Owner DIY Posts

Alarm.com continues to improve the user experience with its service. They made swapping a communicator or a whole system easy when it comes to backing up and restoring users and zones. But until now, all Z-Wave devices had to be excluded then re-included on the new panel. That is changing.

An important thing to remember is that currently, not all Alarm.com compatible Z-Wave Controllers support backing up and restoring the Z-Wave network. The following modules are the ones that support this feature as of this writing:

NOTE: To find a Z-Wave Module's SDK Number, a dealer can log into the Alarm.com Partner Portal, pull up the customer account then go to Equipment > Z-Wave Devices. The module's SDK number can be located in "Z-Wave Controller Information" which is found under "Modem Z-Wave Chip Details".

As you can see from this list it's the communicators manufactured by ADC, that have the Z-Wave controller built into the communicator, that currently support this new feature. Hopefully, this list will grow to include the Qolsys and 2GIG alarm panels.

At this time, the backup and restore of a customer's Z-Wave network can only be performed by the alarm dealer through either the Partner Portal, or the Mobile Tech App. The end-user can't perform these steps. A Z-Wave network backup occurs automatically about eight (8) hours after a device is either added to, or removed from, the Z-Wave network. The backup takes about five (5) minutes, plus two (2) to three (3) minutes for verification purposes. The amount of time the back process takes is not dependant on the number of devices that are paired with the Z-Wave Controller.

To backup a Z-Wave Network on a compatible device using the Alarm.com Partner Portal (Website) perform the following steps:

1. Login to the Portal. Using your Alarm.com dealer portal login credentials, log into the Partner Portal, completing any 2-factor authentication required.
2. Pull up the account. Find the account whose Z-Wave network you would like to back up.
3. Navigate to equipment. Click on the Equipment menu option on the left side of the screen. Then click on Z-Wave Devices.
4. Backup the network. Under Advanced Z-Wave Commands click "Backup Network". Stay on the network backup page to monitor the status of the backup. Once backed up, the backup will be verified, then the process will complete.

A backup is usually performed in order to prepare to move as much of the panel/module programming from the existing system to a new module. This could be due to an upgrade, or due to the replacement of an existing module that is determined to be malfunctioning.

Once a backup has been made, the next step is to restore the backed-up information to the new module or system. To restore backed-up Z-Wave information to a new module during a module swap, via the Alarm.com Partner Portal, perform these steps:

1. Power down the existing module. Power down the panel and remove the existing Alarm.com module from it.
2. Swap the module. Log into the Alarm.com Partner Portal, then find the customer account. In the Customer Information section, choose Swap Module. Enter the new module's serial number into the appropriate location on the module swap screen. If there is a specific reason for the swap, enter this info in the Swap Reason field.
3. Restore Z-Wave Network. Click on the option to Restore Z-Wave Network then click Submit.
4. Install new module. Install the new Alarm.com module into the panel (while still powered down). Power up the panel and module.
5. Perform a Communication Test Perform a communication test from the panel using the new communication module. The process for sending a test signal will differ from one panel to another. Check the Installation Instructions for the new module, it should provide instructions on how to perform this test.
6. Monitor the process. You will automatically be taken to the Z-Wave Network Restore page. Monitor the progress of the restore until it is complete. The process of a full module swap, including restoring panel information as well as Z-Wave devices can take 25 minutes or longer. Be patient and allow the process to complete.

What do you think of this new feature from Alarm.com? If you have ever had to replace a Z-Wave Controller in a robust Z-Wave network and had to exclude, then include all the devices in the new module along with re-programming all schedules and scenes, you will appreciate this feature. Leave a comment below and tell us about your experiences with this type of situation. We enjoy hearing from our readers.

Alarm Grid customers with PROA7/PROA7PLUS panels who use Night Stay Arming may have received notification calls in error when arming their system in this mode. This issue came to light recently, and we have resolved it with the monitoring station, CMS. We apologize for any inconvenience.

