Monitored Home Security Systems Posts

Hi DIYers! Today, we're presenting our own guide for installing the Qolsys IQ Panel 2 Plus. This system is very easy to use, and it can be installed by virtually anyone using nothing more than a screwdriver! This is the perfect security system for your home, office, or apartment!

Most of the information presented in this post can be found in the Qolsys IQ Panel 2 DIY Installation Manual. You are free to follow along with that manual, which can be found here. We also have three (3) videos that we will include along the way. Feel free to follow along with those as well. All of this information applies to both the original IQ Panel 2 and the newer IQ Panel 2 Plus. With that out of the way, let's get started!

The first thing you will want to do is power on the system. The Qolsys IQ Panel 2 Plus comes with everything you need to get started. Once you have opened up the box, you should locate the panel, the power supply transformer, the power wire, the panel back cover, and the table stand. You will also want to have a screwdriver on hand.

Start by connecting the spade lugs of the power cable to the transformer. The IQ Panel 2 Plus uses DC power, so you must make sure to follow polarity. That means connecting the positive (+) wire and negative (-) wire accordingly. The positive and negative ends on the IQ Panel 2 power cable are marked for this purpose. The positive (+) wire has grey dashes and ends in a red spade connector. The negative (-) wire is solid white without grey dashes and ends in a black spade connector. Make sure that the wires are connected with the proper terminals on the transformer. You can see the positive (+) and negative (-) terminals marked on the transformer. The connection should be nice and snug, but not overly tight.

From there, you can connect the other end of the power cable to the IQ Panel 2 Plus System. There is a simple barrel connection for this purpose. The transformer can then be plugged into a wall outlet. When applying the panel back cover, make sure to run both the power cable and the thin RF receiver cable out from the indentation on the back cover. The back cover should snap nicely into place. The convenient table stand can be installed by putting it into the keyhole slots on the back of the panel and then sliding up. You can power on the system by pressing and holding the side power button until the system LED remains lit.

After the system powers on and boots up, you will be greeted by the Setup Wizard. It is recommended that you go through the Setup Wizard, as it will walk you through the entire setup process. Note that some steps of the Wizard will require you to activate the system for monitoring service. This involves registering the panel's built-in cellular communicator with Alarm.com. This is optional for initial set up. You can always register the cellular communicator with Alarm.com later.

Remember that activating the system is something you will definitely want to do before too long, as that is the only way for it to send out signals to you and/or a central station. Remember that you will need to provide the IMEI Number for the system in order for your monitoring company to activate the cellular communicator. This can be found on a sticker on the back of the panel. It will also be shown as you move through the Wizard.

You will do several things as you go through the Setup Wizard. You will connect the system to a WIFI network, run an initial check for the system, add sensors, perform an initial sensor test, set up the built-in panel glass break sensor, add Z-Wave home automation devices, pair your phone for automatic Bluetooth disarming, pair secondary IQ Remote Keypads, and add system users. Remember that you will want to have a good idea of Sensor Groups when enrolling sensors. You can learn all about the IQ Panel 2 Sensor Groups in this helpful FAQ.

The last thing you will want to do is install your sensors. We only focused on door and window contacts and motion sensors, but many of the same principles apply across any sensor type. What's great about wireless sensors that are used with the IQ Panel 2 Plus is that they can be mounted without drilling holes into the wall or using any power tools. You can safely mount and secure these sensors using double-sided foam tape. Most wireless sensors come with their own double-sided tape for this purpose, or you can buy some off our site!

There are a few general tips when mounting these sensors. When mounting door and window contacts, you should have the magnet on the moving structure of the door or window, and the sensor itself on the door or window frame. Make sure the magnet is aligned with any indication marker shown on the sensor. Also remember to keep the magnet spacing gap in mind. Most Qolsys Door and Window Sensors allow for a magnet spacing gap of up to 0.75 inches.

