Qolsys S-Line IQ Water Valve Kit Posts

FortrezZ is discontinuing another of its Z-Wave products due to its inability to source some required components. For this reason, Alarm.com no longer recommends its installation. Installed units will continue to work, and Alarm.com will continue to offer troubleshooting support for them.

This may be the result of the supply chain issues experienced a few years ago. FortrezZ was forced to discontinue the MIMOlite some time ago, and now we're seeing the discontinuation of their Water Valve. Products already purchased and/or installed are not affected by this news.

If you already have a FortrezZ Water Valve (WV-01) but haven't installed it yet, no worries. It should still install and operate as expected. If you have any problems related to integrating the water valve with Alarm.com, you can still get assistance from tech support. If you are an Alarm Grid monitoring customer, we offer free technical support as well.

If you were thinking of purchasing a FortrezZ Water Valve, but missed the opportunity, you have other options available. We offer the Alarm.com Z-Wave Plus Smart Water Valve and Meter, and the Alarm.com Z-Wave Plus Smart Water Valve. The Alarm.com smart water valves use Z-Wave Plus and can be used with any Alarm.com compatible panel that supports Z-Wave or Z-Wave Plus.

Left, Alarm.com Z-Wave Plus Smart Water Valve with Meter. Right, Alarm.com Z-Wave Plus Smart Water Valve:

In addition to the Alarm.com options, we also offer the Qolsys IQ Water Valve. It's available in two (2) separate kits. The PowerG Kit offers the IQ Water Valve with two (2) DSC PG9985 Flood Sensors. The S-Line Kit offers the water valve with three (3) Qolsys IQ Flood-S 319.5 MHz S-Line Flood Sensors. If purchasing one of these kits, be sure to take into account what panel the kit is meant to work with. All Qolsys IQ Panel 4 versions can support PowerG while only some can support 319.5 MHz S-Line sensors.

Below left, IQ Water Valve w/ Qolsys S-Line Flood Sensors. Right, IQ Water Valve w/ PowerG Flood Sensors:

A smart water valve is most advantageous when used in conjunction with flood sensors. If a water leak is detected by a sensor, it can alert the alarm system. Then, the system can use that information to run a rule or scene to automatically shut off the water main to the home or business. Having this type of protection can save on homeowner's insurance premiums, and can prevent widespread damage and loss to your home or business.

Specifications for Alarm.com ADC-SWM150:

• Device Type: Z-Wave Plus Smart Water Valve and Meter
• Power: 100-240VAC
• Operating Temperature: 14°F to 185°F
• Indoor/Outdoor: Indoor Use Only
• Valve Size: 1"
• Valve Threads: Male NPT
• Valve Portability: NSF/ANSI 61 and 372 Standards
• Control Unit Dimensions: 2.75"L x 4.0"W x 1.25"D
• Meter and Valve Dimensions: 11"L x 5.75"W x 3.75"D
• Actuator and Valve Dimensions: 2.0"L x 4.5"W x 3.75"D
• Maximum Compatible Pipe Size: 1.25"
• Power Supply Cable Length: 19.7 Feet
• Package Contents: Control Unit, Valve & Meter, Enclosure, Power Adapter, Manual Shut-Off Handle, Cable Ties (x5), Wall Bracket, Wall Anchors (x2), Screws (x2)

Specifications for Alarm.com ADC-SWV100:

• Power: 100 - 240 VAC (50/60 Hz)
• Operating Temperature: 14°F to 185°F (-10°C to 85°C)
• Communication: Z-Wave Plus
• Indoor/Outdoor: For indoor use only
• Valve Specifications:
  • Size: 1"
  • Threads: Female NPT
  • Potability: Conforms to NSF/ANSI 61 and 372 standards for potability
• Control Unit Dimensions: 2.75 x 4.0 x 1.25” (6.99 x 10.2 x 3.18 cm)
• Actuator and Valve Dimensions: 2.0 x 4.5 x 3.75” (5.08 x 11.43 x 9.53 cm)
• Maximum Compatible Pipe Size: 1.25" (3.175 cm)
• Power Supply Cable Length: 19.7’ (6 m)
• Plumbing Certifications:
  • ICC-ES-PMG (compliance with NSF 61 and NSF 372)
  • Massachusetts Accepted Plumbing Products Registry

Specifications for Qolsys IQ Water Valve:

• Product Type: Smart Water Valve
• Kit Contents: Qolsys IQ Smart Water Valve, Qolsys IQ Flood-S Sensor
• Communication: Z-Wave Plus V2 700-Series
• Range: Approx. 130 Feet Indoors or 450 Feet Outdoors
• Application: Quarter-Turn Ball Valve Pipes from 1/2" to 1-1/4"
• Maximum Force: 8 N.m
• Ingress Protection: IP66 (Waterproof & Dustproof)
• Power Supply: Plug-in Transformer - AC (110V 60Hz / 220V 50Hz), DC (12V/1A) - Barrel jack
• Weight: 603g (21.2 oz)
• Size: 5.83" x 3.78" x 5.24" (148mm x 96mm x 133mm)
• Operating Temperature: 14°F to 121°F (-10℃ to 49.4℃)

Specifications for DSC PG9985 Flood Sensor:

• Device Type: Wireless Flood Sensor
• Operating Frequency: PowerG 915 MHz
• Wireless Range: ~2,000 Feet Open Air
• Water Detection Probe: Attached w/ 6-Foot Cord
• Batteries: Single CR123A (~8 Year Life)
• Mounting Hardware: Double-Sided Foam Tape (Included)
• Dimensions: 3.1875" x 1.25" x 1.0" (81mm x 34mm x 25mm)
• Operating Temperature: 14°F to 122°F (-10℃ to 50℃)
• Weight: 53g (1.9oz)

Specifications for Qolsys IQ Flood-S Flood Sensor:

• Device Type: Wireless Flood Sensor
• Operating Frequency: 319.5 MHz
• Wireless Range: ~600 Nominal Feet
• Water Detection Probe: Attached w/ 6-Foot Cord
• Signal Outputs: Tamper & Tamper Restore, Alarm & Alarm Restore, Low-Battery
• Supervisory Interval: 70 Minutes
• Batteries: Two (2) Lithium CR2032 Coin Batteries
• Mounting Hardware: Double-Sided Foam Tape (Included)
• Dimensions: 2.5"L x 1"W x 0.5"D (64mm x 25mm x 13mm)
• Operating Temperature: 14°F to 122°F (-10℃ to 50℃)

In addition to the options listed above, there is also the Honeywell/Resideo 5821 that can be used in conjunction with the FP280 flood probe. This sensor will work with any of the Qolsys IQ4 panels that support 345 MHz RF devices. A panel with one or more of these sensors can be used to automate any of the water valves listed in this post.

What are your thoughts on the discontinuation of another FortrezZ Z-Wave device? Have you encountered similar issues with other products? Drop us a comment and let us hear from you. If you have a specific support question, you can send us an email to support@alarmgrid.com. We're here providing support Monday - Friday from 9:00 am until at least 6:00 pm Eastern Time each day. We list holiday hours and closings in our blog.

Freezing and water damage accounted for 29.4% of Homeowner's Insurance losses by cause in 2019*. From 2015 - 2019, the weighted average cost per accident year was $11,000* for freezing and water damage. Only fire and lightning damage was more costly. But flood damage can often be avoided.

At this time of year, with the worst of winter still ahead of us, our thoughts always turn to incidents of flooding which are caused predominantly by freezing temperatures. In many instances, homeowner's insurance companies want proof that there is both freeze and flood protection in a dwelling as a condition of insurance, or in order to provide the best available rate. With just a few added sensors and tweaks, your existing alarm system can help you prevent freezing and flood damage. Below we'll outline some products and strategies that can help.

To properly protect against this type of damage, it is helpful to know when the temperature in a building drops low enough to cause concern. There are many sensors that can assist in this, and in many cases, a sensor may perform double duty. There are motion detectors that also have built-in freeze sensing, as well as smoke, heat, and combination sensors. Here's a list of just a few, and the systems they are compatible with:

With any of the low-temperature sensing devices above, you can be alerted to dangerously low temperatures within a building. Alerts can come in the form of an email, text, or push notification from either Alarm.com or Total Connect 2.0, a call from the monitoring station, or both. With a Z-Wave or WIFI thermostat you can adjust the temperature when the HVAC system is working, or contact an HVAC service technician when it isn't.

Some of the devices listed in the table above combine freeze and flood sensing into a single unit. Of course, avoiding the presence of water in a location where it shouldn't be is optimal, but in some cases, it may not be possible. Flooding isn't always the result of freezing water pipes. With a flood sensor, you can be alerted to these situations and then take action accordingly. Alarm Grid offers a variety of both wired and wireless flood sensors. Some are listed above. Those and others can be found here.

If you can't control what's happening with the temperature in a location, then the next step in avoiding flood damage is controlling the flow of water. If you have a water shut-off valve within the building, then a Z-Wave water valve is just the thing you need to save the day (and a good deal of money). Once you receive a notification that a freeze condition is possible, or that a flood situation is underway, with Alarm.com or Total Connect 2.0 service, you can either set up a scene to automatically shut off the water within the premises, or you can manually log in and do so remotely.

With a combination of freeze and flood sensors, and a Z-Wave Water Valve, you can anticipate potential low-temperature flooding issues, be alerted to non-freeze-related flooding issues, and either automatically or manually turn off the water before damage occurs. Check with your homeowner's insurance agent to see if there are any discounts available on your policy if you add freeze and/or flood protection with an automated water shut-off option. You may be surprised at how quickly this equipment can pay for itself, even if you never have to use it.

*Statistics are taken from the Insurance Information Institute at iii.org.

**Qolsys Panels come in a variety of versions. All IQ Panel 2 Plus and IQ Panel 4 versions support PowerG wireless sensors. Then in addition, there are versions that support 319.5 MHz wireless, including S-Line Sensors. There are also versions that support 345 MHz wireless and 433 MHz wireless. When purchasing a Qolsys panel, or a sensor that will be used with a Qolsys panel, be sure to match the receiver type with the sensor type. Panels that support 319.5 MHz come in a box with a Gold stripe. Panels that support 345 MHz sensors come in a box with a Silver or Gray stripe, and those that support 433 MHz sensors have a Red stripe on the box.

We have a short but exciting announcement today, as new Qolsys IQ Smart Water Valve Kits are now available! There are two (2) kits available, including the Qolsys IQWV908-KIT-PG that uses PowerG communication and the Qolsys IQWV908-KIT-SL that uses 319.5 MHz S-Line communication.

Both of these new kits include two (2) components. The centerpiece is a smart water valve that uses Z-Wave Plus V2 700-Series communication technology. This piece of hardware has an adaptive torque output and can be self-installed on most quarter-turn (1/4 turn) ball valve pipes ranging from one-half inch (1/2") to one and a quarter inch (1-1/4"). Wireless communication is kept super secure using the optional Z-Wave S2 Security Protocol, which is supported by most 500-Series and 700-Series Z-Wave controllers.

Some of the best aspects of the Z-Wave 700-Series Qolsys IQ Smart Water Valve include its ability to be used indoors or outdoors (keep out of direct sunlight), it has an adaptive torque rating of up to eight (8) Nm, and its ingress protection rating of IP66, making it both waterproof and dustproof. The water valve is nice and compact at just 14.8mm x 9.6mm x 13.3mm in size, and it weighs a mere 603g. It can be used reliably in temperatures ranging from 14°F to 121°F. Best of all, it can be self-installed, without the need to hire a plumber.

The other component of the kit is a wireless flood sensor that is ideally used in conjunction with the smart water valve. Depending on the kit you choose, you will get either the DSC 915 MHz PowerG PG9985 Flood Sensor or the Qolsys 319.5 MHz S-Line QS5536-840 Flood Sensor. The PowerG option is good if you have any version of the Qolsys IQ Panel 2 Plus or a DSC PowerSeries NEO Panel with an added PowerG Transceiver. Meanwhile, the S-Line variant is good for the original non-Plus Qolsys IQ Panel 2 or even something like a wireless Interlogix Alarm Panel.

The biggest advantage to using the Z-Wave smart water valve and the wireless flood sensor together is that you can create an automated scene to turn the water off in an emergency situation. The way that this works is that when the flood sensor detects liquid, it will send a signal to the centralized alarm control panel. This faulted zone can then be programmed to trigger an automated smart scene that tells the Z-Wave valve to shut off the water supply. This can stop the flooding and potentially save you thousands of dollars in serious damage. If you've ever experienced the devastation of a major flood, then you will realize this importance.

Do you have any thoughts on this new smart water valve and flood sensor combination package from Qolsys? Share your viewpoint in a comment down below. We would love to hear what you have to say. It's great to see Qolsys taking such initiative in the field of flood damage prevention. Who knows, maybe Resideo and Honeywell Home or 2GIG and Nortek will release their own smart water valve in the near future (pure speculation). From what we can tell Qolsys really put out a winner here, and we're really excited to see it in action. Anyway, that's all the news for now. Keep posted to the Alarm Grid Blog for more updates in the security and smart home automation world coming real soon!