April 2022 Archives

An announcement on the AlarmNet360 page shows that they will send a remote reset command to some LTEM-PA, LTEM-PV, LTEM-PIA, and LTEM-PIV radios. This will occur today, Friday 04/15/22 between 2:00 pm - 3:00 pm ET. This may cause a trouble condition, and queued alarm reports could be sent.

It's unclear why this is being done. After a successful reset occurs, the radio will send an "E339-EXP. Module Power ON / Reset" message to the monitoring station. If the radio was in comm failure prior to the reset and any unsent alarm signals were queued, this reset may cause those alarm messages to be sent. These signals would show up immediately following the E339 signal at the central station. We assume this would also cause the same alarm messages to show up in Total Connect 2.0, and to be sent as notifications.

In addition, depending on how the panel is programmed, this event may cause the panel to display a bF or Check 103 message, and could also cause trouble beeping from the keypad. Disarming the system twice should clear the message and return the system to its normal state.

The Resideo PROINDMV offers a cost-effective alternative to full video monitoring. Up to eight (8) PROINDMV devices can be added to each Total Connect 2.0 account, with no upgrade to full video surveillance required. When activated, the PROINDMV can take a still image or a 10-second clip.

For Alarm Grid customers, any Silver monitoring plan (Self or Full), or higher, can support up to eight (8) of these motion viewers. A Self Bronze plan, can support one (1) PROINDMV. Also, if the panel happens to be set to Local Alarm Mode, then only one (1) motion viewer can be added with clips available locally only. Clips or images captured by the motion viewer can be viewed through the Honeywell Home PROA7PLUS or Resideo PROA7PLUSC panel touchscreen, or through Total Connect 2.0. The PROINDMV is only compatible with the Honeywell Home PROA7PLUS and Resideo PROA7PLUSC panels and is not compatible with the non-plus versions of those panels or with any other panels (as of October 2022).

In order for the PROINDMV to create a clip or image and send it to the panel and TC2, the panel it's used with must have at least a 15-second burglary communication delay enabled, and the panel must stay in alarm long enough for an alarm report to be triggered. At that point, the clip or image will be sent to the panel and to TC2. In the case of the panel being in Local Alarm Mode, the clip will only be sent to the panel. The motion viewer is never recording unless it has detected an alarm. This means that there is no peek-in feature for the motion viewer. A user can't pull up their TC2 account, choose a PROINDMV device and bring up a real-time image. Hopefully, this may change in future firmware updates.

When the system is armed, and a video or image capture occurs during the Entry Delay period, the motion viewer holds any images or clips until after the Entry Delay has expired. If the system is disarmed before the end of Entry Delay, then any clips or images captured during that time are discarded. If it is not disarmed, then those images or clips will be sent once an alarm report is triggered.

Once the PROINDMV has captured a clip or image, it waits either 1.5 minutes (if there is no activity) or 3 minutes (in the event of constant activity) before it will capture another image or clip. A Maximum of ten (10) captures can occur during an armed period (this is assuming Swinger Suppression is set at the Maximum of 6). This is ten (10) captures per PROINDMV, not per account, per armed period. When programming, a PROINDMV can be assigned to any active partition. The response types that are available for the motion viewer are Interior Follower or Interior with Delay. So, the PROINDMV will only be active when its partition is armed Away, or Night (assuming the PROINDMV is enabled for Night Stay Mode).

When the panel camera log gets full, once ten (10) captures have been saved, it will begin to overwrite the oldest captures with new ones. All motion viewer captures are purged from the panel log after 30-days. The panel camera log can not be viewed through AlarmNet360, meaning an alarm dealer can't view any potentially private images. Image or clip captures are sent over WIFI (any time its available) or Cellular (if WIFI is down, or not present). Currently, motion captures cannot be viewed through the Honeywell Home PROWLTOUCH or Resideo PROWLTOUCHC.

