2GIG Edge w/ AT&T LTE Frequently Asked Questions
What Is the Default Installer Code on a 2GIG Edge?
The default Installer Code for the 2GIG Edge is 1561. This code is used to access the Installer Toolbox and program the system. Keep reading for full info.
How Do I Use the GoControl! GD00Z Garage Door Controller With My Alarm Panel
To use the GoControl! GD00Z Garage Door Controller with your alarm panel, the panel must have a built-in Z-Wave controller. Come, learn how this is done.
Does a Google Nest Thermostat Work w/ a 2GIG Edge?
A Google Nest Thermostat will integrate with Alarm.com, also the 2gig Edge panel works on Alarm.com. Check out this article to see how they operate together.
How Do I Add a High Current Siren to a 2GIG Edge?
The 2GIG Edge has a bell output, providing 120 mA of current. If you need a higher current siren, you must add a relay and power supply. Read on to learn more.
How Do I Upgrade My 2GIG Edge Panel's Firmware?
The 2GIG Edge can be updated using a USB drive, or over-the-air (OTA) via Alarm.com. OTA updates via WIFI are free and updates via cellular incur a small charge. Learn more!
What is the Default Master Code On a 2GIG Edge?
The 2GIG Edge has a default Master Code of 1111. This code is almost always changed for security purposes. Learn about the 2GIG Edge Master Code and how to change it.
Does the 2GIG Edge Support Z-Wave?
There is a Z-Wave Plus V2 700-Series Z-Wave Controller inside every 2GIG Edge. It is used for pairing with devices like lights, locks, and thermostats. Check out 2GIG Edge Z-Wave.
How Do I Program an Image Sensor to a 2GIG Edge?
The 2GIG Edge supports the 2GIG IMAGE3 Image Sensor after a 2GIG XCVR3-GC3 Module has been installed. Learn how to program an image sensor to the 2GIG Edge Security System.
How Do I Install the XCVR3-GC3 to a 2GIG Edge?
The 2GIG XCVR3-GC3 connects with terminals GND, AUX+ (DCOUT+), TX, and RX on the 2GIG Edge. The module provides image sensor support. Learn to install the XCVR3-GC3 with the Edge.
Is the 2GIG Edge Compatible With All 2GIG Sensors?
The 2GIG Edge works with all 2GIG Sensors, including the non-encrypted 2GIG 345 MHz Sensors and the encrypted 2GIG eSeries Sensors. Learn about 2GIG Edge Sensor compatibility.
The default Installer Code for the 2GIG Edge is 1561. This code is used to access the Installer Toolbox and program the system. Keep reading for full info.
Added:
How Do I Use the GoControl! GD00Z Garage Door Controller With My Alarm Panel
To use the GoControl! GD00Z Garage Door Controller with your alarm panel, the panel must have a built-in Z-Wave controller. Come, learn how this is done.
Added:
Does a Google Nest Thermostat Work w/ a 2GIG Edge?
A Google Nest Thermostat will integrate with Alarm.com, also the 2gig Edge panel works on Alarm.com. Check out this article to see how they operate together.
Added:
How Do I Add a High Current Siren to a 2GIG Edge?
The 2GIG Edge has a bell output, providing 120 mA of current. If you need a higher current siren, you must add a relay and power supply. Read on to learn more.
Added:
How Do I Upgrade My 2GIG Edge Panel's Firmware?
The 2GIG Edge can be updated using a USB drive, or over-the-air (OTA) via Alarm.com. OTA updates via WIFI are free and updates via cellular incur a small charge. Learn more!
Added:
What is the Default Master Code On a 2GIG Edge?
The 2GIG Edge has a default Master Code of 1111. This code is almost always changed for security purposes. Learn about the 2GIG Edge Master Code and how to change it.
Added:
Does the 2GIG Edge Support Z-Wave?
There is a Z-Wave Plus V2 700-Series Z-Wave Controller inside every 2GIG Edge. It is used for pairing with devices like lights, locks, and thermostats. Check out 2GIG Edge Z-Wave.
Added:
How Do I Program an Image Sensor to a 2GIG Edge?
The 2GIG Edge supports the 2GIG IMAGE3 Image Sensor after a 2GIG XCVR3-GC3 Module has been installed. Learn how to program an image sensor to the 2GIG Edge Security System.
Added:
How Do I Install the XCVR3-GC3 to a 2GIG Edge?
The 2GIG XCVR3-GC3 connects with terminals GND, AUX+ (DCOUT+), TX, and RX on the 2GIG Edge. The module provides image sensor support. Learn to install the XCVR3-GC3 with the Edge.
Added:
Is the 2GIG Edge Compatible With All 2GIG Sensors?
The 2GIG Edge works with all 2GIG Sensors, including the non-encrypted 2GIG 345 MHz Sensors and the encrypted 2GIG eSeries Sensors. Learn about 2GIG Edge Sensor compatibility.
Added: