AlarmNet360 Posts

I was able to speak with an industry insider familiar with the events at Resideo's data center on Sunday night into Monday evening. This person related to me that there was an HVAC failure at the primary data center. It was initially thought to be an easy fix, but that turned out to be false.

Things started to go wrong in Resideo's primary data center on Sunday night at around 7:00 PM Eastern Time. An HVAC failure allowed the temperature in the data center to climb to a dangerous level for the servers located there. The normal temperature is around 70℉ (21℃) but on Sunday it rose into the neighborhood of 130℉ (54.4℃). The servers are set to failsafe, so rather than continue running, and risk catastrophic damage, they began to shut down.

An automated system is in place which notifies engineering and other stakeholders when a serious event like this occurs. An HVAC technician responded. Initially, the technician believed this would be a quick and easy fix, so the decision was made not to switch to the secondary data center, which is located in the Chicago area. The switch takes a bit of time, somewhere around 20 minutes, and the thought was that it wouldn't be worthwhile at that point to make the switch.

However, the HVAC tech discovered that in order to implement a fix, he or she was going to require a part, which they didn't have and couldn't get at that time. So, at around 1:00 AM Eastern Time, the decision was made to switch things over to the secondary data center. By about 1:30 AM Eastern Time, the backup data center was in control.

At around daylight Monday morning the HVAC system in the primary data center had been fixed. Once it was fixed, there was a period of time where the temperature was coming down to an acceptable level. By approximately 11:00 AM Eastern Time, Resideo was ready to switch back to the primary data center. At this point, alarm signaling was back up and had been for some time. By around 2:00 PM AlarmNet360 was back up, and by about 6:00 PM Total Connect 2.0 was back online, though customers and our own testing show that it was somewhat sluggish at first.

This outage affected three (3) things. The most serious was alarm signaling. During the early hours of the outage, customer's systems were unable to send signals to the monitoring station, or to send notifications to the customers themselves. Total Connect 2.0, the customer-facing app and website for end-user remote control was also down. Lastly, AlarmNet360, the alarm dealer facing service used to create or cancel accounts and remotely troubleshoot issues was also affected. When things went wrong, the initial focus was on getting alarm signaling backup as quickly as possible. This was the focus when they initially switched to the Chicago area data center.

This is a fully redundant system, and it is tested regularly. According to my source, there were hourly notifications being sent to alarm dealers, but the database of email addresses for these notifications seems to be outdated. This is something they will address going forward. A root cause analysis will be completed in the coming days, and any processes or procedures that need to be updated will be dealt with at that time. The site at status.resideo.com doesn't have a section showing either AlarmNet360 or Total Connect 2.0 status. Hopefully, this is something that will change in the very near future as well. Finally, those dealers who did receive notification noted that the emails weren't flagged as containing particularly important information. This is also something that will be addressed in the future.

Today, February 22, 2022 is the official date for the AT&T 3G Sunset. As we've mentioned before, there isn't a big switch that gets turned off and then, "Poof!" no more 3G. If you still have an AT&T 3G communicator, it may continue to work for a while, but there is no way to know how long.

If you're just becoming aware of the AT&T 3G Sunset because you have a security panel that you haven't been paying much attention to for a while, then you probably are seeing some type of error, and possibly hearing some annoying beeping. Some of the more common error messages are shown further down in this post. The thing to keep in mind is that your alarm panel wants to be sure that you know there's a problem. So, if you just press the touchscreen, or press any button on the keypad, that should stop the beeping, at least temporarily.

If you know the arming/disarming code for the system, enter it if prompted on a touchscreen panel, or if you're on a VISTA panel, just enter your 4-digit code and then press the OFF or 1 Key. This will acknowledge the trouble condition and stop the beeping on a more permanent basis, though in some cases, it may come back after a period of time. If you don't know a valid code for the system, then you will likely need to shut down your system by unplugging the transformer and the battery. If you're interested in putting your system into service keep reading to see how Alarm Grid is helping out in this situation.

If you find yourself in the unenviable position of needing to replace an AT&T 3G communicator, but you haven't done so yet, don't panic. The AT&T 3G network is vast and complex. It's not something that you can simply turn off. The process of sunsetting 3G equipment will take a bit of time. So, if after today your 3G communicator still works, you're one of the lucky ones. You've been given a slight reprieve. However, there is no way for us to know how long that reprieve will last, so decide what you're going to do, and do it now.

One ongoing problem that we've seen recently is supply chain issues. Maybe you've been trying to upgrade for the past six (6) months, but the communicator or system you need hasn't been available. Communicator manufacturers have been rolling out LTE Cat-M1 communicators in the absence of available components for standard LTE.

LTE Cat-M1 is the cellular network that was created for Internet-of-Things (IoT) use. It has lower power consumption, better range, and the modems used for it have a smaller form factor. The trade-off is lower bandwidth. However, the amount of data being transmitted by alarm communicators is very low compared to voice and data used for a traditional phone, so the difference in bandwidth isn't noticeable. Happily, the components to make LTE Cat-M1 communicators appears to be readily available, so those communicators have been coming into stock in the past months and continue to become available.

