How Do I Program a 4193SN to a VISTA-128BPT, 250BPT, or VISTA-50?
When programming the 4193SN, the user must first determine if one or both loops will be used. Following the steps below, program the zone(s) into the system. Programming and connection of the device should occur at the same time, otherwise issues such as trouble display will arise.
When using the 4193SN, Loop 1 must always be used. If Loop 1 is used, then Loop 2 can also be used. If only using one input on the 4193SN, it must be Loop 1.
- Enter programming. Enter Installer Code (Default = 4140) + 8 + 00 (Vista-50), or Installer Code + 8 + 000 (Vista-128BPT or Vista-250BPT). Press #93.
- "Zone Prog?" prompt - Press 1 for yes.
- "Set to Confirm?" prompt - Press 0 for no.
- "Enter Zone No." prompt - Press the 2 or 3 digit zone number you wish to program (Vista-50 uses 2 digit zone numbers, Vista-128BPT and Vista-250BPT use 3 digit). Press * to move through programming screens.
- Enter the appropriate information for Zone Type, Partition, and Report Code.
- "Input Type" prompt - Enter 06 for Serial # Polling, then press *.
- Enter the Serial Number assigned to the 4193SN, OR fault and restore the zone connected to the proper input loop to learn in the serial number. Learning in the SN will only be possible when about 20 or fewer devices are connected to the polling loop. If there are more than 20 connected, there's a good chance another zone's serial number will check in while you're trying to make your entry. You will then have to delete and re-learn. Press *.
- Enter loop number 1 or 2. Press *. You should see a summary screen that shows the programming you've made. Press * to move on if programming the VISTA-50. This will advance you to the next zone number.
- "Smart Contact?" prompt - Press 0 for no.
- "Anti-Mask?" prompt - Press 0 for no.
- "V-Plex Relay?" prompt - Press 0 for no.
- "Enter Zone No." prompt - Press 00 or 000, then *.
- "Quit Menu Mode?" prompt - Press 1 for yes.
- Exit programming. Press *99.
Did you find this answer useful?
We offer alarm monitoring as low as $10 / month
Click Here to Learn More
Are there different directions if I need to replace one of the 4193SN modules?
Dalton, on the 4193SN's where you're using the Green and Black wires, are you also using Loop 1 of that 4193SN for a different zone? You can only use Loop 2 (green + black) on the 4193SN if you're already using Loop 1 (either White + Black with EOLR, or Yellow and Black with Normally Closed device). If you want to use these doors as NC with no resistor, and you're not already using Loop 1 on that device, wire to Yellow and Black instead of Green and Black and change the programming to point to Loop 1.
I have followed the instructions on how to program a 4193SN in to the vist 128 i have several zone 9 to 13 program 3 are doors wired to geen on the 4193sn
2 a hold up buttons wired to the white with eol in place i turn chime on with the installer code+9 when i tip a door or one of the hold up buttons the faults do not register in the panel.
plz help
Related Products
Related Categories
- Wired Alarm Control Panels
- Wired Security Systems
- Wired Door & Window Alarm Contacts
- Wired Environmental Sensors
- Wired Glass Break Detectors
- Wired Motion Detecting Sensors
- Wired Heat Detectors
- Wired Smoke Detectors
- DIY Wired Security Systems
- Wired Garage Door Alarm Sensors
- Answered
- Answered By
- Julia Ross