AlarmNet Posts

When it comes to alarm panels behaving as Z-Wave Controllers, it should be easy to determine if a device is compatible or not. However, we've found that in some cases, not all Z-Wave devices are equal. Z-Wave locks by Schlage have been known to have compatibility issues with certain panels.

Alarm Grid has often stated in our documentation that we prefer that our customers use the Yale or Kwikset Z-Wave locks. We've seen issues with Schlage locks over the years and we haven't really gotten satisfactory answers as to why. We've had customers tell us that they've worked with Schlage, and we have worked with Resideo and Honeywell Home. Sometimes they will work, but other times the customer winds up changing to a different lock manufacturer, or just not using the locks with their panel.

When you look at the most current Lyric Z-Wave Compatibility Chart, which is dated 05/19, and is an official document produced by Honeywell Home, it shows that Schlage Z-Wave locks are compatible. This information is based on engineering and quality assurance testing. But testing and daily use are two different things. Engineers can never think up every scenario to test, no matter how hard they may try. So, once a customer attempts to use the products together in their own home or business, some unforeseen factors may arise and cause issues.

We recently had a customer attempting to use a Schlage Z-Wave lock with a Lyric Security System. When the lock is paired with the panel, the batteries drain very quickly, within one to two weeks. When the lock is used as a stand-alone device, the batteries appear to have a normal life. So, we asked Resideo Technical Support for their input. They suggested that the Schlage locks not be used with the Lyric, ProSeries, or Tuxedo products at this time. There is some conflicting information, certain locks may work with the ProSeries panels while others do not, but it may be best to avoid Schlage locks with these panels for now unless you can wait to use the panel and lock together until the issues are resolved.

The Lynx Series panels appear to support the Schlage locks when the L5100-ZWAVE is employed, but certain conditions must be met. The lock and the panel must be within 12 inches of one another during the pairing process, and must remain at this distance for a full two (2) minutes before either is moved. This allows the full pairing process to be completed. Also, the handing process must be completed immediately following pairing. Resideo engineers are working with Schlage to resolve any issues with those panels that have them, and they hope to have a resolution some time soon, possibly in early 2022.

If you have any thoughts about Schlage Z-Wave locks and their use with any of the Resideo or Honeywell Home alarm systems, drop a comment in the area below and lets get a conversation started. We offer feedback directly to all our vendors on behalf of our customers. We're honored to be your voice.

Until now, only alarm systems manufactured by Resideo, Honeywell Home, or Honeywell could be used with Total Connect 2.0. That changes with the new LTEM-P Series communicators. Some DSC and Interlogix panels can now be connected to and used with TC2. A supplemental wiring guide is provided.

The LTEM-PA AT&T LTE Communicator, and the LTEM-PV Verizon LTE Communicator available from Resideo can be used to send alarm signals on behalf of all the same VISTA panels that were compatible with the older AlarmNet communicators such as the Honeywell LTE-IA, and the Honeywell LTE-IV. In addition, certain versions of some of these panels can also be used with Total Connect 2.0 Remote Services when one of these communicators is attached to it.

With the release of the LTEM-P Series communicators, DSC PC1616, DSC PC1832, and DSC PC1864 panels can support both reporting through the communicator when it is connected to the panel's keypad bus and integration with Total Connect 2.0. In addition, Interlogix NX8E, NX-4V2, NX-6V2, and NX-8V2 panels can also be used with the LTEM-P Series communicators to both send signals, and integrate with TC2.

With the DSC PC Series panels, this is purely a keypad bus connection. The communicator's RX, TX, and Ground terminals will connect to the DSC panel's Green, Yellow, and Black keypad bus terminals. On the Interlogix NX Series panels that are supported, there is a connection to RX on the communicator from the terminal marked DATA on the panel's keypad bus. COM from the NX Series panel will connect to GND on the Communicator. In addition to this, the LTEM-P Series communicator will require a Resideo PRODCM Dialer Capture Module, which will connect to the panel's Tip and Ring terminals. The PRODCM will be installed inside the communicator. Panel signals are sent via the PRODCM, and Data Bus information for Total Connect 2.0 is sent from the bus.