Some of the available AlarmNet LTE Cat-M1 communicators are listed below. These communicators are all compatible with the VISTA panels. The LTEM-PA and LTEM-PV are also compatible with the DSC PC1616, DSC PC1832, and DSC PC1864 and the Interlogix NX Series panels. For the Interlogix NX Series, the PRODCM is also required:

• LTEM-PA - Dual-path IP and AT&T LTE Cat-M1 communicator with the ability to add a traditional LTE communicator if needed. First communicator to allow non-Honeywell panels to use Total Connect 2.0.
• LTEM-PV - Dual-path IP and Verizon LTE Cat-M1 communicator with the ability to add a traditional LTE communicator if needed. Along with the LTEM-PA can allow non-Honeywell panels to use Total Connect 2.0.
• LTEM-XA - AT&T LTE Cat-M1 Communicator for VISTA Panels.
• LTEMXA-TC2 - AT&T LTE Cat-M1 Communicator for VISTA Panels. Includes upgrade chips for VISTA-15P and VISTA-20P panels, allowing them to support Total Connect 2.0.
• LTEM-XV - Verizon LTE Cat-M1 Communicator for VISTA Panels.
LTEMXV-TC2 - Verizon LTE Cat-M1 Communicator for VISTA Panels. Includes upgrade chips for VISTA-15P and VISTA-20P panels, allowing them to support Total Connect 2.0.
• LTEM-IA -COMING SOON - AT&T LTE Cat-M1 Communicator with RJ45 Port for Ethernet. Currently in Beta.
• LTEM-PIA - AT&T LTE Cat-M1 Communicator with RJ45 Ethernet port. Listed for UL-985 Household Fire.
• LTEM-PIV - Verizon LTE Cat-M1 Communicator with RJ45 Ethernet port. Listed for UL-985 Household Fire.

Some of the available Alarm.com LTE Cat-M1 communicators are listed below. Compatibility is listed with each communicator:

• Alarm.com ADC-SEM210-PS-AT-M - COMING SOON - Dual-path AT&T LTE Cat-M1 and ethernet capable communicator for use with legacy DSC Power Series panels (PC1616, PC1832, PC1864).
• Alarm.com ADC-SEM210-PS-VZ-M - COMING SOON. - Dual-path Verizon LTE Cat-M1 and ethernet capable communicator for use with legacy DSC Power Series panels (PC1616, PC1832, PC1864).
• Alarm.com ADC-SEM300-VT-AT-M - COMING SOON. - Dual-path AT&T LTE Cat-M1 and ethernet capable communicator for use with Honeywell VISTA (non-polling loop) panels (VISTA-10P, VISTA-15P, VISTA-20P, VISTA-21iP manufactured in 2005 or later).
• Alarm.com ADC-SEM300-VT-VZ-M - Dual-path Verizon LTE Cat-M1 and ethernet capable communicator for use with Honeywell VISTA (non-polling loop) panels (VISTA-10P, VISTA-15P, VISTA-20P, VISTA-21iP manufactured in 2005 or later).

Panel Cellular Communicator Trouble Condition Messages

If you are affected immediately by the AT&T 3G shutdown, you may see one of these error messages on your system:

• Check 103 ####: - You may see this on a non-polling VISTA panel, such as the VISTA-20P, but only if you have an Alpha Keypad like a 6160. The #### will be a 4-digit number. It may be 4005, which indicates that the communicator has lost connection with AlarmNet. The exact 4-digit code will depend on whether there are any other trouble conditions existing on the communicator at the time the message is displayed.
  *If you have a VISTA panel, choose from any of the communicators listed above for VISTA panels. The VISTA-21IPLTE can use the LTE-21V. The only way to update an original VISTA-21iP is to add an external communicator and disable the internal one. The prior link is an FAQ on how to do just that. The same rule about possibly downgrading to an IP only plan mentioned under the bF message applies here too.
• bF, or it may look like 6F: - This is supposed to be a bF, which stands for Backup Failure, as in backup communicator. This message means the same thing as Check 103, but will be displayed on a non-alpha keypad like a 6150. If this is the only type of keypad you have, then this is all the information the panel and the communicator can give you. If you get this message after 02/22/22 and your AT&T 3G Communicator has been fine until then, you're not one of the lucky ones. You should look to upgrade your communicator ASAP. *Or, if you have a dual-path communicator and an IP connection is available near it, you could downgrade to an IP only plan for now, and upgrade to LTE at a later time. Just bear in mind, if you go IP only, when the internet is out, your panel's ability to communicate is out. This is usually the case during power outages. The above rule about upgrading the communicator under the Check 103 message also applies here.
• Fault 103: - This may also show as a Check 103, then display as a Fault 103 after you silence the panel. This is what you see on the Honeywell L3000 panels when there is a problem with the communicator. Losing connection due to the 3G Sunset would cause this error code. There is not a good IP only option for the L3000 currently available. You can use a 7847-I, but it is a messy installation. You can also use the 7847I-L, if you can find one, they are discontinued.
  • Honeywell LTE-L3V - Verizon LTE Communicator for the Honeywell L3000 panel.
  • Honeywell LTE-L3A - AT&T LTE Communicator for the Honeywell L3000 panel.
• 103 Comm. Trouble: - The Lynx Touch Panels will display something along these lines. The icon and message may differ slightly, but the gist is the same. This is what you'll see on these panels if you're affected by the AT&T 3G shut down.
  • Honeywell LTE-L57A: - AT&T LTE Communicator for Lynx Touch panels. Important! There may be panel firmware revision restrictions with your panel and either of these communicators. Read the product description very carefully to be sure your panel is on the correct version for the communicator you choose. If you need to update the panel, you can do so with the Honeywell LYNXTOUCH-MSD Firmware Update Tool. It is compatible with the L5200, L5210, and L7000.
  • Honeywell LTE-L57V: - Verizon LTE communicator for the Lynx Touch panels. See the Important note above about panel firmware version limitations.
• ⚠ 950 Comm. Trouble: This is the message displayed on a Lyric Controller if it has a cellular communication path, and it loses contact with AlarmNet on that path. This is what you will see if the AT&T 3G shutdown has caused your communicator to go down. There may be other messages in the status bar at the top of the screen as well, having to do with Comm Failure and potentially other conditions, depending on what's happening with your panel at the time.
  • Honeywell LYRICLTE-A - AT&T LTE Communicator for Lyric. Firmware Revision v01.03.06548.482 or higher required!
  • Honeywell LYRICLTE-V - Verizon LTE Communicator for Lyric. Firmware Revision 1.09 (aka MR9) or higher required!
    
