Honeywell 5800CO Posts

We're checking out the best environmental sensors for our top security system picks for the 2020 holiday shopping season, which are the Honeywell Lyric, the Qolsys IQ Panel 2 Plus, and the 2GIG GC3e. Environmental sensors include life-safety sensors, flood sensors, and temperature sensors.

If you haven't seen our alarm panel 2020 holiday buying guide or our security sensor 2020 holiday buying guide, then be sure to go and check those out, as they will give a nice introduction to this buying guide for environmental sensors. You will need to make the same compatibility considerations for environmental sensors as you do for security sensors. The sensors you choose must be compatible with your system and communicate at a wireless frequency that is accepted by the alarm panel you are using.

As a refresher, here are the compatible sensor lineups for our recommended systems. Just like last time, the sensor lineups that are italicized and underlined represent the encrypted sensors that provide extra wireless security and protection.

• Honeywell Lyric - Honeywell SiX Series, Honeywell 5800 Series, 2GIG 345 MHz Series
• 2GIG GC3e - 2GIG eSeries Encrypted Sensors, 2GIG 345 MHz Series, Honeywell 5800 Series
• Qolsys IQ Panel 2 Plus 319.5 MHz - DSC PowerG Sensors, Qolsys S-Line Sensors, Qolsys Legacy 319.5 MHz Sensors, Legacy Interlogix Sensors, Legacy GE Sensors
• Qolsys IQ Panel 2 Plus 345 MHz - DSC PowerG Sensors, Honeywell 5800 Sensors, 2GIG 345 MHz Sensors
• Qolsys IQ Panel 2 Plus 433 MHz - DSC PowerG Sensors, Legacy DSC 433 MHZ Sensors

While security sensors look for signs of forced entry and unauthorized access, environmental sensors look for undesirable environmental conditions. Specifically, we offer environmental sensors that look for life-threatening conditions, such as a fire or the presence of carbon monoxide (CO) gas. We also offer environmental sensors for detecting floods, water leaks, and unusually high or low temperatures that indicate a broken HVAC system. We will cover each type of environmental sensor in greater detail later in this holiday buying guide.

Adding environmental sensors to your system offers a few advantages. For one, it makes your alarm system more versatile so that it is looking for more than just security breaches. You will also be able to check off more boxes on your certificate of alarm (CoA), and that could lead to bigger savings on your home owner's insurance. Make sure to check with your insurance company to see if that is the case.

Life-Safety Sensors

Life-safety sensors monitor for unsafe environmental conditions that could result in a loss of life. Specifically, this group is primarily comprised of smoke and heat detectors and carbon monoxide sensors. There are also special combination sensors and listening modules that we will discuss further down the line.

First, we will take a look at some of our most popular smoke and heat detectors. These sensors monitor for both the smoke and extremely high temperatures associated with a fire. It is recommended that you have at least one (1) of these sensors on each floor of your building, particularly inside of sleeping areas and in central and connecting areas such as living rooms and hallways.

When checking out these sensors, you might also look for one-go-all-go functionality. This means that when one detector on the network activates, all of the other compatible sensors on the network will also activate their sounders. This can be very important for ensuring that everyone is alerted to the emergency. Certain jurisdictions may require one-go-all-go as part of building codes, so check with your local fire marshal to see if that is the case.

Here are our top picks for smoke and heat detectors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Honeywell SiXSMOKE	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	Encrypted photoelectric smoke detector and 135°F fixed temperature and 15°F per minute rate-of-rise heat detector w/ 85 dB sounder. Supports One-Go-All-Go.
DSC PG9936	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector w/ 85 dB sounder. Supports One-Go-All-Go.
2GIG SMKT8e-345	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries encryption	Encrypted photoelectric smoke detector and 15°F per minute rate-of-rise heat detector when fixed temperature is 104°F or higher w/ 90 dB sounder and freeze detection at 40°F.
Honeywell 5808W3	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Non-encrypted photoelectric smoke detector and 135°F fixed temperature heat detector w/ 85 dB sounder and freeze detection at 41°F.

Now let's look at carbon monoxide sensors. These devices respond upon detecting unusually high levels of carbon monoxide (CO) gas. This gas is both odorless and tasteless, making it virtually impossible to detect without a proper sensor. The gas is extremely harmful to humans, and it can result in serious injury or death in a matter of minutes. We recommend installing at least one CO detector on each floor of your home or office. They are often installed outside of garages and furnace rooms where CO events are most likely to occur.

