗
40; (when
selected, the system dials the
entry in
∗
40 only on alternate dial
attempts; this allows proper
dialing in case call waiting
service is later canceled by the
user).
[8, 0]
Options
V20PSIA/V15PSIA: Call Waiting Disable
SIA Guidelines: Exit Delay
Restart/Reset
should be enabled.
† “Exit Delay Restart/
Reset” option allows use of the [
∗
] key to restart
the exit delay at any time when the system is armed STAY or
INSTANT. This feature also enables automatic exit delay reset, which
resets exit delay if the entry/exit door is re-
opened and closed before
exit delay time expires after arming AWA
Y. Automatic Exit Delay
Reset occurs only once during an armed AWAY period.
VISTA-
15P/20P/SIA
Program
Guide
11
Data Field Programming
(Continued)
∗
92
Phone Line Monitor Enable
Entry 1:
:
0 = disabled, 1-
15 = 1 min
- 15 min
(#+10 = 10 min; #+11 = 11 min;
#+12 = 12 min; #+13 = 13 min;
#+14 = 14 min; #+15 = 15 min)
Entry 2
:
0 = Keypad display when line is faulted
1 = Keypad display plus keypad trouble
sound.
Each partition turns off its
own trouble sound. No automatic
timeout.
2 = Same as “1”, plus programmed
output device STARTS. If either
partition is armed, external
sounder activates also.
External
sounder will be turned off by
normal bell timeout, or by security
code plus OFF from either partition
(it need not be the one that was
armed).
[0,0]
1
2
Entry 1:
Sets the length of time a phone line fault must remain after
detected before the second digit option is activated.
Entry 2:
Selects the desired phone line fault response.
Option 2 may be used even if a relay unit or Powerline carrier device
is not connected to the control.
Programmed Output Device must either be prog
rammed to be
STOPPED in field
∗
80 or STOPPED by entry of [security code] + [#] +
8 + device number. Partition in
∗
80 should be set to “0,” for STOP.
UL: Field *92 must be enabled for fire alarm installations, UL commercial
burglar alarm installations and U
L residential burglar alarm installations.
If the control unit is used on a UL commercial burglar alarm system which
requires 2 methods of remote communication, then the control unit’s DACT
and the other method of signal transmission must monitor each other against
communication failure and line fault. The fault must be received and
annunciated within 200 seconds of its occurrence.
∗
93
Reports
i
n Armed Period Per
Zone
(Swinger Suppression)
Restrict Report Pairs:
0 = Unlimited Reports
1 = 1 report
pair
per zone per armed
period
2 = 2 report pairs
per zone per armed
period
V20PSIA/V15PSIA:
Restrict Report Pairs:
1 = 1 report pair; 2 = 2 report pairs
Unlimited Reports Enable:
0 = restrict reports to the setting in
entry 1
1 = unlimited reports for
zones listed
in zone list 7; (use zone list 7 to
enter those zones that require
unlimited reporting; these zones
ignore the setting in entry 1)
[V20P/V15P =
1,0; V20PSIA/V15PSIA = 2,0
]
Restrict
V20PSIA/V15PSIA
Report Pairs
Unlimited Reports Enable
Selection limits the number of alarm/alarm restore message pairs
per zone sent to the CS in an armed period.
Swinger suppression applies to burglary zones only.
NOTE
: The zone is automatically bypassed after the programmed
number of alarms is triggered.
SIA Guidelines: Must be set for option
2
DOWNLOAD INFORMATION (
Q
94,
Q
95)
∗
94
Download Phone No.
Enter up to 20 digits, 0–
9; #+11 for '
Q
';
#+12 for '#'; #+13 for a 2-
second
pause. Do not fill unused spaces. If
fewer than 20 digits, exit field by
pressing
Q
. To clear entries from field,
press
Q
94
Q
.
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enter the phone number of the downloading computer.
UL: downloading may be performed only if a technician is at the site.
Up/downloading via the Internet has not been evaluated by UL.
VISTA-
15P/20P/SIA Program
Guide
12
Data Field Programming
(Continued)
∗
95
Ring Count
f
or Downloading
0 = Disable Station Initiated
Download;
1–14 = number of rings (1
–9, # +10
=10, # +11 =11, # +12 =12,
# +13 =13, # +14 =14);
15 = answering machine defeat
(# +15 =15).
NOTE:
Do not enter 0 if using
4286 Phone Module.
[15]
Refer to the chart below and program accordingly.
phone
answer
down-
module
machine
loading
Set field
∗
95 to...
yes
no
no
1-14 (not 0)
yes
yes
no
greater
than rings set on answer machine
(e.g., if ans. machine is 4 rings, set this field
to 5). This allows access to the phone module
if the answer machine is off.
yes
no
yes
1-14 (not 0)
yes
yes
yes
15 (bypasses answer machine
†
)
no
no
no
0
no
yes
no
0
no
no
yes
1-14
no
yes
yes
15
†
NOTE:
If “15” is entered to bypass an answering machine, and a 4286 Phone
Module is included in the system, you should note the following:
When calling in
from an off
-premises phone, the user should make the initial call,
allow 1 or 2 rings only, then hang up, then call again. The phone module will now
seize the line, and 2 long tones sound, followed by the usual voice prompt for the
access code. If this pr
ocedure is not followed, phone module operation will not be
possible.
∗
96
,
∗
97
Initialize/Reset Defaults
(
Thes
e are
commands
, not data fields
. See page 3
.)
∗
98
,
∗
99
Exit Commands
(
These are commands, not data fields
. See page 3
.)
PAGER OPTIONS (
Q
160-
Q
172)
The system can send various reports to several pagers (VISTA
-20P = up to 4; VISTA
-15P = up to 2).
To program pager reporting, do the following:
1. Enter the pager phone number(s), preface characters, and pager report options in data fields *160
- *171.
2. Enable Pager Delay, if desired, in field *172 (delays alarm reporting for ALL pagers).
3. Make sure appropriate user open/close pager reports are enabled (see Security Codes
section in User Guide)
. Users that perform
actions in partition 1 wil
l, if enabled, attempt to report to all pagers enabled for open/close reporting in partition 1. Users that
perform actions in partition 2 will, if enabled, attempt to report to all pagers enabled for open/close reporting in partition 2.
4. If using latchkey pager report, define the latchkey report schedule using Scheduling mode (master code + [#] [6] [4] then select
event type
03
). System must be armed for the Latchkey report to be sent.
5. If using a function key to manually send a message to a pager, use *57 Function Key Menu mode to define the key (function
01
).
6. If reporting zone alarms and troubles to a pager, use *81 Zone List menu mode to assign the zones associated with each pager
(zone lists 9-
12
†
).
† VISTA-
15P supports zone lists 9 and 10 only.
∗
160
Pager 1 Phone No.
Enter up to 20 digits. 0–
9
#+11 = '
Q
'
#+12 = '#'
#+13 = 2
-
sec
ond
pause
| | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If entering fewer than 20 digits, exit
by pressing [
∗
] + next field
number. To clear entries, press
∗
160
∗
.
∗
161
Pager 1 Characters
Enter the optional prefix characters, up
to 16 digits.
0–9
#+11 = '
Q
'
#+12 = '#'
#+13 = 2-
second pause
Display Example 1.
911–
1004
Indicates an alarm (911)
caused by a
fault in zone 4 (0004) in part. 1.
Display Example 2.
102–
2005
Indicates the system is reporting a
closing–
system arming (102) by User
5 (0005) in partition 2.
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Up to 16 optional characters may be sent as a prefix to the 7-
digit system status
code sent to Pager #1 (if used). Phone number in field *160 must have been
entered. If fewer than 16 characters, exit by pressing [
∗
] and next field number.
To clear entries: press
∗
161
∗
.
The 16 characters may be composed of the following:
PIN number, Subscriber account number,
∗
character
, # character
, 2-second pause,
†
special character(s) the user may decide to transmit
† Some paging systems require pause(s) before the prefix.
The Pager format for the 7-
digit status code is defined as follows: XXX
-YYYY
where:
XXX
= 3-digit event code:
911 = Alarm, 811 = Trouble, 101 = Opening
(disarm), 102 = Closing (arm AWAY)
YYYY
= 4-digit user or zone number (depending on type of event). The first
digit indicates partition (0 = system, 1 = part 1, 2 = part 2, 3 =
common), followed by the 3-
digit user or zone number.
VISTA-
15P/20P/SIA
Program
Guide
13
Data Field Programming
(Continued)
∗
162
Pager 1 Report Options
0 =
no reports sent
1 =
Opens
/closes all users
†
4 =
All alarms and troubles
5 =
All alarms / troubles, and
opens/closes for all users
12 =
Alarms / troubles for zones
entered in zone list 9
13 =
Alarms / troubles for zones
entered in zone list 9, and
opens/closes for all users
[0,0,0]
P1 P2 comm
For each partition, select from the listed options.
† For users enabled for paging.
Reports to pager only when arming
(close)/disarming (open) from a keypad using a security code; auto-
arming/disar
ming, arming with assigned button, and keyswitch arming
do not send pager messages.
∗
163
Pager 2 Phone No.
See field
∗
160 for entries.
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
If enteri
ng fewer than 20 digits, exit by pressing [
∗
] + next field
number. To clear entries, press
∗
163
∗
.
∗
164
Pager 2 Characters
See field
∗
161 for entries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If fewer than 16 characters, exit by pressing [
∗
] and next field number.
To clear entries, press
∗
164
∗
.
∗
165
Pager 2 Report Options
See field *162 for reporting options.
[0,0,0]
P1 P2 comm
Select fo
r each partition (use zone list 10 for options 12 or 13)
∗
166
Pager 3 Phone No.
See field
∗
160 for entries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If entering fewer than 20 digits, exit by
pressing [
∗
] + next field
number. To clear entries, press
∗
166
∗
∗
167
Pager 3 Characters
See field
∗
161 for entries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If fewer than 16 characters, exit by pressing [
∗
] and next field number.
To clear entries, press
∗
167
∗
.
∗
168
Pager 3 Report Options
See field *162 for reporting options.
[0,0,0]
P1 P2 comm
Select for each partition (use zone list 11 for options 12 or 13).
∗
169
Pager 4 Phone No.
See field
∗
160 for entries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If entering fewer than 20 digits, exit by pressing [
∗
] + next field
number. To clear entries, press
∗
169
∗
.
∗
170
Pager 4 Characters
See field
∗
161 for entries.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
If fewer than 16 characters, exit by pressing [
∗
] and next field number.
To clear entries, press
∗
170
∗
.
∗
171
Pager
4 Report Options
See field *162 for reporting options.
[0,0,0]
P1
P2
comm
Select for each partition (use zone list 12 for options 12 or 13).
∗
172
Pager Delay Option For Alarms
0 = none
1 = 1 minute
2 = 2 minutes
3 = 3
minutes
[3]
This field determines the delay of alarm reports to the pager. This
gives the Central Station enough time to verify the alarm report it
received before the dialer attempts to dial the pager.
This delay is for ALL pagers in the sys
tem.
MISCELLANEOUS SYSTEM FIELDS (*174
-*181)
∗
174
Clean Me Reporting Options
0 = disable
1 = Clean Me signal reports
[0]
For ESL smoke detectors
This is a maintenance feature for ESL 2-
wire smoke detectors on
Zone 1. If used, this option limits the number of smoke detectors to a
maximum of 10, rather than 16. To enable the “clean me” feature, a
time response setting of “3” (1.2 seconds) must be entered in
∗
56
Zone Programming for zone 1.
NOTE:
If Clean Me is enabled, you must enter “3”
in field
∗
56
programming for zone 1 response time.
VISTA-
15P/20P/SIA Program
Guide
14
Data Field Programming
(Continued)
∗
177
Device Duration 1, 2
0 = 15 secs
6 = 2-
1/2 min
#+11 = 7 min
1 = 30 secs
7 = 3 min
#+12 = 8 min
2 = 45 secs
8 = 4 min
#+13 = 10 min
3 = 60 secs
9 = 5 min
#+14 =
12 min
4 = 90 secs
#+10 = 6 min
#+15 = 15 min
5 = 2 min
[0] [0]
1
2
(used in *80 Menu mode-
Device Actions 5/6)
These entries set the duration for output action options 5 (duration 1)
and 6 (duration 2) programmed in
∗
80
Output Function Programming.
∗
181
50/60 Hertz AC Operation
0 = 60 Hz; 1 = 50 Hz
[0]
Select the type of AC power applied to the control (option is used for
Real
-
Time Clock synchronization)
CONFIGURABLE ZONE TYPE OPTIONS (*182
-*185)
(see Configurable Zone Type Worksheet
following
data field
∗
199)
•
The system allows you to define custom zone types (VISTA
-20P supports 4 [types 90-
93]; VISTA
-15P supports 2 [types
90, 91]) based on the options
select
ed.
•
All configurable zone types can
be programmed via the downloader. Zone types 90-
91 can also be programmed from a
keypad using data fields *182-
*185.
•
IMPORTANT:
Be careful when selecting combinations of options for configurable zone types. Contradictory options can
cause unpredictable r
esults.
Configurable Zone Type Options
Auto Restore
(entry 2): Faults on zones set for this option are cleared; restore messages sent upon restoral of faults.
Vent Zone
(entry 2): Zones set for this option are ignored if faulted when arming the system, but are protected if the zone is later restored
(e.g., an open window can be ignored when arming, but if the window is later closed, it will be protected; opening the window
again causes
an alarm.)
NOTE: Vent zones are not for use in UL installations.
Bypass
Disarmed
(entry 4): Zones set for this option can be bypassed only while the system is disarmed.
Bypass Armed
(entry 4): Zones set for this option can be bypassed when the system is armed.
Dial Delay
(entry 6): Alarms on zones set for this option participate in dial delay central station reporting, if system dial delay enabled in
field *50.
Fault Delay
(entry 6): Faults on zones set for this option are delayed by the time set in field *87. Do not use this option if using entr
y/exit
delay for this zone type.
Faults Display
(entry 7): Selects how faults on zones set for this zone type are displayed.
Power Reset/Verification
(entry 7): Selects whether the system resets power (when user enters code + OFF), and whether the system
performs alarm verification (see description for zone type 16 in
Zone Type Definitions
section) when a fault occurs on these zones.
Use Entry Delay
(entry 8): Selects whether to use the system’s entry delay times.
Use Exit Delay
(entry 8): Selects whether to use the system’s exit delay t
ime.
Interior Type
(entry 8):
Zones
set for this option
are treated same as standard zone type 4 (bypasses when armed STAY, faults displayed).
Alarm Sounds
(entry 9):
Selects the type of alarms sound for zones
set for this zone type.
Bell Timeout
(entry 9)
: Alarm sounding on zones
set for this option
remain for the duration set in fields *32 / *33.
Fire Zone
(entry 9):
Zones
set for this option
respond in the same manner as if programmed for zone type 9. Do not set fire zones to
respond as a “fault” in entr
ies 1-
6.
Trouble Sounds
(entry 10):
Selects the type of trouble sounds for zones set for this zone type (periodic beeps = once every 30 seconds;
trouble beeps = rapid beeping).
Chime Enable
(entry 10):
Zones
set for this option cause a chime when Chime mode is on.
∗
182
Configurable Zone Type 90
(0-9, #+10=10, #+11=11, #+12=12,
#+13=13, #+14=14, #+15=15).
1
2
3
4
5
6
7
8
9
10
Enter the appropriate value for each entry, 1-
10, based on the charts
provided in the Configurable Zone Type Worksheet section. Each
entry is the sum of the values of its selected options
To calculate the value for each entry, add t
he values of the selected
options in each of the entry’s columns shown in the respective chart
(one option per column). For example, to program entry 2 for “alarm
response to short,” “auto restore on,” but not a “vent zone,” enter 5
(“1” for alarm short +
“4” for auto restore-
yes + “0” for vent zone-
no).
UL:
Do
not
configure
zones
as a fire
alarm
or UL
burglar
alarm
zone.
VISTA-
15P/20P/SIA
Program
Guide
15
Data Field Programming
(Continued)
∗
183
Zone Type 90 Report Codes
90 ALARM ID: XXX
TROUBLE ID: XXX
Press [
∗
] when done to continue.
NOTE:
Zone alarm report codes and
trouble report code (
∗
60) and relevant
restore codes must be enabled in order
to report configurable zone type codes.
Enter the desired 3
-
digit Contact ID® report codes for alarms and
troubles occurring on zones assigned to this zone type. Enter the
codes sequentially (all 6 digits). When entering digits, [#] moves
cursor back, [
∗
] moves forward.
Important Notice on Report Codes:
To avoid confusion at the
central station, it is recommended that existing Contact ID® c
odes be
used with configurable zone types whenever possible. Check with the
central station for a complete list of Contact ID® report codes. If none
of the codes are suitable, choose a code in the reserved range of 750-
789 and make sure to define the code
with your central station.
∗
184
Configurable Zone Type 91
(0-9, #+10=10, #+11=11, #+12=12,
#+13=13, #+14=14, #+15=15).
1
2
3
4
5
6
7
8
9
10
See
∗
182 for entries.
UL:
Do
not
configure
zones
as a fire
alarm
or UL
burglar
alarm
zone.
∗
185
Zone Type 91 Report Codes
91 ALARM ID: XXX
TROUBLE ID: XXX
See
∗
183 for entries.
∗
18
8
Keypad Lockout
0 =
disable
1 = enable
Alpha keypad display
:
Line 1 “User Code Error:”
Line 2 “Keys 0-
9 Locked”
Fixed Glass keypad display
:
“CE” (Code Error)
[1]
If enabled
:
•
The system
lock
s out the keypad f
or 15 minutes if 30 keystrokes
are
made without a valid user code being detected.
(30 keystrokes =
6 attempts of code + command)
•
While locked out,
the
message "User Code Error"
is displayed on
alpha keypads in the partition that is locked out.