    
• Check 8##, ####: - You may see this message on a VISTA-128 or VISTA-250 panel. Devices connected to the keypad bus can be supervised for a connection to the panel, and for a tamper condition where applicable. The AT&T 3G Communicator can also be supervised for communicator troubles, such as a loss of connection to AlarmNet. If supervision is enabled (and it is not enabled by default) then when the 3G Sunset affects the communicator, the panel will display a Check or Trouble (based on programming) 8 + the 2-digit number of the address. So, if the communicator is assigned to address 03, and supervision is enabled, it will display as a Check or Trouble on Zone 803 plus the 4-digit communicator status code associated with the condition when you have the proper keypad to display it. If the only problem is a loss of network connection, then the 4-digit code should be 4005. Supervision is enabled by enabling the associated 800-zone with a trouble zone type, such as 05, Trouble by Day/Alarm by Night.
• 2GIG GC2 and GC2e Displays Trouble Icon and beeps 6 Times per minute until the trouble condition is acknowledged: This is the behavior of the 2GIG GC2e and presumable the 2GIG GC2 as well. The Security Screen will show a Yellow button with an exclamation mark and a number. When you press the button, it will take you to the Trouble Display screen where you can scroll through the trouble conditions, and you may click on the communicator trouble then press OK. This will stop any beeping, but the display will continue to show trouble until the condition is cleared. In the case of the AT&T 3G Sunset, this means upgrading the communicator.
  
  
  
  • 2GIG LTEA-A-GC2: - Alarm.com compatible AT&T LTE Communicator for 2GIG GC2 and 2GIG GC2e. Important! Be sure to check for any panel firmware version requirements associated with either of these LTE communicators for the 2GIG GC2 and GC2e panels.
  • 2GIG LTEV1-A-GC2: - Alarm.com compatible Verizon LTE Communicator for 2GIG GC2 and 2GIG GC2e.
2GIG GC3 and GC3e Message LED is lit and the panel chimes at ten-second intervals until the condition is acknowledged: The behavior for the cellular communicator losing connection to the AT&T 3G network on a 2GIG GC3 or GC3e depends somewhat on panel programming. In Q30, you set the amount of time that is allowed to elapse with no communication to the server before a trouble condition is indicated. The default is 30 minutes. A 0 in this field disables the supervision feature. The maximum entry is 255 minutes. Q31 also determines whether the radio network failure causes a trouble condition on the panel. This is enabled by default, but if disabled, you will have no visible indication if you are affected by the AT&T 3G sunset. Q32 is radio network failure reports. This is enabled by default and determines whether the panel reports the radio failure to the monitoring station (assuming it is able to do so with the radio down, the panel would need to be utilizing the WIFI communication path for this to be possible.)
• 2GIG LTEA-A-GC3: AT&T LTE Communicator for the 2GIG GC3 and GC3e panels. The panel must have Firmware Version 3.2.3 or higher to support this communicator.
• 2GIG LTEV1-A-GC3: Verizon LTE Communicator for the 2GIG GC3 and GC3e panels. The GC3 or GC3e must have Firmware Version 3.1.3 or higher to support this communicator.

Alarm Grid Is Here To Help!

If you're a current Alarm Grid customer and you have purchased an LTE communicator, but haven't switched over to it yet, please send an email to support@alarmgrid.com. In the subject line, be sure to put "I Need an LTE Upgrade". We'll reach out with further instructions and either a link to schedule your upgrade, or information as to what we need to begin your upgrade. Lyric and Lynx Touch users may be able to get upgraded with no appointment, where a VISTA user may require an appointment as those communicator swaps are a little more intricate.

If you purchase an LTE communicator or an upgrade kit from Alarm Grid, we will credit your monitoring account in the amount of the communicator or upgrade kit. If you purchase more than $150 in product, we'll also offer you free ground shipping, so if you've been thinking of adding a doorbell camera, or other products to your system, now may be a good time. The cost of products not associated with the communicator or system and communicator upgrade will not count toward free monitoring though.

If you have the ability to switch to an ethernet or WIFI connection only, you can choose to do that and your monthly monitoring fee will go down. You can purchase an IP or WIFI communicator strictly for that purpose. You may have that option with your existing panel and you just aren't using it, or maybe you were using dual-path monitoring, but now the cellular portion of your 3G communicator has stopped working. Whatever the case, if your communicator or panel supports the option for an IP-only connection, we will be glad to downgrade your service plan permanently, or until you can get the LTE upgrade. But be aware, Alarm.com customers do not have an option for IP-only monitoring.

If you're not a current Alarm Grid customer, never fear, you can get exactly the same deal as existing customers. If you purchase an LTE communicator from us or a kit with a panel and LTE communicator and you then sign up for monitoring with us, we'll give you credit toward free monitoring in the amount of the purchase for the communicator or communicator and panel. Once again, purchases over $150 will have free ground shipping, but any sensors or other devices that you purchase will not count toward free monitoring.

If you have any questions, feel free to reach out to us at support@alarmgrid.com. Our support hours are Monday - Friday from 9:00 am - 8:00 pm Eastern. We will help in any way that we can to get you through this transition. Your safety and peace of mind is our top priority.

A recent blog post about the looming AT&T 3G Sunset contained an error. We mentioned in that blog that the ingenious Resideo Cellbounce, a 3G to LTE converter, does not support Total Connect 2.0. That is incorrect. As long as the original 3G device supports TC2, the Cellbounce also supports it.

This misinformation has been updated in the original post, but for those who may have already read it, we wanted to also briefly touch on it here. In brief, the Resideo Cellbounce is a plug-and-play device. It plugs into a standard 110 Volt AC outlet and should be mounted within 25' (7.6m) of the working AT&T 3G Communicator. The Cellbounce connects to the 3G communicator, and to an AT&T LTE network. Once those connections have been made, it acts as a bridge, receiving the 3G information and transmitting it through the LTE network.

AT&T has committed to supporting the Resideo Cellbounce unit until at least the end of April, 2025. It is possible that support may go beyond that date, but the contractual obligation ends on May 1. Since the Cellbounce is plug-and-play, anyone can install it. An Installation Professional is not required. Though, it is important to note that the Cellbounce should not be powered on until after the information has been added to the customer account by the alarm dealer.

