Honeywell 5800FLOOD Posts

Resideo announced last week that due to a required component becoming obsolete, they are forced to discontinue the popular 5800FLOOD sensor. There is still some available stock, so Alarm Grid has not yet discontinued it, but once all stock has been exhausted, the 5800FLOOD is gone for good.

The 5800FLOOD is popular because unlike the 5821, it doesn't require that a water probe be added to the sensor. Water detection is built-in, and configuration is easy. Another benefit of the 5800FLOOD is that it will alert for flooding more quickly than the 5821. The prongs of the 5800FLOOD need only be in contact with water for about 25 seconds before a signal is sent to the alarm panel. The 5821 flood probe must be in contact with water for about three (3) minutes before sending a signal.

In addition to flood sensing, the 5800FLOOD also monitors for extreme cold and/or hot temperatures locally. This is done using a temperature sensor that is built into the 5800FLOOD. For cold temperature sensing, if the ambient temperature drops below 45℉ (7.2℃) for more than 15 minutes, an alert is sent using Loop 1. For high-temperature sensing, if the temperature rises above 95℉ (35℃) for more than 15 minutes, then an alert is sent using Loop 2. The flood sensor transmits using Loop 3.

Now that the 5800FLOOD is being discontinued, the Resideo and Honeywell Home 5821 is the recommended replacement. One drawback to the 5821 is that it requires a remote probe be added for flood sensing, and for freeze sensing. However, only one (1) remote probe can be used per transmitter, so if you need to monitor for both flood and freeze, two (2) 5821s are required.

The 5821 supports the following functions:

For flood sensing, we recommend using the FP280 as it includes wiring, and the required resistor is already in place. With the 470PB, the user is responsible for providing their own wire and must add the 2.2 MΩ resistor themselves. In all cases, wiring between the 5821 and whichever remote probe is used should be made as short as possible, and should not exceed 96" (243cm). Be sure to read the full Install Guide for the 5821 for all of its various quirks.

Supply chain shortages claim another victim in the 5800FLOOD. It seems like only yesterday that we were excitedly telling you about it. What are your thoughts on the demise of this "New and Improved" environmental sensor? Leave us a note in the comments, as we always love hearing from our readers.

We're checking out the best environmental sensors for our top security system picks for the 2020 holiday shopping season, which are the Honeywell Lyric, the Qolsys IQ Panel 2 Plus, and the 2GIG GC3e. Environmental sensors include life-safety sensors, flood sensors, and temperature sensors.

If you haven't seen our alarm panel 2020 holiday buying guide or our security sensor 2020 holiday buying guide, then be sure to go and check those out, as they will give a nice introduction to this buying guide for environmental sensors. You will need to make the same compatibility considerations for environmental sensors as you do for security sensors. The sensors you choose must be compatible with your system and communicate at a wireless frequency that is accepted by the alarm panel you are using.

As a refresher, here are the compatible sensor lineups for our recommended systems. Just like last time, the sensor lineups that are italicized and underlined represent the encrypted sensors that provide extra wireless security and protection.

• Honeywell Lyric - Honeywell SiX Series, Honeywell 5800 Series, 2GIG 345 MHz Series
• 2GIG GC3e - 2GIG eSeries Encrypted Sensors, 2GIG 345 MHz Series, Honeywell 5800 Series
• Qolsys IQ Panel 2 Plus 319.5 MHz - DSC PowerG Sensors, Qolsys S-Line Sensors, Qolsys Legacy 319.5 MHz Sensors, Legacy Interlogix Sensors, Legacy GE Sensors
• Qolsys IQ Panel 2 Plus 345 MHz - DSC PowerG Sensors, Honeywell 5800 Sensors, 2GIG 345 MHz Sensors
• Qolsys IQ Panel 2 Plus 433 MHz - DSC PowerG Sensors, Legacy DSC 433 MHZ Sensors

While security sensors look for signs of forced entry and unauthorized access, environmental sensors look for undesirable environmental conditions. Specifically, we offer environmental sensors that look for life-threatening conditions, such as a fire or the presence of carbon monoxide (CO) gas. We also offer environmental sensors for detecting floods, water leaks, and unusually high or low temperatures that indicate a broken HVAC system. We will cover each type of environmental sensor in greater detail later in this holiday buying guide.