The Honeywell Home PROA7, Honeywell Home PROA7PLUS, Resideo PROA7C and Resideo PROA7PLUSC are the newest All-in-One (AiO) panels from what used to be Honeywell and is now Resideo. The difference between the Honeywell Home versions, and the Resideo versions is strictly cosmetic as you can see below, with one panel having Honeywell Home branding and the other having Resideo branding:

When an alarm panel reports a signal to a monitoring station, it does so in a particular format. The most prevalent format used by the PROA7 and PROA7PLUS panels is called Ademco Contact ID. With Ademco being the creator of the format (and the company Honeywell purchased to get into the security system manufacturing business). In a Contact ID Signal the information transmitted follows this format:

Further, monitoring stations have Automation software that receives the above signal and turns it into useful information. The account number is turned into "The Smith Residence at 123 Smith Ln, etc...." An E131 is turned into a Perimeter Burglary Alarm (R131 would be a restore of a previously reported perimeter alarm), Partition is self explanatory, and a Z003 would indicate that this is a perimeter alarm on Zone 003, automation turns this into something like "Living Room Window". If the signal is an arming or disarming event, then instead of a Zone Number, the monitoring station would receive a User Number to indicate who armed or disarmed. For a full list of 3-Digit Contact ID codes, check the Installation Instructions for your alarm panel. All Honeywell, Resideo, and Honeywell Home panels have a list of the Contact ID Codes that can be transmitted by the panel, and what they mean.

The problem occurred because Honeywell Home and Resideo changed the Contact ID code they use when the system is Armed to Night Stay Mode. In the past, panels such as the Lyric and the LynxTouch panels used the Code R441 to indicate any type of Stay Arming, including Night Stay (in arm and disarm signals a Restore is reported when a user Arms, and a new Event is reported when a user Disarms.) On the ProSeries panels, they chose to use R444 to indicate when a user armed in the Night Stay Mode, while reporting an E401 to indicate when the system was disarmed. E401 is a more generic "Disarm by User" signal. This is also unusual, as in the past the panel would have reported an E444 when the system was disarmed from this mode.

Since this is an unusual signal to receive, and the monitoring station didn't have default instructions in their automation system on how to treat it, when it was received they chose to err on the side of caution and called the premises to report it. This is not the normal default protocol for signals regarding arming and disarming. Once we became aware that there was an issue, we investigated with the monitoring station, confirmed the issue, and took steps to be sure these signals would be treated properly in the future. We are doing the same with Rapid Response, the monitoring station for our Canadian customers. Once again, we apologize for any inconvenience this may have caused and we look forward to serving all our customers, old and new, in 2022!

In 2021 we said goodbye to some products (here's lookin' at you, Qolsys IQ Panel 2) and hello to others. We'll take a look back on 2021 and highlight some of the changes we've seen in the industry. From new Alarm.com cameras to redesigned alarm panels, here's a look back at 2021, as it was.

January, 2021: The new year saw the release of the Alarm.com ADC-V515 Camera. This budget-friendly camera offers 1080p recording with High Dynamic Range (HDR) and a 110° field of view. The IR Night Vision feature has a range of ~15 feet. This is an indoor camera that connects to 2.4 GHz WIFI networks, and it supports the full suite of Video Analytics features.

We also said goodbye to the Honeywell 5877 Garage Door Relay. This product works in conjunction with the Honeywell Wireless Alarm Panels, with the exception of the ProSeries panels, to allow automation and remote control of a garage door. We said "Goodbye" to it in January, but we should have said "See you later" because in October we said "Hello" again! Alarm Grid was able to obtain a number of 5877s, and we'll continue to offer it until stock exhaustion. Since Honeywell has decided they will no longer produce it, at that point, it will be "Goodbye forever".

February, 2021: In February, Alarm.com announced the discontinuation of the ADC-SVR122. Although they still offer the ADC-CSVR126 this is a commercial version of the SVR122, and may not be suitable for the average residential user. In lieu of using a Stream Video Recorder, Alarm.com offers the Onboard Recording feature as an alternative to a traditional residential DVR. Click here for a list of cameras that support this feature.