As for motion sensors, you should have them mounted flat on a wall or corner-mounted. But keep in mind that only a flat-mount will allow you to install without drilling any holes. The motion sensor should be nice and level, and it should be installed at a height between 6 and 8 feet. Qolsys recommends 7.5 feet, which provides the best possible results. The motion sensor should not be facing any windows, vents, or air ducts. It should also not be facing any nearby furniture or stairwells if you have pets!

Most importantly, remember to test ALL your sensors after the final installation!

And that wraps up our Part 1 Guide for installing and using the Qolsys IQ Panel 2 Plus. Look forward to Part 2 coming soon! If you have any questions about the Qolsys IQ Panel 2 Plus or our monitoring service, please reach out to us by emailing support@alarmgrid.com. Remember that our support hours are from 9am to 8pm ET M-F. We look forward to hearing from you!

If you have a security system, then you will want to make sure that it can detect intruders coming into your home. But predicting how an intruder will enter your home can be easier said than done. You need to be prepared for all situations. Here are the Top 5 ways intruders enter homes.

Through the Front Door

It really shouldn't come as much of a surprise that many intruders simply walk right through a home's main point of entry - the front door. We've all forgotten to leave a door locked at some point. Many intruders will simply try the front door to see if it's unlocked. This is often associated with burglaries that aren't pre-meditated. Keep in mind that many burglars don't plan ahead of time. Instead, they just see a house that looks attractive, and walk in through the front door.

Arguably the most important sensors you should have enrolled with any security system are door contacts, and for good reason. These are the devices that will alert your system in case someone ever enters your home through the most obvious way. Door sensors are extremely easy to enroll, and there are so many different options available. You will have no trouble finding a door sensor that meets your needs and requirements.

Breaking a Window

Not every intruder will enter your home in a "polite" manner. There are many burglars who won't hesitate to use brute force and smash in a glass window. And this can be more difficult to stop, as a locked window won't really stop an intruder from smashing. This isn't as common as walking in through an open door, but it certainly does happen, and you really should be prepared.

There are two sensor types that come to mind for detecting broken windows. The most obvious is a glass break sensor. These devices will actively listen for the sound of glass being broken, and they work great with nearly all types of windows. You might also consider installing motion sensors in rooms with windows. Then an intruder will be detected as soon as they enter through the window. It is always a good idea to back up a glass break sensors with a good motion sensor. There are instances where a glass break sensor cannot detect glass breaking. An example of this is when a bullet is fired through glass.

Through the Garage Door

Forgetting to close your garage door on an attached garage can provide easy access to your home. It can be easy to have that daily task slip your mind. There are many times when we get home tired after a long day, and just forget to close the garage door. Or maybe you forgot to close it as you were leaving for work. It happens to all of us. But a potential burglar walking by will see this as an opportunity!

Just like the other points of entry for your home, garage doors can be monitored. There are special garage door sensors available for this exact purpose. You might also consider getting a Z-Wave garage door controller for the system. This way, you can use Total Connect 2.0 or Alarm.com to close your garage door from pretty much anywhere. This is great if you ever forget to close it!

Climbing a Tree or Fence

Okay, you might think this is a bit silly, but we're serious here. If you have a multi-story house, don't think that an intruder will hesitate to use your home's surrounding to gain entry to a higher floor. This could include climbing a tree or a large fence and then entering through an unlocked window. Like we said, it's best to be prepared for any and all situations.

There are a few things you might do to combat this. The most obvious is to always make sure all your windows are locked, even the ones that cannot be easily accessed. But you might also want one or more outdoor motion sensors to detect any movement that may occur around your home. Outdoor security cameras are also a great idea!

Skylights

If your home has skylight windows, don't rule them out as a point of entry for an intruder! These high up windows look great in a home, but they can be easy pickings for a burglar who can reach these points. This isn't something every homeowner will need to worry about, but do keep this possibility in mind if your house has this decorative feature.

Many of the previously mentioned devices are good for monitoring skylights. You can put motion sensors in a room with skylights for the system to detect if anyone comes in from high above. Glass skylights are also perfect for use with glass break detectors. And installing some security cameras in the room never hurts!