Adding environmental sensors to your system offers a few advantages. For one, it makes your alarm system more versatile so that it is looking for more than just security breaches. You will also be able to check off more boxes on your certificate of alarm (CoA), and that could lead to bigger savings on your home owner's insurance. Make sure to check with your insurance company to see if that is the case.

Life-Safety Sensors

Life-safety sensors monitor for unsafe environmental conditions that could result in a loss of life. Specifically, this group is primarily comprised of smoke and heat detectors and carbon monoxide sensors. There are also special combination sensors and listening modules that we will discuss further down the line.

First, we will take a look at some of our most popular smoke and heat detectors. These sensors monitor for both the smoke and extremely high temperatures associated with a fire. It is recommended that you have at least one (1) of these sensors on each floor of your building, particularly inside of sleeping areas and in central and connecting areas such as living rooms and hallways.

When checking out these sensors, you might also look for one-go-all-go functionality. This means that when one detector on the network activates, all of the other compatible sensors on the network will also activate their sounders. This can be very important for ensuring that everyone is alerted to the emergency. Certain jurisdictions may require one-go-all-go as part of building codes, so check with your local fire marshal to see if that is the case.

Here are our top picks for smoke and heat detectors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Honeywell SiXSMOKE	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	Encrypted photoelectric smoke detector and 135°F fixed temperature and 15°F per minute rate-of-rise heat detector w/ 85 dB sounder. Supports One-Go-All-Go.
DSC PG9936	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector w/ 85 dB sounder. Supports One-Go-All-Go.
2GIG SMKT8e-345	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries encryption	Encrypted photoelectric smoke detector and 15°F per minute rate-of-rise heat detector when fixed temperature is 104°F or higher w/ 90 dB sounder and freeze detection at 40°F.
Honeywell 5808W3	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Non-encrypted photoelectric smoke detector and 135°F fixed temperature heat detector w/ 85 dB sounder and freeze detection at 41°F.

Now let's look at carbon monoxide sensors. These devices respond upon detecting unusually high levels of carbon monoxide (CO) gas. This gas is both odorless and tasteless, making it virtually impossible to detect without a proper sensor. The gas is extremely harmful to humans, and it can result in serious injury or death in a matter of minutes. We recommend installing at least one CO detector on each floor of your home or office. They are often installed outside of garages and furnace rooms where CO events are most likely to occur.

Here are our top picks for carbon monoxide sensors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
DSC PG9933	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG CO Detector w/ 85 dB sounder.
2GIG CO8e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries encryption	2GIG eSeries CO Detector w/ 85 dB sounder.
Honeywell 5800CO	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Honeywell 5800 Series CO Detector w/ 85 dB sounder.
2GIG CO8	2GIG 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	2GIG CO Detector w/ 85 dB sounder.
Qolsys IQ Carbon	Qolsys 319.5 MHz Series	319.5 MHz IQ Panel 2 Plus	300 Nominal Feet	None	Qolsys CO Detector w/ 85 dB sounder.

We also want to give some special recognition to some combination smoke and CO detectors from Honeywell. These sensors combine fire detection with carbon monoxide detection into one convenient life-safety device.

Here are our top picks for combination smoke and CO detectors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Honeywell SiXCOMBO	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector and CO detector w/ 85 dB sounder. Supports One-Go-All-Go.
Honeywell 5800COMBO	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector and CO detector w/ 85 dB sounder and freeze detection at 41°F.

Lastly, we want to mention a pair of listening modules. These devices actively listen for the Temporal 3 (T3) sound of an activated smoke detector or the Temporal 4 (T4) sound of an activated carbon monoxide sensor. These are commonly used with wired smoke detectors and CO detectors that would otherwise have no way of interfacing with an alarm system. If your smoke detectors or CO detectors are one-go-all-go, then, a single listening module can take over your entire wired detector network.