The Cellbounce will arrive in a box with a Serial Number and an IMEI number printed on it. This information must be provided to the alarm dealer so that they can attach the unit to the proper customer account. This step must be performed BEFORE the Cellbounce is powered on. Once power is applied, within a few minutes the Cellbounce will connect to the existing communicator and to the LTE network. LEDs on the unit will signal when these connections take place. From there it's just a matter of testing to be sure signals are going through successfully. Just be sure to put your system on test with the monitoring station prior to beginning this process.

The Resideo Cellbounce is only compatible with AlarmNet AT&T 3G communicators. The existing communicator must be registered and working. This means it can't be in a comm failure condition. Adding a Cellbounce to a communicator that is in comm failure will not correct that issue.

We are in the midst of a strange confluence of events. The COVID-19 pandemic has wreaked havoc on both manufacturing and supply chains, with both sub-assembly parts and product delivery being affected. Add to that the AT&T 3G/4G GSM sunset and you'll have a good picture of where we are today.

We've known about the AT&T sunset for some time. We've written about it in this blog on numerous occasions. Alarm Grid implemented an email campaign to proactively remind our customers who needed an upgrade not to wait until the last minute. But there will always be people who want to wring every last bit of usefulness out of their current product, before upgrading to a new one. I don't blame them, really. But the strange confluence of events I mentioned earlier may find those folks scrambling to upgrade at the last minute.

Security communicator manufacturers, including Resideo, and Alarm.com are doing everything they can to bridge the gap between supply and demand. They are introducing new product lines, with alternatives to standard LTE such as those that use the LTE Cat-M1 network. Resideo has introduced the LTEM-PA and LTEM-PV and they are beta testing the LTEM-IA for future release. The benefit of these products is that they provide nearly the same experience as the previously released LTE products, but either due to happenstance or good planning, components for these products are readily available, so while other LTE products are on backorder, these units are plentiful.

Alarm.com also has a series of LTE Cat-M1 System Enhancement Modules (SEM), including the Alarm.com ADC-SEM300-VT-AT-M (coming soon) and the ADC-SEM300-VT-VZ-M which is available for purchase now. Both of these SEMs are compatible with the Honeywell VISTA product line (with the exception of the VISTA-128 and VISTA-250 panels). They allow compatible VISTA panels to communicate using Alarm.com, and to work with the Alarm.com remote control features. These are dual-path communicators that also have a Z-Wave plus controller built in. Alarm.com will soon have the ADC-SEM210-PS-AT-M and the ADC-SEM210-PS-VZ-M. These dual-path communicators with Z-Wave Plus controllers will support the older DSC Power Series panels (PC1616, PC1832, PC1864 all version 4.20+).

Perhaps the most intriguing "Bridge the Gap" product available currently is the Resideo Cellbounce. This product has some limitations, it only works with AT&T 3G communicators, it only works in states within the contiguous US (sorry Alaska, Hawaii, and Puerto Rico), and it can only be installed with a communicator that is currently still registered and active on the AT&T 3G network. If the communicator is in comm failure, this condition has to be resolved before a Cellbounce can be added. There are some other limitations too, such as it can't support Total Connect 2.0, (CORRECTION: It CAN support TC2 as long as the original AT&T 3G communicator supports it.) But be sure to read the full product description linked above before deciding to purchase.

The Cellbounce is a plug-and-play device. Anyone can install it, so no installer visit is required. It can work with any Honeywell or Resideo AT&T 3G communicator. The Cellbounce is installed within range, which is 25' (7.6m), of an existing, registered AT&T 3G communicator. The Alarm Dealer will need the Serial Number and IMEI Number from the Callbounce unit. These can be found on the box the device comes in.

Important Note: Provisioning must take place on the AlarmNet360 server BEFORE the Cellbounce unit is powered on.

Once the Cellbounce has been provisioned, it should be powered up using an unswitched outlet, not a power strip. From there, the Cellbounce does all the heavy lifting. On one hand, it reaches out and finds an LTE signal, on the other, it reaches out to the existing 3G communicator and locks on to it. Once both of these connections have been made, any time the 3G communicator sends a signal, the Cellbounce captures it and transfers it to the LTE network. AT&T has promised that the Cellbounce units will continue to function until at least Q1 2025. This should give any Cellbounce users plenty of additional time to upgrade. There are a limited number of Cellbounce units available, so if this sounds like an attractive option for you, order yours today. Don't get left behind!

Sunset Graphic courtesy of AlarmNet360:

In 2021 we said goodbye to some products (here's lookin' at you, Qolsys IQ Panel 2) and hello to others. We'll take a look back on 2021 and highlight some of the changes we've seen in the industry. From new Alarm.com cameras to redesigned alarm panels, here's a look back at 2021, as it was.

January, 2021: The new year saw the release of the Alarm.com ADC-V515 Camera. This budget-friendly camera offers 1080p recording with High Dynamic Range (HDR) and a 110° field of view. The IR Night Vision feature has a range of ~15 feet. This is an indoor camera that connects to 2.4 GHz WIFI networks, and it supports the full suite of Video Analytics features.

We also said goodbye to the Honeywell 5877 Garage Door Relay. This product works in conjunction with the Honeywell Wireless Alarm Panels, with the exception of the ProSeries panels, to allow automation and remote control of a garage door. We said "Goodbye" to it in January, but we should have said "See you later" because in October we said "Hello" again! Alarm Grid was able to obtain a number of 5877s, and we'll continue to offer it until stock exhaustion. Since Honeywell has decided they will no longer produce it, at that point, it will be "Goodbye forever".

February, 2021: In February, Alarm.com announced the discontinuation of the ADC-SVR122. Although they still offer the ADC-CSVR126 this is a commercial version of the SVR122, and may not be suitable for the average residential user. In lieu of using a Stream Video Recorder, Alarm.com offers the Onboard Recording feature as an alternative to a traditional residential DVR. Click here for a list of cameras that support this feature.