Alarm Grid is here to help you provide top-quality protection for your home. We have all the gear you need to make sure that your system can detect intruders from any point of entry. If you need help choosing equipment, or if you want to learn more about our monitoring services, please reach out to us. The best way to contact us is to email support@alarmgrid.com. You may also call us at (888) 818-7728. Remember that our support hours are from 9am to 8pm ET M-F. We look forward to hearing from you and helping you set up the perfect security system!

Hi DIYers! Last week, we sent a small team to Silicon Valley, California to check out the 2019 Qolsys Summit. Needless to say, we were absolutely blown away with what Qolsys will soon be offering. Today, we would like to focus on some of their new industry-changing products in the pipeline.

The biggest highlight of the Qolsys Summit was the opportunity to check out the newest upcoming panel from the company, the Qolsys IQ Hub. The IQ Hub represents the vision of Qolsys to bring home security closer and more accessible to the average consumer than ever before. This is truly the optimal system for any budget-conscious consumer who wants to bring state-of-the-art security and technology into their home. It is slated for a Q1 2020 release.

We do not have all the details on the Qolsys IQ Hub quite yet. But there is still a lot that we can talk about. The most obvious addition to the Qolsys IQ Hub is its prominent speaker on the front. Qolsys is expected to introduce some mind-blowing integrations for the system that will turn your alarm control panel into a compact entertainment center.

Remember that Alarm.com already offers an excellent Sonos integration. We are sure that the IQ Hub will take full advantage of this feature and truly put it to great use. Our team did get a chance to test the IQ Hub sound quality, and we can confirm it sounds just as good as any high-end portable speaker. This is highly impressive, and we expect many users to be thrilled that their alarm system can now essentially double as a party-starter.

The next aspect you will likely notice about the IQ Hub is its standout display screen. This is a 7" touchscreen display that appears to have even higher resolution than any existing security system on the market. We do not have the exact specifications on the screen just yet, but it certainly passes the eyeball test. And as you can see from the photo above, the slideshow feature returns. Get ready to show-off some of your best photos on the Qolsys IQ Hub!

As we mentioned earlier, Qolsys seems to be envisioning the IQ Hub as a way to make the home security market more accessible to the average consumer. The new system is not expected to replace the existing Qolsys IQ Panel 2 Plus, but it is anticipated to have a lower price point. We also expect many existing features to return to the IQ Hub, including built-in WIFI, Bluetooth connectivity, cellular LTE, and Z-Wave Plus functionality.

One thing that will not be returning to the IQ Hub is support for legacy sensors (e.g. 319.5 MHz, 345 MHz, and 433 MHz devices). The new system will be entirely PowerG, and you will need to use those sensors with the system. This is fine, as PowerG Sensors offer an impressive wireless range of up 2,000 feet when used with the IQ Hub in open air. They also utilize military grade 128-bit AES encryption in all their communication to ensure maximum wireless security.

Another interesting note about the panel is that it is not designed to be opened up. This is a significant change from most existing security systems, where you will occasionally need to open up the panel to make hardware changes. The battery on the IQ Hub is sled-replaceable, and it can easily be swapped out by the end user with little effort. All of the hardware is built right in, so you will never have to make any changes in that regard. Talk about DIY friendly!

Qolsys made other various enhancements to the IQ Hub System. They touted an improved integrated camera, and it can even double as a motion sensor by detecting changes in pixelation. We also expect this feature to be used in conjunction with Alarm.com so that you can take a peak-in at your home while you're on the go. You will also notice the LED light on the front of the panel. This light changes colors to let you know the current system status. How cool!

The system also features a built-in microphone that you can use to get alerts regarding loud sounds. You can even adjust the minimum sound level required to trigger alerts. This is perfect for parents who want to know if their baby is fussing or for owners of rental properties who may want to be alerted if their guests are throwing a loud party. It's just another way that Qolsys is working hard to keep you connected with your home.