Here are our top picks for smoke & CO listening modules.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Encore FireFighter FF345	Encore 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Offers both T3 Detection for Fire & T4 Detection for CO
Interlogix SLX-AD-T3	Legacy Interlogix 319.5 MHz	319.5 MHz IQ Panel 2 Plus	200 Nominal Feet	None	Only offers T3 Detection for Fire. Not for use with CO detectors.

Flood Sensors

Next, we'll be looking at flood sensors. These devices use probes to detect water caused by a flood or leak. It only takes a small amount of liquid to activate one of these sensors, so your system will be alerted before any serious damage occurs. Many of these sensors double as temperature sensors, so expect to see quite a bit of cross-over with that section as well. For best results, use your flood sensors in low-plane areas where leaks are likely to occur, such as underneath toilets, water heaters, and in basements. You might also see that some flood sensor have a reporting delay that is used for false alarm prevention. This will be listed in the notes section in the table when applicable.

Let's check out our top picks for flood sensors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
DSC PG9985	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG Flood Sensor w/ 6-Foot Detection Probe.
2GIG FT6e-345	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	2GIG eSeries Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.
Qolsys IQ Flood-S	Qolsys S-Line Series	319.5 MHz IQ Panel 2 Plus	600 Nominal Feet	Qolsys S-Line Encryption	Qolsys S-Line Flood Sensor w/ 6-Foot Detection Probe. Has a 1 to 3 minute reporting delay.
Honeywell 5800FLOOD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Honeywell 5800 Series Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 45°F. Has a 25 second reporting delay.
2GIG FT6-345	2GIG 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	2GIG 345 MHz Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.

Temperature Sensors

The final type of environmental sensors we'll be checking out are temperature sensors. These sensors look for unusually high or low temperatures that indicate a broken HVAC system. When a temperature sensor is used for high-temperature detection, it should not be confused with a heat detector that looks for extreme temperatures only associated with fires. Instead, the high-end for a temperature sensor will usually activate at around 90°F. When a temperature sensor is used for low-temperature detection, it will sometimes be referred to as a freeze sensor. On the low-end, a freeze sensor will typically activate at a slightly higher than the temperature at which water freezes, which is 32°F. This is done to give the end user a bit of notice so that they can take action before the pipes freeze. You can typically expect a freeze sensor to activate between 40°F and 45°F. Most temperature sensors will offer both high and low temperature detection. And just like in the previous category, there is a lot of crossover with flood sensors, so you may see some repeats from the previous selection.

Here are our top picks for temperature sensors.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
DSC PG9905	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG Temperature Sensor w/ customizable high and low temperature detection.
2GIG FT6e-345	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	2GIG eSeries Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.
Qolsys IQ Temp-S	Qolsys S-Line Series	319.5 MHz IQ Panel 2 Plus	600 Nominal Feet	Qolsys S-Line Encryption	Qolsys S-Line Temperature Sensor w/ High Temperature Detection @ 100°F and Low Temperature Detection at 40°F.
Honeywell 5800FLOOD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Honeywell 5800 Series Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 45°F. Has a reporting delay of 25 seconds.
2GIG FT6-345	2GIG 345 MHz Series	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	2GIG 345 MHz Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.

Contact Us

Remember to contact us if you have any questions about environmental sensors or their compatibility. The best way to reach us is to email support@alarmgrid.com. This is also a good email to use if you are interested in starting new monitoring service. Remember that we are available to check email from 9am to 8pm ET M-F. We look forward to hearing from you!

A great way to build out your Honeywell Lyric is with Honeywell 5800 Sensors. These are simple, 345 MHz wireless sensors that you can easily enroll with the system for security, life-safety, and environmental monitoring. They are perfect for expanding your system and making it more robust.