March, 2021: In March, Resideo discontinued the IPCAM-WOC1, leaving their Total Connect 2.0 product with no outdoor camera option. Later in the year, they released a replacement, so TC2 users will have an outdoor camera choice, but until recently the IPCAM-WOC2 was on backorder due to supply chain issues. It is now available for purchase again and ready to ship!

Honeywell Home added the PROA7 panel to the ProSeries Lineup that they released late in 2020. In reality, the Honeywell Home PROA7 and PROA7PLUS are basically the same products as the Resideo PROA7C and PROA7PLUSC, but with different branding on the front of the panel. The PROA7 and PROA7C are "Lite" versions of the PROA7PLUS and PROA7PLUSC. The non-plus versions have no front-facing camera for disarm photos and don't support Bluetooth. They will support WIFI and Z-Wave, but don't come with the Honeywell Home PROWIFIZW built-in. For these panels, if you want WIFI, but no Z-Wave, you can choose to add the Honeywell Home PROWIFI module instead. All of the ProSeries panels support the addition of either the PROLTE-A or PROLTE-V LTE Cellular Communicators and the Honeywell Home PROTAKEOVER legacy wireless takeover module.

April, 2021: In April, 2GIG released the 2GIG Edge. They teased their newest panel for quite some time, via its own countdown webpage. After a couple of release date changes, on April 1, 2021 it became available. The Edge was an instant sensation, with a number of industry awards in addition to an honorable mention. The Edge has a strong feature set, and comes in both an Edge AT&T LTE and an Edge Verizon LTE version. Dual-path ready, with 100 Zones, 100 User Codes, Z-Wave Plus V2, and Facial Recognition Arming and Disarming, the Edge is an excellent option for a new and modern security system.

May, 2021: With the release of the 2GIG Edge, the GC3e was discontinued upon stock exhaustion. Alarm Grid originally retained some stock of the product, and offered it at an attractive price for a limited time, until our stock was exhausted. The 2GIG GC3e has now gone the way of the dinosaurs. Also in May, Alarm.com announced new support for Ecobee Smart Thermostats via server-to-server integration.

June, 2021: Alarm.com announced the release of some new System Enhancement Modules (SEM) to support the Honeywell VISTA-10P, VISTA-15P, VISTA-20P, and VISTA-21iP panels. These are Dual-Path communicators with lower power consumption than their predecessors, with the ability to be used without an external power supply. The ADC-SEM300-VT-AT uses AT&T LTE while the ADC-SEM300-VT-VZ uses Verizon LTE.

In June, Qolsys also introduced two (2) Smart Water Valve Kits. The Qolsys IQWV908-KIT-PG includes the DSC PG9985 PowerG Flood Sensor coupled with Qolsys' Z-Wave Plus 700-Series Smart Water Valve. With these two products, you can have your system sense a water leak in the early stages, and through an Alarm.com Automation Rule, automatically turn off the water until the issue can be resolved. The PowerG sensor provides exceptional wireless transmitting range. It can work up to 4,000 feet (1219m) away from a Qolsys IQ Panel 4 without a repeater being required, and will work with all variations of that panel.

Qolsys also introduced the Qolsys IQWV908-KIT-SL. This kit includes the same great Z-Wave water valve, but with a Qolsys IQ Flood-S 319.5 MHz flood sensor for use with the Qolsys IQ Panel 2 & 2 Plus 319.5 MHz version or Qolsys IQ Panel 4 AT&T 319.5 Mhz version or Qolsys IQ Panel 4 Verizon 319.5 MHz version, or even one of the Interlogix panels that support the 319.5 MHz frequency. This flood sensor will only work with the 319.5 MHz version panels, so be certain which panel you have when ordering.

Resideo and Honeywell Home introduced a firmware update for the Honeywell Home PROA7 and PROA7PLUS, and the Resideo PROA7C and PROA7PLUSC that enabled programming through the panel touchscreen (or via a remote touchscreen keypad, the PROWLTOUCH or PROWLTOUCHC). Many users had been waiting not-so-patiently for this update, particularly DIY users who prefer to handle their own panel programming. Prior to this update, referred to as MR3, only an alarm dealer could program the ProSeries panels and only remotely via AlarmNet360 or via the AlarmNet360 Mobile App.

And finally, in June we discovered that the 2GIG Edge had a limitation with regard to using Image Sensors. Namely, that at the time of the panel's release, the 2GIG IMAGE3 only behaved like any other motion sensor when paired with the panel. It did not provide any alarm images, or the ability to peek in. Fortunately, in August 2GIG released Firmware Version 3.1.0.011, which solved this issue.

July, 2021: Honeywell Home announced in July the addition of the PROSIXRPTR Encrypted Wireless Repeater. Up to two (2) repeaters can be used with each ProSeries system and each repeater increases the range for PROSIX and SiX Series sensors by about 200 feet (60m).

Qolsys released the Qolsys IQ WIFI just ahead of ISC West. This product allows the alarm dealer to control all, or a portion of the customer's network to provide for easier alarm system integration to WIFI, as well as easier remote troubleshooting. Up to eight (8) IQ WIFI devices can be used per network with one (1) behaving as the controller, while up to seven (7) behave as agents. Locally, the IQ WIFIs can be configured using the touchscreen on a Qolsys panel (IQ Panel 2 must be version 2.6.0 or higher).

Z-Wave continued to evolve in 2021, and we began to move up from Z-Wave Plus to Z-Wave Plus V2 products. Z-Wave Plus uses the 500-Series Chipset, while Z-Wave Plus V2 uses the 700-Series Chipset. The 2GIG Edge uses a Z-Wave Plus V2 Chip as does the Qolsys IQ Panel 4. We've received no word on when, or if the ProSeries panels from Resideo and Honeywell Home will move up from the 500-Series Chipset to the 700-Series. You can read about the differences between the versions of Z-Wave here.

August, 2021: August was a sad month for us at Alarm Grid. We lost our beloved, and prolific writer Michael Goris suddenly and unexpectedly. Not only did Michael write about everything having to do with alarms, he was also featured in many of our videos, particularly once COVID-19 hit hard and we couldn't all always be in the office together. We miss you Michael.