We do expect that there will be some hardware limitations of the IQ Hub when compared with the IQ Panel 2 Plus, especially when you consider the anticipated lower price point. Qolsys most likely reduced costs by dropping legacy sensor support. It's also possible that the IQ Hub will support fewer zones than the IQ Panel 2 Plus (128 zones). But we cannot confirm the exact number of zone on the IQ Hub at this time. The IQ Hub is also slightly larger than the existing IQ2+ due to the added speaker.

As stated earlier, the Qolsys IQ Hub is scheduled for a Q1 2020 release. This groundbreaking new system is sure to make some big waves in the security industry, and we are confident that it will help many new users get their start with home security. We can't wait for its release, and we hope you're excited too!

Qolsys also unveiled another interesting product at the event, the Qolsys IQ Router. At first glance, you might be wondering what's the big deal. What's so exciting about an IP router? Well Qolsys packed in some game-changing features that are sure to make the IQ Router the perfect addition to your IQ Hub or IQ Panel 2 Plus System. It is sure to make your life more convenient in many ways. And we can also confirm, it is dual-band with support for 2.4 GHz and 5 GHz!

At the basic level, the IQ Router is exactly what it sounds like, an internet router. It replaces the existing router for your home's IP network. But what you get with the router is pretty ingenious. Any Qolsys IQ Panel 2 System or Qolsys IQ Hub connected with the IQ Router can be accessed remotely by your alarm monitoring company for programming purposes. This is similar to what the DSC Iotega offers. But with the Qolsys Systems, it is optional rather than mandatory.

Of course, if you don't want your monitoring company accessing your panel, then you can disable the feature. But it's pretty nice if you want assistance with programming new devices. One thing you will certainly love is its ability to auto-discover your IQ Hub System and automatically enroll it with your WIFI network. You can even configure your IP settings right from the IQ Hub. This truly makes the IQ Hub the central controller for your entire network!

Another innovation from the IQ Router is the ability to auto-enroll guest WIFI devices. In other words you can get any visitors on your WIFI network, without making them enter a long, tedious password. The way this works is that your guest will request to join the network from their IP device. You will then approve the request from either your IQ Hub or an app on your phone. And just like that, your guest will be connected with your WIFI network. Super convenient!

As you will notice, the Qolsys IQ Router only has one (1) LAN port for connecting a hardwired ethernet device. This isn't a big deal, as most users might not even need one. If you need additional ports, then you can easily connect a network switch to the router and use it however you would like.

But one very exciting feature of the IQ Router is its ability to support up to eight (8) WIFI extenders or access points. This makes it truly suitable for even large commercial locations! The router facilitates a total mesh network to help ensure that all of your IP devices stay connected across even an incredibly expansive area. Whether your needs are big or small, you are sure to get great use out of the new IQ Router! Qolsys states that it should be out by the end of this year.

We would like to end this post with some smaller product announcements we heard at the Qolsys Summit. A PowerG 360-Degree Ceiling-Mount PIR Motion Sensor called the PG9862 was unveiled. This sensor is perfect for use in closets or in commercial locations where corner-mounting is not feasible. The PG9862 is available from Alarm Grid now, and you can get it right here.

Lastly, we heard rumors about a much-anticipated PowerG Wired to Wireless Converter. This is huge news, as it will allow you to takeover an existing hardwired system and use a Qolsys IQ Panel 2 Plus or Qolsys IQ Hub in its place. And of course, all your hardwired sensors will enjoy the amazing range and security of the PowerG wireless protocol. We do not have any other details on the PowerG Converter at this time, but we will definitely keep our eyes peeled.

We hope that you are eagerly awaiting all of these new products just like we are! This was truly an awesome event that Qolsys put on, and we are thankful that we got to be a part of it. We are hopeful that Qolsys hosts a similar gathering next year in 2020! For now, check out these new and upcoming products, and email us at support@alarmgrid.com if you have any questions or thoughts. Remember that our support hours are from 9am to 8pm EST M-F. As usual, we look forward to hearing from you!

When thinking about home security, many people mistakenly believe that it is always an expensive endeavor. The truth is that the cost can range from extremely affordable to exceedingly pricey. Today, we're here to tell you that home security does not have to cost you an arm and a leg.