When you want to pair a Honeywell 5800 Sensor with the Lyric, the process is very straightforward. Put the Lyric in its auto-enrollment mode by choosing Security > Tools > enter Installer Code (default 4112) > Program > Zones > Add New > Serial Number. Make sure the RF Type on the right-hand side is set to 5800. Then activate the sensor either by faulting it or triggering its cover tamper switch. The Lyric should beep to confirm that it received a signal transmission. Then activate the sensor a second time to have the Lyric display the Serial Number. The third activation will confirm the Serial Number and return you to the screen where you can configure the zone settings.

Programming the zone settings for the sensor is actually quite simple. Depending on how you enrolled the sensor, you may need to adjust the Loop Number. This is almost always the case if you enrolled the sensor by activating its tamper switch. Refer to the instruction manual for the 5800 Sensor to determine which Loop Number to use.

The two (2) Zone Descriptors and the Device Type serve as the name for the sensor. You should choose a name that will help you identify the sensor, e.g. "Front Bedroom Motion Sensor", "South Hallway Door", etc. The Response Type determines how the system responds when the sensor is faulted. See our list of Lyric Response Types for more info.

Alarm Report should be set to Yes if you want the system to report out through AlarmNet to a Central Station if the zone causes an alarm on the system. That is an essential component of alarm monitoring services. Chime is optional, and it has the panel emit any one of several available sounds when the zone is faulted. Supervision tells the panel to look for an RF check-in signal from the sensor periodically to ensure that it is online. Click Save in the bottom-right after you finish adjusting the settings.

Keep in mind that only uni-directional (one-way) sensors from the Honeywell 5800 Series can be used with the Lyric. This leaves out bi-directional devices like the Honeywell 5800WAVE Siren, the Honeywell 5828 Keypad, and the Honeywell 5800RL Relay Module, so make sure you do not buy those for the Lyric. But you still have a lot of excellent sensors and security devices to choose from.

Below is a list of the Honeywell 5800 Sensors that you can use with the Honeywell Lyric:

Sensor Name	Notes
Honeywell 5800MINI	Door/Window sensor. Uses Loop 1.
Honeywell 5800PIR-RES	PIR motion sensor. Uses Loop 1. Coverage Area: 35' x 40'
Honeywell 5816	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5811	Door and window sensor. Uses Loop 1.
Honeywell 5800C2W	9-zone wired to wireless converter. Allows hardwired sensors to communicate with the Lyric as wireless devices. All zones use Loop 1 and a unique Serial Number ID.
Honeywell 5800CO	Carbon monoxide sensor. Loop 1 = CO Detection Loop 2 = End of Sensor Life (separate programming only required on TURBO and other V-Plex panels)
Honeywell 5800COMBO	Combination, smoke, heat, CO, and low-temperature sensor. Uses up to five (5) zones on the Lyric Panel. Has two (2) Serial Numbers for enrollment purposes. Loop 1, SN 1 = Smoke/Heat Detection Loop 2, SN 1 = Smoke/Heat Maintenance Loop 3, SN 1 = Low Temperature Detection Loop 1, SN 2 = CO Detection Loop 2, SN 2 = End of Sensor Life (separate programming required only on TURBO and other V-Plex panels)
Honeywell 5800FLOOD	Flood and temperature sensor. Loop 1 = Low Temperature Detection Loop 2 = High Temperature Detection Loop 3 = Flood Detection
Honeywell 5800MICRA	Recessed window sensor. Uses Loop 1.
Honeywell 5800PIR	PIR motion sensor. Loop 1 = Low Sensitivity Motion. Loop 2 = High Sensitivity Motion. Loop 3 = Low Temperature Detection Coverage Area: 35' x 40'
Honeywell 5800PIR-COM	Commercial PIR motion sensor. Loop 1 = Low Sensitivity Motion Loop 2 = High Sensitivity Motion Loop 3 = Low Temperature Detection Coverage Area: 60' x 80'
Honeywell 5800PIR-OD	Outdoor PIR motion sensor. Uses Loop 1.
Honeywell 5800PIR-OD2	Outdoor PIR motion sensor. Uses Loop 1.
Honeywell 5800RP	Wireless repeater for Honeywell 5800 Sensors. Does not require enrollment, but can be assigned a single zone for RF supervision, low-battery, AC loss, and RF jam detection. This is done using Serial Number 1 with Loop 1, with DIP Switch 2 set in the OFF position. Can also use up to four (4) separate zones for supervision when DIP Switch 2 is set to ON. This is required for UL installations.
Honeywell 5800RPS	Recessed door/window sensor. Uses Loop 1.
Honeywell 5800SS1	Shock sensor. Uses Loop 1.
Honeywell 5802MN	Medical alert button. Uses Loop 1.
Honeywell 5802MN2	Medical alert button. Uses Loop 1.
Honeywell 5802WXT	Panic button. Uses Loop 1.
Honeywell 5802WXT-2	Panic button. Uses Loop 1.
Honeywell 5806W3	Smoke detector. Uses Loop 1.
Honeywell 5808W3	Smoke and heat detector. Loop 1 = Smoke & Heat Detection Loop 3 = Low Temperature Detection
Honeywell 5809	Fixed temperature and rate-of-rise heat detector. Uses Loop 1. Alarm occurs when the temperature exceeds 135 degrees Fahrenheit, or when the temperature rises more than 15 degrees Fahrenheit per minute.
Honeywell 5809FXT	Fixed temperature heat detector. Uses Loop 1. Alarm occurs when the temperature exceeds 135 degrees Fahrenheit.
Honeywell 5809SS	Fixed temperature and rate-of-rise heat detector. Uses Loop 1. Alarm occurs at 135 degrees Fahrenheit or when the temperature rises more than 15 degrees Fahrenheit per minute.
Honeywell 5814	Door and window sensor. Uses Loop 1.
Honeywell 5815	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5816MN	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switches
Honeywell 5816OD	Outdoor door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5817	Three (3) zone door and window sensor & transmitter. Loop 1 = NC or NO (DIP Switch Selectable) unsupervised. It does not use an End of Line Resistor (EOLR) Loop 2, 3 = NC Only. Both are unsupervised with no EOLR used
Honeywell 5817CBXT	Three (3) zone commercial transmitter. Loop 1 = Two (2) Terminals; Primary Loop supervised by 470k Ohm (yellow, purple, yellow, gold) EOLR. Resistor must ALWAYS be installed, even if Loop 1 is not programmed. If Loop 1 is used as a burglary zone, then Loop 4 must be programmed as a separate zone for Cover Tamper protection. Loop 2 = NC Reed Switch Loop 3 = Two (2) Terminals; NC Loop unsupervised, no EOLR required
Honeywell 5817XT	Three (3) zone door and window sensor & transmitter. Loop 1 = NC or NO (DIP Switch Selectable) unsupervised with no EOLR required Loop 2, 3 = Two (2) Terminal Blocks, NC Only
Honeywell 5818MNL	Recessed door and window sensor. Uses Loop 1. Not suitable for use in metal doors
Honeywell 5819	Three (3) zone shock processor. Loop 1 = NC for Inertia Style External Shock Sensor. This input provides a suitable fast loop response of from 1ms to 20ms, based on dip switch setting Loop 2 = Reed Switch Loop 3 = NC for Wired Contact, unsupervised with no EOLR required
Honeywell 5819S	Shock sensor and contact sensor. Loop 1 = Built-in Inertia Style Shock Sensor Loop 2 = Reed Switch Loop 3 = NC for Wired Contact
Honeywell 5819WHS	Three (3) zone shock processor. Loop 1 = NC, Built-in Inertia Style Shock Sensor Loop 2 = Reed Switch Loop 3 = NC for Wired Contact
Honeywell 5820L	Slimline door and window sensor. Uses Loop 1.
Honeywell 5822T	Garage tilt sensor. Loop 1 = NC for Wired Contact, unsupervised, no EOLR used Loop 3 = Tilt Switch
Honeywell 5834-2	Two (2) button key fob. Dual-button inputs allowed. Uses three (3) loops total, for a possible three (3) inputs. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5834-4	Four (4) button key fob. Dual-button inputs allowed. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5834-4EN	Four (4) button key fob. Dual-button inputs allowed. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5853	Glass break sensor. Uses Loop 1.
Honeywell 5869	Commercial panic switch. Uses Loop 1. Latches when tripped, key (provided) needed to reset it after it is tripped
Honeywell 5878	Six (6) button key fob. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible.
Honeywell 5898	Dual-tec motion sensor. Loop 1 = Low Sensitivity Motion Sensor. Pet immunity is available for this loop. 50lb or 100lb pet immunity, selectable via DIP Switch 1 Loop 2 = High Sensitivity Motion Sensor. Loop 3 = Temperature Sensor (High or Low, DIP Switch Selectable)

