DSC PG9945 Posts

Qolsys recently released a Technical Service Bulletin outlining an issue with the IQ2 and IQ2+ panels and PowerG sensors. In some cases, panels that have just installed either firmware version, or panels running these versions that are rebooted, may lose touch with existing PowerG sensors.

The problem, according to Qolsys, is the encryption key. In some rare cases, either during the reboot after the firmware update, or upon rebooting once the firmware update has been applied, the panel's encryption key can be set back to default. Once this occurs, any PowerG devices in the field that have been programmed into the panel will no longer be able to communicate successfully with the panel.

When this situation occurs, a previously working PowerG device will show status on the panel, and on Alarm.com if monitored, of "Not Networked". It may also show an "!" next to the zone's status on the panel's Home Screen. If this condition is allowed to continue for the full supervisory window of the sensor (24-hours for non-life safety sensors, 4-hours for life safety sensors by default) then each affected sensor will go into supervisory failure at the panel and will show a status of Malfunction when viewed through Alarm.com.

If you see this issue on your Qolsys IQ Panel 2 or IQ Panel 2 plus system, you'll need to delete ALL PowerG sensors from the panel, and then re-learn them from scratch. By doing so, a new encryption key will be created and shared with each PowerG device. Once this has been done, all devices should begin working normally again. PowerG devices should be reprogrammed from the panel, not from Alarm.com. This way, full functionality can be verified once programming is complete. It would be best to be sure the panel does not reboot again until the next firmware update, which will resolve this issue. Only PowerG devices are affected by this anomaly, any legacy RF devices using the 319.5MHz, 345MHz, or 433MHz frequencies, and any Z-Wave devices should not be affected by this issue.

If you haven't updated to 2.5.3 or 2.5.4 yet, it is recommended that you update locally at the panel, rather than through Alarm.com. You can find information on updating via Patch Tag or MicroSD card on our Qolsys IQ Panel 2 Plus Firmware Update Page. Sadly, this won't necessarily prevent this issue from happening, but by being onsite at the time of the update, you'll be able to verify proper PowerG sensor functionality on each of your sensors as soon as the update has completed. According to Qolsys, firmware version 2.5.5 will be released in the near future, though an exact date has not been provided. This version will resolve the root cause of this encryption key issue. Any additional future updates will also include the necessary fix.

If you're interested in no-contract, low-cost monitoring, or if you're an Alarm Grid customer (present or future) with questions, you can reach us at support@alarmgrid.com. We're here to check emails M - F from 9:00 am to 8:00 pm Eastern Time. Thanks for reading, stay safe!

You have likely heard us talking about the benefits of PowerG Sensors at one point or another. Today, we figured we would break down the benefits of these sensors and explain why we like them so much. Let's take an in-depth look at PowerG Sensors and all of their wonderful benefits.

PowerG Sensors were originally designed for the hardwired DSC PowerSeries NEO Systems. By adding a compatible transceiver unit to your PowerSeries NEO, the system will be able to support PowerG Sensors. Johnson Controls, which you may know as the parent company of DSC, took the technology associated with PowerG Sensors, and brought it over to the Qolsys IQ Panel 2 System. This move was not a major surprise, as Johnson Controls also had partial ownership over Qolsys at the time, and Johnson Controls has since bought out Qolsys entirely.

The addition of PowerG support for the IQ2 marked the beginning of the Qolsys IQ Panel 2 Plus, which is how the system is still marketed and sold today. PowerG support is also available for the DSC Iotega, though that panel has largely flopped due to its lack of local end user programming. Today, the Qolsys IQ Panel 2 Plus represents the most popular panel for supporting PowerG. All versions and variants of the IQ Panel 2 Plus support PowerG Sensors, and their exceptional performance makes them the go-to choice for IQ2+ users who want equipment with the best versatility and protection.