Setting up a home security system is a worthwhile investment for any homeowner or renter. Protecting your assets is extremely important, and you can even save money on your homeowner's insurance. And if you decide to move, you can either bring the system with you, or leave it at the property to increase your home's resell value.

How much you spend on home security truly depends upon your needs. While you can certainly spend a large sum of money monitoring your home, the reality is that you don't have to break the bank. At Alarm Grid, we offer monitoring plans for all budgets. Our self-monitoring plans start at just $10 per month, while our central station monitoring plans start at just $15 per month.

Keep in mind that you will needs a central station monitoring plan to receive a certificate of alarm (CoA) and save money on your homeowner's insurance premium. These savings can vary significantly, so make sure to check with your insurance company to find out how much you can save. Many homeowners find that monitoring an alarm system actually pays for itself due to the insurance savings!

The system you purchase also makes a big difference in your monthly monitoring costs. Many panels require you to upgrade to a cellular plan for monitoring service. Cellular monitoring has a higher monthly cost than IP-only monitoring, so make sure to keep this in mind. Although we always recommend using cellular for its superb reliability, we also understand that some users are comfortable with IP monitoring service.

If you do decide to go with IP-only monitoring, just make sure that the internet in your home is reliable. A downed internet connection will leave your home unmonitored and vulnerable. You will also want to get a panel that can be used with IP-only service. Nearly all of the Honeywell Panels we sell are suitable for this type of monitoring.

We recommend the Resideo Lyric Controller for IP-only monitoring. This system has a built-in WIFI card, so you won't need to get any add-ons to get the panel up and running.You can also easily add a cellular communicator if you decide to upgrade your service later on. We also sell some Lyric System Kits that include everything you need to get started with alarm monitoring service. There is a 3-1 kit for smaller homes, and a 10-1 kit for larger homes.

Also remember that you do not need to buy a system from Alarm Grid to receive our monitoring service. If you can find a system elsewhere for a lower price, then go for it. We do recommend contacting us before making the purchase to make sure it's a system we can monitor. Our security system planners will be glad to help you design your system from start to finish.

What else can you do to keep costs low? Well we definitely recommend going with a DIY, no-contract monitoring company like Alarm Grid. DIY means do-it-yourself. You can save hundreds or even thousands of dollars by installing your security system yourself. While installing your own system might seem like a challenge, it really doesn't have to be. In fact, the Lyric Kits we mentioned before can technically be installed using nothing more than a screwdriver!

The other important thing is to make sure the security company you choose is no-contract. You can be left on the hook for huge amounts of money if you get stuck in a contract. And if there's ever an emergency and you need to suddenly cancel your service, you will be very glad that you chose a no-contract company. At Alarm Grid, you can easily discontinue your monitoring service at the end of your monthly payment cycle and then resume service when you are ready.

Also remember that Alarm Grid has no added fees. This means that you never pay extra to start or stop your service. What you see is exactly what you get. We do this to make our monitoring service as accessible to many people as possible. If you are intereste in learning more about what we offer, we encourage you to check out our monitoring page for more information.

You are also more than welcome to talk with us before you make your decision. We would love to speak with you if you have any questions or concerns. The best way to get a hold of us is to email support@alarmgrid.com. We will check your email at our earliest convenience and reply back as soon as possible. You may also call us at (888) 818-7728 during our regular business hours of 9am to 8pm EST. We look forward to hearing from you, and we hope to make you a valued member of the Alarm Grid family!

Taking a summer trip DIYers? You need peace of mind to maximize your fun. Knowing that your home is safe and operational is a great feeling. You have a lot of planning before you go on vacation, and we're here to help you get ready. Here are some ways you can prepare for your next vacation.

Get a Smart Thermostat

A smart thermostat is the perfect accessory if you plan on taking a trip during the summer months. It's hot out! You don't want to come home and suddenly discover that your HVAC system has stopped working. The last thing you need when you come home is an uncomfortable house. You can pair your smart thermostat with your security system and start using it with an interactive platform like Total Connect 2.0 or Alarm.com. While you're on the beach or lounging by the pool, you can check your home's temperature and make sure it's reasonable. You don't want to set the temperature too low; there's no reason to waste the extra energy. But you can check and make sure that it's at a reasonable level to know that your HVAC system is working properly. You can even set up automatic notifications if the temperature gets too high.