Here are our top picks for carbon monoxide sensors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
DSC PG9933	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG CO Detector w/ 85 dB sounder.
2GIG CO8e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries encryption	2GIG eSeries CO Detector w/ 85 dB sounder.
Honeywell 5800CO	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Honeywell 5800 Series CO Detector w/ 85 dB sounder.
2GIG CO8	2GIG 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	2GIG CO Detector w/ 85 dB sounder.
Qolsys IQ Carbon	Qolsys 319.5 MHz Series	319.5 MHz IQ Panel 2 Plus	300 Nominal Feet	None	Qolsys CO Detector w/ 85 dB sounder.

We also want to give some special recognition to some combination smoke and CO detectors from Honeywell. These sensors combine fire detection with carbon monoxide detection into one convenient life-safety device.

Here are our top picks for combination smoke and CO detectors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Honeywell SiXCOMBO	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector and CO detector w/ 85 dB sounder. Supports One-Go-All-Go.
Honeywell 5800COMBO	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector and CO detector w/ 85 dB sounder and freeze detection at 41°F.

Lastly, we want to mention a pair of listening modules. These devices actively listen for the Temporal 3 (T3) sound of an activated smoke detector or the Temporal 4 (T4) sound of an activated carbon monoxide sensor. These are commonly used with wired smoke detectors and CO detectors that would otherwise have no way of interfacing with an alarm system. If your smoke detectors or CO detectors are one-go-all-go, then, a single listening module can take over your entire wired detector network.

Here are our top picks for smoke & CO listening modules.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Encore FireFighter FF345	Encore 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Offers both T3 Detection for Fire & T4 Detection for CO
Interlogix SLX-AD-T3	Legacy Interlogix 319.5 MHz	319.5 MHz IQ Panel 2 Plus	200 Nominal Feet	None	Only offers T3 Detection for Fire. Not for use with CO detectors.

Flood Sensors

Next, we'll be looking at flood sensors. These devices use probes to detect water caused by a flood or leak. It only takes a small amount of liquid to activate one of these sensors, so your system will be alerted before any serious damage occurs. Many of these sensors double as temperature sensors, so expect to see quite a bit of cross-over with that section as well. For best results, use your flood sensors in low-plane areas where leaks are likely to occur, such as underneath toilets, water heaters, and in basements. You might also see that some flood sensor have a reporting delay that is used for false alarm prevention. This will be listed in the notes section in the table when applicable.

Let's check out our top picks for flood sensors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
DSC PG9985	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG Flood Sensor w/ 6-Foot Detection Probe.
2GIG FT6e-345	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	2GIG eSeries Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.
Qolsys IQ Flood-S	Qolsys S-Line Series	319.5 MHz IQ Panel 2 Plus	600 Nominal Feet	Qolsys S-Line Encryption	Qolsys S-Line Flood Sensor w/ 6-Foot Detection Probe. Has a 1 to 3 minute reporting delay.
Honeywell 5800FLOOD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Honeywell 5800 Series Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 45°F. Has a 25 second reporting delay.
2GIG FT6-345	2GIG 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	2GIG 345 MHz Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.

Temperature Sensors

The final type of environmental sensors we'll be checking out are temperature sensors. These sensors look for unusually high or low temperatures that indicate a broken HVAC system. When a temperature sensor is used for high-temperature detection, it should not be confused with a heat detector that looks for extreme temperatures only associated with fires. Instead, the high-end for a temperature sensor will usually activate at around 90°F. When a temperature sensor is used for low-temperature detection, it will sometimes be referred to as a freeze sensor. On the low-end, a freeze sensor will typically activate at a slightly higher than the temperature at which water freezes, which is 32°F. This is done to give the end user a bit of notice so that they can take action before the pipes freeze. You can typically expect a freeze sensor to activate between 40°F and 45°F. Most temperature sensors will offer both high and low temperature detection. And just like in the previous category, there is a lot of crossover with flood sensors, so you may see some repeats from the previous selection.