•
Upon lockout, a
message
is transmitted to the central station
(Contact ID event 461 Wrong Code Entry), as well as being logged
in the event log.
•
When the 15-
minute lockout window expires, a Restore message is
sent to the Central Station and entered into the Event Log.
•
Lockout
period
ends and the display clears when lockout time
expires, or an alarm occurs, or entry delay begins.
If disabled
:
•
The “Wrong Code Entry” (event 461) message is
added to
Event Log.
•
No report is sent to the central station.
•
No message is displayed on the keypad.
•
No resto
re event is entered in the event log.
VISTA-
15P/20P/SIA Program
Guide
16
Data Field Programming
(Continued)
∗
189
AUI Device Enables
(for
Touchscreen
Style Keypads)
VISTA
-20P:
For
Touchscreen device
usage
0 = disable
1 = partition 1
2 = partition 2
3 = partition 3 (
common)
For Remote Services device usage
5 = part. 1 (auto-
stay arm disabled)
6 = part. 2 (auto-
stay arm disabled)
7 = part. 3 (common; auto-
stay arm
disabled)
VISTA
-15P:
For
Touchscreen device
usage
0 = disable
1 = enable
For Remote Services device usage
5 = part. 1 (auto-
stay arm disabled)
Device Addresses:
Touchscreen device 1: Must set to 1
Touchscreen device 2: Must set to 2
Touchscreen device 3: Must set to 5
Touchscreen device 4: Must set to 6
[1, 1, 0, 0]
AUI 1
AUI 2
AUI 3
AUI 4
System supports touchscreen style keypads (e.g.,
6280, Tuxedo
Touch; V20P = up to 4; V15P = up to 2).
NOTE:
Use of touchscreen style keypads does not affect the number
of standard keypads supported.
To enable a touchscreen keypad, enter the option corresponding to
each touchscreen’s home partition.
Note for Remote Services Devices:
If using the Remote Services
feature of the communication device, select an option 5-
7, depending
on the partition the
Remote Services device is associated with (these
options automatically disable auto-
stay arming when the system is
armed from the respective Remote Services device). Refer to the
communication device’s installation instructions for details on enabling
the Remote Services feature.
Note for Remote Services Device Address:
Using an AUI device
address for Remote Services provides enhanced remote services
features, but an actual AUI device cannot use the same address. If no
AUI addresses are available (all four AUIs are being us
ed), Total
Connect 2 cannot be used for remote services. However, Total
Connect 1 can be used by choosing an available standard keypad
address and using the appropriate keypad address field *190
- *196 to
select the Remote Services operating partition (som
e remote access
features will be unavailable).
KEYPAD OPTIONS *190
-*196
To enable keypads:
1. Set desired address at keypad (refer to keypad’s instructions for setting the address).
2. Use data fields *190-
*196 to enable keypad addresses, assign a par
tition,
and
enable sound options.
3. Use fields *197, *198, and *199 to turn on partition number display, exit time interval display, and select fail display mode.
4. Set keypad-
related data fields as appropriate: *21 Quick Arm Enable, *23
Forced Bypass,
*84
Auto STAY Arm
NOTES
:
1. Options for keypad 1, address 16, are set by the factory and cannot be changed.
2. Each keypad must be assigned a unique address. Keypads programmed with the same address will give
unpredictable results.
∗
190
Keypad 2
Device Address 17
Entry 1
: Partition/ Enable
VISTA
-20P
: Enter partition in which the
keypad is located
where:
For
Standard keypad
usage
0 = disable
1 = partition 1
2 = part. 2
3 = part. 3 (common)
For Remote Services device usage
5 = part. 1 (auto-
stay
arm disabled)
6 = part. 2 (auto-
stay arm disabled)
7 = part. 3 (common; auto-
stay arm disabled)
VISTA
-15P
:
For
Standard keypad
usage
0 = disable
1 = enable
For Remote Services device usage
5 = auto-
stay arm disabled
Entry 2
: Sound
0 = no suppression
1 = suppress arm/disarm and Entry/Exit
beeps
2 = s
uppress chime beeps only
3 = suppress arm/disarm, Entry/Exit, and
chime beeps
[1] [0]
Partition/
Sound
Enable
Entry 1 -
Parti
tion/Enable:
Enter the desired option for the keypad’s
home partition.
Note for Remote Services Devices:
If using the Remote Services
feature of the communication device, select an option 5-
7 (option 5 for
VISTA-
15P), depending on the partition the
Remote Services device is
associated with (these opti
ons automatically disable auto-
stay arming
when the system is armed from the respective Remote Services
device). Refer to the communication device’s installation instructions
for details on enabling the Remote Services feature.
Entry 2
- Sound:
Enter the
desired sound option for this keypad.
VISTA-
15P/20P/SIA
Program
Guide
17
Data Field Programming
(Continued)
∗
191
Keypad 3 Device Address 18
See field
∗
190 for entries.
[1] [0]
Part
.
/ Enable
Sound
∗
192
Keypad 4 Device Address 19
See field
∗
190 for entries.
[1] [0]
Part./ Enable
Sound
∗
193
Keypad 5 Device Address 20
See field
∗
190 for entries.
[1] [0]
Part.
/ Enable
Sound
∗
194
Keypad 6 Device Address 21
See field
∗
190 f
or entries.
[1] [0]
Part.
/ Enable
Sound
∗
195
Keypad 7 Device Address 22
See field
∗
190 for entries.
[1] [0]
Part.
/ Enable
Sound
∗
196
Keypad 8 Device Address 23
See field
∗
190 for
entries.
[1] [0]
Part.
/ Enable
Sound
∗
197
Exit Time Display Interval
0 = no display
1-5 = seconds between display refresh
TOUCH SCREEN DEVICE NOTE:
If
using more than one touch screen
device (e.g., 6280, Tuxedo
Touch
) with
the system, leave field *197 Exit Time
Display Interval set to the default value
“0.” The 6280
automatically displays
remaining exit time in one-
second
increments.
[0]
If enabled, keypads display the exit time remaining after arming the
system, updated at the interval selected (i.e. if the exit delay is 30
seconds and “2” is selected in this field, the keypad display refreshes
every 2 seconds, displaying 30, 28, 26, 24, etc.).
An interval greater than “1” may be necessary for some older keypads
to allow users time to enter key presses between display updates.
NOTE:
If enabled and using only 2-
digit fixed-
word keypads (e.g.,
6150RF), do not set exit delay time greater than 96 seconds.
Using a
longer delay time may cause end-
user conf
usion because 2-
digit
display keypads cannot display times greater than “99.” If longer exit
time is required by the installation, it is recommended that the Exit
Time Display option be disabled (“0”).
∗
198
Display Partition Number
0 = no
1 = yes (part.
no. appears on
display)
[0]
(VISTA
-
20P; for Alpha Display Keypads)
If selected, the partition number is displayed in the upper
-left corner of
the
alpha
display. This is useful when using the GOTO partition
function.
∗
199
ECP Fail Disp
lay
0 = 3
-digit display
“1” + device address)
1 = 2
-digit fixed-
display as “91
[0]
Select “0” if using Alpha keypads and/or 3-
digit Fixed-
Word Display
keypads. ECP faults will display “1” plus the device address (00-
15
) of
device causing t
he fault (e.g., faults on device 07 display as “107”).
Select “1” if using 2-
digit Fixed-
Word Display keypads (e.g., certain
6128 series keypads). If selected, ECP faults for all devices will display
as “91” on 2
-
digit displays, and “191” on 3
-
digit or Alp
ha keypads.
VISTA-
15P/20P/SIA Program
Guide
18
Configurable Zone Type Worksheet
Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data fields*182-
*185.
Configurable zone types 92 and 93 (VISTA
-20P only) can only be programmed using the downloader software.
Programming Configurable Zone Type options involves making 10 entries in data field *182 for zone type 90 and field *184 for zone type
91, where each entry represents the sum of the values of the various options shown in the tables below. Use fields *183 and *185 to
program Contact ID report codes for these zone types.
ENTRY 1
(See note 5 for RF
zones)
ENTRY 2
(See note 5 for RF zones)
Response when system disarmed and zone is:
Auto
Restore
Vent Zo
ne
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off
-
normal
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = normal
4 = alarm
8 = trouble
12 = fault
0 = normal
1 = alarm
2 = trouble
3 = fault
see note 6
0 = no
4 = yes
0 = no
8 = yes
E
ntry 1 = EOL + Open
Entry 2 = Short + auto restore + vent zone
ENTRY 3
(See note 5 for RF zones)
ENTRY 4
(See note 5 for RF zones)
Response when armed STAY and zone is:
Byp. when
disarmed
Byp. when
armed
Intact EOL
RF zone normal
Open
RF zone N/A
S
horted
RF zn off
-
normal
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = normal
4 = alarm
8 = trouble
12 = fault
0 = normal
1 = alarm
2 = trouble
3 = fault
see note 6
0 = no
4 = yes
0 = no
8 = yes
Entry 3 = EOL + Open
Entry 4 = Short + byp.
disarmed + byp. armed
ENTRY 5
(See note 5 for RF zones)
ENTRY 6
(See note 5 for RF zones)
Response when armed AWAY and zone is:
Dial Delay
(see field *50)
Fault Delay
(see field *87)
Intact EOL
RF zone normal
Open
RF zone N/A
Shorted
RF zn off
-
norma
l
0 = normal
1 = alarm
2 = trouble
3 = fault
0 = normal
4 = alarm
8 = trouble
12 = fault
0 = normal
1 = alarm
2 = trouble
3 = fault
see note 6
0 = no
4 = use delay
0 = no
8 = use delay
see note 1
Entry 5 = EOL + Open
Entry 6 = Short + dial
delay + fault delay
ENTRY 7
ENTRY 8
Display Faults
Power Reset/
Verification
Use Entry
Delay 1/2
Use Exit
Delay
Respond as
Interior Type
0 = show alarms
when armed
& disarmed
1 = don’t show
alarms when
armed
(show
alarms, trbles,
faults when
disarmed)
3 = never show
any alarms,
trbles, faults
0 = no
4 = power reset
after fault
(by code + OFF)
12 = verification
(see zone
type 16)
0 = no
1 = delay 1
2 = delay 2
0 = no
4 = use exit
delay
0 = no
8 = yes
see note 2
Entry 7 = fault display + power
reset/verification
Entry 8 = entry delay 1/entry delay 2 + exit delay +
interior zone type
ENTRY 9
ENTRY 10
Alarm Sounds
Use Bell
Timeout
Respond as
Fire Zone
Trouble
Sounds
Chime when
Chime Mode On
0 = none
1 = steady
keypad
2 = steady bell
and
keypad
3 = pulsing bell
and keypad
0 = no
4 = yes
see fields *32,
*33
0 = no
8 = yes
see zone type
09; see note 4
0 = none
1 = periodic
beep
2 = trouble
beeps
0 = no
4 = yes
Entry 9 = alarm sounds + bell timeout + fire zone
Entry 10 = trouble so
unds + chime
Entries for Fields *182 and *184
Entry
Zone Type 90
Zone Type 9
1
(field *182)
(field *184)
1
2
3
4
5
6
7
8
9
10
To calculate the value for each entry:
Simply add the values of the selected
options in each of the entry’s columns (one
option per column). For example, to program
Entry 2 for “alarm response
to short,” “auto
restore on,” but not a “vent zone,” enter 5
(“1” for alarm short + “4” for auto restore yes
+ “0” for vent zone no).
Zone Conditions Represented
in Entries 1-
6
NOTES:
1. Fault Delay: Do not use the “Fault Delay”
option with a configurable zone type if it
is set for an entry or exit delay, otherwise
unpredictable results may occur.
Fault Delay applies only to alarms and
troubles.
2. To create an interior type zone, select
“respond as interior zone type” (entry 8,
interior type = yes)
, and set zone
response to “fault” in entries 3-
4 to
ensure fault displays; do not set as
“normal,” “alarm,” or “trouble.”
3. Do not set fire zones to respond as a
“fault” (entries 1-
6), otherwise faults will
not display unless the [
∗
] key is pressed.
4. 4219/4229 modules must use EOLRs or
unpredictable results may occur.
5. RF Zones: The “open” option in entries
1, 3, and 5 is not applicable for RF
zones. Use the “intact EOL” option for
normal RF zone conditions and “shorted”
for off
-normal RF zone conditi
ons.
6. a. Zone-
Doubling/Double-
Balanced: A
short on either zone of a zone-
doubled
pair or on a double-
balanced zone
causes a tamper condition.
b. For double-
balanced zones, this entry
must be “0.”
c. For zone-
doubled zones,
both
zones
of the doubled pai
r must be assigned
the same response to a short.
VISTA-
15P/20P/SIA
Program
Guide
19
∗
56 Z
one Programming Menu Mode
Press
*56
while
in
Data Field Program
min
g.
There is a
Zone Programming Worksheet is on page 43.
Zones and Partitio
ns
Each protection zone needs to be programmed with various attributes using *56 Zone Programming mode or
Q
58 Expert Programming
Mode.
Using this mode, enter the zone number to be programmed and make appropriate entries at the prompts. Finally, Confirm the serial
number of wireless transmitter zones.
The VISTA
-20P system can control two independent areas of protection (known as partitions) for use by independent users, if desired, by
simply assigning zones to one or the other partition during zone programm
ing. The VISTA
-20P, by default, automatically distributes users
between the two partitions. The master user can change the user number distributions.
Zones can also be assigned to a common partition, which is an area shared by users of both partitions (such as a lobby in a building). This
allows either partition to arm, while leaving the common partition disarmed for access into the other partition. The following describes the
functioning of the VISTA
-20P common partition:
• The common zone sounds and reports alarms only when both partitions are armed. If only one partition is armed, the system ignores
faults on the common zone.
• Either partition may arm its system if the common zone is faulted, but once armed, the other partition will not be able to ar
m u
nless the
common zone is first bypassed or the fault is corrected.
• Faults on the common zone are displayed on common zone keypads, and will also appear on another partition’s keypad when that
partition is armed.
• Either partition can clear and restore t
he common zone after an alarm.
∗
56 Menu
Mode
PROMPT
VALID ENTRIES
EXPLANATION
SET TO CONFIRM?
0 = NO 1 = YES 0
Confirm?
0 = no
1 = yes
[
∗
] to continue
This display appears upon entry into this mode.
The default is 0 (No).
If 1 (Yes) is entered, you will be prompted to confirm each
transmitter after entering the serial and loop numbers (at the
“XMIT TO CONFIRM” prompt later).
Enter Zn Num.
(00 = Quit)
10
Zone Number
VISTA-
20P:
wired
01-
08 (and 09-
48
†
); wireless
09-
48; RF button zones 49
-64
VISTA-
15P:
wired 01-
06 (and 09
-24
†
); wireless
09-
34; RF button zones 49-
56
Both Controls:
91 = addr. device report enable
92 = duress report enable
95, 96, 99 =
emerg. zones
[
∗
] to continue
00 to quit
Enter the zone number that you wish to program
. Zone 10
has been entered in the example display at left.
Enter a report code for zone 91 to enable addressable
device reporting.
Enter a report code for zone 92 to enable duress reporting.
95, 96, 99 are emergency (panic) key zones.
† if zone expanders
are used.
Zn
ZT
P RC
In:
L
10
00
1 10 RF: 1
Summary Screen
[
∗
] to continue
“IN: L” appears for wireless zones and indicates input type and
loop.
“IN: AD” appears for hardwire expansion zones (AW) and indicates
the module’s address (AD
), which is based on the zone number.
“HW: RT” appears for hardwire zones and indicates configuration
(EOL, NO, NC, zone doubling, double-
balanced) and response time
selection.
10 Zone Type
Perimeter
03
Zone Type (ZT)
See table
at right
.
Each zone
must be assigned to a
zone type, which defines the way
in which the system responds to faults in that zone. Enter the Zone
Type code from the list below:
Note:
If 00 is entered,
Delete Zone ?
will be displayed.
00 = Not used
07 = 24-
Hr Audible
20 = Arm
–STAY*
01 = Entry/exit #1
08 = 24-
Hr Aux
21 = Arm
–AWAY*
02 = Entry/exit #2
09 = Fire
22 = Disarm*
03 = Perimeter
10 = Interior w/Delay
23 = No Alarm
Resp
04 = Interior Follower
12 = Monitor Zone
24 = Silent
Burglary
05 = Day/Night
14 = C
arbon Monoxide
77 = Keyswitch
06 = 24-
Hr Silent
16 = Fire w/Verify
*5800 button
-
type transmitters only
10 Partition
1
Partition No. (P)
(VISTA-
20P)
1-3 = partition
(3 = common)
[
∗
] to continue
Enter the
Partition number for this zone. Partition 1 is shown
entered.
VISTA-
15P/20P/SIA Program
Guide
20
*56 Zone Programming Menu Mode
(Continued)
10 Report Code
1st 01 2nd 00
10
Report Code (RC
)
First Digit:
1-9, 10 for 0, 11 for
B, 12 for C, 13 for D, 14 for E,
15 for F
00 to disable
Second Digit: same as above
[
∗
] to continue
Enter the report code for this zone, which consists of 2
hexadecimal digits, each in turn consisting of 2 numerical digits.
For example, for a report code of “10,” enter
01
and
00
.
For Contact ID
®, e
ntering any
non-
zero entry as the first digit
enables the report code for this zone.
02 HARDWIRE TYPE
EOL
0
Hardwire Type
0 = EOL
1 = NC
2 = NO
3 = z
one doubling
(ZD)
†;
4 = d
ouble
-balanced (DB)
†
[
∗
] to continue
This prompt appears only for zone numbers 02
-
08
.
Zone 1 is automatically set for EOL operation.
† VISTA-
20P
02 Response Time
1
Response Time (RT)
0 = 10mSec;
1 = 350mSec
2 = 700mSec
3 = 1.2 seconds
[
∗
] to continue
Appears only for hardwire
zones 01
-
08 (zone 02 is the display
shown).