Starting with the range, PowerG Sensors can be used from up to 2,000 feet away from the IQ Panel 2 Plus when they are used in an open air environment. By open air environment, we are talking about a perfect setting with a direct line of sight, and no obstacles between the sensor and the alarm panel. Most homes and businesses do not provide the ideal, "open air" environment, as there are usually walls and metal appliances present. When you see us mention that 2,000 feet open air range, take that with a grain of salt, because in practice, the range is likely a bit less. But still, we can undoubtedly say that PowerG offers arguably the best wireless range in the security industry. Even if its nominal range isn't quite as far as its "open air range", it is still a very powerful signal that can help you overcome the range issues that other sensor lineups may experience. It is great for use in detached garages, barns, multi-building complexes, and even just large industrial buildings.

To make matters even better, there is also a PowerG Repeater, the PG9920. This device will effectively double the range of any PowerG Sensor and help you overcome range limitations caused by thick walls and other obstacles or signal disruptions. The repeater works by taking the signal sent out from any PowerG Sensor and sending it out a second time with just as much power and force as when it was first sent from the original sensor. By strategically placing the repeater, it's theoretically possible to double the useful wireless range of these sensors. That would mean that they can be used from up to 4,000 feet away from the IQ2+ in an open air environment. And if your building is particularly large, you may even have repeaters going away from the IQ Panel 2 Plus System in different directions, including up and down in building stories above or below.

But PowerG Sensors offer more than just an impressive wireless range. They are also known for their exceptional security. This is thanks to their military grade 128-bit AES encryption. To put this as simply as possible, the PowerG Sensor and the panel share a unique encryption key at the time of pairing. The sensor must provide this encryption key to the panel whenever it transmits a signal. Additionally, the panel must then provide a return response with the encryption key as verification in order for the command to go through. In the past, we have referred to this two-way communication process as a "digital handshake". Because of this encrypted pairing process, a PowerG Sensor actively knows whether or not it is currently paired with a panel. You may need to factory default a PowerG Sensor before you can pair it with a new system.

PowerG Sensors also take proactive measures against RF jamming. When a wireless sensor communicates with an alarm panel, it does so at a certain wireless radio frequency (RF). When we talk about RF jamming, we are referring to any malicious technique that prevents wireless signals from reaching their intended destination. This is accomplished by blocking the receiver with a stronger signal at the same wireless frequency as the device that is legitimately trying to communicate with it. When this is done on an alarm system, the system doesn't receive the incoming signals from faulted sensors, and no action is taken during a security breach or an unfavorable environmental condition. Early wireless sensors did not take this into account, and this made RF jamming an effective way to defeat an older wireless system.

The way that PowerG Sensors overcome RF jamming techniques is through a process called Frequency Hopping Spread Spectrum (FHSS). This process involves splitting the RF bandwidth into multiple channels. Each independent channel represents a unique radio frequency for wireless communication to occur. The transmitter (the PowerG Sensor) and the receiver (the alarm panel) both agree on a set of channel hopping sequences that will take place. These sequences are encrypted and time-based for them to occur seamlessly. Since the transmitter and the receiver are both synchronized, they can switch between channels very rapidly. A potential intruder would never be able to re-tun an RF jamming device to keep up. In the case of the PowerG Sensors, the frequency hops occur between 912 MHz and 918 MHz. There are 50 different unique frequency channels that are used, and frequency switches occur 64 times per second. More information on FHSS is available here.

One other benefit of PowerG Sensors that we have never discussed previously is their Adaptive Transmission feature that helps them conserve battery life. This is why you will often see a PowerG Sensor with a very long expected battery life, sometimes more than ten (10) years). Adaptive Transmission involves two-way communication between the PowerG Sensor and the alarm panel. The alarm panel will tell the PowerG Sensor how well its signal is being received. The PowerG Sensor can then adapt its outgoing signal so that it reliably reaches the panel, without expending too much energy. The sensor and the panel regularly exchange this information so that the ideal amount of energy is always used in signal transmissions. This saves battery life in the long run.

We have also found that PowerG Sensors are extremely easy to enroll and they offer the reliable and effective performance that you should expect out of your security system. We wholeheartedly recommend them for use on the Qolsys IQ Panel 2 Plus, as well as any other compatible alarm system. It is expected that the upcoming Qolsys IQ Hub will also be able to utilize PowerG Sensors, so look forward to using PowerG Sensors on that panel once it is available.