We actually just made a post showing-off some of the best smart thermostats on our site. Check it out!

Get a Smart Door Lock

Let's say that your smart thermostat shows a very high temperature, and you suspect your HVAC system might be broken. How are you gonna let the repair person inside? You're on vacation, and you triple-checked to make sure your doors are locked! Well with your smart door lock, you can let the repair person inside and then lock the door behind them when they leave. What about your plants or your puppy? Your friendly neighbor is going to need to get inside to take care of them. You don't have to give them a key. Just make them a guest code on your smart lock, along with a guest code on the panel. Or if you are extra cautious, you can always lock and unlock the door and arm and disarm your system from TC2 or ADC. This is the perfect way to make sure that your home stays in order while you're off relaxing somewhere far away.

We did a post a few months ago on some great smart door looks. Take a look!

Get Alarm Monitoring

You won't able to use your smart door lock and your smart thermostat without a hub. And what better hub than a brand-new security system? At Alarm Grid, we have all you need to make sure that your home is safe and secure while you are gone. If someone dares to break-in to your house while you're off on the vacation you worked hard for, we'll make sure that they pay the price. We offer monitoring plans that will connect your alarm system with a 24/7 central station for automatic police dispatch in these serious situations. The smart home control features are a nice touch, but keeping your home and your possessions safe is always a top priority. We have many alarm panels and security sensors to protect homes big and small.

We recently did a comprehensive post covering all our available monitoring plans. Here it is!

Get Environmental Sensors

Protecting your home from a robbery is important, but what about environmental conditions? There could be a water leak that causes a flood in your basement, or maybe a wildfire affects your property. It would also be a real bummer to come home to a natural gas leak. We have sensors for all these situations. You can get flood sensors, smoke and heat detectors, and natural gas detectors all from Alarm Grid. Your Total Connect 2.0 or Alarm.com service will send you a text and/or email alert so that you know about the activated sensor as soon as it happens. And if it's something serious like a fire, emergency help will be sent out if you have central station service. Alarm Grid has all the environmental sensors you need to know that your home is ready for your vacation.

We know what happens when people don't use environmental sensors. Don't let this happen to you!

Contact Us!

You need to do one last thing before you Arm Away, lock your smart lock and set your smart thermostat schedule. That is contact Alarm Grid to let us know about your vacation plans! If you want any changes for the dispatching process, make sure to inform us. This could include something like having the central station call your neighbor or your friend instead of you while you're away. Letting us know about your vacation schedule is also extremely important if you plan on having someone else looking after your house while you are away. You should let us know that a neighbor or a friend will be using your system during this time. You might even tell us which user code they will be using so that we know to look out for anything unusual. This is really only necessary if you need temporary changes to your account while you are gone.

If you need to let us know about your vacation plans, you should send a quick email to support@alarmgrid.com. Our support team will check your email as soon as possible and put the necessary information on your account. Enjoy your vacation, and stay safe and relaxed with Alarm Grid on your side!

If you're taking the leap into the exciting world of home security, one of the first decisions you will make is whether to hire a professional installer or to install the system yourself. While most new users still hire a professional, installing your own system is often the better option.

Many people mistakenly believe that a home security system is difficult to install and that it has to be done by a professional. But the industry has actually made great strides in recent years, and now alarm systems can be installed by almost anyone. DIY monitoring companies like Alarm Grid have helped to make this possible. We've shown the security industry why the DIY model is the right model for alarm systems. Now you too can install your own home or business security system! Simply obtain the equipment you need, either from our website or from somewhere else, and sign-up for one of our alarm monitoring plans to get started.