March, 2021: In March, Resideo discontinued the IPCAM-WOC1, leaving their Total Connect 2.0 product with no outdoor camera option. Later in the year, they released a replacement, so TC2 users will have an outdoor camera choice, but until recently the IPCAM-WOC2 was on backorder due to supply chain issues. It is now available for purchase again and ready to ship!

Honeywell Home added the PROA7 panel to the ProSeries Lineup that they released late in 2020. In reality, the Honeywell Home PROA7 and PROA7PLUS are basically the same products as the Resideo PROA7C and PROA7PLUSC, but with different branding on the front of the panel. The PROA7 and PROA7C are "Lite" versions of the PROA7PLUS and PROA7PLUSC. The non-plus versions have no front-facing camera for disarm photos and don't support Bluetooth. They will support WIFI and Z-Wave, but don't come with the Honeywell Home PROWIFIZW built-in. For these panels, if you want WIFI, but no Z-Wave, you can choose to add the Honeywell Home PROWIFI module instead. All of the ProSeries panels support the addition of either the PROLTE-A or PROLTE-V LTE Cellular Communicators and the Honeywell Home PROTAKEOVER legacy wireless takeover module.

April, 2021: In April, 2GIG released the 2GIG Edge. They teased their newest panel for quite some time, via its own countdown webpage. After a couple of release date changes, on April 1, 2021 it became available. The Edge was an instant sensation, with a number of industry awards in addition to an honorable mention. The Edge has a strong feature set, and comes in both an Edge AT&T LTE and an Edge Verizon LTE version. Dual-path ready, with 100 Zones, 100 User Codes, Z-Wave Plus V2, and Facial Recognition Arming and Disarming, the Edge is an excellent option for a new and modern security system.

May, 2021: With the release of the 2GIG Edge, the GC3e was discontinued upon stock exhaustion. Alarm Grid originally retained some stock of the product, and offered it at an attractive price for a limited time, until our stock was exhausted. The 2GIG GC3e has now gone the way of the dinosaurs. Also in May, Alarm.com announced new support for Ecobee Smart Thermostats via server-to-server integration.

June, 2021: Alarm.com announced the release of some new System Enhancement Modules (SEM) to support the Honeywell VISTA-10P, VISTA-15P, VISTA-20P, and VISTA-21iP panels. These are Dual-Path communicators with lower power consumption than their predecessors, with the ability to be used without an external power supply. The ADC-SEM300-VT-AT uses AT&T LTE while the ADC-SEM300-VT-VZ uses Verizon LTE.

In June, Qolsys also introduced two (2) Smart Water Valve Kits. The Qolsys IQWV908-KIT-PG includes the DSC PG9985 PowerG Flood Sensor coupled with Qolsys' Z-Wave Plus 700-Series Smart Water Valve. With these two products, you can have your system sense a water leak in the early stages, and through an Alarm.com Automation Rule, automatically turn off the water until the issue can be resolved. The PowerG sensor provides exceptional wireless transmitting range. It can work up to 4,000 feet (1219m) away from a Qolsys IQ Panel 4 without a repeater being required, and will work with all variations of that panel.

Qolsys also introduced the Qolsys IQWV908-KIT-SL. This kit includes the same great Z-Wave water valve, but with a Qolsys IQ Flood-S 319.5 MHz flood sensor for use with the Qolsys IQ Panel 2 & 2 Plus 319.5 MHz version or Qolsys IQ Panel 4 AT&T 319.5 Mhz version or Qolsys IQ Panel 4 Verizon 319.5 MHz version, or even one of the Interlogix panels that support the 319.5 MHz frequency. This flood sensor will only work with the 319.5 MHz version panels, so be certain which panel you have when ordering.

