Alarm Grid LYNX-EXT Posts

Hi DIYers! As you may know, testing your equipment is an integral part of owning an alarm system. But your testing should go beyond just making sure your sensors work properly and that your panel communicates with the central station. Testing your sirens and sounders is also important.

When you activate your monitoring service with Alarm Grid, there will undoubtedly be some testing involved. Our team will be checking to see if your system sends out signals successfully. This is a vital part of receiving a certificate of alarm so that you can get a discount on your homeowner's insurance. And as a DIY installer, you will be checking to make sure that all your sensors work properly. This includes things like walking through a room to see if your motion sensor notices your presence and opening and closing your doors and windows to check that your contact sensors perform correctly. But what about your sirens?

Look, we know that testing your sirens isn't the most fun. They're loud. They scare pets. They make children cry. With that in mind, it's no surprise that some users decide to disconnect their sirens during system testing. This is perfectly fine in theory. After all, your system will still be able to communicate out, and its sensors will still work properly. You might think that you can just add your sirens later after testing. However, we're here to tell you that testing your sirens and having them activate is a step that every alarm system owner should take.

But why should you test your sirens? The reason actually goes beyond the obvious answer of making sure the sounders and strobes work. It's also smart to have a good idea of exactly what your system's sirens sound like. That way if an emergency does occur, you will have a better chance of knowing immediately what is going on. Keep in mind that not all sirens are created equal. They can differ in terms of volume and pitch. By taking the time to listen to your siren, you are more likely to be ready if there ever is an emergency.

Another thing that many users don't realize is that there are usually different noises for different types of alarms. For example, an activated smoke detector will typically produce a temporal 3 sound (three consecutive tones, then a pause, repeated), while an activated carbon monoxide detector will typically produce a temporal 4 sound (four consecutive tones, plus a pause, repeated). There are also continuous tone alarms (one long, steady tone) that are commonly used for burglary and intrusion alarms. Knowing what each alarm sounds like can potentially save your life in an emergency. For example, how you respond to a break-in won't necessarily be how you respond to a fire!

At Alarm Grid, we want all our customers to be prepared when alarms occur. This includes knowing what sounds your equipment makes. If you're a monitored customer, we are happy to help you however we can. The best way to reach us is to email support@alarmgrid.com with your questions. You may also call us at (888) 818-7728 during our normal business hours of 9am to 8pm EST M-F. We look forward to helping you get the very most out of all your alarm system equipment. That includes your sirens, sounders and strobes!

We strive to have some of the best pricing on the internet for security products. When prices are reduced for us, we do our best to quickly pass off those savings to anyone who has made a purchase here.

In the last week, we have reduced the prices on over 100 items an average of 6%. Our Lyric kits have all seen price reductions between 6% and 19%.

Below is the list of all items whose price has been reduced. We hope you enjoy the savings!

One of the big gripes people have with the LYNX panels is that the only siren that it works with is the 5800WAVE. The truth is that Honeywell's wireless security system can be made to work with any wired siren. It just takes a little bit more work. We've done our best to make it simple with FAQs, manuals, and even an Alarm Grid kit, but we have been missing the most important, helpful element: videos. The following video can be viewed as a series on YouTube (if you head over there, be sure to subscribe to the Alarm Grid channel), or you can watch it in order right below.

In this first video, we show you the Alarm Grid LYNX-EXT. It's the simplest, cheapest way to get an external sounder to work with your wireless security system without having to run a wire. The LYNX-WEXT works roughly the same way as the one in the video below, however, a wire needs to be run from the relay in the WEXT to the system itself.

Putting everything together in the LYNX-EXT is really simple. Sterling goes through the wiring, and how to connect it to the wireless security system.

Sterling goes in depth about how to choose the wired sirens you would like to use, and how to do a quick power calculation on your system. In this video, we demonstrate the strongest siren we sell, the Amseco 52s, which will make a 120dB fuss if the system is breached.

Sterling gives a quick explanation about how to properly wire the siren and the strobe. Once this is done, all that is left to do is set the house ID codes in the system and the 5800RL.

Setting the House ID Codes on the LYNX Touch Units

All three of the next videos demonstrate how to set the house ID whether your system is an older, discontinued L5100, or the newer L5200 and L7000.

Setting the House ID on the 5800RL

Like most Honeywell sensors, the 5800RL uses dip switches to pick its House ID. It is the same way that the 5800WAVE works. Setting these dip switches will allow the system to communicate with the horn so that the siren can start blaring the second you need it most.

Honeywell's AD12612 is the best selling power supply in any kit. Sterling takes us through how to wire the LYNX-EXT to the power supply and external sounder. 

The Panics!

Both to show it works, as well as allowing anyone who is curious a chance to listen to the panic sounds. Below are videos of Sterling demonstrating both the Police Panic and the Fire Panic.

Although the LYNX Touch has a built-in 95dB siren it never hurts to beef up your audible output in the event of an alarm. Sirens are a great way to scare off intruders and inform any neighboring parties that an alarm event is in progress. Before the release of Alarm Grid's LYNX-EXT external siren kit, compiling the necessary parts for installing an external sounder was complicated and cumbersome. Now you can simply pick up this kit and be on your way to adding sirens to your wireless alarm system. When it comes time to install, check out the LYNX external sounder installation manual which has a detailed wiring diagram. You can also check out our FAQ: How do I add an external siren to my LYNX Touch wireless security system?

The Honeywell 5800RL wireless relay allows you to place the siren power assembly in the included Meir metal cabinet where it is most convenient and effective without any wiring runs back to the panel. The included Honeywell AD12612 auxiliary power supply has a max output of 1.2 amps which can power the brawny Amseco SSX-52S outdoor siren/strobe. You may want to just keep it simple by connecting a bullhorn style siren like the Honeywell 702 in your attic or outside the premises. There is also an included Honeywell 1361 AC transformer and an Ultratech 1240 battery backup unit which will carry low voltage DC to the power supply and keep it from losing power during outages.

Forget piecing together a kit of your own. Pick up an Alarm Grid LYNX-EXT external siren kit today and save your precious time and money!