The key to setting up your own home security system without hiring a professional is to make the installation as easy as possible. Choose a wireless control panel and wireless sensors that don't require holes to be drilled. Most wireless panels can be rested on a desk or table with a compatible desk mount, and the sensors can be mounted using double-sided foam tape that often comes included. From there, you just need to program the sensors, which is super easy when you own your own system and know the proper access codes. Before you know it, you will be a true DIYer!

Here are ten reasons why you should install alarm system instead of hiring a professional:

1. Understand Your System Better

When a professional installer sets up your own home or business security system, they usually aren't there to play teacher. They will often show you the bare minimum so that you can perform basic functions on the system. By setting up your own system, you can understand its features and capabilities better. This way, you can configure the system exactly to your liking to suit your lifestyle!

2. Choose Your Own Equipment

If you hire a professional, you might have little say over what equipment will be used in the installation. To have full control over what equipment is used, your best bet is to install the system yourself. If you need help choosing your equipment, Alarm Grid offers free support online and over the phone in planning home and business security systems. And with a DIY monitoring company like Alarm Grid, it doesn't matter where you find the equipment. If you can find it cheaper outside our website, go for it!

3. It's More Satisfying

We've discussed the IKEA Effect in the past and how customers who install their own equipment are more satisfied with the end result than if they had someone else do it for them. When you put in the time and effort to set up your own alarm system, it becomes much more valuable and personal to you than if you just throw money at someone to get the job done. Users who complete their own installation grow to love their alarm systems and the protection they provide for their families.

4. Save Money

This one is obvious. Installers charge hundreds or even thousands of dollars for most alarm system installations. Just check out the hourly rates for most outside installers. It's staggering! The truth is that you can install your own equipment just as well as a professional, all without having to spend a cent. So roll up those sleeves, get an Alarm Grid Tech on the phone, and save some money by installing your own system!

5. Feel Empowered

Installing your own alarm system is empowering. It offers a feeling of accomplishment in knowing that you did it yourself. You don't have to rely on others to install the system for you. Instead, you are self-sufficient and in control. Of course, if you ever do need some assistance, our technicians can walk you through the process online or over the phone. But you're the one in control of the project. You have the power!

6. Learn Something New

Many people enjoy learning new processes and tasks. Why not learn how to install and program a security system? It can actually be a fun and amusing challenge to take on for yourself, and it's knowledge that might come in handy later. After you've installed your own alarm system, you can add it to the list of things you know how to do. And it might make for interesting conversation to teach others about the system as well.

7. Make Your Own System Changes

Almost all alarm system users will need to make changes and adjustments to the settings at some point or another. For users who hire a professional, they often don't know the system's Installer Code, and they have to have an installer come out to their home or business to make the changes. But if you install your own system, you'll know the Installer Code so you can go right in and make your own changes in a matter of minutes. How cool is that?

8. Easily Move Your System

Are you planning to move to a new home? Do you need to take your business security system to a new office? If you set up your own system, this process is a breeze. Simply dismount your equipment, and set it up in your new location. You will need to contact your monitoring company and let them know about the address change, but the transition is seamless overall. Remember to test your sensors after moving them to your new home or business!

9. Complete Ownership

It's a common tactic for other security companies to offer a free installation and a free security system when signing-up for their monitoring services. The problem with this is that most of these companies offer proprietary equipment that will only work with their services. So while you might own the system, it's no good if you want to take it somewhere else. When you choose and set up your own equipment, it is usually non-proprietary, and you can take it to a different monitoring company if you want to.

10. Future Installations

Once you have installed your own alarm system, you can repeat the process and steps for any future installations you might complete. Perhaps you're setting up a security system for your office, or maybe you need one for a summer home. What you've learned from your first installation can easily apply to a second one. Take what you've learned, and put it into action!

Whether you're installing your own system for a home or business, Alarm Grid is here to help you every step of the way. We offer support online and over the phone so that you can get your system exactly the way you want it. To get started, sign-up for one of our monitoring plans with the orange button above.

If you have any questions, you can always email us at support@alarmgrid.com, you can call us during our normal business hours of 9am to 8pm EST M-F. We look forward to working with you and helping you complete your own security system installation!