Resideo and Honeywell Home introduced a firmware update for the Honeywell Home PROA7 and PROA7PLUS, and the Resideo PROA7C and PROA7PLUSC that enabled programming through the panel touchscreen (or via a remote touchscreen keypad, the PROWLTOUCH or PROWLTOUCHC). Many users had been waiting not-so-patiently for this update, particularly DIY users who prefer to handle their own panel programming. Prior to this update, referred to as MR3, only an alarm dealer could program the ProSeries panels and only remotely via AlarmNet360 or via the AlarmNet360 Mobile App.

And finally, in June we discovered that the 2GIG Edge had a limitation with regard to using Image Sensors. Namely, that at the time of the panel's release, the 2GIG IMAGE3 only behaved like any other motion sensor when paired with the panel. It did not provide any alarm images, or the ability to peek in. Fortunately, in August 2GIG released Firmware Version 3.1.0.011, which solved this issue.

July, 2021: Honeywell Home announced in July the addition of the PROSIXRPTR Encrypted Wireless Repeater. Up to two (2) repeaters can be used with each ProSeries system and each repeater increases the range for PROSIX and SiX Series sensors by about 200 feet (60m).

Qolsys released the Qolsys IQ WIFI just ahead of ISC West. This product allows the alarm dealer to control all, or a portion of the customer's network to provide for easier alarm system integration to WIFI, as well as easier remote troubleshooting. Up to eight (8) IQ WIFI devices can be used per network with one (1) behaving as the controller, while up to seven (7) behave as agents. Locally, the IQ WIFIs can be configured using the touchscreen on a Qolsys panel (IQ Panel 2 must be version 2.6.0 or higher).

Z-Wave continued to evolve in 2021, and we began to move up from Z-Wave Plus to Z-Wave Plus V2 products. Z-Wave Plus uses the 500-Series Chipset, while Z-Wave Plus V2 uses the 700-Series Chipset. The 2GIG Edge uses a Z-Wave Plus V2 Chip as does the Qolsys IQ Panel 4. We've received no word on when, or if the ProSeries panels from Resideo and Honeywell Home will move up from the 500-Series Chipset to the 700-Series. You can read about the differences between the versions of Z-Wave here.

August, 2021: August was a sad month for us at Alarm Grid. We lost our beloved, and prolific writer Michael Goris suddenly and unexpectedly. Not only did Michael write about everything having to do with alarms, he was also featured in many of our videos, particularly once COVID-19 hit hard and we couldn't all always be in the office together. We miss you Michael.

Resideo and Honeywell Home announced compatibility issues between certain of their 6160RF keypads and the 5800WAVE or 5800RL products. The issue had to do with the 6160RF not sending correct status information from the panel to the 5800WAVE or 5800RL. This issue affected keypads manufactured between May 26, 2020 and February 18, 2021. You can read the full post about it here to determine if you have a keypad that may be affected.

September, 2021: Resideo and Honeywell Home announced in September that the Weather feature on the TUXWIFIW and TUXWIFIS would no longer be available. This, after they had issues for months with the information for this screen not updating properly. In the final week of December, we received good news that this issue has been resolved and that the weather for these products is now operating as it should!

On another positive note, the Resideo and Honeywell home ProSeries panels won the CEPro Best Product Award. Specifically, they won the award for Best Integrated Security System/Module/Device/Surveillance Camera System. You can read the full announcement here.

October, 2021: In October, Alarm.com announced the release of the Alarm.com ADC-V724 their first outdoor camera that supports 2-way audio. In addition, it supports the full suite of video analytics, and onboard recording, it also supports dual-band WIFI and IR Night Vision with a range of up to 49 feet (15m). This camera came out just in time for homeowners to really mess with the trick-or-treaters in their neighborhood using the 2-way audio feature!

In October we also got a sneak-peek at the new Resideo IPCAM-WOC2, which replaced the IPCAM-WOC1. Briefly, we had a new supply of outdoor cameras that were compatible with Total Connect 2.0, however we sold out pretty quickly. Supply chain issues had this camera back on the unavailable list but as of December, 2021 it is back in stock and ready to ship.