Option 3:
used for “clean me” option on zone 1 (see field
∗
174).
NOTE:
If zone doubling is being used, the response time
selected for zones 02-
08 automatically applies to each zone’s
associated doubled zone.
10 INPUT TYPE
RF TRANS
3
Input Device type (In)
2 = AW (Aux wired zone)
3 = RF (supervised RF
transmitter
4 = UR (unsupervised RF
transmitter)
5 = Button type RF
transmitter
(unsupervised).
[
∗
] to continu
e
This prompt is skipped for zones 2
-
8, or 2
-
16 if zone
-
doubling
was enabled at “Hardwire Type” prompt.
All of the RF transmitters have one or more unique factory
-
assigned input (loop) ID codes. Each of the inputs requires its
own programming zone
(e.g., a
583
4-4's four inputs require four
programming zones).
RF Transmitters can be enrolled as one of the following types:
Type
Description
RF
(Supervised RF)
Sends periodic check
-
in signals, as well as
fault, restore, and low
-battery signals. The
trans. must stay within receiver's range.
UR
(Unsupervised RF)
Sends all the signals that the “RF”
type
does, but the control does not supervise
the check
-in signals. The transmitter may
therefore be carried off
-
premises.
BR
(Unsupervised
Button RF)
Sends only fault signals. It will not send a
low
-battery signal until it is activated. The
transmitter m
ay be carried off
-
premises.
NOTE:
•
For the built
-in hardwired zones, the Input Device type is
automatically displayed as HW and cannot be edited.
•
To change the input type of a previously programmed
wireless device (type RF, UR, BR) to a wired zone (t
ype AW),
you must first delete transmitter’s serial number (see To
Delete A Serial Number prompt)
VISTA-
15P/20P/SIA
Program
Guide
21
*56 Zone Programming Menu Mode
(Continued)
10 INPUT S/N:
L
A022-
4064
1
Input Serial number
and
Loop Number
[
∗
] to continue
Used only
when enrolling
wireless transmitters.
Enroll the transmitter’s serial number and loop number as follows:
1. a. Transmit two open/close sequences (for button-
type trans, press
and release the button twice, waiting about 4 secs before pressing
the button the second time).
OR
b. Manually enter the 7-
digit serial number printed on the label of the
transmitter. Press the [
∗
] key to move to the “L” position, then
enter the loop number.
Use the [A] (Advance) and [B] (Back) keys to move the cursor
forward and back within the screen. Pressing the [C] (Copy) key
will insert the previously enrolled serial number, if desired (used
when programming a transmitter with several input loops).
To delete an existing serial number, enter 0 in the loop number
field. The ser
ial number will change to 0's. If 0 was entered in
error, simply re
-enter the loop number or press [#], and the
serial number will return to the display.
2. Press [
∗
] to continue. The system now checks for a duplicate
serial/loop number.
If no duplicate i
s found, the display shows the serial number and
loop number.
3.
Press [
∗
] to continue to confirmation screen
.
10 INPUT S/N
L
A022-
4064
?
Loop Number Change
[
∗
] to continue
NOTE:
If the [C] key is used to copy the previously enrolle
d
serial number, the cursor will move to the Loop column (L) with
the previous serial number displayed, and display a highlighted
question mark for the loop number.
Enter the loop number and press [
Q]. The system will now
check for a duplicate serial/loo
p number combination.
XMIT
TO
CONFIRM
PRESS
Q
TO SKIP
Confirmation Option
[
∗
] to continue
This prompt will only appear if you answered “Yes” at the first
prompt in this section.
The system will enter a confirmation mode so that the operation
of the
actual programmed input can be confirmed.
Activate the loop input or button that corresponds to this zone.
Entd A022-
4063 1
Rcvd A022-
4064
1
If Serial or Loop
Numbers do not match
after activating the
transmitter
[
∗
] to continue
If the serial num
ber transmitted does not match the serial
number entered, a display similar to the one shown appears. If
the loop number does not match, it will also be displayed.
If so, activate the loop input or button on the transmitter once
again. If a match is not obtained (i.e., summary display does
not appear), press the [#] key twice and then enter (or transmit)
the correct serial number.
10 INPUT S/N:
L
A000-
0000
0
To Delete a Serial No.
0 =
delete serial number
# = undo deletion
[
∗
] to
continue
To delete an existing serial number, enter 0 in the loop number
field. The serial number will change to 0's.
If 0 was entered in error, simply re-
enter the loop number or
press [#], and the serial number will return to the display.
Zn
ZT
RC
In:
L
10
03
10
RF:
1s
Summary Screen
[
∗
] to continue
If the serial number transmitted matches the serial
number entered, the keypad will beep 3 times and a
summary display will appear, showing that zone's
programming. Note that an “s”
indicates that a
transmitter’s serial number has been enrolled.
Press [
∗
] to accept the zone information and continue.
PROGRAM ALPHA?
0 = NO 1 = YES 0
Alpha Descriptors
0 = no
1 = yes
[
∗
] to continue
If you want to program descriptors for zone
s now, enter 1 (Yes)
and refer to the
∗
82
Descriptor Programming section for
available descriptors
.
ENTER ZN NUM.
(00 = QUIT)
11
Next Zone Number
[
∗
] to continue;
00 = quit
If 0 (No) was entered above, the system will return you to the
ENTER ZN NUM
. prompt for the next zone.
When all zones have been programmed, enter 00 to quit
VISTA-
15P/20P/SIA Program
Guide
22
∗
58 E
xpert Zone Programming Menu
Mode
Press
*58 while in
Data
Field
Programming
This method is designed for use by installers with previous experience in programming
this
control panel
. This mode is also
used to program wireless keys using pre-
defined templates.
SET TO CONFIRM?
0 = NO 1
= YES 0
Confirm?
0 = no; 1 = yes; [
∗
] to
continue
Select whether you want confirmation of wireless device
enrollment. (See “XMIT TO CONFIRM” prompt later in this
section.)
We recommend that you confirm the programming
of every transmitter.
If
1
(Yes) i
s entered, you will be prompted to confirm each
transmitter after entering the serial and loop numbers (at the
“XMIT TO CONFIRM” prompt later).
Zn ZT P RC HW:
RT
01 09 1 10 EL 1
Summary Screen
01-
64 = zone number;
[
∗
] to continue;
00 = quit
[D] to go to prompts for
wireless key programming
templates
A summary screen appears, showing
zone 1’s currently
programmed
values.
Enter the zone number being programmed, then press [
∗
],
which displays a summary screen for that zone
and the c
ursor
moves to the Zone Type location. The cursor then automatically
moves to the next locations after each entry is made.
If programming a wireless key,
press the [D] key then skip to
the Wireless Key Programming Templates section following this
section.
When [D] is pressed, you can choose from a series of
preset templates for easy programming of wireless key zones.
When all zones have been programmed, press
00
at this
prompt to quit this menu mode.
Zn
ZT P RC IN:
L
10
00
1 10 RF
1
Zone Programming
ZT =
see Zone Type chart
shown in *56 Menu
Mode “Zone Type”
prompt
P =
partition 1, 2, 3
(common);
RC = 1 (send CID report); 0
(no report)
IN =
input type;
L =
loop number
[
∗
] to continue
A summary screen with the selected zone’s curren
t
programming appears.
Begin programming zone information as follows:
•
Enter Zone Type (ZT), Partition (P), Report Code (RC; 0-
9
only; use *56 mode to enter hex codes), and Input Device
Type (IN)* sequentially, but not the Loop No. (L).
•
Use the [A] (Advance) and [B] (Back) keys on the keypad to
move the cursor within the screen.
•
Use the [C] key to copy the previous zone’s attributes.
Press [
Q] to save the programming and continue to the serial
number/loop number prompt. If needed, you can press the [#]
key to back up without saving.
* If HW (hardwired) or AW (Auxiliary) is entered for Input
Device Type, the next screen will be similar to the
prompt
shown, except that HW or AW will be displayed under “IN”.
If RF, BR, or UR is entered, a prompt for Serial and Loop
number will be displayed, as
described in
∗
56 Menu mode
section.
When done, the display returns to the initial summary screen
prompt
to let you program the next zone.
To exit this mode,
enter 00 at the Summary Screen prompt.
VISTA-
15P/20P/SIA
Program
Guide
23
Wireless Key Templates
Press the [D] key from *58 Menu mode Summary Screen
This procedure programs the wireless keys,
bu
t a key is not active for arming/disarming until it is assigned to a user
number
(see
System Operation
section, Assigning Attributes Command in the
User Guide).
TEMPLATE
?
1–6
1
Template Number
1–6 = templates
•
Enter
Template number 1
–
6 (see chart on next page).
See the defaults provided for each template in the chart that
follows these procedures.
•
Select from templates. Press [
∗
] to display template (1
shown selected).
NOTE
: If necessary, press [#] to back up
and re-
enter
template number.
•
Press [#] if you want to return to *58 Menu mode summary
screen.
L 01 02 03 04
T 23 22 21
23
Template Display
•
When [
∗
] is pressed, the selected template will be displayed.
Top line of display
represents loop numbers; bottom line
represents zone type assigned for each loop.
•
Press [
∗
] to accept template.
PARTITION
1
Partition
VISTA-20P. 1 = partition 1;
2 = partition 2
•
Enter the partition in which the key is to be active, then
press [
∗
] to continue.
ENTER START ZONE
00 = QUIT
36
Start Zone Number
•
The system will search for the highest available consecutive
4-zone group (the four zones in the case of the
5804BD),
and display the lowest zone number of the group.
If yo
u want to start at a different zone, enter the zone
desired, and press [
Q]. If that zone number is displayed, the
system has the required number of consecutive zones
available, beginning with the zone you entered. If not, the
system will again display a suggested zone that can be used.
If the required number of consecutive z
ones is not available
at all, the system will display “00”.
To quit this mode
and return to *58 Menu mode, enter 00
at this prompt.
•
Press [
∗
] to accept.
INPUT S/N L
AXXX-
XXXX
–
Serial Number
•
Manually enter the serial numb
er printed on the label for the
wireless key or press and release the button to transmit its
serial number.
•
Press [
∗
] to accept the serial number. The system will check
for a duplicate.
•
If necessary, press the [#] key to back up without saving,
and re-
enter the serial number.
•
Use the [A] key to move forward within the screen, and the
[B] key to move backward.
XMIT TO CONFIRM
PRESS
Q
TO SKIP
Confirm
[
∗
] to continue
•
If “Yes” was entered at the
SET TO CONFIRM?
prompt
previously (see first prompt following entry into the
∗
58
Expert Programming Mode), the display on the left will
appear. Confirm serial and loop numbers by activating the
wireless key.
IMPORTANT:
When confirmed, the key is not active for arming/disarming until
it is assigned to a
user number (using the assigning attributes
command, attribute “4”). See
System Operation
section for
procedure.
VISTA-
15P/20P/SIA Program
Guide
24
Wireless Key Templates
(Continued)
Entd A022-
4063
Rcvd A022-
4064
Not Confirmed
[
∗
] to continue
If the serial number transmitted do
es not match the serial
number entered, a display similar to the one shown will appear.
If the loop number does not match, it will also be displayed.
If so,
activate the button on the wireless key once again. If a
match is not obtained (i.e., summary displ
ay does not appear),
press the [#] key and then enter the correct serial number.
If the serial number transmitted matches the serial number
entered, the keypad will beep 3 times and will return you to the
Zone Number prompt to enter the starting zone for t
he next
wireless key.
Or you can return to *58 Menu mode by pressing 00 at the
Zone Number prompt.
Wireless Key Predefined Default Templates
5834-4 Wireless Key
Transmitter
NOTE:
Some
transmitters are not intended for use in UL installations.
For
Button
-Type Devices
For
Button
-Type Devices
TEMPLATE 1
Loop
Function
Zone Type
TEMPLATE 4
Loop
Function
Zone Type
1
No Response
23
1
No Response
23
2
Disarm
22
2
No Response
23
3
Arm Away
21
3
Arm Away
21
4
No Response
23
4
Disarm
22
TEMPLATE 2
Loop
Function
Zone Type
TEMPLATE 5
Loop
Function
Zone Type
1
No Response
23
1
No Response
23
2
Disarm
22
2
Arm Stay
20
3
Arm Away
21
3
Arm Away
21
4
Arm Stay
20
4
Disarm
22
TEMPLATE 3
Loop
Function
Zone T
ype
TEMPLATE 6
Loop
Function
Zone Type
1
24-
hour audible
7
1
24-
hour audible
7
2
Disarm
22
2
Arm Stay
20
3
Arm Away
21
3
Arm Away
21
4
Arm Stay
20
4
Disarm
22
Deactivating & Removing a Wireless Key from the System
Deactivate a wireless key by
deleting the associated user code:
Delete the User Code:
Master code + [8] + 2-
digit user no. + [#] [0]
Remove a wireless key from the system by deleting
one of the
wireless key zones
using
Zone
Programming
mode:
1.
Press *56 while in Program mode then enter a zone number assigned to the wireless key.
2.
Scroll through each prompt by pressing [
∗
] until the
Input S/N
prompt
appears
.
3.
Enter 0 for the loop number
and press [
∗
].
4. Exit program mode.
VISTA-
15P/20P/SIA
Program
Guide
25
∗
57 F
unction Key Menu Mode
Press
∗
57 while in Data
Field
Programming
.
The Function Key Worksheet is on page
45.
The system provides the ability to program each of the four keypad function keys to perform one of 12 system oper
ations.
The end user can then activate the function by simply pressing and holding the programmed key for 2 seconds. Typical
functions (listed below) include single-
button arming, turning lights on/off, or single-
button paging.
To assign emergency key functions (function key option “00”), first program the respective emergency zone number (95 for
“A” key, 96 for “C” key, 99 for “B” key) with the desired zone type using
∗
56 (or
∗
58) Zone Programming mode, then use
∗
57
Function Key menu mode to assign the desired key.
To use a function key to activate a relay action (
∗
57 Menu mode key function 07), use
∗
79 Menu mode to map the output, and
use
∗
80 Menu mode to define the output’s action; select system operation type “66.”
To use a function key for a user macro, use
∗
57 menu mode to activate the desired key, then define the actual macro
functions using the user code + [#] + [6] [6] command.
Press Key to Pgm
0 = Quit
0
Function Key
Press the desired function
key, A
-D.
[
∗
] to continue
0 = Exit this mode
P
ress the desired function key (A
-
D) you want to program.
NOTE:
A key programmed as a function key is no longer
available to be used as an end-
user macro key or panic key.
Partition
1
Partition Number
(VISTA
-20P)
1 = partition 1
2 = partition 2
3 = common partition
[
∗
] to continue
Enter the partition in which the function key is active.
Key "A" Func
Zone 95
00
Define Key Function
00-
12 = see list at right
[
∗
] to continue; returns to
key number prompt with the
next function key letter
displayed
Enter the desired function for this key, 00 to 12, from the
options listed. (00 selected for example display shown at left).
Press [
∗
] to returns to key number prompt with the next function
key letter displayed.
00
†
= For the Function key selec
ted, the functions are predefined as
follows:
If A selected = Zone 95 (emergency key, same as [1] [
∗
] pair)
If B selected = Zone 99 (emergency key, same as [
∗
] [#] pair)
If C selected = Zone 96 (emergency key, same as [3] [#] pair)
If D selected = Single-
button paging
01 =
Single-
button paging (sends a 999-
9999 message to pager)
02 =
Display time
03 =
Arm AWAY (reports as User 00 if closing reports are enabled)
04 =
Arm STAY (reports as User 00 if closing reports are enabled)
05 =
Arm NIGHT
-STAY (re
ports as User 00 if closing reports enabled)
06 =
Step Arming (arms STAY, then NIGHT
-STAY
†††
, then AWAY)
07 =
Output Device Command (for device programmed as system
operation type 66–
function key in *80 Menu Mode)
08 =
Communication Test (sends Contact ID code 601)
09 =
Macro Key 1 (define macro by user code + [#] [6] [6] command)
10 =
Macro Key 2 (define macro by user code + [#] [6] [6] command)
11
††
= Macro Key 3 (define macro by user code + [#] [6] [6] command)
12
††
= Macro Key 4 (define macro by user code + [#] [6] [6] command)
† System defaults to these function key settings.
†† Macros 11-
12 apply to VISTA
-20P only.
††† If Night
-
Stay zones are listed in zone list 5
VISTA-
15P/20P/SIA Program
Guide
26
Output Device
Programming Gene
ral
Info
(*79/*80 Menu Mode)
Output Devices:
The VISTA-
20P system supports up to 16 relays and/or Powerline Carrier devices (X
-10 devices)
plus 2 built
-in trigger outputs in any combination. These 18 “outputs” are assigned to system
-wide
output numbers (01-
18). Use *79 Menu Mode to assign output numbers and map them to device
addresses.
The VISTA-
15P supports 8 relays and 2 built
-in trigger outputs (total 10 outputs).
Output Functions:
The system also provides installer
-defined output functions, which can
be assigned to any of the
physical outputs. Therefore, the action of any one of the outputs can be based on as many of these
defined functions as desired. This lets a single relay or X
-10 device perform many functions.
The control supports: V20P = up to
48 defined functions; V15P = up to 24 functions
Use *80 Menu Mode to define output functions.
WARNING:
Relays and output devices are not recommended for life safety applications.
NOTE:
When navigating the *79 and *80 menus: The [
Q
] key is used to accept
an entry and advance to
the next prompt. The [#] key is used to
go
back to the last question to check or change an entry. Press [
Q
]
to go forward again.
Programming Output Devices
1. Use *79 Menu Mode to assign module and output numbers and map them to device addresses.
NOTE:
You must map output devices using *79 Menu Mode
before
you can use *80 menu Mode.
