Qolsys Releases the Qolsys IQ WIFI Ahead of ISC West

Qolsys released the Qolsys IQ WIFI last week. The IQ WIFI supports dual-band (2.4GHZ and 5GHz) WIFI and can be used as a stand-alone router. It can also be installed in parallel with an existing network. This provides a separate secure WIFI connection for security devices such as cameras.

WIFI is about as common these days as home phones with a traditional copper line (POTS or Plain Old Telephone Service) were from the 1960's through the early 2000's. However, the adoption of WIFI networking has seen some challenges that were not really an issue when using POTS. Namely, the end-user installation and configuration aspect of WIFI networks, as well as issues with getting, and then staying, connected to them. The security industry has embraced WIFI in a big way in recent years, therefore security system users have felt the pain created by these challenges.

For this reason, Qolsys has introduced the Qolsys IQ WIFI. The IQ WIFI is a mesh-capable controller and agent system. Up to eight (8) devices can be supported per network. One IQ WIFI will connect to the modem, router, or switch via a wired ethernet cable. This IQ WIFI will become the controller for the mesh network. Then, up to seven (7) additional IQ WIFI units acting as Agents can be added for a total of eight (8) devices. This allows a user to blanket virtually every nook and cranny of the home or business with a safe and easily configured WIFI connection. If you have a Qolsys IQ Panel 2 or IQ Panel 2 Plus with firmware version 2.6.0 or later, the network can be configured right from the panel's touchscreen. The range between IQ WIFIs is approximately 130 ft. (39.62 m) with a coverage area of approximately 1,500 square feet (139 square meters). Wireless IEEE 802.11 b/g/n 2.4GHz and IEEE 802.11 a/n/ac 5GHz frequencies are supported.

The Qolsys IQ WIFI can be used as a stand-alone router. Each one contains a WAN port, a LAN port, and a barrel connector for power. Each one also has a WPS button. If your ISP provides you with a combination Modem/Router device, connect the WAN port of the IQ WIFI to one of the available ethernet ports on the Modem/Router. From there you can use the IQ WIFI as a wired or WIFI router. For wired devices, connect directly to the LAN port on the IQ WIFI. If you have more than one wired device to connect, connect a multi-port switch to the IQ WIFI LAN port, and then connect your other wired ethernet devices to the switch. As an alternative, connect the WAN port on the IQ WIFI to an existing router or switch, and then using this device as the Controller, build a parallel WIFI mesh network(s) out from there.

Up to seven (7) additional IQ WIFI devices can be added as Agents to create a mesh network that is as strong as you need it to be. This allows you to run a separate WIFI network inside your home or business that is virtually invisible to anyone attempting to hack in from the outside. Another attractive feature of this type of configuration is the ease of replacing the Internet facing hardware. Any time you need to swap out the main modem or router, all you do is swap out the existing hardware, then connect the Qolsys IQ WIFI acting as the Controller to the new piece of equipment. All of the WIFI devices that have been configured to connect through the IQ WIFI will keep their current configuration. There is no need to go around to each WIFI device and enter new credentials. This is particularly welcome when you have WIFI equipment, such as fixed-mount cameras, that may be installed in multiple and difficult to reach locations.

In many cases, security devices can only use the 2.4GHz WIFI band. When the SSID for both 2.4GHz and 5GHz are the same, this can cause issues for those devices that don't support both frequencies. We've seen this in many instances with the Honeywell Lyric. By allowing the user to separate the two bands, achieved by changing the SSID on one or both of them, you can make sure that any device that needs to use only one band or the other can find and then remain connected to the proper WIFI network. It may seem counter-intuitive to think that a Qolsys product could help to stabilize the WIFI connection for a Resideo or Honeywell alarm system, but it is absolutely possible.

When Qolsys first talked about this device, they called it the Qolsys IQ Router. Since then, they have updated the name to Qolsys IQ WIFI and they plan to release a separate device called the Qolsys IQ Router2, or possibly the IQ WIFI6 later in the year. This will be a more robust device supporting both WIFI and potentially another technology such as Z-Wave, Zigbee, or maybe even PowerG. We look forward to hearing about many more new products to come! What do you think of the Qolsys IQ WIFI? Leave a comment below. We'd love to hear from you.