For now, if you have any questions about PowerG Sensors or the systems that support them, or if you are interested in signing up for new alarm monitoring service, then please reach out to us by emailing support@alarmgrid.com. We'll be available to check your emails from 9am to 8pm ET M-F. We look forward to hearing from you!

With a new year comes reduced pricing on many of our great existing products. We have just dropped the prices on 73 of our existing offerings. You can certainly find something great to upgrade your existing system or use with a new installation. Let's check out these awesome products!

Before we go through and list each and every reduced price product, we figured we'd go through and talk about some of the ones that excite us the most. After all, sorting through a list of 73 products is pretty daunting. Our initial "best-of" list may help you find exactly what you're looking for. These products are great if you have an existing system, or if you are building a new system and want to add some cool accessories.

These products are presented in alphabetical order:

Alarm.com ADC-V723 Outdoor Camera

The ADC-V723 is the current flagship outdoor security camera for use with the Alarm.com platform. This simple, yet powerful camera makes the perfect addition to any home or small business. It can capture video at up to 1080p quality, and it makes use of High Dynamic Range (HDR) to improve image depth and luminosity.

Alarm.com T2000 Smart Z-Wave Thermostat

If you are still looking for a smart Z-Wave thermostat, then the ADC-T2000 is an outstanding entry-level option. It conveniently wires in place of your existing thermostat to give you smart control over your HVAC system. It can pair nicely with both the Alarm.com and Total Connect 2.0 platforms. You just need a compatible Z-Wave hub to get started.

DSC PG9312 Outdoor Door/Window Sensor

The DSC PG9312 is the premier outdoor contact sensor for any user with a PowerG-compatible security system. It offers a maximum magnet spacing gap of 1.75", which gives you more flexibility in choosing a location for the sensor and magnet. Like all PowerG Sensors, it offers a wireless range of up to 2 km away from the panel, as well as 128-bit AES encryption.

DSC PG9914 Motion Sensor

Anyone with a PowerG Security System looking to add a basic indoor motion sensor should turn to the DSC PG9914. This is a simple, yet effective motion sensor that is great for use in nearly any home or business. It offers a modest coverage area of 39 feet, and the sensor provides pet immunity for small animals weighing up to 85 lbs.

Encore FireFighter FF345 Smoke/CO Listening Module

The Encore FireFighter FF345 is perfect if you have existing high-voltage smoke detectors that you want to integrate into a 345 MHz wireless system. The module can detect both the Temporal 3 sound of an activated smoke detector and the Temporal 4 sound of an activated CO detector. And if your high-voltage devices are one-go-all-go, then a single FF345 can takeover your entire network.

Honeywell 5822T Garage Door Tilt Sensor

Also for 345 MHz system users, the Honeywell 5822T allows your system to monitor your garage door to see if it's opened or closed. This wireless sensor works great for security and automation purposes alike. You might even create a special smart scene that activates as soon as the 5822T detects that you garage door has been opened!

Honeywell IPCAM-WIC1 Indoor Camera

The Honeywell IPCAM-WIC1 Indoor Camera is for anyone with an existing Total Connect 2.0 Video Monitoring service plan that they want to expand upon. This is a simple and straightforward camera that captures video at up to 720p quality. It can be easily rested on a desk or table, and no hard-mounting is required.

Qolsys IQ DW MINI-S Door/Window Sensor

The Qolsys IQ DW MINI-S can be used by anyone with a 319.5 MHz wireless system, including the Qolsys IQ Panel 2 Plus w/ Legacy Interlogix & Qolsys Daughtercard. This is a straightforward door and window contact sensor that makes a nice addition to any compatible system. Its small and compact design allows for a tidy installation.

Please see our complete list of reduced price products in the table below, organized by product type:

If you have any questions about these products or any of the other products on our site, including product compatibilities, please reach out to us. You may also contact us if you want to learn more about our monitoring services. The best way to reach us is to email support@alarmgrid.com. Or you may call us at (888) 818-7728. Remember that our support hours run from 9am to 8pm ET M-F. We look forward to helping you find the perfect product for your needs!