Resideo and Honeywell Home announced compatibility issues between certain of their 6160RF keypads and the 5800WAVE or 5800RL products. The issue had to do with the 6160RF not sending correct status information from the panel to the 5800WAVE or 5800RL. This issue affected keypads manufactured between May 26, 2020 and February 18, 2021. You can read the full post about it here to determine if you have a keypad that may be affected.

September, 2021: Resideo and Honeywell Home announced in September that the Weather feature on the TUXWIFIW and TUXWIFIS would no longer be available. This, after they had issues for months with the information for this screen not updating properly. In the final week of December, we received good news that this issue has been resolved and that the weather for these products is now operating as it should!

On another positive note, the Resideo and Honeywell home ProSeries panels won the CEPro Best Product Award. Specifically, they won the award for Best Integrated Security System/Module/Device/Surveillance Camera System. You can read the full announcement here.

October, 2021: In October, Alarm.com announced the release of the Alarm.com ADC-V724 their first outdoor camera that supports 2-way audio. In addition, it supports the full suite of video analytics, and onboard recording, it also supports dual-band WIFI and IR Night Vision with a range of up to 49 feet (15m). This camera came out just in time for homeowners to really mess with the trick-or-treaters in their neighborhood using the 2-way audio feature!

In October we also got a sneak-peek at the new Resideo IPCAM-WOC2, which replaced the IPCAM-WOC1. Briefly, we had a new supply of outdoor cameras that were compatible with Total Connect 2.0, however we sold out pretty quickly. Supply chain issues had this camera back on the unavailable list but as of December, 2021 it is back in stock and ready to ship.

Resideo and Honeywell Home announced in October that with Firmware Version 03.592.107.0 for the ProSeries panels the Honeywell Home PROTAKEOVER Legacy RF Receiver module will now support wireless life-safety devices. Although you can now program any supported legacy RF device for life-safety, the Honeywell 5800 Series wireless devices have actually been tested to ETL standards for Residential Fire. This update also brought other exciting features and fixes. You can read all about them here.

November, 2021: This is the sad month we knew would come when the Qolsys IQ Panel 4 was announced earlier in the year. In November, Qolsys announced the End of Life for the Qolsys IQ Panel 2 Plus 319.5 MHz panel versions. Users can now purchase the IQ Panel 4 in the 319.5 MHz flavor. As supply chain issues abate, the IQ Panel 4 345 MHz option, and the 433 MHz option will become available, and as they do, their corresponding IQ Panel 2 Plus versions will also be discontinued.

We also discovered in November that the IQ Panel 4 will only support the newest version of the Qolsys IQ Remote. An easy way to tell if you have the newest version of the IQ Remote is to look for the front-facing camera. If the camera is in the top center, you have a newer keypad. If the camera is in the upper-right corner, then you have an older IQ Remote that won't work with the IQ Panel 4. Read our full notice on this information.

December, 2021: In December we received critical notices from both Alarm.com/Qolsys and AlarmNet that a couple of their products will require a firmware update prior to the 2022 AT&T 3G Sunset. For AlarmNet, any Lyric Controller with a LYRICLTE-A AT&T LTE Communicator installed must be updated prior to 02/22/22. Read the full notice from AlarmNet and Resideo. The Verizon communicators are not affected by this notice.

On the Alarm.com side, the Qolsys IQ Panel 2 and IQ Panel 2 Plus panels with an AT&T LTE Cellular Communicator also require an update prior to 02/22/22. In some cases, the panel firmware needs to be updated first, before the cellular firmware update can be implemented. Read the full notice on the Alarm.com update requirement. Again, the Verizon versions of these products are not affected.

So that's it, 2021 in a nutshell. As is usually the case, it has been a year full of ups and downs. We have seen a lot of positive change in our industry. The era of COVID-19 has exposed some opportunities in the physical safety world that may not otherwise have been considered without the pandemic having occurred. Touchless doorbells, and biometric system control are just a couple of things that have come to fruition during this time. I don't know about you, but I can't wait to see what 2022 has in store for us.

Users of the Lyric Alarm System with an LYRICLTE-A AT&T LTE Communicator installed take note. Resideo has identified an issue where, after the AT&T 3G sunset on 02/22/22, any panel not properly updated will lose its connection with the cellular network. This issue does not affect Verizon units.

The firmware version that resolves this issue is 01.09.07772.494, and it is available now on the Resideo AlarmNet360 servers. The issue at play here is that the AT&T cellular communicator currently falls back on the 3G network when it can't connect to LTE. Once an LYRICLTE-A communicator is registered, it looks for both an LTE signal and a 3G one. Without this critical firmware update, these communicators would continue to look for a 3G signal after the 3G sunset. Being unable to find a 3G signal, they will lose connection and go offline.

Users who find themselves in this situation have a few options. If you are a Lyric Alarm System user with the AT&T LTE communicator installed, you can choose to go ahead and manually update your system now. The system needs to be disarmed and have no trouble conditions present in order for the firmware update to go through, so a manual update allows you to choose a time when it is disarmed and ready. It also allows you to confirm that the update was successful after you see your panel reboot.

Since this is a critical update, AlarmNet will begin automatically updating panels that are affected by this issue starting on December 8, 2021. Since a firmware update can only go through when the panel is disarmed with no troubles, any users with a zone trouble, or a low battery message that they have been putting off correcting, should go ahead and take care of the issue. Once all trouble conditions are clear and the system is disarmed, we recommend that you go ahead and manually perform the firmware update. Instructions for updating are linked above.

If your system is automatically updated, it will reboot as part of the update process, so don't be alarmed if you see this happen. Step 3 in the FAQ on updating the panel linked above shows you how to confirm the panel's firmware version. So, if you see your panel reboot you can verify that an update was successfully completed.