Resideo and Honeywell Home announced in October that with Firmware Version 03.592.107.0 for the ProSeries panels the Honeywell Home PROTAKEOVER Legacy RF Receiver module will now support wireless life-safety devices. Although you can now program any supported legacy RF device for life-safety, the Honeywell 5800 Series wireless devices have actually been tested to ETL standards for Residential Fire. This update also brought other exciting features and fixes. You can read all about them here.

November, 2021: This is the sad month we knew would come when the Qolsys IQ Panel 4 was announced earlier in the year. In November, Qolsys announced the End of Life for the Qolsys IQ Panel 2 Plus 319.5 MHz panel versions. Users can now purchase the IQ Panel 4 in the 319.5 MHz flavor. As supply chain issues abate, the IQ Panel 4 345 MHz option, and the 433 MHz option will become available, and as they do, their corresponding IQ Panel 2 Plus versions will also be discontinued.

We also discovered in November that the IQ Panel 4 will only support the newest version of the Qolsys IQ Remote. An easy way to tell if you have the newest version of the IQ Remote is to look for the front-facing camera. If the camera is in the top center, you have a newer keypad. If the camera is in the upper-right corner, then you have an older IQ Remote that won't work with the IQ Panel 4. Read our full notice on this information.

December, 2021: In December we received critical notices from both Alarm.com/Qolsys and AlarmNet that a couple of their products will require a firmware update prior to the 2022 AT&T 3G Sunset. For AlarmNet, any Lyric Controller with a LYRICLTE-A AT&T LTE Communicator installed must be updated prior to 02/22/22. Read the full notice from AlarmNet and Resideo. The Verizon communicators are not affected by this notice.

On the Alarm.com side, the Qolsys IQ Panel 2 and IQ Panel 2 Plus panels with an AT&T LTE Cellular Communicator also require an update prior to 02/22/22. In some cases, the panel firmware needs to be updated first, before the cellular firmware update can be implemented. Read the full notice on the Alarm.com update requirement. Again, the Verizon versions of these products are not affected.

So that's it, 2021 in a nutshell. As is usually the case, it has been a year full of ups and downs. We have seen a lot of positive change in our industry. The era of COVID-19 has exposed some opportunities in the physical safety world that may not otherwise have been considered without the pandemic having occurred. Touchless doorbells, and biometric system control are just a couple of things that have come to fruition during this time. I don't know about you, but I can't wait to see what 2022 has in store for us.

It's the most wonderful time of the year, and we'd like to take this opportunity to wish all of you a Happy, Safe, and Healthy Holiday Season! Regardless of which of several holidays or traditions you observe, we at Alarm Grid hope this season finds you surrounded by loved ones and festivities.

The Alarm Grid team will be celebrating the holidays starting at 6:00 pm on Thursday December 23, 2021. Our offices will close at that time, and will reopen on Monday, December 27, 2021. During the time our office is closed we won't be here to answer support phone calls or emails.

Our central station partners, of course, will be available during this time. All signals sent by your Alarm Grid monitored alarm system will be handled as usual. If you need to contact the central monitoring station, to cancel a false alarm or verify a signal, customers in the US can contact Criticom Monitoring Services (CMS) by dialing (888) 818-7728 and choosing Option [9].

Canadian customers can contact Rapid Response at (800) 932-3822. Remember when you call either monitoring station, you will be asked for your name, address, and your false alarm password or phrase. Providing incorrect information when asked, will result in the dispatch of authorities.

If you have a support question, or need to make adjustments to your account, the monitoring station cannot assist you with that type of request. In that case, send an email to support@alarmgrid.com with details of your request and we will begin to address these support issues as soon as we return to the office on Monday, December 27.

As we prepare to say goodbye to 2021, we want to say thank you to our customers. Thank you for trusting us with your safety and security. It is a privilege that we don't take lightly. Relax, and enjoy this time with your family and friends.

