Defaulting SiX and PROSIX Devices - New Version - 2021

STEPS TO DEFAULT SiX

and PROS
i
X

SERIES
DEVICES


Defaulting a device may be necessary
if the
device is

enroll
ed

in

a panel
(paired with a panel)
in a
location that is different than the
intended
panel
,

and the installer does not have access to the
unintended
panel to delete the sensor.


Each device
provides

visual indicat
ion

showing whether or not

it is paired with a controller. This is
described in the table below

for each device
.


The procedure to default each device is primarily the same

(except
for
the keypad and key fob)
: Open
the device cover, remove the battery, activate the tamper switch, a
nd then reinstall the battery while
the tamper switch is still held down.


For devices other than the SiXFOB
/PROSIXFOB
, t
his process is available for 24 hours after enrollment
with the panel and while the
device remains powered

(battery installed

in sensors; AC power applied at
keypad)
.

For the SixFOB
/PROSIXFOB
, this process expires after the first 100 transmissions.


PROCEDURES

MODEL

DEFAULT PROCEDURE

PAIRED/NOT PAIRED INDICATION

SiXCT

SiXMINICT

SiXGB

PROSIXMINI

PROSIXMINI2

PROSIXGB

PROSIXCT

PROSIXFLOOD

PROSIXSHOCK

PROSIXTEMP

1.

M
ake sure the transmitter is on the base
mount
ing

bracket. Remove the Cover and
battery.

2.
Press and hold the tamper switch,
Install the battery and continue to hold
the tamper
switch.

3.
After a couple of seconds LED will flash
rapidly


Indicator

Paired

Not Paired

Green LED

slow blink
when tamper
faulted

fast
blinking

when
tamper
faulted




SiXSIREN

SiXSIRENOD

PROSIXSIREN

PROSIXSIRENO

1.

Remove the Baseplate.

2.

Remove the
batteries.

3.

Hold the tamper switch down.

4.

Reinstall the batteries while still holding
the tamper switch
down

(recommended
15
-
30 sec)
.


Indicator

Paired

Not Paired

Green LED

slow blink
when tamper
faulted

fast
blinking

when
tamper
faulted




SiXSMOKE

SIXSMOKE
-
CN


1.

Remove

the
baseplate.

2.

Remove the batteries.

3.

Activate the tamper with a magnet.

4.

Reinstall the batteries while still
activating the tamper switch.


Indicator

Paired

Not Paired

Green LED

slow blink
when tamper
faulted

fast
blinking

when
tamper
faulted




SiXPIR

PROSIXPIR

1.

Open the cover.

2.

Remove the battery.

3.

Hold the tamper switch down.

4.

Reinstall the battery while still holding
the tamper switch down.


Indicator

Paired

Not Paired

Green LED

slow blink
when tamper
faulted

fast
blinking

when
tamper
faulted




LKP500
-
EN

LKP500
-
ENC

(
LYRIC

KEYPAD)

1.

Press the 3 key until the advanced
menu is displayed

2.

Scroll until
“
Default
”

is displayed.

3.

Press select.


Indicator

Paired

Not Paired

Status icon

slow blink

fast
blinking

















SiXFOB

PROSIXFOB

1.
Press and hold the three white buttons
simultaneously for
more than five (5)
seconds.

This process is available for the
first 100 transmissions from the key fob.

Indicator

Paired

Not
Paired

both

LEDs

LEDs no
t

blinking

when
both top
buttons are
pressed

alternating,
fast
blinking

when both
top buttons
are pressed


PROSIXLCDKP

1.

Press and hold the [3] key until
"Programming Mode” is displayed

2.

Press the Scroll [3] key to
scroll to
Default Keypad, press 2 to Confirm or *
to abort
.



Indicator

Paired

Not Paired

Status icon
and trouble
led

System status
is displayed

Alternate
blinking
,
display will
show
"press any
key to pair
with
system


PROSIXRPTR

1.

Open the cover

and verify device is
powered on
.

2
.

Hold the tamper switch
for ½ seconds
and repeat four times (for a total of
five)
.

4.

All three LEDS rapidly flash leaving only
the Power LED on
.

Indicator

Paired

Not Paired

All 3
LEDs

Green

LEDs no
t

blinking


Only
the
Power LED
is on

and
all scroll
when
tampered


PROSIXHEATV

PROSIXSMOKEV

1.

Remove the Detector from the
Base and remove the Batteries
.

2.

Flip the Tamper switch to the 'non
tampered' position.

3.

Install the batteries.

4.

Watch the green LED for a rapid
flash.

5.

Remove the batteries and set the
tamper switch back to the
'Tampered' position
.

Indicator

Paired

Not Paired

Green LED

Slow blink
when
tampered


Fast
blinking

when
tampered


PROSIXC2W


1.

Open the cover

and verify device is
powered on
.

2
.

Simultaneously press and release the
calibration and tamper switches.

4.

The Green enrollment LED rapidly
flashes and the PROSIXC2W defaults
.


Indicator

Paired

Not Paired

LED

#1

Slow blink
when
tampered


Fast
blinking
when
tampered



PROSIXCOMBO

PROSIXCOMBOC

SIXCOMBO

SIXCOMBO
-
CN

1. Press and hold both the Smoke and CO
test switches simultaneously until the
welcome message announces, then
release.

2. Wait for green LED to flash rapid
l
y.

3. Press and hold
both switches again for
one second and release.

4. LED blinks rapidly for 15 seconds.

OR

1.

Remove

the
base Plate and
Remove
the batteries.

3.

Activate the tamper with a magnet.

4.Reinstall the batteries while still
activating the tamper switch.

Indicator

Paired

Not Paired

Green LED

Slow blink
when
tampered


Fast
blinking
when
tampered

PROSIXCO

PROSIXCOCN

1. Remove batteries from the detector

2. Press the CO Test Button.

3. While holding the
CO
test button, insert
the batteries.
Continue hold the test
button for 5 seconds and release.

4. The status LED should start blinking
green rapidly.

Indicator

Paired

Not Paired

Green LED

Slow blink
when
tampered


Fast
blinking
when
tampered


P
ROSIXMED

1.

Press and hold button for 15
seconds.
When successful, the LED comes back on
flashing.

Indicator

Paired

Not Paired

Green LED

Fast blinking
for 2 seconds
when pressed
for 2 seconds

Fast
blinking for
20 seconds
when
pressed for
2 seconds


PROSIXPANIC

1.

Press and hold

BOTH

button
s

for 15
seconds. When successful, the LED comes
back on flashing.

Indicator

Paired

Not Paired

Green LED

Fast blinking
for 2 seconds
when pressed
for 2 seconds

Fast
blinking for
20 seconds
when
pressed for
2 seconds


PROWLTOUCH

PROINDMV

These devices are

not SiXRF device
s

that lock to a Panel.
They

can be
paired to a different control panel
without
be
ing

delet
ed
from the current
control panel.

They do not have a
default option