2. Use *80 Menu Mode to create output definitions, which control the output devices, if desired.
3. Use *81 Zone List Menu mode to define zone
lists for use with output devices if the device action is based on more than
one zone.
•
To program a device for manual activation (user code + [#] [7] / [#] [8] + 2-
digit device number) or for scheduled automatic
activation, simply map the device using *79 Menu mode.
•
To program a device to automatically activate upon a system event (or function key), use *79 Menu mode to map the
device, then use *80 Menu mode to define the automated device action.
*79 Relay/X
-10
Menu Mode
Press
∗
79 while in
Data Field
Programming
.
The *79 Device Mapping Worksheet is on page
46.
Use this menu to assign Relay Module device addresses and specific relay num
bers, and Powerline Carrier unit numbers. The
system is based on predefined module addresses for 4204 and 4229 modules. Refer to the table shown at the “Module
Address” prompt on the next page and set the modules’ addresses (via module DIP switches) accordingly.
The following table shows how these outputs are identified.
Output Identification
This output...
is identified by...
Relays
the Relay Module’s device address and the relay position on that module (i.e. the physical relay
number, 1
-
4, on that module).
X
-
10 Device
a house ID (entered in data field *27) and the unit number of the device.
Built
-
in Outputs
the output number assigned, 17 for Trigger 1 and/or 18 for Trigger 2.
ENTER OUTPUT NO.
00 = QUIT
xx
Device Output Number
VISTA-
20P:
01-
16 = relays/X
-10
17, 18 = on-
board triggers
VISTA-
15P:
01-
08 = relays/X
-10
17, 18 = on-
board triggers
[
∗
] to continue
00 to quit
This is the logical (or reference) relay number as used in the
system. Relays and X
-10 devices are numbered 01-
16; the on-
board triggers are numbered 17 and 18 and can be
programmed for inverted output, if required.
VISTA-
15P/20P/SIA Program
Guide
27
79 Relay/X
-10
Menu Mode
(Continued)
17 OUT NORM LOW
0 = NO 1 = YES
0
Output Normally Low
0 = no (standard default)
1 = yes
[
∗
] to continue
(p
rompt appears only
if t
rigger 17
or
18
was selected above
)
Selecting
0
(no) sets the output level normally high (default
setting).
Selecting
1
(yes) sets the output normally low.
Output Trigger 17 can be used for resetting 4-
wire smoke
detectors
†
by connecting it to the negative power terminal of the
smoke detector, selecting 1 at this prompt, and setting as zone
type 54, fire zone reset, in *80 Menu mode.
After entry, display returns to Output Number prompt. Use *80
Menu mode to program the function of the trigger.
†
Power
Reset:
This control does not automatically reset power
to 4-
wire smoke detector zones, so you must use a relay
(e.g., 4204, 4229) or on-
board trigger to reset power (also
required for fire verification).
XX OUTPUT TYPE
DELETE
0
Output Type
0 =
delete
1 = relay on 4204/4229
2 = Powerline Carrier
Device
[
∗
] to continue
Select whether this is a relay or a Powerline Carrier (X
-
10)
device.
If Powerline Carrier
Device
(X-10)
is selected, go to “A” prompt.
If relay is selected, skip to “B” prompt.
“A”
XX UNIT No.
yy
Unit Number
01-
16 = predefined address
[
∗
] to continue
(p
rompt appears
if X
-
10 is selected)
Enter the unit code (set at the device) and press [
∗
].
The system returns to the Output Number prompt.
“B”
XX MODULE ADDR
07-
15
yy
Module Address
07-
15 = predefined address
[
∗
] to continue
REMOTE SERVICES NOTE:
If
using the communication
device’s Multi
-Mode
4204 or 2-
4204 options
, select one of the
4204 addresses, though a
physical 4204 module is not
installed. If using 2-
4204 multi-
mode option, the second 4204
address is automatically one
number higher than the first
address
. Make sure these
addresses are not used by
physical 4204 modules that may
be installed.
See
the
communication device’
s
instructions
to enabl
e Multi
-
Mode.
(p
rompt appears
if relay is selected)
Enter the predefined address for this module as listed below.
Make sure the module’s DIP
switches are set to the selected
address.
Module Addresses
Address
Module
07
1st 4229 (with zones 09-
16)
08
2nd 4229 (with zones 17-
24)
09
†
3rd 4229 (with zones 25-
32)
10
†
4th 4229 (with zones 33-
40)
11
†
5th 4229 (with zones 41-
48)
12
1st 4204
13
2nd 4204
14
†
3rd 4204
15
†
4th 4204
† These addresses apply to VISTA
-20P only.
XX REL POSITION
1-4
zz
Relay Position
1-4 = relay position
[
∗
] to continue
This is the actual (or physical) relay number with respect to the
Relay Module upon which it
is located. For 4204 modules, relay
numbers are 1-
4. For 4229 modules, relay numbers are 1-
2.
The system returns to the Output Number prompt for
programming the next device.
REMOTE SERVICES NOTE:
If using
the communication
device’s
multi
-mode, program
virtual 4204
relays to trigger on
those system events
intended
to be sent to the user’s email
address.
(4204 option = up to 4 events; 2-
4204 option = up to 8
events)
VISTA-
15P/20P/SIA Program
Guide
28
∗
80
Output Function Menu Mode
Press
∗
80 while in
Data Field
Programming
.
The Output Definition Worksheet is on page
47.
Use this mode to program output function definitions (up to 48 functions) that provide automated control of any of the output
devices, based on events occurring on individual zones or zones with certain zone types.
Each output definition is identified
by an output function number, and includes the following components:
Output Definition Components
Component
Description
Output Function No.
A re
ference number that defines an output’s characteristics.
Activated By
Determines whether the initiating event occurs on a zone, a zone list, or a zone type.
Event
Event that triggers the output action. Can be an event occurring on a specific zone number
or a zone list, or a
specific zone type.
Partition
If the output is activated by zone type, this defines the partition in which the programmed event is to cause the
device action.
Output Action
Defines the action of the relay/X
-
10 device when the defined
event occurs. Can close for 2 seconds, stay
closed until reset, continuously pulse (1-
second close-
open-
close
-open, etc.), toggle the device state, or
activate for a defined duration (set in data field *177).
Output No.
Assigns this function to a specifi
c output number (defined in *79 Menu Mode). This is the output number that
will perform this function upon the triggering event. Note that each defined function is associated with only one
output number. This means that if more than one output device needs
to perform this particular function, you
need to define another output function number with the same attributes, but assign the appropriate output
number. (i.e. output devices can be assigned more than one function number, but each function number can
onl
y be assigned a single output number.
For example,
if you want to pulse a strobe light upon fire alarms on zone 4 using a relay mapped to output number 2 (as
programmed in *79 Menu Mode), program the following in *80 Menu Mode:
Prompt
Entry
Output Funct.
#
=
01 (assuming this is the first output function)
Activated By:
=
3 (zone number)
Enter Zn No.
=
04 (requires 2-
digit zone numbers)
Output Action
=
3 (continuous pulse)
Output Number
=
02 (device mapped in *79 Menu Mode)
Output Funct.
#
(00 = Quit)
01
Output Function No.
(VISTA-
20P: 01-
48
(VISTA-
15P: 01-
24)
[
∗
] to continue; 00 to quit
Enter the output function number to be defined (or 00 to exit)
01
A E P Trig
?00 0 0
– ZL=00
Summary Screen
[
∗
] to continue
Thi
s screen displays a summary of the current output
programming (for this example, Zone List has been selected-
this
is the default screen).
A
= Output Action;
E
= Triggering event;
P
= Partition;
Trig
= Trigger type
NOTE:
A question mark in the summary sc
reen indicates that the
device number shown has not been mapped. Use *79 Menu mode
to map the device.
01 Activated By:
Zone List
Activated By
0 = delete
1 = zone list (go to “A”)
2 = zone type
(go to “B”)
3 = zone number (go to “C”)
[
∗
] to continue
Select where the initiating event for this output definition is to occur as
follows:
If you enter “0,” the following prompt appears:
Delete?
0 = NO,
1 = YES
Press 1 to delete this output definition. The system deletes the output
function and any previ
ous programming.
A
”
01
Zn List
1
Zone List
01-
08 = zone list
[
∗
] to continue
(p
rompt appears
if zone list was selected)
Enter the desired zone list number associated with this output number.
At
the ENTER EVENT prompt, enter the zone list event that will activate this
output
NOTE:
Do not use pager zone lists 09-
12 in output definitions.
Enter Event
0 = restore; 1 = alarm;
Alarm
1
2 = fault; 3= trouble
NOTE:
For alarm, fault, and trouble, an event on ANY zone in the list
activates the output, but ALL zones in the list must be restored before the
output is restored.
Press [
Q
] to continue and skip to the “Output Action” prompt.
VISTA-
15P/20P/SIA Program
Guide
29
80 Output Function Menu Mode
(Continued)
“
B
”
01
Enter Zn type
Perimeter
03
Zone Type
See list at right for avai
lable
zone types.
(p
rompt appears
if zone type was selected)
Enter the desired zone type associated with this output number.
At the PARTITION prompt, enter the partition in which this zone
type will occur.
CHOICES FOR ZONE TYPES:
00 = Not Used
06 = 24 Hr S
ilent
14 = Carbon Monoxide††
01 = Ent
ry/Exit #1
07 = 24 Hr Audible
16 = Fire w/verification
02 = Ent
ry/Exit #2
08 = 24 Hr Aux
23 = No Alarm Response
03 = Perimeter
09 = Fire
24 = Silent Burglary
04 = Interior Follower
10 = Interior w/Delay
77 = Keyswitch Zone
05 = Day/Night
12 = Monitor Zone
90-
91 = Configurable
CHOICES FOR
SYSTEM OPERATION:
20 = Arming–
Stay
38 = Chime
54 = Fire Zone Reset
21 = Arming–
Away
39 = Any Fire Alarm
58 = Duress
22 = Disarming
40 = Bypassing
66 = Function Key†
31 = End of Exit Time
41 = **AC Power Failure
67 = Bell Fail
32 = Start of Entry Time
42 = **System Battery Low
68 = Telco Line Cut
33 = Any Burglary Alarm
43 = Comm. Failure
78 = Keyswitch Red LED
36 = **At Bell Timeout***
52 = Kissoff
79 = Keyswitch Green LED
** Use 0 (Any) for Partition No. (P) entry.
*** Or at Disarming, whichever occurs earlier.
† Use *57 Menu Mode to assign the function key (
function “07”).
††
when used with an output function, the carbon monoxide zone type
activates upon CO alarms only. Does not activate for trouble conditions.
Note:
In normal operation mode:
Code + # + 7 + NN Key Entry
starts
Device NN.
Code + # + 8 + NN Key Entry
stops
Device NN.
Enter the partition in which this zone type will occur.
01 Partition
0 = any partition; 1 = partition 1;
Any partition
0
2 = partition 2; 3 = common
Press [
Q
]
to continue and skip to the “Output Action” prompt.
“
C
”
01
Enter Zn No.
12
Zone Number
Press [
Q
] to continue.
(p
rompt appears
if zone number was selected)
Enter the desired zone number associated with this output
number.
At the ENTER EVENT pr
ompt, enter the zone event
that will activate this output.
01 Enter Event
0 = restore; 1 = alarm/fault/trouble
Restore
0
Press [
Q
] to continue to the “Output Action” prompt
01 Output Action
Close for 2 sec
1
Output Action
0 = off
1 = Close for 2 s
econds
2 = Stay Closed
3 = Pulse on & off (1 sec ON, 1
sec OFF)
4 = Change Device State
5 = Duration 1 (see data field
*177)
6 = Duration 2 (see data field
*177)
Press [
Q
] to continue.
Enter the desired device action.
Enter Output No.
R02
02
Output
Number
01-
16 = VISTA-
20P output
s
01-
08 = VISTA-
15P output
s
17-
18 = on-
board triggers
Press [
Q
] to continue.
Enter the device output number (programmed in *79 Menu
Mode) you want associated with this output.
02
A E P TRIG
R02 1 1 3
ZL=00
Summary Screen
Press [
Q
] to continue.
A summary screen appears showing the programmed settings.
Press [
∗
] to return to OUTPUT FUNCTION NUMBER prompt
VISTA-
15P/20P/SIA Program
Guide
30
∗
81
Zone List Menu Mode
Press *81 while in
Data Field
Programming
.
The Zone List Worksheet is on page
46.
Zone lists let you group individual zones for use with certain system actions.
Using this mode, simply
select an appropriate
zone list number, then add the desired zone numbers to
be included in that list.
The following table shows the available zone lists and their purposes:
List No.
Used for...
Notes
1, 2
general purpose (GP)
•
Any list may include any or all of the system's zone numbers.
•
A zone list can be assigned to more than
one output relay.
•
Zone List 4: When creating zone list 4 for cross zoning,
include only zones assigned to zone types 3, 4, or 5. Do not
include zones that have delays (entry/exit zones, interior
w/delay) or 24-
hour zones, as these zone types may produce
unpredictable operation and may not function as intended.
See field *85 for Cross Zone Timer option.
•
Zone List 6:
V20PSIA/V15PSIA
:
See field *50 for Dial Delay
Disable option.
•
Zone List 7:
V20PSIA/V15PSIA
:
See field *93 for Unlimited
Reports option.
3
chime
-
by
-
zone
(see field *26 to enable option)
4
cross zones (see note at right)
5
night stay zones
6
general purpose
V20PSIA/V15PSIA
: dial delay disable
7
general purpose
V20PSIA/V15PSIA
: unlimited reports
8
general purpose
9
zones that act
ivate Pager 1
10
zones that activate Pager 2
11
zones that activate Pager 3 (VISTA
-
20P)
12
zones that activate Pager 4 (VISTA
-
20P)
*81 Menu Mode
Zone List No.
(00 = Quit)
01
Zone List Number
01-
12 = zone list number
[
∗
] to continue
Enter the
Zone List Number to program (or 00 to quit). Press
[
Q
] to advance.
In the following displays, zone list 01 has been selected.
01
Enter Zn Num.
(00 = Quit)
00
Zone Number
01-
64
†
= zone numbers
followed by [
∗
] to
accept each zone
00 to continue
Enter
each zone number to add to the zone list, followed by
pressing [
Q
] (example, 01
Q
, 02
Q
, 03
Q
). After all zones are
entered, press 00 to continue.
IMPORTANT:
Do not include fire zones in zone lists that are
used to STOP device actions.
† VISTA
-
20P = 01
-
64; VI
STA
-
15P = 01
-
06, 09
-
34, 49
-
56.
01 Del Zn List?
0 = No 1 = Yes
0
Deleting Zone Lists
0 = don’t delete list
1 = delete this zone list
[
∗
] to continue
To delete the zone list, enter 1. All zones in the zone list will be
deleted automatically and the sy
stem returns to the Zone List
No. prompt.
To save the zone list, enter 0.
01 Delete Zone?
0 = No 1 = Yes
0
Deleting a Zone
0 = don’t delete zones
1 = go to next prompt to
delete zones
[
∗
] to continue
To save the zone list, enter 0 and the system r
eturns to the
Zone List No. prompt.
To delete a zone or zones in a zone list, enter 1 to continue.
01 Zn to Delete?
(00 = Quit)
00
Delete the Zone
01-
64
†
= zones to be
deleted from list
followed by [
∗
] to
accept each zone
00 to continue
Enter each z
one to be deleted from the list, followed by [
Q
].
After all zones to be deleted are entered, enter 00 to return to
the Zone List No. prompt so that another list can be
programmed, if desired.
† VISTA-
20P = 01-
64; VISTA-
15P = 01-
06, 09-
34, 49-
56.
VISTA-
15P/20P/SIA Program
Guide
31
∗
82
Alpha Descriptor Menu Mode
Press *82
while in
Data Field
Programming
.
The system lets you assign
zone descriptors for protection zones, keypad
panics, and RF receiver supervision faults. Each description can be composed of a combination of
up to 3
words
selected from
a vocabulary of words stored in memory (see
Alpha Vocabulary List page). In addition, up to 10 installer
-defined words can be
added to those already in memory, plus 3 additional words can be assigned as partition descriptors. Thus, when an alarm or
trouble occ
urs in a zone, an appropriate description for that zone's location can be displayed at the keypad.
Zone descriptors
are recommended for systems using Alpha display keypads, and
should be used if Voice keypads and touchscreens are
installed.
NOTE:
You can
also
enter zone descriptors when the zone is being defined in
Q
56 Menu mode.
If using
Voice keypads
and/or touchscreens
, select from those words in the Alpha Vocabulary List.
∗
82 Menu Mode
Program Alpha ?
0=No, 1=Yes
00
Program Alpha
0 = no
(quit Alpha mode)
1 = yes
[
∗
] to continue
The “Program Alpha ?” prompt will appear. Press 1 to continue.
Custom Words ?
0=No, 1=Yes
00
Custom Words
0 = no
1 = yes
The “Custom Words” prompt will appear.
Press 0 to program standard alpha descriptors from the fixed
vocabulary. The system then automatically display
s the
descriptor for zone 1.
Press 1 to define custom words (
see “Adding Custom Words”).
Q
ZN 01
Summary Screen
[
∗
] to continue
to edit mode
[#]
= return to Program
Alpha prompt (to quit)
Note that this is a “Summary mode,” and that no entries can be
made. Entries can be made only when the display contains a
flas
hing cursor, which signifies
Edit
mode.”
To exit the Alpha
Descriptor
mode, press
∗
+ 0 + 0 at the
summary display.
Q
ZN 01
Edit Mode
–
Flashing
Cursor
to edit = zone number then
[
∗
], then zone
number again
6 = save word and go to
next word in a
descriptor
8 = save descriptor and go
to next zone
[#] = return to Program
Alpha prompt (to quit)
Descriptor screen for zone 1 appears. To program a descriptor
(up to 3 words) for a zone, do the following:
1. Enter the desired zone number (existing descriptor, if any, is
displayed) and press [
∗
], then enter the zone number again to
start edit mode (flashing cursor appears).