Here are our top picks for temperature sensors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
DSC PG9905	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG Temperature Sensor w/ customizable high and low temperature detection.
2GIG FT6e-345	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	2GIG eSeries Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.
Qolsys IQ Temp-S	Qolsys S-Line Series	319.5 MHz IQ Panel 2 Plus	600 Nominal Feet	Qolsys S-Line Encryption	Qolsys S-Line Temperature Sensor w/ High Temperature Detection @ 100°F and Low Temperature Detection at 40°F.
Honeywell 5800FLOOD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Honeywell 5800 Series Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 45°F. Has a reporting delay of 25 seconds.
2GIG FT6-345	2GIG 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	2GIG 345 MHz Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.

Contact Us

Remember to contact us if you have any questions about environmental sensors or their compatibility. The best way to reach us is to email support@alarmgrid.com. This is also a good email to use if you are interested in starting new monitoring service. Remember that we are available to check email from 9am to 8pm ET M-F. We look forward to hearing from you!

A great way to build out your Honeywell Lyric is with Honeywell 5800 Sensors. These are simple, 345 MHz wireless sensors that you can easily enroll with the system for security, life-safety, and environmental monitoring. They are perfect for expanding your system and making it more robust.

When you want to pair a Honeywell 5800 Sensor with the Lyric, the process is very straightforward. Put the Lyric in its auto-enrollment mode by choosing Security > Tools > enter Installer Code (default 4112) > Program > Zones > Add New > Serial Number. Make sure the RF Type on the right-hand side is set to 5800. Then activate the sensor either by faulting it or triggering its cover tamper switch. The Lyric should beep to confirm that it received a signal transmission. Then activate the sensor a second time to have the Lyric display the Serial Number. The third activation will confirm the Serial Number and return you to the screen where you can configure the zone settings.

Programming the zone settings for the sensor is actually quite simple. Depending on how you enrolled the sensor, you may need to adjust the Loop Number. This is almost always the case if you enrolled the sensor by activating its tamper switch. Refer to the instruction manual for the 5800 Sensor to determine which Loop Number to use.

The two (2) Zone Descriptors and the Device Type serve as the name for the sensor. You should choose a name that will help you identify the sensor, e.g. "Front Bedroom Motion Sensor", "South Hallway Door", etc. The Response Type determines how the system responds when the sensor is faulted. See our list of Lyric Response Types for more info.

Alarm Report should be set to Yes if you want the system to report out through AlarmNet to a Central Station if the zone causes an alarm on the system. That is an essential component of alarm monitoring services. Chime is optional, and it has the panel emit any one of several available sounds when the zone is faulted. Supervision tells the panel to look for an RF check-in signal from the sensor periodically to ensure that it is online. Click Save in the bottom-right after you finish adjusting the settings.

Keep in mind that only uni-directional (one-way) sensors from the Honeywell 5800 Series can be used with the Lyric. This leaves out bi-directional devices like the Honeywell 5800WAVE Siren, the Honeywell 5828 Keypad, and the Honeywell 5800RL Relay Module, so make sure you do not buy those for the Lyric. But you still have a lot of excellent sensors and security devices to choose from.

Below is a list of the Honeywell 5800 Sensors that you can use with the Honeywell Lyric:

Sensor Name	Notes
Honeywell 5800MINI	Door/Window sensor. Uses Loop 1.
Honeywell 5800PIR-RES	PIR motion sensor. Uses Loop 1. Coverage Area: 35' x 40'
Honeywell 5816	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5811	Door and window sensor. Uses Loop 1.
Honeywell 5800C2W	9-zone wired to wireless converter. Allows hardwired sensors to communicate with the Lyric as wireless devices. All zones use Loop 1 and a unique Serial Number ID.
Honeywell 5800CO	Carbon monoxide sensor. Loop 1 = CO Detection Loop 2 = End of Sensor Life (separate programming only required on TURBO and other V-Plex panels)
Honeywell 5800COMBO	Combination, smoke, heat, CO, and low-temperature sensor. Uses up to five (5) zones on the Lyric Panel. Has two (2) Serial Numbers for enrollment purposes. Loop 1, SN 1 = Smoke/Heat Detection Loop 2, SN 1 = Smoke/Heat Maintenance Loop 3, SN 1 = Low Temperature Detection Loop 1, SN 2 = CO Detection Loop 2, SN 2 = End of Sensor Life (separate programming required only on TURBO and other V-Plex panels)
Honeywell 5800FLOOD	Flood and temperature sensor. Loop 1 = Low Temperature Detection Loop 2 = High Temperature Detection Loop 3 = Flood Detection
Honeywell 5800MICRA	Recessed window sensor. Uses Loop 1.
Honeywell 5800PIR	PIR motion sensor. Loop 1 = Low Sensitivity Motion. Loop 2 = High Sensitivity Motion. Loop 3 = Low Temperature Detection Coverage Area: 35' x 40'
Honeywell 5800PIR-COM	Commercial PIR motion sensor. Loop 1 = Low Sensitivity Motion Loop 2 = High Sensitivity Motion Loop 3 = Low Temperature Detection Coverage Area: 60' x 80'
Honeywell 5800PIR-OD	Outdoor PIR motion sensor. Uses Loop 1.
Honeywell 5800PIR-OD2	Outdoor PIR motion sensor. Uses Loop 1.
Honeywell 5800RP	Wireless repeater for Honeywell 5800 Sensors. Does not require enrollment, but can be assigned a single zone for RF supervision, low-battery, AC loss, and RF jam detection. This is done using Serial Number 1 with Loop 1, with DIP Switch 2 set in the OFF position. Can also use up to four (4) separate zones for supervision when DIP Switch 2 is set to ON. This is required for UL installations.
Honeywell 5800RPS	Recessed door/window sensor. Uses Loop 1.
Honeywell 5800SS1	Shock sensor. Uses Loop 1.
Honeywell 5802MN	Medical alert button. Uses Loop 1.
Honeywell 5802MN2	Medical alert button. Uses Loop 1.
Honeywell 5802WXT	Panic button. Uses Loop 1.
Honeywell 5802WXT-2	Panic button. Uses Loop 1.
Honeywell 5806W3	Smoke detector. Uses Loop 1.
Honeywell 5808W3	Smoke and heat detector. Loop 1 = Smoke & Heat Detection Loop 3 = Low Temperature Detection
Honeywell 5809	Fixed temperature and rate-of-rise heat detector. Uses Loop 1. Alarm occurs when the temperature exceeds 135 degrees Fahrenheit, or when the temperature rises more than 15 degrees Fahrenheit per minute.
Honeywell 5809FXT	Fixed temperature heat detector. Uses Loop 1. Alarm occurs when the temperature exceeds 135 degrees Fahrenheit.
Honeywell 5809SS	Fixed temperature and rate-of-rise heat detector. Uses Loop 1. Alarm occurs at 135 degrees Fahrenheit or when the temperature rises more than 15 degrees Fahrenheit per minute.
Honeywell 5814	Door and window sensor. Uses Loop 1.
Honeywell 5815	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5816MN	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switches
Honeywell 5816OD	Outdoor door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5817	Three (3) zone door and window sensor & transmitter. Loop 1 = NC or NO (DIP Switch Selectable) unsupervised. It does not use an End of Line Resistor (EOLR) Loop 2, 3 = NC Only. Both are unsupervised with no EOLR used
Honeywell 5817CBXT	Three (3) zone commercial transmitter. Loop 1 = Two (2) Terminals; Primary Loop supervised by 470k Ohm (yellow, purple, yellow, gold) EOLR. Resistor must ALWAYS be installed, even if Loop 1 is not programmed. If Loop 1 is used as a burglary zone, then Loop 4 must be programmed as a separate zone for Cover Tamper protection. Loop 2 = NC Reed Switch Loop 3 = Two (2) Terminals; NC Loop unsupervised, no EOLR required
Honeywell 5817XT	Three (3) zone door and window sensor & transmitter. Loop 1 = NC or NO (DIP Switch Selectable) unsupervised with no EOLR required Loop 2, 3 = Two (2) Terminal Blocks, NC Only
Honeywell 5818MNL	Recessed door and window sensor. Uses Loop 1. Not suitable for use in metal doors
Honeywell 5819	Three (3) zone shock processor. Loop 1 = NC for Inertia Style External Shock Sensor. This input provides a suitable fast loop response of from 1ms to 20ms, based on dip switch setting Loop 2 = Reed Switch Loop 3 = NC for Wired Contact, unsupervised with no EOLR required
Honeywell 5819S	Shock sensor and contact sensor. Loop 1 = Built-in Inertia Style Shock Sensor Loop 2 = Reed Switch Loop 3 = NC for Wired Contact
Honeywell 5819WHS	Three (3) zone shock processor. Loop 1 = NC, Built-in Inertia Style Shock Sensor Loop 2 = Reed Switch Loop 3 = NC for Wired Contact
Honeywell 5820L	Slimline door and window sensor. Uses Loop 1.
Honeywell 5822T	Garage tilt sensor. Loop 1 = NC for Wired Contact, unsupervised, no EOLR used Loop 3 = Tilt Switch
Honeywell 5834-2	Two (2) button key fob. Dual-button inputs allowed. Uses three (3) loops total, for a possible three (3) inputs. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5834-4	Four (4) button key fob. Dual-button inputs allowed. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5834-4EN	Four (4) button key fob. Dual-button inputs allowed. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5853	Glass break sensor. Uses Loop 1.
Honeywell 5869	Commercial panic switch. Uses Loop 1. Latches when tripped, key (provided) needed to reset it after it is tripped
Honeywell 5878	Six (6) button key fob. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible.
Honeywell 5898	Dual-tec motion sensor. Loop 1 = Low Sensitivity Motion Sensor. Pet immunity is available for this loop. 50lb or 100lb pet immunity, selectable via DIP Switch 1 Loop 2 = High Sensitivity Motion Sensor. Loop 3 = Temperature Sensor (High or Low, DIP Switch Selectable)

