System Sensor RRS-MOD with 4-Wire i3™ Smokes on a VISTA-20P

-
1

-
Step
-by-Step


Tech Support

Updated 7/12/13

Vista-20P / FA168C Family w/RRS-Mod & 4-
wire Smokes

Wiring:
Sample shows Zone 2 for 4
-Wire Smoke Detectors.

Fire Zone Reset:

Using a 4204 we can
program the panel to do a fire zone reset:

*79 Programming:







01 Relay Position?

1-4

01
01 Module Addr?

07-
15
12

Enter Output No.

00 = QUIT

00
01 Output Type?

Realy


1
Enter Output No.

00 = QUIT

01 -
2

-
Step
-by-Step


Tech Support

Updated 7/12/13

*8
0 Programming:













U
sing Additional Fire Zones:


If you have another fire zone, or are using Keypad Fire Panic, these also will trip the RRS
-MOD.

When using a EOL supervision Relay, t
he pulsing RRS
-MOD
( witho
ut a latched smoke
detector
) w
ill
cau
se rapid Trouble/Restore reporting to C.S. W
hen the RRS
-MOD starts to pulse the zone will report to
the panel a trouble on an open then a restore on close,
and will do this for the duration of the sounder. The
logic of
the panel tells the dialer to report every T
rouble and every R
estore. This means
every time it
pulses it sends a signal to the dialer queue
, caus
ing
multiple
Trouble reports to be sent to C
entral
Station.

To prevent these repeat Trouble
reports when oth
er Fire Zones are tripped, you
can
wire one of the triggers
to the positive side of fire zone (zone 2 in our case)
, and
program the
trigger to activate upon “Alarm” of
these other zones in a Zone List. When one of these zones trip, the trigger will hold a
short to ground on
Zone
2, putting it into Alarm and preventing it from responding to the pulsing of the RRS
-MOD.
*79 Programming:





Output Funct. #

(00 = Quit)

00
Output #?

Relay 01

01
01
Zo
ne Type

54
01 Activated by:

Zone
Type

2
01 A E P Trig

?00 0 0 -
ZL=1

Output Funct. #

(00 = Quit)

01
Enter Output No.

00 = QUIT

00
17 Out Normal Low?

0=No, 1=Yes

0
Enter Output No.

00 = QUIT

17
Trigger 1 = Output # 17

Trigger 2 = Output # 18
-
3

-
Step
-by-Step


Tech Support

Updated 7/12/13

*80 Programming:

































*8
1 Programming:








If zone 2 is entered in this Zone List it will cause the LED of the Smokes on Zone 2 NOT
to
Latch on Alarm!
01 Enter Zn Num.

(00 = Quit)

00
01 Enter Zn Num.

(00 = Quit)

95
01 Enter Zn Num.

(00 = Quit)

02
Zone list No.

(00 = Quit)

01
Output Funct. #

(00 = Quit)

00
Output Funct. #

(00 = Quit)

00
Output #?

17
0
3

Output Action

Off

0
0
3

Enter Zone Type

Disarming

22
0
3

Activated by:

Zone Type

2
02 A E P Trig

?00 0 0 -
ZL=
1
Output Funct. #

(00 = Quit)

03
Output #?

17
0
2

Output Action

Stay Closed

02
Enter Event

Alarm

1
0
2

Zone List

01
0
2

Activated by:

Zone List

1
0
2

A
E P Trig

?00 0 0 -
ZL=1

Output Funct. #

(00 = Quit)

02
Heat Zone

P
anic Zone