2. a. Press [#] plus the 3-
digit number from the Alpha Vocabulary
List for the first word.
b. Press [6] to accept the word and move the cursor f
or the
next word in the descriptor.
3. Repeat steps 2a and 2b for the second and third words (if used)
4. When all words for that descriptor have been entered, press
[8] to save the descriptor for that zone. The summary screen
displays for that zone and t
he flashing cursor disappears.
5. Press [
∗
] at the summary screen and repeat steps 1-
4 to
assign a descriptor for the next zone.
6. When all descriptors have been entered, press [#]) at the last
descriptor summary screen to return to the PROGRAM
ALPHA? pr
ompt. Enter 0 (no) at the prompt to exit this mode
and return to Data Field mode.
VISTA-
15P/20P/SIA Program
Guide
32
*82 Alpha Descriptor Menu Mode
(Continued)
EXAMPLE:
(a)
Q
ZN 01
B
ACK
(b)
Q
ZN 01
BACK
(c)
Q
ZN 01
BACK
D
OOR
(d)
Q
ZN 01
BACK
DOOR
Descriptor Example
EXAMPLE: “BACK DOOR”
a. From the list, BACK = 013, so
, after entering the zone number
to be edited (step 1),
enter #013. If you accidentally enter the
wrong word, simply press [#] plus the correct 3-
digit number fo
the word you want.
b.
Press [6] to accept the selected word and continue to the next
word
. (if this is the only word you are using for the descriptor
press [8]
to save it)
.
c. Enter the 3-
digit number for the next word, “
DOOR,
” whose
number is “057.” Enter # 0 5 7.
d.
Because this is the last word in the example descriptor, press
[8] to save it. (If there was a third word in the descriptor, press
[6] to accept the selected word and continue to the
third
word.)
The summary screen displays with the select
ed descriptor.
Q
ZN 01
BACK
DOOR
Summary Screen
[
∗
] = to
enter another zone
number
[#] = return to Program
Alpha prompt (to quit)
The flashing cursor disappear
s
, indicating that the word(s) are
saved
for that zone, as shown in the summary display at the
left.
To enter
a descriptor for the next zone, press [
Q]
plus the
desired zone number. The summary display appears. Repeat
the previous steps to enter the descriptor for the zone.
Adding Custom Words (will not be annunciated by voice keypads or touchscreens)
You can
add
up to 10 installer
-defined words to the built
-in vocabulary, which can then be used when programming zone
descriptors. Each of the 10 words can
consist of a word string of one
or more words, but no more than
ten
characters can
be used for each word or word string.
When adding custom words, the keypad keys perform the following functions:
[4]
Moves cursor one space to the left.
[6]
Moves cursor one space to the right.
[8]
Saves t
he new word in the system's memory.
1. Select Custom Word mode (enter 1) when the prompt “CUSTOM WORD ?” is displayed.
2. Enter the number (01–
10†) of the custom word or word string to be created, corresponding to index numbers 245
- 254 respectively (for
example, if you are creating the first custom word or word-
string, enter 01, for the second, enter 02, etc.). A cursor will now appear at
the beginning of the second line.
† or 11, 12, 13 for partition 1, partition 2 and common lobby descriptors respectiv
ely. See Assigning Partition Descriptors paragraph
below.
NOTE:
Custom words 8, 9, and 10 are “reminder words” that are programmed using Scheduling Mode.
3. Refer to the Character List of letters, numbers, and symbols on a following page.
Press [#], foll
owed by the two-
digit entry for the first letter you would like to display (e.g., # 65 for “A”).
Press [6] to advance t
he cursor to the right, in position for the next character.
To delete a character,
simply enter the SPACE character (#32)
at the unwant
ed character’s location.
.
4. Repeat Step 3 to create the desired word(s). Note that the “4” key can be used to move the cursor to the left, if necessary. Remember,
no word or word-
string can exceed 10 characters
(except custom message/partition descriptor word numbers 11, 12, and 13, which can
be a maximum of 16 characters)
.
5. When the word is complete, press the [8] key to save the custom word(s) and return to the “CUSTOM WORD ?” display.
Repeat Steps 2–
5 for other custom words to be entered. To change a custom word, just overwrite it. When all words have been
programmed,
press [0] to return to the Descriptor entry. The custom word(s) will be automatically added to the built
-in vocabulary.
Assigning Partition/Custom Message Descriptors
VISTA-
15P: You can create a custom message display that appears on alpha keypads instead of “System Ready.” To assign a custom
message, use word number 11 as described below.
VISTA-
20P: You can assign a partition descriptor (up to 16 characters) for each partition plus the
common lobby. The system displays the
appropriate partition’s word instead of “DISARMED READY TO ARM.”
Use the same procedure as for adding custom words (described above), but use these word numbers in step 2:
11 = partition 1 ___________________________________________
12 = partition 2 ___________________________________________ (VISTA
-20P only)
13 = common lobby ________________________________________ (VISTA
-20P only)
Once a custom word is entered in any of these word locations (11-
13), the system d
isplays t
he appropriate partition’s word
instead of the default “DISARMED READY TO ARM” message VISTA-
15P/20P/SIA Program
Guide
33
*82 Alpha Descriptor Menu Mode
(Continued)
ALPHA VOCABULARY LIST (For Entering Zone Descriptors)
000
(Word Space)
– A –
• 001
AIR
• 002
ALARM
∗
004
ALLEY
005
AMBUSH
• 006
AREA
• 007
APARTMENT
• 009
ATTIC
∗
010
AUDIO
– B –
• 012
BABY
∗
• 013
BACK
∗
• 014
BAR
• 016
BASEMENT
∗
• 017
BATHROOM
∗
• 018
BED
• 019
BEDROOM
∗
020
BELL
• 021
BLOWER
• 022
BOILER
023
BOTTOM
025
BREAK
• 026
BUILDING
– C –
028
CABINET
• 029
CALL
030
CAMERA
031
CAR
033
CASH
034
CCTV
035
CEILING
036
CELLAR
• 037
CENTRAL
038
CIRCUIT
• 040
CLOSED
∗
• 046
COMPUTER
047
CONTACT
– D –
• 048
DAUGHTERS
049
DELAYED
• 050
DEN
∗
051
DESK
• 052
DETECTOR
∗
• 053
DINI
NG
∗
054
DISCRIMINATOR
055
DISPLAY
• 057
DOOR
∗
• 059
DOWN
• 060
DOWNSTAIRS
061
DRAWER
• 062
DRIVEWAY
• 064
DUCT
– E –
• 065
EAST
066
ELECTRIC
• 067
EMERGENCY
∗
068
ENTRY
• 069
EQUIPMENT
• 071
EXIT
∗
072
EXTERIOR
– F –
• 073
FACTORY
075
FAMILY
• 076
FATHERS
• 077
FENCE
• 079
FIRE
∗
• 080
FLOOR
∗
081
FLOW
082
FOIL
• 083
FOYER
084
FREEZER
• 085
FRONT
∗
– G –
• 089
GARAGE
∗
• 090
GAS
091
GATE
• 092
GLASS
093
GUEST
• 094
GUN
∗
– H –
• 095
HALL
∗
• 096
HEAT
098
HOLDUP
• 099
HOUS
E
∗
- I -
100
INFRARED
• 101
INSIDE
∗
102
INTERIOR
103
INTRUSION
– J –
104
JEWELRY
– K –
• 105
KITCHEN
∗
– L –
• 106
LAUNDRY
∗
• 107
LEFT
108
LEVEL
• 109
LIBRARY
∗
• 110
LIGHT
111
LINE
• 113
LIVING
∗
• 114
LOADING
115
LOCK
116
LOOP
117
LOW
• 118
LOWER
– M –
• 119
MACHINE
121
MAIDS
• 122
MAIN
∗
• 123
MASTER
∗
• 125
MEDICAL
∗
126
MEDICINE
128
MONEY
129
MONITOR
• 130
MOTHERS
• 131
MOTION
∗
132
MOTOR
– N –
• 134
NORTH
135
NURSERY
– O –
• 136
OFFICE
∗
• 138
OPEN
∗
139
OPENING
•
140
OUTSIDE
142
OVERHEAD
– P –
143
PAINTING
• 144
PANIC
∗
145
PASSIVE
• 146
PATIO
∗
147
PERIMETER
• 148
PHONE
150
POINT
• 151
POLICE
∗
• 152
POOL
∗
• 153
POWER
– R –
155
RADIO
• 156
REAR
157
RECREATION
159
REFRIGERATION
160
RF
• 161
RIGHT
• 162
ROOM
∗
163
ROOF
– S –
164
SAFE
165
SCREEN
166
SENSOR
• 167
SERVICE
• 168
SHED
∗
169
SHOCK
• 170
SHOP
∗
171
SHORT
• 173
SIDE
∗
174
SKYLIGHT
• 175
SLIDING
∗
• 176
SMOKE
∗
• 178
SONS
• 179
SOUTH
180
SPRINKLER
• 182
STATION
184
STORE
• 185
STORAGE
∗
186
STORY
• 190
SUPERVISED
∗
191
SUPERVISION
192
SWIMMING
193
SWITCH
– T –
194
TAMPER
• 196
TELCO
197
TELEPHONE
• 199
TEMPERATURE
200
THERMOSTAT
• 201
TOOL
202
TRANSMITTER
– U –
• 205
UP
• 206
UPPER
• 207
UPSTAIRS
∗
• 208
UTILITY
∗
– V –
209
VALVE
210
VAULT
212
VOLTAGE
– W
–
213
WALL
214
WAREHOUSE
• 216
WEST
• 217
WINDOW
∗
• 219
WING
220
WIRELESS
– X –
222
XMITTER
– Y –
• 223
YARD
∗
– Z –
• 224
ZONE (No.)
• 225
ZONE
∗
• 226
0
• 227
1
• 228
1S
T
∗
• 229
2
• 230
2ND
∗
• 231
3
• 232
3RD
∗
• 233
4
• 234
4TH
• 235
5
• 236
5TH
• 237
6
• 238
6TH
• 239
7
• 240
7TH
• 241
8
• 242
8TH
• 243
9
• 244
9TH
245
Custom Word #1
246
Custom Word #2
247
Custom Word #3
248
Custom Word #4
249
Custom Word #5
250
Custom Word #6
251
Custom Word #7
252
Custom Word #8
253
Custom Word #9
254
Custom Word #10
Note:
Bulleted (
•
) words
are
spoken by the
Tuxedo and TuxWifi Touchscreens
.
Words followed by an asterisk
(*) are spoken
by the 6160V/6150V Voice Keypads
.
Bolded
words are spoken by the 5828V keypad.
CHARACTER (ASCII) CHART (For Adding Custom Words)
32 (space)
33
!
34
"
35
#
36
$
37
%
38
&
39
'
40
(
41
)
42
*
43
+
44
,
45
–
46
.
47
/
48
0
49
1
50
2
51
3
52
4
53
5
54
6
55
7
56
8
57
9
58
:
59
;
60
<
61
=
62
>
63
?
64
@
65
A
66
B
67
C
68
D
69
E
70
F
71
G
72
H
73
I
74
J
75
K
76
L
77
M
78
N
79
O
80
P
81
Q
82
R
83
S
84
T
85
U
86
V
87
W
88
X
89
Y
90
Z
VISTA-
15P/20P/SIA Program
Guide
34
Scheduling Menu Mode
Installer Code + [#] + [6] [4]
The system provides schedules, which can be used to automatically control 11 types of system events at pre-
defined times.
Some events are reserved for the installer only.
VISTA-
20P:
Provides up to 32 schedules: 16 schedules for use by the end-
user, 16 for use by the i
nstaller.
VISTA-
15P:
Provides up to 8 schedules: 4 schedules for use by the end user, 4 for use by the installer.
NOTES:
•
The master code can only access schedules 01-
16 (VISTA-
15P = 01-
04) and events 00-
07.
•
System clock must be set before schedules c
an take effect.
•
Programmed schedules do not take effect until the next scheduled “start” time. (e.g., if programming a schedule time window
for 8AM to 5PM, the schedule does not take effect until 8AM after the schedule has been programmed.)
Schedule Mod
e
ENTER SCHED NO.
00=QUIT
00
Schedule Number
VISTA-
20P
01-
16 = end-
user schedules
17-
32 = installer
-only
VISTA-
15P
01-
04 = end-
user schedules
05-
08-
= installer
-only
[
∗
] to continue
Enter the desired schedule number.
To Quit,
enter 00.
ENTER EVENT
Enter Event
00 = clear event
01 = Relay On/Off
02 = User Access
03 = Latch Key Report to
Pager
04 = Forced Stay Arming
†
05 = Forced Away Arming
†
06 = Auto Disarm
07 = Display “Reminder”
10 = Display custom words
††
11 = Periodic Test Report
†††
Press
[
∗
] to continue.
Enter the desired event number for event you want to occur at a
specified time.
Events 10-
11 are reserved for the installer only.
Latch key report (option 03) is sent to all pagers in the user’s partition
and is active only when the sys
tem is armed (message sent is 777-
7777). User must be enabled for paging (see User Attributes in
System
Operation
section).
† Forced bypass is automatically enabled regardless of setting in field
*23.
†† If selected, system displays custom words 8, 9, and
10 at defined
time. Can be used as installer’s reminder message to the end user.
††† See key commands in Test Report Code
data field *64
section to
quickly set periodic test reporting intervals.
NOTE:
Events 07 and 10 cause the keypad to beep every 30
se conds when messages are displayed. Stop the beeps by pressing
any key.
DEVICE NUMBER
XX
Device Number
V20P:
01-
18 = device number
V15P: 01-
08, 17, 18
Press
[
∗
] to continue
.
(For event 01
-
relay on/off)
Enter the physical device number as programm
ed in
∗
79 Menu Mode,
then press [*] to continue to the “Start” prompt.
Device numbers 17 and 18 designate built
-in triggers 1 and 2
respectively.
GROUP NUMBER
X
Group Number
1-8 = group number
Press
[
∗
] to continue to the
“Start” prompt
.
(For even
t 02
-
user access)
PARTITION
X
Partition
0 = all partitions
1 = partition 1
2 = partition 2
3 = common
Press [*] to continue to the
“Start” prompt.
(V20P only; for events 03
-
07, 10)
START SMTWTFS
HH MMAM
0010000
Start Time
01-
12 = hour
00-
59 = minute
0 = AM
; 1 = PM
Days = place “1” under days
Press [
∗
] to continue.
Enter the event’s start time and days of the week to occur.
To select days, position the cursor under the desired days using
the [
∗
] key to move forward, then press “1” to select
the day.
VISTA-
15P/20P/SIA Program
Guide
35
Scheduling Menu Mode
(Continued)
STOP SMTWTFS
HH MMAM
0010000
Stop Time
01-
12 = hour
00-
59 = minute
0 = AM
; 1 = PM
Days = place “1” under days
Press [
∗
] to continue.
(For events 01
-
relay on/off; 02
-
user access; 03
-
latch key report)
Ent
er the event’s stop time and days of the week to occur.
To select days, position the cursor under the desired days using
the [
∗
] key to move forward, then press “1” to select the day.
REPEAT OPTION
0 - 4
X
Repeat Option
0 = do not repeat
1 = repeat w
eekly
2 = repeat biweekly (every
other week)
3 = repeat every third week
4 = repeat every fourth
week
Press [
∗
] to continue.
Enter the desired repeat option for this schedule.
e.g., To make a schedule that happens everyday you would
select all days with a
repeat count of 1. To make a schedule
that runs for one week then stops, select everyday with a repeat
count of 0.
RANDOMIZE
0=NO 1=YES X
Randomize
0 = no
1 = yes
Press [
∗
] to continue
and
return to ENTER SCHED
NO. prompt to program the
next s
chedule.
(For events 01 and 11)
If selected, the scheduled start and stop times will vary within 60
minutes of the “hour” time. For example, if a schedule is set to
start at 6:15pm, it will do so the first time 6:15pm arrives, but on
subsequent days it wi
ll start anytime between 6:00 and 6:59
p.m.
NOTE:
Do not use the random option if the start and stop times
are within the same “hour” setting, otherwise unpredictable
results may occur (e.g., the randomized stop time may occur
before the start time).
Setting the Time Clock
IMPORTANT:
The Real
-Time Clock must be set before the end of the installation.
NOTE:
All partitions must be disarmed before the date/time can be set.
1. Master Code +
[#]
+ [6] [3]
2. Press [
∗
] w
hen the time/date is displayed.
A cursor appears under the first digit of the hour.
The cursor will advance
automatically, but if you need to move the cursor manually, you can.
To move cursor ahead, press [
∗
]. To go back, press [#].
•
Enter the 2-
digit hour setting.
•
Enter the 2-
digit minute setting.
•
Press [1] for PM or [2] for AM.
•
Enter the last two digits of the current year.
•
Enter the 2-
digit month setting.
•
Enter the 2-
digit day setting.
3. To exit, press [
∗
] when cursor is at the last digit
. If you wait, it will timeout and exit the clock without saving changes.
VISTA-
15P/20P/SIA Program
Guide
36
∗
29
Communicator Menu Mode
This mode is for programming an IP
, Cell, or IP/
Cell
Communicat
or Module using an alpha keypad. Alternatively, these
options can be programmed via the AlarmNet Direct website. After programming is complete, the module must be registered
with AlarmNet
before
reporting
via the communicat
ion device
can occur
. Refer to the
device’s instructions for registration
procedures.
NOTE:
The module must be set to device address 3.
IMPORTANT:
The use of
an
Alarm
Net Communicator
requires an AlarmNet
–I account. Please obtain the
account information from the central st
ation prior to
programming this module.