Just last week, Resideo purchased startup company Buoy Labs. This is the first acquisition from Resideo since the company completed its spin-off from Honeywell in October of last year. The purchase of Buoy Labs should greatly assist Resideo in its technology for environmental sensors.

Buoy Labs is best known for its smart home products that allow users to track the amount of water they use and quickly identify leaks. Their lineup fits in perfectly with Resideo. The company already offers many great flood detecting sensors. These include the Honeywell 5800FLOOD and the Honeywell 5821 when used with a Honeywell 470PB Probe or Honeywell FP280 Probe. Many of our monitored customers use these sensors to receive alerts in the event of a water leak. They can then take action before serious water damage occurs. This equipment works great with the wireless panels from Resideo, including the Honeywell Lyric Controller.

We believe that this acquisition will help Resideo make fantastic strides in its offering of environmental sensors, particularly for flood sensors. Buoy Labs has an impressive portfolio of smart home water management and water leak detection products. Resideo has cited industry studies claiming that homeowner's insurance companies pay more than $9 billion in water damage claims every year. The average claim is roughly $9,000. With the purchase of Buoy Labs, we expect that Resideo will achieve great success in reducing these figures and preventing house floods. And if you still don't think flood sensors are important, think again.

Alarm Grid will certainly keep you up-to-date with the latest news regarding any new environmental or flood sensors released from Resideo. This acquisition means Resideo has some big plans in store, and we are very excited to see what the future holds. Stick with Alarm Grid as we move forward in the exciting worlds of security, property protection and home automation!

Former "Malcom in the Middle" child star Frankie Muniz had a devastating experience last week. While visiting France to attend his uncle's funeral, Muniz's cat managed to turn on his sink. It flooded the house, destroying every wall, various pieces of artwork, personal photos and furniture.

The incident cost Muniz thousands upon thousands of dollars in damages to his five-story Phoenix house. He also lost priceless items that can never be replaced. It truly is a horrific event. We're sure that Muniz will overcome this challenge. He's a resilient man who currently serves as the host for "Dancing with the Stars: Juniors". He even recently got engaged. In the grand picture, this is just a small step back.

But we're also sure that this is a mistake he will never make again. Luckily, it's one that can be avoided fairly easily. Almost every security system can support flood sensors that can be used to let an end user know before serious water damage occurs. Once a small water leak is detected, the flood sensor will alert the alarm control panel. The user can then receive text and/or email alerts through an interactive service like Total Connect 2.0 or Alarm.com to let them know that their flood sensor has been triggered. Most flood sensors will activate with as little as a quarter-inch of water. This is well-before any serious water damage occurs.

Some users may wonder what to do if their flood sensor activates while they are away from home.The answer is fairly obvious. The user should determine the cause and stop the leak immediately if there is one. If you have a smart door lock, you can let a trusted friend or a neighbor into your home temporarily so that they can turn off the faucet or alert a plumber. You may also want to have security cameras in your home so that you can visually check for any flooding that may occur.

The thing to remember is that flood sensors are not very expensive. And many flood sensors will last as long as an alarm system itself. This one-time investment is much, much cheaper than the costs associated with a flooded home. Plus, many items are simply irreplaceable. If you value your home and your belongings, a few flood sensors is a small price to pay to protect what matters.