There are some programming options that will need to be configured properly, for example the NX panel must be set to report in Contact ID format. In fact, all signals for both panel types will be sent to the monitoring station using Contact ID. The wiring connections should be made while both the panel and communicator are powered down. The alarm panel is powered up first, and all troubles, faults, and alarms must be cleared. Once they are, power up the communicator and it should begin to scan the panel's bus for zone information. This process can take up to ten (10) minutes.

This is not meant to be a step-by-step guide to setting up this feature, it's just an introduction to the feature for those who may not be aware that it is available. We offer an FAQ for using the DSC panels with TC2 here. If you have one of the compatible DSC or Interlogix panels, and you are considering using it with one of the LTEM-P Series communicators, check out the Resideo LTEM-P Series Installation Guide, the Resideo Supplemental Install Guide for Non-VISTA panels, and for those using a compatible Interlogix NX-Series panel, also check out the Resideo PRODCM Install Guide. We have not yet had an opportunity to create our own in depth FAQs for this process on the Non-VISTA panels, but we will get to those in the near future.

Have any thoughts about Resideo and Honeywell Home finally embracing the use of their communicators with competitor's panels? They offered a dialer capture module in the past, but it installed outside the communicator and was somewhat unwieldy. Leave a comment below and tell us what you think. We always look forward to hearing from our readers!

AlarmNet360 is both a website and an app that can be used to create, edit, and cancel AlarmNet accounts. Access to this website and app is only available for licensed alarm dealers who are affiliated with AlarmNet. As an end-user you will not need to have or create an AlarmNet360 account.

Being a DIYer in the alarm industry can be pretty confusing at times! Nearly all of the documentation provided with alarm systems that have historically been installed only by alarm professionals is intended only for alarm professionals. So, when you buy that new ProSeries or Lyric Alarm System, and you begin reading the installation instructions, one of the first things you are told to do is create an AlarmNet360 account. This is not something that you, as a DIYer will be able to do.

This is where Alarm Grid comes in. Alarm Grid is a DIY friendly company. We sell professional grade alarm systems to anyone who wants to buy them. Sometimes, alarm professionals purchase from us and then they go about configuring the system themselves because they have access to AlarmNet360. Sometimes, customers purchase from us and then hire their own alarm professional to install their system and that alarm professional completes the setup on AlarmNet360 themselves. But usually, when an individual buys a system from us, they then sign up for one of our no-contract monitoring plans, and then we set up their account through AlarmNet360.

The relationship between Alarm Grid and our monitoring customers is a symbiotic one. DIY alarm users choose not to pay a professional to do something that they can do themselves. That being the physical installation of the alarm equipment. With the proliferation of self-contained, all-in-one systems, installation has gotten more and more simple. A child can do it. We have several young customers in their teens who set up systems just because they enjoy doing it, and figuring out new and interesting ways to make things happen.

On the monitoring side of things, that's where restrictions start to come in. There are certain things that have not opened up to DIYers yet, and access to AlarmNet360 is one of those things. You may be thinking, "Forget AlarmNet360, what's AlarmNet?" You can read about AlarmNet here. At present, only alarm dealers can sign up for access to AlarmNet360 in order to be able to add, edit, or cancel AlarmNet accounts. Access to accounts is very tightly controlled. The only accounts that Alarm Grid can see in AlarmNet360 are accounts that are assigned to Alarm Grid, which usually means that Alarm Grid created them in the first place.

Alarm Grid chose the DIY business model in part because we have everything we need to administer accounts on the back end, but we don't have a team of installers to send out and put in systems. DIYers are our installers, and in turn we provide for them the account admin services that they are not allowed to perform for themselves. We sell reasonably priced, professional grade alarm equipment. The same equipment that just about any alarm dealer in the country will sell you, and we handle the administrative side of things, in addition to providing free, world-class technical support to our monitored customers. In exchange for that, we charge a reasonable monitoring fee with no activation fees, no cancellation fees, and no contracts. We also don't care if you buy your system from us or elsewhere. We will monitor any equipment that is within our power to monitor for the same prices we charge to monitor the equipment we sell.

So, when you crack open that new system, and start reading the instructions, skip the part where it talks about the AlarmNet360 account. Whoever you sign up for monitoring with will take care of that part. Do you have an AlarmNet communicator? Have you been stumped by the mention of AlarmNet360 in your system's documentation? Leave us a comment below and let us know if this information was helpful. We always look forward to hearing from you.