Users of the Lyric Alarm System with an LYRICLTE-A AT&T LTE Communicator installed take note. Resideo has identified an issue where, after the AT&T 3G sunset on 02/22/22, any panel not properly updated will lose its connection with the cellular network. This issue does not affect Verizon units.

The firmware version that resolves this issue is 01.09.07772.494, and it is available now on the Resideo AlarmNet360 servers. The issue at play here is that the AT&T cellular communicator currently falls back on the 3G network when it can't connect to LTE. Once an LYRICLTE-A communicator is registered, it looks for both an LTE signal and a 3G one. Without this critical firmware update, these communicators would continue to look for a 3G signal after the 3G sunset. Being unable to find a 3G signal, they will lose connection and go offline.

Users who find themselves in this situation have a few options. If you are a Lyric Alarm System user with the AT&T LTE communicator installed, you can choose to go ahead and manually update your system now. The system needs to be disarmed and have no trouble conditions present in order for the firmware update to go through, so a manual update allows you to choose a time when it is disarmed and ready. It also allows you to confirm that the update was successful after you see your panel reboot.

Since this is a critical update, AlarmNet will begin automatically updating panels that are affected by this issue starting on December 8, 2021. Since a firmware update can only go through when the panel is disarmed with no troubles, any users with a zone trouble, or a low battery message that they have been putting off correcting, should go ahead and take care of the issue. Once all trouble conditions are clear and the system is disarmed, we recommend that you go ahead and manually perform the firmware update. Instructions for updating are linked above.

If your system is automatically updated, it will reboot as part of the update process, so don't be alarmed if you see this happen. Step 3 in the FAQ on updating the panel linked above shows you how to confirm the panel's firmware version. So, if you see your panel reboot you can verify that an update was successfully completed.

Any Lyric Controller with a LYRICLTE-A AT&T LTE Communicator that is being installed on or after 02/22/22 will need to be updated to firmware version 01.09.07772.494 via the built-in WIFI communicator before the LYRICLTE-A will work properly. The firmware update should be completed prior to the installation of the LYRICLTE-A. The LYRICLTE-V Verizon LTE Communicator is not affected by this issue. You can read the full notice from Resideo here.

Beginning on December 6, and continuing through December 31, 2021 Alarm Grid customers who subscribe to Alarm.com video service can capture a picture of Santa Clause as he visits their home. Not all cameras have the ability to capture images of Santa, but Alarm.com has a few cameras that do.

The following cameras offered by Alarm.com are capable of capturing Santa's image:

• ADC-V515
• ADC-V520
• ADC-V521IR
• ADC-V522IR
• ADC-V523
• ADC-V622/ADC-V622-WELL
• ADC-VC726
• ADC-VC736
• ADC-VC826
• ADC-VC836
• ADC-V722W
• ADC-V723
• ADC-V724

Any Alarm Grid customer with one of the cameras listed above and a monitoring plan that includes video has the ability to take advantage of this rare opportunity to see the big man in action. There are limits to this technology, though. The only way you can see Santa is through a still image captured within a screenshot. He moves so quickly, you can't possibly catch him in an actual video clip.

The ability to grab an image of Santa is only available through the Alarm.com Customer App, not through the web page. In order to support this feature, iOS users must be on version 4.17 and higher of the app, while Android users must be on version 4.15.1 and higher. The Alarm.com app is available as a free download through the Apple App Store or the Google Play Store.

To use this feature, log into the app using the proper credentials, completing any two-factor authentication that you may have setup. Once you're logged in, click on the menu icon in the upper left (≡) then tap Video from the list of menu items. Select the live video feed of any of the compatible cameras listed above that you may have associated with your account. Click the Santa icon available near the top of the live stream:

This is when the magic happens! The first time you click on the icon, a pop-up window will show you how to capture the proper image for your situation. For cameras and images in full light, Santa may appear in color. If the image is captured at night, then Santa may appear in black and white. Once you have the image, you can either choose to share it, download it, or both.