Using an Alpha Keypad as a 7720P Programming
Tool
When programming with
∗
29 menu mode, the alpha
keypad mimics the functions of the 7720P
Programming Tool. See figure
to right
and table
below
for 7720P key functions. Each key has two
possible functions: a normal function and a SHIFT
function.
Normal functions:
The numeric values labeled
directly on the keys and the left
-hand functions
shown in diagram on the ABC keys. To perform a
normal key function, simply press the desired key.
SHIFT functions:
Those functions shown in diagram
above the numerical keys and the right
-hand
functions shown on the ABC keys. To perform a
SHIFT key function, press SHIFT key (D key), then
press the desired function key (shift funct
ion is
indicated by the lit READY LED).
7720P Emulation Template for Alpha Keypads
∗
29 IP/GSM Program Mode
Press
∗
29 while in Data Field Programming mode. The following prompts appear.
ENABLE IP/GSM?
0=No, 1=Yes
Enable IP/GSM?
0 = no, not using
AlarmN
et
Communicator
;
1 = yes using IP and/or
Cell
module
[
∗
] to continue
[Default = 0 (no Alarm
Net
communicator
)]
If using a communication device, enter 1 at this prompt and
enter 1-
Prog at the next prompt to program
the dev
ice
. Use the
communication device’s Installation Guide for details of the
device’s programming prompts and instructions for registration.
Fixed
-Word Keypad Note:
Although programming
these
options cannot be done via a fixed-
word keypad,
they
can be
enabled by doing the following:
Enter
∗
29
(to enter
menu mode), then press
1 + [
∗
] + [
∗
]
1=PROG 2=DIAG
0=QUIT
Programming /
Diagnostics Select
1= Prog (program the
IP/Cell
options)
2 = Diag (
diagnostic mode)
0 = Quit; returns
to data
field programming
mode
Select whether you want to program the communication device
or enter the device’s diagnostic mode.
Diagnostic Mode Note:
Diagnostic mode option available only
for
communicators with firmware version 2.4.16 or higher.
VISTA-
15P/20P/SIA Program
Guide
37
*29 Co
mmunicator Menu Mode
(Continued)
Normal and SHIFT key Functions While in
∗
29 Menu Mode
Key
Normal Key Function
SHIFT Key Function
(A) = BS/ESC
[BS]: Press to delete entry
[ESC]: Press to quit Program Mode
Also, can reset
EEPROM
defaults
†
(B) =
↓
/
↑
[
↓
]: Scroll down programming
[
↑
]: Scroll up programming
(C) = N/Y
[N]: Press for "NO" answer
[Y]: Press SHIFT
-
Y for "YES" answer
(D) = SHIFT
Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a key is pressed.
Press ag
ain for each SHIFT function desired.
1/A
[1]: For entering the number 1
[A]: Used for entering C.S. ID number
2/B
[2]: For entering the number 2
[B]: Used for entering C.S. ID number
3/C
[3]: For entering the number 3
[C]: Used for entering C.S. ID numb
er
4/D
[4]: For entering the number 4
[D]: Used for entering C.S. ID number
5/E
[5]: For entering the number 5
[E]: Used for entering C.S. ID number
6/F
[6]: For entering the number 6
[F]: Used for entering C.S. ID number
7/S
[7]: For entering the numb
er 7
[S]: Press to display diagnostic status
8/T
[8]: For entering the number 8
[T]: Press to send TEST messages
9/X
[9]: For entering the number 9
[X]: Press to reset the
Alarm
N
et
c
ommunic
a
tor
[
∗
] / SPACE
[
∗
]: Used to select programming
options
[SPACE]: Not used
0
[0]: For entering the number 0
[#] / ENTER
[#] / ENTER: Press to accept entries
No SHIFT function
†
Active only when the "REVIEW?" prompt is displayed
Registering the Communication Device with AlarmNet
The communication devic
e must be registered with AlarmNet before internet communication (via IP or
Cell) can occur.
Register Using the Alpha Keypad and
∗
29 Menu Mode
1. Enter *29 Menu mode, select Diagnostic mode, then press Shift then [
↑
] key (D key followed by the B key).
The registration
message is sent (“Registering” displayed) and the control waits for the acknowledgment.
2. “Registration SUCCESS” displayed, indicating successful registration.
Or Register with AlarmNet Direct Website or by Phone
To regi
ster via AlarmNet Direct Website, please go to:
https://services.alarmnet.com/AlarmNet360/AlarmNetDirectV
.
To regi
ster by phone,
call 1
-800-
222-
6525. You will need the MAC
ID and MAC CRC
number and Subscriber information.
Communication Device Status
Report Codes
The Communication Device sends status messages to the control panel for network connectivity failures. Trouble messages are
displayed on the keypad as “Check 103,” with status displayed as “LngRng Radio” followed by a 4-
digit keypad display s
tatus
code, defined below.
Keypad Display Status Codes
CODE
DESCRIPTION
0000
Control panel lost communication with internal device
0005
Communication
device has lost contact with AlarmNet
-
G
network
000F
Communication
device
is not registered; account
not activated
0019
Cell
module shut down
0400
Communication
device Power
-
on reset
VISTA-
15P/20P/SIA Program
Guide
38
Uploading/Downloading via the Internet
UL
: Up/downloading via the Internet has not been evaluated by UL.
This control, when
used with a compatible Internet/Intranet Communication Device, supports upload/download programming
capability via the Internet using the AlarmNet network or, depending on the communication module used, a Private local area
network (Intranet). This allows
site maintenance independent of central station monitoring, and modification to sites globally via
the Internet. Depending on the module used, Internet connection from the protected premises is either via high speed
(broadband) cable or phone service, or v
ia the
digital cellular network
.
Refer to the instructions provided with the communication module for information regarding its installation, programming, and
registration. The System Requirements table below lists two sets of system requirements, depending upon whether you intend to
communicate over the Internet or whether you are communicating over a Private LAN (Intranet).
Compatible Communication Modules:
The following modules support Internet uploading/downloading, but future m
odules may
also provide Internet upload/download support; refer to the module’s instructions for compatibility
.
System Requirements
Internet Communication
At the Installation Site:
•
Appropriate Internet Communication Module
•
7720P Programmer
•
Broadband Internet Access (for wired modules)
•
Broadband (Cable/DSL) Modem (for wired modules)
•
Broadband (Cable/DSL) Router (for wired modules if
connecting more than one device to the Inter
net)
•
IP compatible Control Panel
At the Downloading Office:
•
Broadband Internet Access
•
Broadband (Cable/DSL) Modem
•
Broadband (Cable/DSL) Router (optional, if connecting
more than one device to the Internet)
•
Computer running Compass Downloading S
oftware
version that supports Internet upload/download for this
control.
Intranet (Private LAN) Communication
, if applicable*
At the Installation Site:
•
Internet/Intranet Communication Module
•
7720P Programmer
•
Ethernet Network Connection
•
IP compatible Control Panel
At the Downloading Office:
•
7810
Receiver
and
Internal Router
•
Computer(s) running the following software:
- Compass Downloading Software version that supports
IP upload/download for this control.
- Compass Connect Data Server
Application
- Compass Connect Control Server Application
*
see module’s instructions for applicability for LAN usage
NOTE:
Compass, the Compass Connect Data Server, and the
Compass Connect Control Server applications may all be installed
on the same computer if desired. If they are installed on one
computer, the computer must have a fixed IP Address.
To set up the control panel, do the following:
1. Connect the communication device to the control panel’s ECP (keypad) terminals.
2. Internet Users: Connect the communication device to the Internet via a cable/DSL modem and router.
Intranet Users: Connect the communication device to the Intranet (LAN) via the appropriate Ethernet connection.
3. Enable the communication device (using
∗
29 Menu mode) to enable alarm reporting and module supervision.
4. Using the communication device’s programming menus (via
∗
29 Menu mode or 7720P programmer), program the
communication device for address 3 and program the device’s other options as required.
5. Register the com
munication device
with AlarmNet. The communication device
must be registered before downloading or
alarm reporting can take place.
To perform upload/download functions:
1. Connect the computer to the Internet and start the Compass downloading software.
2. Open the control’s account, then select the Communications function and click the Connect button.
3. At the Connect screen, check that the control’s MAC address is entered and the TCP/IP checkbox is checked.
4. Click Connect. The Internet connection to
the control is made automatically via AlarmNet.
5. Once connected, use the Compass downloading software as normal to perform upload/download functions.
VISTA-
15P/20P/SIA Program
Guide
39
Zone Type Definitions
Zone types define the way in which the system responds to
faults in each zone.
Type 00 Zone Not Used
Program a zone with this zone type if the zone is not used.
Type 01 Entry/Exit Burglary #1
•
Assign to zones that are used for primary entry and exit.
•
Provides entry delay when zone is faulted if control is
armed
in the Away, Stay, or Night
-Stay modes.
•
No entry delay provided when the panel is armed in the
Instant/Maximum mode.
•
Entry delay #1 is programmable for each partition (field *35).
•
Exit delay begins whenever the control is armed, regardless of
the arming mode selected, and is programmable (field
Q
34).
Type 02 Entry/Exit Burglary #2
•
Assign to zones that are used for entry and exit and require
more time than the primary entry/exit point.
•
Provides a secondary entry delay,
similar to
entry
delay #1.
•
Entry delay #2 is programmable for each partition (field *36).
•
Exit delay is same as described for Type 01.
Type 03 Perimeter Burglary
•
Assign to all sensors or contacts on exterior doors and
windows.
•
Provides an instant alarm if the zone is faulted when the panel is
armed in the Away, Stay, Night
-Stay, Instant or Maximum
modes.
Type 04 Interior Follower
•
Assign to a zone covering an area such as a foyer, lobby, or
hallway through which one must pass upon entry (to and from
the keypad)
.
•
Provides a delayed alarm (using the programmed entry 1
time) if the entry/exit zone is faulted first. Otherwise this zone
type gives an instant alarm.
•
Active when the panel is armed in the Away mode.
•
Bypassed automatically when the panel is armed
in the Stay
or Instant modes;
if armed in Night
-Stay mode, zones
assigned to zone list 05 (night
-stay zone list) are not
bypassed when system armed in Night
-Stay mode.
Type 05 Trouble by Day/Alarm by Night
•
Assign to a zone that contains a foil
-protected door or window
(such as in a store), or to a zone covering a sensitive area
such as a stock room, drug supply room, etc.
•
Can also be used on a sensor or contact in an area where
immediate notification of an entry is desired.
•
Provides an instant alar
m if faulted when armed in the Away,
Stay, Night
-Stay, Instant or Maximum (night) modes.
•
During the disarmed state (day), the system will provide a
latched trouble sounding from the keypad (and a central
station report, if desired).
Type 06 24-
hr Silen
t Alarm
•
Usually assigned to a zone containing an emergency button.
•
Sends a report to the central station but provides no keypad
display or sounding.
Type 07 24-
hour Audible Alarm
•
Assign to a zone that has an emergency button.
•
Sends a report to the central station, and provides an alarm
sound at the keypad, and an audible external alarm.
Type 08 24-
hour Auxiliary Alarm
•
Assign to a zone containing an emergency button, or to a
zone containing monitoring devices such as water or
temperature sensor
s.
•
Sends a report to the central station and provides an alarm
sound at the keypad. (No bell output.)
Type 09 Supervised Fire
•
Provides a fire alarm on short circuit and a trouble condition
on open circuit. A fire alarm produces a pulsing bell output.
•
This zone type is always active and cannot be bypassed.
Type 10 Interior w/Delay
•
Provides entry delay (using the programmed entry time), if
tripped when the panel is armed in the Away mode.
•
Entry Delay 1 begins whenever sensors in this zone are
violated, regardless of whether
an entry/exit delay zone was
tripped first.
•
Bypassed when the panel is armed in the Stay or Instant modes; if
armed in Night
-Stay mode, zones assigned to zone list 05 (night
-
stay zone list) are not bypassed w
hen system armed in Night
-Stay
mode.
Type 12 Monitor Zone
•
Works as a dynamic monitor of a zone fault/trouble (not alarm). In
the case of a short/open, the message, "*ALARM*
-24 Hr. Non-
Burg.
-#XXX " (where XXX is the zone number) will be sent to the
Cen
tral Station. The system keypad will display a “check” message
indicating the appropriate zone (but keypad beeping does not
occur). Upon restoral of the zone, the message, "*RESTORE*
-24
Hr. Non
-Burg.
-#XXX
" will be sent to the Central Station.
•
The “check” message will automatically disappear from the keypad
dynamically, when the zone restores; a user code + off sequence is
not needed to reset the zone.
•
Faults of this zone type are independent of the system, and can
exist at the time of arming without
interference.
•
Since this is a “trouble” zone type, do not use this zone type with
relays set to activate upon “alarm.”
Type 14 24 Hour Carbon Monoxide Monitor
•
Assigned to any zone with a carbon monoxide detector.
•
A carbon monoxide alarm produces
keypad and detector sounding
(does not affect bell output
).
•
Always active and cannot be bypassed.
Type 16 Fire w/Verification
•
Provides a fire alarm when zone is shorted, but only after
the
alarm
is verified
to help eliminate
false alarms due to elect
rical or
physical transients
.
•
Verifies alarm by resetting smoke detectors after short is detected
(removes power 7 seconds for zone 1, 3 seconds for trigger
output). Another short circuit within 90 seconds triggers fire alarm
,
otherwise first alarm is i
gnored.
•
Provides a trouble response when zone is open.
Type 20 Arm
-Stay (BR only)
•
Arms the system in Stay mode when the zone is activated.
•
Pushbutton units send the user number to the central station when
arming or disarming.
•
User number for butt
on must be assigned.
Type 21 Arm
-Away (BR only)
•
Arms the system in Away mode when the zone is activated.
•
Pushbutton units send the user number to the central station when
arming or disarming.
•
User number for button must be assigned.
Type 22 Disarm (BR only)
•
Disarms the system when the zone is activated.
•
User number for button must be assigned.
Type 23
*
No Alarm Response
•
Can be used on a zone when an output relay action is desired, but
with no accompanying alarm (e.g., lobby door access).
Type 24 Silent Burglary
•
Usually assigned to all sensors or contacts on exterior doors and
windows where bells and/or sirens are NOT desired.
•
Provides an instant alarm, with NO audible indication at any
keypad or external sounder, if the zone is faulted
when the system
is armed in the Away, Stay, Instant, or Maximum modes.
•
A report is sent to the central station.
Type 77 Keyswitch
•
Assign to zone wired to a keyswitch.
•
Do not use input type “BR” devices with this zone type.
Types 90-
93 Configurable
Allows for various custom responses. Options include response to
ent
ry/exit delays, response opens/shorts, types of alarm/trouble
sounding, dial delay, and unique Contact ID report codes. Types 92
and 93 can only be programmed via downloader. UL installations:
Zone Types 90 -
93 may not be used as fire or burglar alarm zones
on fire or UL burglar alarm installations.
*
The system can still be armed when these zone types are in a
faulted condition.
VISTA-
15P/20P/SIA Program
Guide
40
Report Code Formats
The following table describes the communication formats.
FORMAT TYPE
DESCRIPTION
3+1 an
d 4+1
Standard Formats
Ex.
SSS(S) A
Comprises a 3
-
(or 4
-
) digit subscriber number and a single
-
digit report code (e.g.,
Alarm, Trouble, Restore, Open, Close,
etc.
).
Ex.
S = Subscriber ID; A = Report Code
3+1 and 4+1
Expanded Formats
Ex.
SSS(S) A
AA
A(A) Z
Comprises a 3
-
(or 4
-
) digit subscriber number and a two
-
digit report code. The first digit
is displayed on the first line.
The first digit is repeated on the second line 3 (or 4) times
followed by the second, “expanded”
digit.
Ex.
S = Subscriber
ID; A = Report Code
–
1st digit;
Z = Typically Zone Number
–
2nd digit
4+2 Format
E
x.
SSSS AZ
Comprises a 4
-
digit subscriber number and 2
-
digit report code.
Ex.
S = Subscriber ID; A = Report Code; Z = Typically Zone Number)
ADEMCO Contact ID
Reporting Format
Ex.
CCCC Q EEE GG ZZZ
Comprises a 4
-
or 10
-
digit subscriber number (depending on format selected), 1
-
digit
event qualifier (“new” or “restore”), 3-
digit event code, and 3-
digit zone number, user
number, or system status number (
see below for example expl
anation
).
ADEMCO
Contact ID®
The
ADEMCO
Contact ID
®
Reporting Format comprises the following:
4-digit or 10-
digit subscriber number (depending on format selected).
1-digit event qualifier (“new” or “restore”).
3-digit event code.
2-digit Partition No.
3-digit zone number, user number, or system status number (see table below
).
ADEMCO
Contact ID
®
Reporting takes the following format: CCCC(CCCCCC) Q EEE GG ZZZ
where:
CCCC(CCCCCC) =
Customer (subscriber) ID
Q =
Event qualifier, where: E = new event
, and R = restore
EEE =
Event code (3 hexadecimal digits)
GG =
Partition Number (system messages show “00”)
ZZZ =
Zone/contact ID number reporting the alarm, or user number for open/close reports. System
status messages contain zeroes in the ZZZ location.