Resideo has been investigating an issue with a very small number of communicators. The LTE-CFV, HWF2V-COM, LTE-IV, LTE-L3V, and VISTA-21IPLTE with LTE-21V. In a few cases, starting on March 19, 2022, the Verizon LTE SIM has become locked, causing a comm failure, or secondary path failure.

A device with this issue will show the following symptoms: Locally at the device, the LEDs will flash regularly at a rate of two times per second (see video above). Through AlarmNet360, the affected devices will have checked in normally for the period leading up to March 19, 2022. Then beginning on that date, or on a subsequent date through March 28, 2022, a comm failure will be indicated. Once the comm fail indication appears, it will not clear, so if you've had a comm failure during this time that has restored, then your communication failure is not being caused by this issue.

In addition to the above evidence of an issue, the alarm panel that the communicator is connected to will have a trouble indication displayed. This may come in the form of a Check 103, or a bF on VISTA-20P and similar panels, and also the L3000 panel. For the L3000 panel, the bF will only show on an RF keypad, such as the 5828 or 5828V, the panel itself will show Check or Fault 103. To silence any trouble beeping, enter a disarm command at any panel keypad. These trouble messages can be caused by other things, not just this issue, so if you see one of these error messages and think you may be affected, be sure to contact your alarm dealer for further assistance.

Bear in mind that only the communicators listed above are affected, and that these are all Verizon SIM Cards. If you have an AT&T Communicator, you needn't worry about this issue. Also, for those who have a dual-path communicator with Ethernet connected, you will not necessarily see a Communication Failure message. Instead you will be notified of a Secondary Path Failure. Again, if you are affected by this issue, once the failure occurs, it will not restore. So if you've received a Secondary Path Failure that has since restored, then you experienced a separate issue.

Again, if you feel that you have been affected by this issue, contact your alarm dealer. They can confirm if you are affected and will be able to assist you in receiving a replacement SIM. Alarm Grid customers who are affected have already been contacted and replacement SIMs are on the way. If any further information becomes available, we'll update this post with further details.

Alarm Grid has long steered customers away from Schlage locks due to support issues. In our experience, we have spent time troubleshooting myriad issues between these locks and a number of different Z-Wave controllers. Now, Resideo and Honeywell Home have announced confirmed issues as well.

On April 6, 2022, Resideo and Honeywell Home released a Technical Notification to let users know that recent testing discovered a compatibility issue between Schlage lock models BE468, CAM716, and BE469ZP with the newest Honeywell Home TUXEDO and Resideo TUXEDOC keypads. Also incompatible are the ProSeries panels. The ProSeries lineup includes the Honeywell Home PROA7 and PROA7PLUS and the Resideo PROA7C and PROA7PLUSC. The PLUS versions of these panels offer Z-Wave Plus functionality right out of the box, however the NON-PLUS versions require the addition of the PROWIFIZW in order to offer Z-Wave support.

It should be noted that this alert doesn't include other Resideo or Honeywell Z-Wave controller products such as the Lyric, or the L5100-ZWAVE paired with any of the LynxTouch panels. To the best of our knowledge, these products are still compatible with all of the Schlage locks, though we at Alarm Grid still recommend using a Yale or a Kwikset lock instead of a Schlage, even with one of these controllers. Now that the Honeywell Lyric has been discontinued, and the only LynxTouch panel still available is the L5210, Total Connect 2.0 adherents may be hard pressed to find a panel to support a pre-existing Schlage lock.

It is also important to note that not all Schlage locks that were tested were found to be incompatible. The Schlage J-Series, including the JBE109 and JFE109 locks are compatible and both have been added to the compatibility list for the TUXEDO and ProSeries products. You can read the full MyWebTech Technical Notification #71, which includes compatibility documents for both the TUXEDO keypads, and the ProSeries panels.

Have you tried to use a Schlage Lock with a Honeywell, Honeywell Home, or Resideo Z-Wave controller? Were you successful, or no? Leave a note in the comments below with any thoughts or questions about this announcement. We always look forward to hearing from our readers.