With a new year comes reduced pricing on many of our great existing products. We have just dropped the prices on 73 of our existing offerings. You can certainly find something great to upgrade your existing system or use with a new installation. Let's check out these awesome products!

Before we go through and list each and every reduced price product, we figured we'd go through and talk about some of the ones that excite us the most. After all, sorting through a list of 73 products is pretty daunting. Our initial "best-of" list may help you find exactly what you're looking for. These products are great if you have an existing system, or if you are building a new system and want to add some cool accessories.

These products are presented in alphabetical order:

Alarm.com ADC-V723 Outdoor Camera

The ADC-V723 is the current flagship outdoor security camera for use with the Alarm.com platform. This simple, yet powerful camera makes the perfect addition to any home or small business. It can capture video at up to 1080p quality, and it makes use of High Dynamic Range (HDR) to improve image depth and luminosity.

Alarm.com T2000 Smart Z-Wave Thermostat

If you are still looking for a smart Z-Wave thermostat, then the ADC-T2000 is an outstanding entry-level option. It conveniently wires in place of your existing thermostat to give you smart control over your HVAC system. It can pair nicely with both the Alarm.com and Total Connect 2.0 platforms. You just need a compatible Z-Wave hub to get started.

DSC PG9312 Outdoor Door/Window Sensor

The DSC PG9312 is the premier outdoor contact sensor for any user with a PowerG-compatible security system. It offers a maximum magnet spacing gap of 1.75", which gives you more flexibility in choosing a location for the sensor and magnet. Like all PowerG Sensors, it offers a wireless range of up to 2 km away from the panel, as well as 128-bit AES encryption.

DSC PG9914 Motion Sensor

Anyone with a PowerG Security System looking to add a basic indoor motion sensor should turn to the DSC PG9914. This is a simple, yet effective motion sensor that is great for use in nearly any home or business. It offers a modest coverage area of 39 feet, and the sensor provides pet immunity for small animals weighing up to 85 lbs.

Encore FireFighter FF345 Smoke/CO Listening Module

The Encore FireFighter FF345 is perfect if you have existing high-voltage smoke detectors that you want to integrate into a 345 MHz wireless system. The module can detect both the Temporal 3 sound of an activated smoke detector and the Temporal 4 sound of an activated CO detector. And if your high-voltage devices are one-go-all-go, then a single FF345 can takeover your entire network.

Honeywell 5822T Garage Door Tilt Sensor

Also for 345 MHz system users, the Honeywell 5822T allows your system to monitor your garage door to see if it's opened or closed. This wireless sensor works great for security and automation purposes alike. You might even create a special smart scene that activates as soon as the 5822T detects that you garage door has been opened!