Some of our most popular flood sensors include the Honeywell 5800FLOOD, the 2GIG FT1-345, the Qolsys IQ Flood, the DSC WS4985 and the DSC PG9985. All of these sensors work very well, and they can save you thousands of dollars in the event of a serious water leak or accident. Just make sure the one you choose is compatible with your alarm system. You can purchase any of these sensors from the Alarm Grid website right now. Remember, stay smart and keep your home protected!

Hi DIYers! Today, we're taking a look at the Honeywell 5800FLOOD Wireless Flood and Temperature Sensor. This device provides monitoring for water leaks and extreme temperature changes. It will work with any panel that accepts the 345 MHz frequency, including most Honeywell and 2GIG Systems.

The 5800FLOOD is a great device for anyone who needs reliable monitoring for water leaks or potential flooding. The sign of a good flood sensor is the ability to detect leaks before they cause costly damage, without setting off any false alarms. The 5800FLOOD will activate once its built-in water probes have detected at least a quarter-inch of liquid. The device will respond within 22 seconds for a quick and accurate alert about the potential for water damage.

Alarm Grid recommends using the 5800FLOOD in places that are most prone to experiencing water damage. Popular locations include bathrooms, laundry rooms, furnace rooms, basements and garages. You will want to put the 5800FLOOD in the area of the room where a water leak will most likely occur or where the water is most likely to accumulate. Once the device detects a leak, it will send an alert to security system to let it know about the situation.

In addition to flood sensing, the 5800FLOOD also operates as a viable temperature sensor. The low-temperature loop will have the sensor respond upon detecting a temperature of 45 degrees Fahrenheit or lower for 10 consecutive minutes. This is great for catching a broken HVAC unit before the pipes freeze and cause serious damage. Meanwhile, the high-temperature loop will have the sensor respond after detecting a temperature of 95 degrees or higher for at least 10 minutes.

When programming the 5800FLOOD, the loop number that is set will determine how the sensor is used. There are three separate loops for flood detection, low temperature detection and high temperature detection. In order to use all three functions, the 5800FLOOD will need to be programmed to three separate wireless zones, with each zone being assigned the appropriate Loop Number. The table below outlines the Loop Numbers for the 5800FLOOD:

The 5800FLOOD Wireless Flood and Temperature Sensor is available from Alarm Grid now. Protect your home or business from serious water damage with this versatile and effective sensor!

It's the rainy season once again, and one thing you will certainly want to do is monitor your house for floods. This is done using flood sensors. These sensors will send an alert to the alarm system upon detecting water. This can help you detect a flood before serious damage occurs.

Flood sensors typically operate using a water probe. On these probes, there are pins that will cause the sensor to activate when they come into contact with water. Depending on the type of sensor, the pins may need to be exposed to water for a couple of minutes before the sensor will activate and an alarm will occur. This can be helpful for reducing false alarms and only alerting the system when there is a real flooding concern. Some probes come already attached to sensors. Others, like the Honeywell 470PB, will need to be wired to a separate sensor.

For best results, a flood sensor should be installed in a location where a flood is mostly like to occur. This can include basements, kitchens, laundry rooms and bathrooms. It is also a good idea to place these sensors underneath water heaters and sump pumps that could leak and cause serious damage. The earlier that the sensor is activated, the quicker that you can be alerted to the issue and properly solve the problem.

Flood sensors are excellent devices to pair with an interactive service such as Total Connect or Alarm.com. If the flood sensor activates while you are away from home, you will want to know about it as soon as possible. These services can send you text and email notifications as soon as a flood sensor activates. This way, you or a trusted neighbor can properly deal with the issue as soon as it happens. You may be able to stop the flooding before there is serious property damage.

When choosing a flood sensor, you must make sure it is compatible with your alarm system. This is especially true if you are using a wireless flood sensor. You will want to know which wireless frequency is used with your system and which type of wireless sensors are compatible.

Alarm Grid recommends the following wireless flood sensors for these different systems:

• Honeywell Systems: Honeywell 5800FLOOD
• 2GIG Systems: 2GIG FT1-345
• Qolsys and Interlogix Systems: Qolsys IQ Flood