TABLE OF CONTACT ID EVENT CODES
(Some
event codes may not apply to certain control panels
;
for a complete list of event codes, refer to the central office receiver manual
)
Code
Definition
110
Fire Alarm
121
Duress
122
Alarm, 24
-
hour Silent
123
Alarm
, 24
-
hour Audible
131
Alarm, Perimeter
132
Alarm, Interior
134
Alarm, Entry/Exit
135
Alarm, Day/Night
; Wireless Tamper Alarm while
Armed
143
Alarm, Expansion Module
145
ECP Module cover tamper
146
Silent Burglary
150
Alarm, 24
-
Hour Auxiliary/Monit
or zone
162
Carbon Monoxide
301
AC Power
302
Low System Battery/Battery Test Fail
305
System Reset (Log only)
321
Bell/Siren Trouble
333
Trouble, Expansion Mod. Supervision
341
Trouble, ECP Cover Tamper
344
RF Receiver Jam
351
Telco Line Fault
35
3
Long Range Radio Trouble
354
Failure to Communicate (log only)
373
Fire Loop Trouble
374
Exit Error Alarm
380
Global Trouble, Trouble Day/Night
381
RF Sensor Supervision
382
Supervision Auxiliary Wire Zone
Code
Definition
383
RF Sensor Tamper
384
RF Sensor Low
-
battery
393
Clean Me
401
R401
–
Armed AWAY / MAXIMUM
E401
-
Disarmed
403
Schedule Arm/Disarm AWAY
406
Cancel by User
407
Remote Arm/Disarm (Downloading)
408
Quick Arm AWAY
409
Keyswitch Arm/Disarm
AWAY
441
R441
–
Armed STAY / INSTANT
E441
– Disarmed
Quick
-
Arm STAY/INSTANT
442
Keyswitch Arm/Disarm STAY
455
Scheduled Arm Fail
459
Recent Closing (SIA panels only)
570
Bypass
601
Manually Triggered Dialer Test
602
Per
iodic Test
606
Listen
to Follow
607
Walk Test Entered/Exited
623
Event Log 80% Full
625
Real
-
Time Clock was Changed (log only)
627
Program Mode Entry (log only)
628
Program Mode Exit (log only)
642
Latch Key (log only)
750
-
789
Reserved for C
onfigurable Zone Type report
codes (check with central station when using
these codes)
VISTA-
15P/20P/SIA Program
Guide
41
System Security Codes
The system
provides one Installer code, one System Master code, plus a set of other user codes intended for other users of
the system. These codes can each be assigned one of 5 authority levels, which determine the functions each code can
perform as listed in the table below.
VISTA-
20P:
Provides 48 security codes (plus Installer code), including one System Master code, two Partition Master
codes, and 45 general user codes.
VISTA-
15P: Provides 32 security codes (plus Installer code), including one System Master code and 31 general user codes.
Authority Levels
(can be assigned to users 03-
49 only; users 1 and 2 cannot be changed)
Level
User No.
Functions
Installer
01
(default=4112) perform all security functions except can disarm only if used to arm; can
enter program mode; can change System Master code; cannot assign any other user codes
NOTE: For security purposes, the factor
y default installer code should be changed.
System Master
02
(default 1234) only one system master code per system; can perform all security functions,
add/delete users in either partition, change system master code, view event log, set system
clock, pro
gram keypad macro, program scheduled events, activate output devices
(triggers/relays)
Partition Master
(default)
P1 = 03
P2 = 33
VISTA
-
20P. Same as Master, except add/delete users limited to assigned partition only,
(these users can be assigned different
authority levels, if desired; any user can be
assigned the partition master authority level)
0
-
User
03
-
49 (V20P)
03-
33 (V15P)
perform security functions (arm, disarm, etc.) only; cannot add/delete users, view event log
set system clock or program scheduled events
1
-
Arm Only
see “user”
arm system only
2
-
Guest
see “user”
can disarm the system only if it was used to arm the system
3
-
Duress
see “user”
performs security functions, but also silently sends a duress message to the central station;
reports as
duress code user number.
4
-
Partition Master
see “user”
VISTA
-
20P. See Partition Master paragraph above; used to assign other user numbers as
partition masters
Refer to the user guide for detailed procedures on adding/deleting security codes and changing
user attributes.
The following is a brief description of how to add user codes.
Changing the System Master code:
Using Installer code: Installer code + [8] + 02 + new code
Using current System Master code: System Master code + [8] + 02 + new code + new
code again
Adding a User Code:
Master code + [8] + 2-
digit user no. + user’s code
Deleting a User Code:
Master code + [8] + 2-
digit user no. + [#] [0]
Assigning Attributes:
Master code + [8] + 2-
digit user no. + [#] [attribute no.] + value
Attributes:
Val
ues
1 =
Authority Level
0-4 (see Authority Level table above)
2 =
Access Group
0-8 (0 = not assigned to a group)
3 =
Active Partition(s)
1, 2, 3 (common)
for this user;
Enter partitions consecutively if more than one and press [#] to end the entries.
4 =
RF Zone No.
Assigns user number to button type zone for arm/disarm (
keyfob must be
enrolled in system first
; see
Wireless Key Templates
section).
Deactivating a key fob:
You can deactivate the arming/disarming functions for
a key fob (ex. if l
ost or stolen) by deleting the associated key fob user. See
“Delete a User” above. Other key fob functions such as panic or device
activation (if programmed) remain active. To fully remove the programming for
a key fob, delete the zone(s) associated with t
he key
fob functions.
IMPORTANT SECURITY NOTICE
Please inform the User about the security importance of their key fob, and what to
do if it is lost.
Explain that the key fob is similar to their keys or access card. If lost or stolen,
another person can compromise their security system. They should immediately
notify the Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then
remove the key fob programming from the security system.
5 =
Open/Close Paging
1 for yes, 0 for no
VISTA-
15P/20P/SIA Program
Guide
42
Keypad Functions
The following is a brief list of system commands. For detailed information concerning system functions, refer to the User's
Manual. For Touch Screen style keypad users, refer to the separate Touch Screen keypad (AUI) User’s Guide.
Keypad Commands
Function
Description
Silence Burglary Alarms
Pressing any key will silence the keypad sounder for 10 seconds. Disarming the system
(security code + OFF) silences both keypad and external sounders.
Silence Fire or Carbon
Monoxide Alarms
Press the OFF [1] key to silence the keypad sounder and, for fire alarms, the external
sounder.
Quick Arm
If enabled (field
∗
21), you can press [#] in place of the system's security code, plus the desired
arming key (Away, Stay, Instant, Maximum)
Singl
e
-
Button arming
If programmed (*57 Function Key menu mode), lettered keys A
-
D can be used for arming,
using options 3
-
AWAY, 4
-
STAY, 5
-
NIGHT
-
STAY, or 6
-
Step
-
Arming
Alarm Memory
When the system is disarmed, any zones that were in an alarm condition during t
he armed
period will be displayed. To clear this display, simply repeat the disarm sequence (enter the
security code and press the OFF key) again.
Arming Away
Enter code + AWAY [2] or simply press appropriate lettered key on the keypads
.
If the “Auto
-
Stay
Arm” feature is enabled (field *84) and the entry/exit door
is not
opened and closed
within the programmed exit delay time, the system will automatically arm in STAY mode if
armed from a wired keypad (non-
RF device). If the door
is
opened and closed withi
n the exit
delay period, the system arms in AWAY mode.
Arming Stay
Enter code + STAY [3] or simply press appropriate key on the keypads (see “Single
-
Button
Arming” above). See “Arming Away” above for Auto
-
Stay arming feature.
Arming Night
-
Stay
Enter code
+ STAY [3] + STAY [3] or simply press appropriate key on the keypads (see
“Single
-
Button Arming” above).
Arming Instant
Enter code + INSTANT [7].
Arming Maximum
Enter code + MAXIMUM [4] or simply press appropriate lettered key on the keypads (see
“Singl
e
-
Button Arming” above).
Disarming
Enter code
+ OFF [1]. If entry delay or an alarm is active, you do not need to press OFF.
Bypassing Zones
Enter code + BYPASS [6] + zone number(s).
Forced (Quick) Bypass
To automatically bypass all faulted zones, use t
he “Quick Bypass” method. Enter code +
BYPASS + [#], then wait for all open zones to be displayed. Arm when display indicates
“ZONE BYPASSED” and “READY TO ARM”.
Chime Mode
Enter code + CHIME [9]. To turn chime off, enter code + CHIME again.
Activate Out
put
Devices
[Security Code] + # + 7 + [2
-
digit Device #] activates (starts) that device.
[Security Code] + # + 8 + [2
-
digit Device #] deactivates (stops) that device.
VISTA-
15P/20P/SIA Program
Guide
43
Worksheet
for
∗
56 Z
one Programming
(VISTA-
15P supports up to 32 zones: 1-
6, 9-
34, 49-
56) [default shown in brackets]
Zone
Zn Type
Part.
Report
Hardwire
Type
Rsp. Time
Location
1
[09]
[1]
[EOL]
[1]
2
[01]
[1]
[EOL]
[1]
3
[03]
[1]
[EOL]
[1]
4
[03]
[1]
[EOL]
[1]
5
[03]
[1]
[EOL]
[1]
6
[03]
[1]
[EOL]
[1]
7
[03]
[1]
[EOL]
[1]
8
[03]
[1]
[EOL]
[1]
Zone
Zn Type
Part.
Report
Input Type
Loop
Serial No.
Location
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
NOTES:
Zone Type: see chart
∗
56
Zone Programming Menu
mode section.
Report Code: enabled if
first digit is a non-
zero
number.
Hardwire Type (zns 2-
8):
0 = EOL
3 = ZD
1 = NC
4 = DB
2 = NO
Input Type:
2 = AW (zones 9-
48)
3 = RF (zones 9-
48)
4 = UR (zones 9-
48)
5 = BR (zones 49-
64)
NOTE:
Zones 9-
16 not
available if zone
doubling enabled.
Response Time:
0 = 10msec
1 = 350msec
2 = 700msec
3 = 1.2 sec
Reserved Zones
91 =
addressable device
report
enable/disable
default zone type =
[05].
92 =
Duress report
bl /di bl
VISTA-
15P/20P/SIA Program
Guide
44
Worksheet for
∗
56 Zone Programming
(Continued)
Zone
Zn Type
Part.
Report
Input Type
Loop
Serial No.
Location
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
[1]
[BR]
50
[1]
[BR]
51
[1]
[BR]
52
[1]
[BR]
53
[1]
[BR]
54
[1]
[BR]
55
[1]
[BR
]
56
[1]
[BR]
57
[1]
[BR]
58
[1]
[BR]
59
[1]
[BR]
60
[1]
[BR]
61
[1]
[BR]
62
[1]
[BR]
63
[1]
[BR]
64
[1]
[BR]
95
[00]
N/A
**
N/A
N/A
N/A
keypad [1] / [
∗
]
96
[00]
N/A
**
N/A
N/A
N/A
keypad [3] / [#]
99
[06]
†
N/A
**
N/A
N/A
N/A
keypad [
∗
] / [#]
** Emergency key zones 95, 96, and 99 report the partition of the keypad used to activate the emergency zones.
† “06 = non-
SIA controls; “00” = SIA controls
VISTA-
15P/20P/SIA Program
Guide
45
Worksheet
for
∗
57
Function Key Programming
Optio
n
Function
A
P1
P2
com
B
P1
P2
com
C
P1
P2
com
D
P1
P2
com
Comments
01
Paging
02
Time Display
03
Arm AWAY
04
Arm STAY
05
Arm NIGHT
-STAY
06
Step Arming
07
Device Activation
Device:
08
Comm. Test
09
Macro Key 1
Assign each macro key to only a single partition.
†
10
Macro Key 2
Assign each macro key to only a single partition.
†
11
Macro Key 3
Assign each macro key to only a single partition.
†
12
Macro Key 4
Assign each macro key to only a single partition.
†
00
Emergency Keys:
zone 95
zone 99
zone 96
paging
Personal Emergency
n/a
Silent Alarm
n/a
Audible Alarm
n/a
Fire
n/a
Emergency Keys:
A = paired keys [1] / [
∗
] (zone 95); B = paired keys [
∗
] / [#] (zone 99); C = paired keys [3] / [#]
(zone 96)
† There are only four macros system
-
wide.
VISTA-
15P/20P/SIA Program
Guide
46
Worksheet
for
∗
79
Output Relay
/X-10
Programming
Applicable only if Relays and/or Powerline Carrier
(X-10)
Devices are to be used.
∗
79 RELAY/POWERLINE CARRIER (X
-10) DEVICE MAPPING (Must program before using *80)
OUTPUT TYPE
OUTPUT TYPE
(09
-
16 apply to VISTA
-
20P only)
Relay
X10
Relay
X10
Output
No.
Module
Addr.
Pos
(1
-
4)
Unit
No.
Description
Outpu
tNo.
Module
Addr.
Pos
(1
-
4)
Unit
No.
Description
01
09
02
10
03
11
04
12
05
13
06
14
07
15
08
16
17
On
-Board Trigger 1
norm output =
18
On
-Board Trigger 2
norm output =
Worksheet
for
∗
81
Zone List Programming
Fill in the required data on the worksheet below and follow the procedure in the installation manual as you enter the
data during the displays and prompts that appear in sequence.
NOTE:
Record desired zone numbers below, noting that a list may include
any
or
all
of system's zone numbers.
List No.
Used For...
Contains These Zones...
01
General Purpose (GP)
02
General Purpose
03
Chime
-by-Zone or GP
(see field *26 for Chime-
by-Zone option)
04
Cross Zones or GP
(see field *85 for Cross Zone Timer option)
05
Night
-Stay Zones or GP
06
Dial Delay Disable or GP
V20PSIA/V15PSIA:
see field *50 for Dial Delay Disable option
07
Unlimited Reports or GP
V20PSIA/V15PSIA:
see field *93 for Unlimited Reports option
08
General Purpose
09
Zones activating pager 1
10
Zones activating pager 2
11
Zones activating pager 3
(VISTA-
20P)
12
Zones activating pager 4
(VISTA-
20P)
VISTA-
15P/20P/SIA Program
Guide
47
Worksheet
for
∗
80
Output Function Programming
Fill in th
e required data on the worksheet below and follow the programming procedure in the installation manual as you
enter the data during the displays and prompts that appear in sequence.
Notes:
1.
For Relays, 4229 and 4204 devices are programmed in *79, *80,
and *81 modes.
2.
For
X- 10
devices
, field
Q
27 must be programmed with a House Code.
3
. Tampers of expansion units cannot be used to operate devices.
Output
Function
Number
(V20P=1-
48)
(V15P=1-
24)
Activation Type and Detail
Partition
Number
(P)
(if using ZT trig)
0 = any
1 = partition 1
2 = partition 2
3 = common
Event (for zone list/activated by)
Action
0 = off
1 = close 2 secs
2 = stay closed
3 = pulse
4 = toggle
5 = duration 1
††
6 = duration 2
††
Output
Number
V20P=1
-18
V15P=1
-
8,
17, 18
Device
Type
R = relay
T = tr
igger
X = X10
Activated by
0=delete
1=zn list
2=zn type
3=zn no.
Zone List
(ZL)
1
-8 = list
Zone Type
(ZT)
(see table
below)
Zone No.
(ZN)
00=none
V20P: 01-
64
V15P: 01-
06,
09-
34, 49-
56
By Zone List
0 = restore
1 = alarm
2 = fault
3 = trouble
By Zone No.
0 = restore
1 = alrm/flt/trbl
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VISTA-
15P/20P/SIA Program
Guide
48
Worksheet for *80 Output Function Programming
(Continued)
Output
Function
Numb
er
(V20P=1-
48)
(V15P=1-
24)
Activation Type and Detail
Partition
Number
(P)
(if using ZT trig)
0 = any
1 = partition 1
2 = partition 2
3 = common
Event (for zone list/activated by)
Action
0 = off
1 = close 2 secs
2 = stay closed
3 = pulse
4 = toggl
e
5 = duration 1
††
6 = duration 2
††
Output
Number
V20P=1
-18
V15P=1
-
8,
17, 18
Device
Type
R = relay
T = trigger
X = X10
Activated by
0=delete
1=zn list
2=zn type
3=zn no.
Zone List
(ZL)
1-8 = list
Zone Type
(ZT)
(see table
below
Z
one No.
(ZN)
00=none
V20P: 01
-64
V15P: 01
-06,
09
-34, 49-
56
By Zone List
0 = restore
1 = alarm
2 = fault
3 = trouble
By Zone No.
0 = restore
1 = alrm/flt
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
ZONE T
YPE/SYSTEM OPERATION –
Choices for Zone Types are:
00 = Not Used
05 = Trouble Day/Alarm Night
10 = Interior w/Delay
24 = Silent Burglary
01 = Entry/Exit#1
06 = 24 Hr Silent
12 = Monitor Zone
77 = Keyswitch
02 = Entry/Exit#2
07 = 24 Hr Audible
14 = Car
bon Monoxide§§
90-
91 = Configurable
03 = Perimeter
08 = 24 Hr Aux
16 = Fire w/Verification
04 = Interior Follower
09 = Fire
23 = No Alarm Response
§§ when used with an output function,
the carbon monoxide zone type
activates
only upon CO alarms. Does
not
activate
for trouble conditions.
Choices for System Operation are:
20 = Arming–
Stay
38 = Chime
54 = Fire Zone Reset
21 = Arming–
Away
39 = Any Fire Alarm
58 = Duress
22 = Disarming (Code + OFF)
40 = Bypassing
66 = Function key†
31 = End of Exit Time
41 = **AC Power Failure
67 = Bell Failure
32 = Start of Entry Time
42 = **System Battery Low
68 = TELCO Line Fault
33 = Any Burglary Alarm
43 = Communication Failure
78 = Keyswitch red LED†††
36 = **At Bell Timeout***
52 = Kissoff
79 = Keyswitch green LED†††
Note:
In normal operation mode:
Code + # + 7 + NN Key Entry
starts
Device
Code + # + 8 + NN Key Entry
stops
Device
** Use 0 (any) for Partition No. (P) entry.
*** Or at Disarmin
g, whichever occurs earlier.
† Use *57 Menu mode to assign the function key.
†† Duration is set in program field *177.
††† Device action not used for these choices.
