Which Image Sensor Is Compatible With My Panel?
There are four different versions of the ADC Image sensor. To confuse matters further, some manufacturers re-brand the ADC Image sensor with their own part number and then market it separately. The matrix below is intended to take the guesswork out of checking Image sensor compatibility.
Product Identification and Compatibility Matrix
| Product Name | Identification | Compatible Panels |
|---|---|---|
| ADC-IS-100-GC | Blue Label | 2GIG Go!Control |
| ADC-IS-200-GC | Blue Label | 2GIG Go!Control |
| ADC-IS-100-LP | Silver Label |
Interlogix Simon XT 1.3+
Interlogix Simon XTi 1.0+
Interlogix Simon XTi-5
Interlogix Concord 4
DSC Impassa DSC PowerSeries Neo DSC Touch Qolsys IQ Panel Qolsys IQ Panel 2 Qolsys IQ Panel 2 Plus* 2GIG GC3 Note: GE Image Sensors are also used with DSC panels |
|
ADC-IS-200-LP ADC-IS-221-LP |
Orange Label | |
|
ADC-IS-200-IQ ADC-IS-221-IQ |
|
Qolsys IQ Panel Qolsys IQ Panel 2 Qolsys IQ Panel 2 Plus* |
*The Qolsys IQ Panel 2 Plus comes with support for PowerG sensors. The PowerG daughterboard uses the same antenna required by the Image Sensor daughterboard. For this reason, ADC lists the IQ Panel 2 plus as not compatible with Image Sensors. However, as long as only one technology or the other is used, the IQ Panel 2 Plus can use Image Sensors. In addition, there are two PowerG Image Sensors available. The PG9934P and the PG9944. These image sensors can work with Alarm.com.
Panel Hardware Requirements and Number of Devices Supported
| Panel Type | Hardware Requirements | Compatible Image Sensors | Image Sensor Limit |
|---|---|---|---|
| Interlogix Simon XT | Panel Version 1.3+
Alarm.com modules between versions 146 - 185 require an Image Sensor daughterboard to be installed. Zone 39 must be reserved for the Image Sensor daughterboard, which is hardwired to the panel. Alarm.com modules with version 187+ are compatible and include support for the Image Sensor. Alarm.com modules between versions 146 - 185 require an Image Sensor daughterboard to be installed. Zone 39 must be reserved for the Image Sensor daughterboard, which is hardwired to the panel. |
ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Three per panel |
| Interlogix Simon XTi | Panel version 1.0+
Alarm.com modules between versions 151 - 185 require an Image Sensor daughterboard to be added. Alarm.com modules with version 187+ are compatible and include Image Sensor support, with no daughterboard needed. |
ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Three per panel |
| Interlogix Simon XTi-5 | All panel versions are compatible.
Alarm.com module version 177 - 185 require an Image Sensor daughterboard to be added. Alarm.com modules with version 187+ have built-in Image Sensor support. |
ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Three per panel |
| Interlogix Concord | Panel version 4.0+
Alarm.com module version 177+ on CDMA, or 173+ on HSPA with an image Sensor daughterboard version 104.0+ attached to the module. Note: Image Sensors are not supported in the original release of the Concord module version 187. Future functionality will be brought via an Over-The Air (OTA) firmware update. No daughterboard is required. |
ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Three per panel |
|
2GIG Go!Control 2GIG GC2e |
Panel firmware version 1.10+
The 900 MHz XCVR2 transceiver must be installed in the panel.
|
ADC-IS-100-LP (2GIG IMAGE1) ADC-IS-200-LP (2GIG IMAGE2) ADC-IS-221-LP ADC-IS-300-LP (2GIG IMAGE3) |
Three per panel |
|
2GIG GC3 2GIG GC3e |
Panel version 3.0.1+ The 2GIG XCVR3 Transceiver Adapter for the Image Sensor must be installed. | ADC-IS-100-LP (2GIG IMAGE1) ADC-IS-200-LP (2GIG IMAGE2) ADC-IS-221-LP ADC-IS-300-LP (2GIG IMAGE3) |
Ten per panel |
| Qolsys IQ Panel | All firmware versions of the Qolsys IQ Panel are compatible. Image Sensor compatibility is built-in. | ADC-IS-100-LP (QZ8100-840) ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP (QZ8103-840) |
Five per panel |
| Qolsys IQ Panel 2 & Panel 2 Plus* see note above this chart | All Firmware versions of the Qolsys IQ Panel 2 are compatible.
Requires the Qolsys Image Sensor daughterboard. PowerG Image Sensors (PG9934P & PG9944) can be used w/ IQ2+. No Qolsys Image Sensor Daughterboard is required. See this post for more info. |
ADC-IS-100-LP (QZ8100-840) ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP (QZ8103-840) DSC PG9934P (IQ2+ Only) DSC PG9944 (IQ2+ Only) |
Five per panel |
| DSC Touch | All firmware versions of the DSC Touch are compatible. Compatibility is built-in, no daughterboard required |
ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Five per panel |
| DSC Impassa | Panel version 1.3+ Requires an Alarm.com module that comes with the Image Sensor daughterboard attached. SKU’s for these modules are 3G8055(I) or CD8055(I) | ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Three per panel |
| DSC PowerSeries Neo | Panel version 1.10+
Alarm.com module versions 185 and lower must come with the Image Sensor daughterboard attached. SKU’s for these modules are 3G8080(I) or CD8080(I). Alarm.com modules with version 187+ are compatible with no Image Sensor daughterboard attached. |
ADC-IS-100-LP ADC-IS-200-LP ADC-IS-221-LP ADC-IS-300-LP |
Three per panel |
Did you find this answer useful?
We offer alarm monitoring as low as $10 / month
Click Here to Learn More
Hello Larry, I found this information from Alarm.com regarding the GC2e panel version 1.23.
The following are required to enroll Image Sensors in a 2GIG GC2e panel:
1. A customer account has been created with Alarm.com and has a package that includes an Images add-on. ***(ADT may not support this feature).***
2. The Alarm.com module and XCVR5e transceiver are installed properly in the GC2e.
3. A cell phone test has been performed successfully and the panel is communicating.
*** Important: *** The 2GIG GC2e only supports the Image Sensor version 3 (ADC-IS-300-LP). ***
I hope this info Helps.
I have a GC-2e panel (firmawre v1.23) monitored by ADT, who told me they do NOT support image sensors. However, the GC-2e, with the appropriate Image sensor and the XCVR2e module, will support an image sensor. The iPhone app is linked to Alarm. com. If I get the right image sensor and the XCVR2e module, will Alarm.com display the image if the sensor is triggered, or is the fact that ADT "does not support" image sensors preclude the upload from happening?
Related Products
2GIG IMAGE3
Image Sensor for GC3, GC3e, & Edge
Interlogix 600-9400-IMAG
Alarm.com Image Sensor
Interlogix 600-9400-IMAG-KIT
Alarm.com Image Sensor w/ Daughterboard
Qolsys QZ8103-840 Image Sensor
Alarm.com Image Sensor Compatible w/ Qolsys IQ & IQ Panel 2
2GIG IMAGE2
Image Sensor for GC3 & GC3e
Alarm.com ADC-IS-DB
Image Sensor Daughter Board from Alarm.com
2GIG IMAGE1
PIR Motion Detector with Integrated Still Camera
Related Videos
Related Categories
- Answered
- Answered By
- Julia Ross