Honeywell IPCAM-WIC1 Indoor Camera

The Honeywell IPCAM-WIC1 Indoor Camera is for anyone with an existing Total Connect 2.0 Video Monitoring service plan that they want to expand upon. This is a simple and straightforward camera that captures video at up to 720p quality. It can be easily rested on a desk or table, and no hard-mounting is required.

Qolsys IQ DW MINI-S Door/Window Sensor

The Qolsys IQ DW MINI-S can be used by anyone with a 319.5 MHz wireless system, including the Qolsys IQ Panel 2 Plus w/ Legacy Interlogix & Qolsys Daughtercard. This is a straightforward door and window contact sensor that makes a nice addition to any compatible system. Its small and compact design allows for a tidy installation.

Please see our complete list of reduced price products in the table below, organized by product type:

If you have any questions about these products or any of the other products on our site, including product compatibilities, please reach out to us. You may also contact us if you want to learn more about our monitoring services. The best way to reach us is to email support@alarmgrid.com. Or you may call us at (888) 818-7728. Remember that our support hours run from 9am to 8pm ET M-F. We look forward to helping you find the perfect product for your needs!

Actress Anna Faris, known for her comedic roles, suffered from a not-so-funny incident over the recent Thanksgiving Holiday. The actress and 12 members of her family were the victims of a carbon monoxide (CO) gas incident. The incident occurred in a North Lake Tahoe cabin they were renting.

A representative from the North Tahoe Fire Protection District stated that the vacation cabin had carbon monoxide levels as high as 55 parts per million (ppm). Long-term indoor exposure should be no higher than 15 ppm. The structure did not have any carbon monoxide sensors installed to indicate such danger. Nevada state law requires CO alarms in all family dwellings.

Thankfully, Anna Faris and her family are okay following the incident. However, two of her family members visited the local emergency room. Doctors diagnosed them with CO poisoning, and they were perfectly fine after receiving some care. Firefighters from the North Tahoe FD immediately rushed to the cabin and saved Ms. Faris and her accompanying family shortly thereafter.

According to North Lake Tahoe Fire Official Erin Holland, the CO levels indicated inside the building would have caused a "fatality in a short period of time" had the rescue team not intervened. Faris made sure to send her sincere gratitude to the North Tahoe FD following the incident.

We have spoken about the dangers of carbon monoxide gas many times on the Alarm Grid blog. The odorless and tasteless gas kills hundreds of people every year in the United States. If it weren't for the quick work of local firefighters, a talented actress and her family may have fallen victim as well. They are lucky to be alive, and the rescue team deserves praise for the fact that any exposure was kept as minimal as possible.

As you know by now, it is crucial to have carbon monoxide sensors installed in your home. Ideally, you should have CO detectors enrolled with your security system. By pairing these devices with a system that has active monitoring service, you and/or a central station can receive alerts regarding any of your CO sensors that activate while you are away.

If your home has hardwired high-voltage CO sensors (as is required in most jurisdictions), you can indirectly integrate these devices with your alarm system using a wireless takeover listening module. We offer variants for 345 MHz, and 433 MHz wireless alarm systems. And if you don't have hardwired CO detectors in your home, then we sell plenty of standalone units that pair directly with alarm panels like any other sensor.

When traveling, make sure that all on-site CO sensors and smoke detectors are working properly. If you have any doubts, ask the building operators to perform a test. This is a reasonable request that any property manager should be able to accommodate. Please note that we ARE NOT suggesting that you bring canned CO gas or canned smoke on an airplane for testing purposes. That could get you into a lot of trouble. Make arrangements for on-site testing, without bringing your own supplies.

It may also be a good idea to buy a cheap conventional battery-operated carbon monoxide sensor when you get to your vacation site. It may turn out that the place you visit does not have CO detectors. This was the case with Anna Faris and her family. We do not sell standalone battery-operated CO detectors on our website. But you can get most models between $10 and $20 from most department and hardware stores. Some models will even show you the detected parts per million for CO gas! If you are staying in a larger property, you may want to obtain multiple sensors.

Remember that our goal at Alarm Grid is to keep you and your loved ones safe. If you ever need help choosing a carbon monoxide sensor for your system, or if you would like to learn more about how we can monitor your home, please email us at support@alarmgrid.com. You are also invited to call us at (888) 818-7728 during our usual business hours of 9am to 8pm ET M-F. We look forward to hearing from you!