VISTA-
15P/20P/SIA Program
Guide
49
Worksheet
for
Schedules
Installer code + [#] + [6] [4]
. The
master code can only access schedules 01-
16 for VISTA
-20P, 01-
04 for VISTA
-15P, and
events 00-
07 for both controls; VISTA
-15P supports up
to 8 schedules, VISTA
-20P supports up to 32 schedules
.
No.
Event
Device No.
Group No.
Partition
Start Time/
Stop Time/
Repeat
Random
(see list below)
for “01” events:
for “02” events:
for “04
-06” events:
Days
Days
(1-4)
(yes/no)
enter 01-
18
enter 1-
8
enter 1, 2, or 3
(VISTA-
20P)
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Events:
Master/Installer
Installer Only
00 = clear event
03 = latch key report
06 = auto disarm
10 = display custom
words 8-
10
01 = device on/off
04 = forced STAY arm
07 = display “reminder”
11 = periodic test report
02 = user access
05 = forced AWAY arm
Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat
every
fourth week
VISTA-
15P/20P/SIA Program
Guide
50
Table of Device Addresses
This Device
Uses
Address
Reports as ††
Enabled By...
RF Receiver
00
100
∗
56 zone programming: input device type entry
AUI 1
(touchscreen)
01
n/a
automatic if AUI enable field
∗
189 enabled for AUI 1
AUI 2
(touchscreen)
02
n/a
automatic if AUI enable field
∗
189 enabled for AUI 2
AUI 3
(touchscreen)
(V20P)
05
n/a
automatic if AUI enable field
∗
189 enabled for AUI 3
AUI 4
(touchscreen)
(V20P)
06
n/a
automatic if AUI enable field
∗
189 enabled for AUI 4
Communications Device (LRR)
03
103
automatic if communications
device enabled in
menu mode
∗
29
4286 Voice Module
04
104
automatic if phone module access code field
∗
28 enabled
Zone Expanders (4219/4229):
Module
1 (for zones 09 -
16)
Module
2 (for zones 17 -
24)
Module
3 (for zones 25 -
32)
Module
4 (for
zones 33 -
40)
Module
5 (for
zones 41 -
48
)
07
08
09
(V20P)
10
(V20P)
11
(V20P)
107
108
109
110
111
∗
56 zone programming: input device type entry, then:
aut
omatic if zone no. 9-
16 entered as AW type or relay assigned
automatic if zone no. 17-
24 entered as AW type or relay assigned
automatic if zone no. 25-
32 entered as AW type or relay assigned
automatic if zone no. 33-
40 entered as AW type or relay assigned
automatic if zone no. 41-
48 entered as AW type or relay assigned
Relay Modules (4204):
Module 1
Module 2
Module 3
M
odule 4
12
13
14
(V20P)
15
(V20P)
112
113
114
115
∗
79 output device programming: device address prompt:
entered at device address prom
pt
entered at device address prompt
entered at device address prompt
entered at device address prompt
Keypads:
Keypad 1
Keypad 2
Keypad 3
Keypad 4
Keypad 5
Keypad 6
Keypad 7
Keypad 8
16
17
18
19
20
21
22
23
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
data
field programming as listed below:
always enabled, all sounds enabled.
data field
∗
190
data field
∗
191
data field
∗
192
data field
∗
193
data field
∗
194
data field
∗
195
data field
∗
196
RIS Communication
25
n/a
automatic
†† Addressable devices a
re identified by “1” plus the
device address when reporting. Enter report code for
zone 91 to enable device reporting (default = enabled).
See field
∗
199 for addressable device (ECP) 3-
digit/2-
digit identification keypad display options.
AUI devices are not supervised and therefore do not
report.
VISTA-
15P/20P/SIA Program
Guide
51
Compatible Devices
2
-
Wire Smoke Detectors
Sounders
Detector Type
Model No.
AB12M 10” Motorized Bell & Box
Photoelectric w/heat sensor
System Sensor 2WT
-
B
Photoelectric
System Sensor 2W
-
B
702 Outdoor Siren
Photoelectric
System Sensor 2151 w/B110LP
base
719 2
-
Channel Siren
713 High Power Speaker
Keypads
746 Indoor Speaker
Fixed
-
Word Keypad
6150
747
Indoor Sire
n
Alpha Keypad
6160
747PD Two
-
Tone Piezo Dynamic Indoor Siren
Voice Keypads
6150V, 6160V
747UL Indoor Siren
Touch Screen Keypad
6272, 6280, TUXEDO
748 Dual Tone Siren
Wireless Receivers
749 Speaker/Horn
Up to 8 transmitters
5881
EN
L
745VSD3
Voice Siren Driver
Up to 16 transmitters
5881
EN
M
Up to system max transmitters
5881
EN
H
Up to system max transmitters
5883
H
71
3 Speaker
WAVE Speaker
Keypad/Receivers
WAVE2 Two
-
Tone Siren
Up to 16 trans, fixed
-
word
6150RF
WAVE2PD Two
-
Tone Piezo Dynamic Siren
Up to system max trans, alpha
6160RF
5800WAVE Wireless Siren
Modules
System S
ensor
MHW
(beige)/;
MHW
(red) Indoor
Piezo Sounder
Wired Expan
der
Module
4219
Wired
Expan
der
/Relay
Module
4229
Relay Module
4204
Communication Device
AlarmNet 7847i, 7847i
-
E, LTE
-
iV, LTE
-iA, LTE
-XV, LTE-
XA,
LTE
-
XC,
Transformers
25VA, 16.5VAC Plug
-
In Trans
.
1321 (1321CN in Canada)
VISTA-
15P/20P/SIA Program
Guide
52
Agency Regulatory Statements
UL NOTICES
1. Entry Delay No. 1 and No. 2 (fields
∗
35,
∗
36) cannot be greater than 30 seconds for UL Residential Burglar Alarm installati
ons, and
entry delay plus dial delay should not exceed 1 minute. For UL Commercial Burglar Alarm installations, total entry delay may not
exceed 45 seconds.
2. For UL Commercial Burglar Alarm and UL Residential Burglar Alarm installations with line securit
y, total exit delay time must not
exceed 60 seconds.
3. The maximum number of reports per armed period (field
∗
93) must be set to “0” (unlimited) for UL installations.
4. Periodic testing (see scheduling mode) must be at least every 24 hours.
5. Alarm So
under plus Auxiliary Power currents must not exceed 600mA total for UL installations (Aux power 500mA max.).
6. All partitions must be owned and managed by the same person(s).
7. All partitions must be part of one building at one street address.
8. If used, the audible alarm device(s) must be placed where it/they can be heard by all partitions.
9. For UL commercial burglar alarm installations,
the control unit must be protected from unauthorized access. The tamper switch
installed to protect the control unit enclosure door is suitable for this purpose.
10.
Remote downloading without an alarm company technician on-
site (unattended downloading) is not permissible for UL installations.
11.
Auto-
disarming is not a UL Listed feature.
12.
As SIA li
mits for delay of alarm reporting and sounding can exceed UL limits for commercial and residential applications, the
following UL requirements per UL681 are provided:
The maximum time that a control unit shall be programmed to delay the transmission of a
signal to a remote monitoring location, or
to delay the energizing of a local alarm sounding device to permit the alarm system user to enter and disarm the system, or t
o arm
the system and exit shall not exceed:
a) 60 seconds for a system with standard l
ine security or encrypted line security,
b) 120 seconds for a system without standard line security or encrypted line security, or
c) 120 seconds for a system that does not transmit an alarm signal to a remote monitoring location.
13.
This control is not
intended for bank safe and vault applications.
14.
Vent zones are not for use in UL installations.
ULC S304 REQUIREMENTS (for VISTA
-15PCN and VISTA
-20PCN)
Refer to the following notes for systems intended for Low Risk Level (low extent of protection) and Medium Risk Level (medium
extent
of
protection) installations.
Low Risk Level
If the panel is used for Low Risk Level installations, the system must include the following:
•
Subscriber control unit may use one telephone number, but it must be programmed that
a)
it transmits over the single
channel to the receiver once every 24 hour;
b)
it detects a loss of communication and initiates the local trouble signal within 180 seconds;
c)
in event of failure in the communication channel, all alarm and trouble signals must be annunciated locally.
•
Protection circuit conductors shall form one fully supervised circuit so arranged that an alarm signal will be initiated at t
he central
station from the effect of loss data, an open circuit or other change in normal status.
•
Trouble response time must be in compliance with CAN/ULC
-S301, Central and Monitoring Station Burglar Alarm Systems
Medium Risk Level
If the panel is used for Medium Risk Level installations, the system must include the following:
•
Subscriber control unit may use at least two communication levels, one being the telephone number and the other being a radio
frequency communication channel –
the
Cell
communicator may be used. The Subscriber control unit must be programmed that
a)
it transmits over the both channels to the receiver
once every 24 hours;
b)
failure of communication of either channel is reported to the Central Station on the other channel within 240 sec;
c)
the first attempt to send a status change signal shall utilize the Telephone line. Where it is known to have failed, transmission
attempts over the alternate communication channel shall occur.
•
Protection circuit conductors shall form double fully supervised circuits so arranged that an alarm signal will be initiated
at the central
station from the effect of loss data, an open circuit or other change in normal status.
•
Trouble response time must be in compliance with CAN/ULC
-S301, Central and Monitoring Station Burglar Alarm Systems
Perimeter, Space, Safe, and Vaults Protection
Protection for perimeter, space, safe, and vaults need to be provided during the installation.
•
For the Low Risk Security Level –
Accessible openings should be contacted whether fixed or moveable;
•
For the Medium Risk Security Level –
All moveable and fixed accessible openings should be c
ontacted.
VISTA-
15P/20P/SIA Program
Guide
53
SIA Quick Reference Guide
SIA QUICK REFERENCE GUIDE
1.
∗
31 Single Alarm Sounding per Zone: If “0” selected, “alarm sounding per zone” will be the same as the “number of reports in armed
period” set in field
∗
93 (1 if one report, 2 if 2 reports,
unlimited for zones in zone list 7).
2.
∗
34 Exit Delay: Minimum exit delay is 45 seconds.
3.
∗
35/*36 Entry Delay 1 and 2: Minimum entry delay is 30 seconds.
4.
∗
37 Audible Exit Warning: Feature always enabled; field does not exist.
5.
∗
39 Power Up in Prev
ious State: Must be “1,” power up in previous state.
6.
∗
40 PABX Access Code or Call Waiting Disable: If call waiting is used, call waiting disable option in field *91 must be set.
7.
∗
50 Burglary Dial Delay: Delay must be minimum of 30 seconds.
8.
∗
59 Exi
t Error Alarm Report Code: Always enabled.
9
∗
68 Cancel Report Code: Default is “code enabled.”
10.
∗
69 Recent Closing Report Code: Always enabled.
11.
∗
91 Option Selection: Exit Delay option should be enabled. If call waiting is used, Call Waiting Disable
must be set to “1” (enabled).
12.
∗
93 No. reports in Armed Period: Must be set for 1 or 2 report pairs.
13.
Cross zone timer programming is set in field
∗
85; cross zone pairs are assigned in zone list 4 using
∗
81 Zone List mode.
14.
Duress code is assigned by using the “add a user code” procedure found in the User Guide. Enable Duress code reporting by
programming zone 92 using
∗
56 Zone Programming mode.
15.
Fire alarm verification is a built
-in system feature when a zone is programmed for zone type 16.
VISTA-
15P/20P/SIA Program
Guide
54
FCC S
tatements
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or U
ser's Manual. Unauthorized changes
or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following stat
ement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions,
may cause interference to radio and television reception. It has been type tested and found to comply with t
he limits for a Class B computing device in accordance
with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interferenc
e in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch c
ircuits.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES
-003.
Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.
FCC/IC STATEMENT
This device complies with Part 15 of the FCC rules and RSS 210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suiv
antes: (1)
Cet appareil ne doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception
indésirable.
TELEPHONE/MODEM INTERFACE
FCC Part 68
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC
registration number and Ringer
Equivalence Number (REN). You must provide this information to the telephone company when requested.
This equipment uses the following USOC jack: RJ31X
This equipment may not be used on telephone-
company
-provided coin service. Connection to party lines is subject to state tariffs. This equipment is hearing-
aid
compatible.
Industry Canada
NOTICE
: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunicati
ons network protective,
operational
and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment,
or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and
internal metallic water pipe system, if
present, are connected together, This precaution may be particularly important in rural areas.
Caution
: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as appropriate.
Ringer E
quivalence Number Notice:
The
Ringer Equivalence Number
(REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any c
ombination of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed 5.
Industrie Canada
AVIS:
l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et
de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relativ
es au matériel terminal. Le
Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterpris
e locale de télécommunication. Le matériel doit
également être ins
tallé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions
énoncées ci
-dessus n’empêche pas la dégradation du service dans certaines situations.
Les réparations de matériel nomol
ogué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications peut
demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur
ou à cause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques et des canalisations
d’eau métalliques, s’il y en a, sont raccordés ensemble.
Cette précaution est particulièrement importante dans les régions rurales.
Avertissement :
L’utilisateur ne doit pas tenter de faire ces raccordements lui
-même; il doit avoir racours à un service d’inspection des installations électriques, ou à
un électr
icien, selon le cas.
AVIS : L’indice d’équivalence de la sonnerie
(IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une
interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices
d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
VISTA-
15P/20P/SIA Program
Guide
55
Limitations Statement
WARNING
THE LIMITATIONS OF THIS ALARM SYSTEM
While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other
emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of
reasons. For example:
•
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or
disconnect an alarm warning device.
•
Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without
power. Battery
-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly.
Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.
•
Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the
signal path has been recently checked during a weekly test, blockage can occur if a metal object is m
oved into the path.
•
A user may not be able to reach a panic or emergency button quickly enough.
•
While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or
provide early warning for a v
ariety of reasons in as many as 35% of all fires, according to data published by the Federal
Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are
as follows. Smoke detectors may have been im
properly installed and positioned. Smoke detectors may not sense fires that start
where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke
detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not
sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every ki
nd
of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like
smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits,
children playing with matches, or arson. Depending on the nature of the fire and/or location of the smoke detectors, the
detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent
injury or death.
•
Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation
manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and
intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes
place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking,
painting or spraying of any material on the mirrors, w
indows or any part of the optical system can reduce their detection ability.
Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area
approaches the temperature range of 90° to 105°F (32° to 40°C), the detection performance can decrease.
•
Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other
side of closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, then
they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the
alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or
by passing traffic. Finally, alarm warning
devices, however loud, may not warn hearing-
impaired people.
•
Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or
temporarily out of service.
Telephone lines are also subject to compromise by sophisticated intruders.
•
Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately.
•
This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to las
t as
long as 10 years, the electronic components could fail at any t
ime.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm
system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and rem
ote
keypad) should be tested as well.
Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions.
Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device
being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the
actual battery life in a given installation. This wireless system, however, can identify a true
low
-battery situation, thus allowing time
to arrange a change of battery to maintain protection for that given point within the system.
Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substit
ute for
insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to
insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to
learn about these developments.
VISTA-
15P/20P/SIA Program
Guide
56
Contacting Technical Support
PLEASE, before you call Technical Support, be sure you:
• READ THE INSTRUCTIONS!
• Check all wiring connections.
• Determine that the power supply and/or backup battery are supplying proper voltages.
• Verify your programming information where applicable.
• Note the proper model number of this product, and the version level (if known) along with any documentation that
came with the product.
• Note your
customer number and/or company name.
Having this information handy will make it easier for us to serve you quickly and effectively.
Resideo Technical Support: 1-
800-
645-
7492
•
Monday
-Friday, 8:30 a.m. to *8:00 p.m. EST: s
upport available for all intrusion products
.
*(between 5pm and 8pm some non-
vista products are not supported)
•
Monday
-Friday, 8:00 p.m. to 9:00 p.m. EST: support available for all Lynx series and Vista-
Plus residential control
panels.
•
Saturday, 9:00 a.m.
to 5:30 p.m. EST: support available for all Lynx series and Vista-
Plus residential control panels.
AlarmNet Technical
Support:
1-800-
222-
6525
•
Monday
-Friday, 8:00 a.m. to *9:00 p.m. EST: support available for all AlarmNet products and Services
*(between
6:00 p.m. and 9:00 p.m. some AlarmNet products are not supported)
•
Saturday, 9:00 a.m. to 5:30 p.m. EST: support available is limited to AlarmNet cell communicators
MyWebTech:
https://mywebtech.honeywellhome.com/Intrusion/Home#
VISTA-
15P/20P/SIA Program
Guide
57
5800
Series Transmitter Input Loop Identification
All
of the transmitters illustrated have one or more unique factory assigned input (loop) ID numbers.
Each of the inputs
requires its own programming zone
(e.g., a 583
4-4's four inputs require four programming zones). For information on any
transmitter not shown, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc.
UL NOTE
: The following transmitters are not intended for use in UL installations: 5804BD, 5814, 5816TEMP, 5819,
5819WHS
and
5819BRS.
VISTA-
15P/20P/SIA Program
Guide
58
NOTES
VISTA-
15P/20P/SIA Program
Guide
59
NOTES
VISTA-
15P/20P/SIA Program
Guide
SUPPORT, WARRANTY, & PATENT INFORMATION
For the latest warranty information, please go to:
https://www.security.honeywellhome.com/hsc/resources/wa/index.html
For patent information, please go to:
https://www.resideo.com/patent
For the latest documentation and additional information, please go to:
https://mywebtech.honeywellhome.com
Warranty
Patents
MyWebTech
The product should not be disposed of with other household waste. Check for the nearest authorized collection
centers or authorized recyclers. The correct di
sposal of end-
of-life equipment will help prevent potential negative
consequences for the environment and human health.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2019 Resideo Technologies, Inc
.
www.resideo.com
ÊK5305
-
1PRV9ÆŠ
The Honeywell Home Trademark is used under
License from Honeywell International Inc.
K5305-
1PRV
9 3/15
Rev
B
- Uploaded