Any Lyric Controller with a LYRICLTE-A AT&T LTE Communicator that is being installed on or after 02/22/22 will need to be updated to firmware version 01.09.07772.494 via the built-in WIFI communicator before the LYRICLTE-A will work properly. The firmware update should be completed prior to the installation of the LYRICLTE-A. The LYRICLTE-V Verizon LTE Communicator is not affected by this issue. You can read the full notice from Resideo here.

Local Alarm Mode, also called Demo Mode, is a way for an alarm dealer to demonstrate the full features of the panel without having to register it to an AlarmNet360 account. However, while in this mode, panel communications can't be configured. A panel in this mode can seem to be broken.

Alarm Grid has seen several of the Honeywell Home PROA7, Honeywell Home PROA7PLUS, Resideo PROA7C, and Resideo PROA7PLUSC panels recently that have either arrived with Local Alarm Mode enabled, or have been put into this mode during initial setup. Once Local Alarm Mode has been enabled, it is impossible to configure the panel communication settings until Local Alarm Mode has been toggled off.

Local Alarm Mode is a valuable tool that has been made available to alarm dealers so that they can demo these new panels for a customer in spite of the fact that the panel isn't associated with an account. This was particularly important when the panel was first introduced because there was no local programming. For those early panels, until the ProSeries panel was registered, it couldn't do much unless Local Alarm Mode had been enabled.

This was a great tool at the time for alarm dealers, but for DIY customers, it doesn't offer much in the way of benefits. Now that the panel has local panel programming available, there really is no reason for an Alarm Grid customer to want to use this feature. Whether the panel arrived with this feature enabled, or the feature was enabled during programming, once the customer decides to have the system monitored, whether self monitored, or with central station monitoring, Local Alarm Mode should be disabled.

To check to see if Local Alarm Mode is enabled or disabled, choose the Menu icon (≡) at the bottom center of the Home screen. Select Tools > Installer Code (default is 4112) > Local Alarm Mode. The feature can then be toggled OFF if it is enabled. If it was enabled and you toggle it off, you'll see a confirmation screen, click on the "YES, DISABLE" option.

If you've been using the system with Local Alarm Mode enabled, and you have signed up for alarm monitoring with Alarm Grid, be sure to toggle this feature OFF as soon as possible. Depending on which monitoring plan you sign up for, activation of your account may begin immediately after sign up, and having this feature enabled at that time can cause delays. This is particularly true of the Self-Monitoring options. If you signed up for a central station monitoring plan, just be sure to disable this feature prior to your activation appointment.

Resideo and Honeywell Home have just released Firmware Version 03.592.107.0 for the PROA7 and PROA7PLUS panels. This update allows the PROTAKEOVER module to support 5800 Series life-safety sensors like the 5808W3, 5800CO, and more. In addition, it offers some other features and improvements.

There are four (4) different panels in the Resideo and Honeywell Home ProSeries lineup. The Honeywell Home PROA7, and Honeywell Home PROA7PLUS, and the Resideo PROA7C and Resideo PROA7PLUSC. The 03.592.107.0 Firmware Version applies to all of them. The differences between the Resideo versions and the Honeywell Home versions are purely cosmetic. You can find details about that in a previous post.

The biggest news in this firmware release is the addition of life-safety support when using the PROTAKEOVER module. For the Honeywell 5800 Series legacy RF sensors, the use of life-safety sensors such as the 5808W3, 5806W3, 5800CO, and others has actually been ETL tested and passed to the UL Residential Fire standard. When taking over a CO detector, be sure to check the expiration date. CO detectors are usually good anywhere from six (6) to ten (10) years. Life-safety sensors from any of the other manufacturers supported by the PROTAKEOVER, including DSC (433 MHz), Bosch (433 MHz), 2GIG (345 MHz), Qolsys, and Interlogix (319.5 MHz), can be used, but they will not meet the ETL listing requirement.

When life-safety devices are used with the PROTAKEOVER the functionality for Loop 2 becomes automatic. For sensors programmed for Fire, Loop 2 automatically becomes the Maintenance (Clean Me) input. For those programmed as Carbon Monoxide, Loop 2 automatically becomes the End-of-Life input. For this reason, if you use a 5817CB or 5817CBXT, for something such as a wired heat detector input, you MUST strap out the loop 2 input, either with a wire jumper or a resistor, depending on which 5817 you're using, and you cannot use that input for a zone on the system.

Although the addition of life-safety support for legacy RF sensors is the big news in this firmware release, it is by no means the only news. This revision adds the ability to enable or disable on-screen panic alarms. It also adds the ability to program scenes via Total Connect 2.0 that pertain to alarm panel arming and disarming events only. Even if the panel itself doesn't have a PROWIFIZW module installed (Smart Home monitoring plan is still required). Prior to this release, if you had no intention of using Z-Wave devices, but you still wanted to program your system to arm or disarm based on a schedule, you couldn't do so unless you installed a Z-Wave controller in the panel.

Below, we'll list all the added or updated features with an explanation of each:

• Zone Response Type Enhancement: The Device Type "Other" now offers the option to enable Chime. The PROSIXC2W now supports 24-Hour panic response types including 24-hour Silent, 24-Hour Audible, 24-Hour Medical, & 24-Hour Auxiliary. All Device and Response Types are now available when enrolling wireless zones using the PROTAKEOVER module.
• LCD Keypad (PROSIXLCDKP) Enhancement: Now, when a Duress Code is entered at the wireless LCD keypad, only the 4-digit code is required. Previously, users would have to enter the 4-digit code + OFF [1].
• Quiet Time Feature Added: The PROWLTOUCH Keypad now participates in Quiet Time (10:00 pm - 8:00 am). This means that non-emergency Trouble conditions, and Low Battery troubles will not sound the keypad during this time, though they will display. Included in this list are Communicator Trouble, System Low Battery, RF Transmitter Low Battery, RF Jam Trouble, AC Loss, and PROWLTOUCH Supervision Trouble. Sensor Tamper, and RF Supervision will sound. At 8:00 am, if the non-emergency trouble condition still exists, it will sound. This feature is automatic. It cannot be disabled, and the times cannot currently be changed, though that may change in future revisions.
• Additional PROWLTOUCH Enhancements: While in backlight timeout, if the keypad reconnects to WIFI for any reason, the keypad will not illuminate. Keypad supervision is now defaulted as "Disabled". If a system has PROWLTOUCH keypad supervision enabled, updating to this version will NOT disable it. The Wireless Touchscreen keypad can now only be enrolled when the main panel is not in program mode. This prevents conflicts with the PROSIXLCD which MUST be added through panel programming. An issue has been corrected where, if the keypad locked up, the battery had to be removed and re-installed in order to reset the keypad. The Indoor MotionViewer (PROINDMV) clips can now be played back on the PROWLTOUCH as well as on the main panel.
• End-user Can Push User Codes to Z-Wave Locks From TC2: Whew, that was a mouthful! Any Total Connect 2.0 Admin user can now create a user code and send it to a Z-Wave lock via either the Mobile App, or the Website. They have the option to both Push the User to the Lock, and allow the Lock Disarm by that User to automatically Disarm the system.
  
  
• Improved TC2 Behavior During a Z-Wave Lock Jam: Previously, when a lock jam condition was displayed, the only option available was to physically go to the lock and toggle the lock position. Total Connect 2.0 now gives you the option to attempt to Lock or Unlock through the app or website.
• Z-Wave Lock User Code Sync Improvement: In the past, setting the panel user code to match the Yale lock user code would cause issues. This is still not recommended, but the behavior should be improved.
• Security Scenes Available in TC2 Without PROWIFIZW: There is no longer a hardware requirement that the panel have the Z-Wave Controller installed in order to create TC2 Scenes pertaining to security panel-only scenes. Currently, the security system scheduling is only available for Partition 1, and a plan that includes automation (Smart Home) is still required.
• Improved Skybell and TC2 Syncing: Some doorbell cameras were having issues syncing with TC2 after the previous firmware update. Those issues should be resolved.
• Improved PROSIX RF Signal Level Indication: The system now refreshes signal level for PROSIX devices immediately upon entering walk-test mode.
• Improved TC2 Camera List Sync: In the past, it was sometimes necessary to Sync the panel twice to get an accurate camera list. This has been improved.
• Partition Master User Enhancements: A Partition Master User can now only see event logs for the partition(s) they are authorized for.
• Language Corrections: Improvements in translations for both French and Spanish.
• Cyber Security Updates: Ongoing Cyber Security maintenance, as well as other bug fixes.

This firmware update can currently only be installed via WIFI. Any account communicating via cellular only will need to be connected to a mobile hotspot or other "WIFI" option before it can be updated. The size of this update is approximately 8MB.

This is a huge update with a lot of feature additions and some user-recommended improvements. Leave a comment below and let us know what you think about the ProSeries panel and the 3.5 update. As always, we look forward to hearing from you!

AlarmNet360 is both a website and an app that can be used to create, edit, and cancel AlarmNet accounts. Access to this website and app is only available for licensed alarm dealers who are affiliated with AlarmNet. As an end-user you will not need to have or create an AlarmNet360 account.

Being a DIYer in the alarm industry can be pretty confusing at times! Nearly all of the documentation provided with alarm systems that have historically been installed only by alarm professionals is intended only for alarm professionals. So, when you buy that new ProSeries or Lyric Alarm System, and you begin reading the installation instructions, one of the first things you are told to do is create an AlarmNet360 account. This is not something that you, as a DIYer will be able to do.

This is where Alarm Grid comes in. Alarm Grid is a DIY friendly company. We sell professional grade alarm systems to anyone who wants to buy them. Sometimes, alarm professionals purchase from us and then they go about configuring the system themselves because they have access to AlarmNet360. Sometimes, customers purchase from us and then hire their own alarm professional to install their system and that alarm professional completes the setup on AlarmNet360 themselves. But usually, when an individual buys a system from us, they then sign up for one of our no-contract monitoring plans, and then we set up their account through AlarmNet360.

The relationship between Alarm Grid and our monitoring customers is a symbiotic one. DIY alarm users choose not to pay a professional to do something that they can do themselves. That being the physical installation of the alarm equipment. With the proliferation of self-contained, all-in-one systems, installation has gotten more and more simple. A child can do it. We have several young customers in their teens who set up systems just because they enjoy doing it, and figuring out new and interesting ways to make things happen.

On the monitoring side of things, that's where restrictions start to come in. There are certain things that have not opened up to DIYers yet, and access to AlarmNet360 is one of those things. You may be thinking, "Forget AlarmNet360, what's AlarmNet?" You can read about AlarmNet here. At present, only alarm dealers can sign up for access to AlarmNet360 in order to be able to add, edit, or cancel AlarmNet accounts. Access to accounts is very tightly controlled. The only accounts that Alarm Grid can see in AlarmNet360 are accounts that are assigned to Alarm Grid, which usually means that Alarm Grid created them in the first place.

Alarm Grid chose the DIY business model in part because we have everything we need to administer accounts on the back end, but we don't have a team of installers to send out and put in systems. DIYers are our installers, and in turn we provide for them the account admin services that they are not allowed to perform for themselves. We sell reasonably priced, professional grade alarm equipment. The same equipment that just about any alarm dealer in the country will sell you, and we handle the administrative side of things, in addition to providing free, world-class technical support to our monitored customers. In exchange for that, we charge a reasonable monitoring fee with no activation fees, no cancellation fees, and no contracts. We also don't care if you buy your system from us or elsewhere. We will monitor any equipment that is within our power to monitor for the same prices we charge to monitor the equipment we sell.

So, when you crack open that new system, and start reading the instructions, skip the part where it talks about the AlarmNet360 account. Whoever you sign up for monitoring with will take care of that part. Do you have an AlarmNet communicator? Have you been stumped by the mention of AlarmNet360 in your system's documentation? Leave us a comment below and let us know if this information was helpful. We always look forward to hearing from you.