It's that simple! This magic "Santa Filter" is only available until the end of December. After that, we'll have to wait until next year to see if this particular Holiday Magic will be available again then. Alarm Grid customers with a Platinum Plan (Self or Full) or with a Stand-alone video plan can take advantage of this opportunity.

Local Alarm Mode, also called Demo Mode, is a way for an alarm dealer to demonstrate the full features of the panel without having to register it to an AlarmNet360 account. However, while in this mode, panel communications can't be configured. A panel in this mode can seem to be broken.

Alarm Grid has seen several of the Honeywell Home PROA7, Honeywell Home PROA7PLUS, Resideo PROA7C, and Resideo PROA7PLUSC panels recently that have either arrived with Local Alarm Mode enabled, or have been put into this mode during initial setup. Once Local Alarm Mode has been enabled, it is impossible to configure the panel communication settings until Local Alarm Mode has been toggled off.

Local Alarm Mode is a valuable tool that has been made available to alarm dealers so that they can demo these new panels for a customer in spite of the fact that the panel isn't associated with an account. This was particularly important when the panel was first introduced because there was no local programming. For those early panels, until the ProSeries panel was registered, it couldn't do much unless Local Alarm Mode had been enabled.

This was a great tool at the time for alarm dealers, but for DIY customers, it doesn't offer much in the way of benefits. Now that the panel has local panel programming available, there really is no reason for an Alarm Grid customer to want to use this feature. Whether the panel arrived with this feature enabled, or the feature was enabled during programming, once the customer decides to have the system monitored, whether self monitored, or with central station monitoring, Local Alarm Mode should be disabled.

To check to see if Local Alarm Mode is enabled or disabled, choose the Menu icon (≡) at the bottom center of the Home screen. Select Tools > Installer Code (default is 4112) > Local Alarm Mode. The feature can then be toggled OFF if it is enabled. If it was enabled and you toggle it off, you'll see a confirmation screen, click on the "YES, DISABLE" option.

If you've been using the system with Local Alarm Mode enabled, and you have signed up for alarm monitoring with Alarm Grid, be sure to toggle this feature OFF as soon as possible. Depending on which monitoring plan you sign up for, activation of your account may begin immediately after sign up, and having this feature enabled at that time can cause delays. This is particularly true of the Self-Monitoring options. If you signed up for a central station monitoring plan, just be sure to disable this feature prior to your activation appointment.

From all of us at Alarm Grid, Happy Thanksgiving! We send you good wishes for a healthy and happy day with your friends and family. Whether you celebrate Thanksgiving, Friendsgiving, or just Giving Back we hope you stay safe and warm. Be sure to arm your security system, and lock your doors.

We at Alarm Grid understand the importance of spending time with loved ones, so we will be closed on Thanksgiving to give our employees the opportunity to celebrate. Of course, our central monitoring stations will both be available to handle any alarm signals that may be sent by our customer's systems. If you need to contact the monitoring station, to report a false alarm or put your system on test, you can call Criticom Monitoring Services (CMS) at (888) 818-7728 and choose Option [9]. This is the process for customers inside the United States.

If you are a Canadian Alarm Grid customer, then you will contact Rapid Response, our monitoring partner in Canada at (800) 932-3822. Remember, when you call you will be asked for your name and address, and to verify your false alarm password or phrase. Providing the wrong information, or the Duress Password will result in a police dispatch.

If you have a support question, or need to make adjustments to your account, the monitoring station won't be able to assist you with that. In that case, send an email to support@alarmgrid.com with your request and we'll get back with you as soon as possible when we return to the office on Friday, November 25.

As we begin the 2021 holiday season, we give thanks for our health, our employees, but most of all for our wonderful customers. It is truly our pleasure to help you keep your family and your property safe and secure.

Update 12/02/21:

We have confirmed with Resideo and at least one customer that the issues regarding the syncing of Automation between all versions of the Tuxedo Keypads, and the VAM have been resolved and that remote control of Z-Wave devices has returned to normal. Users should now be able to remotely control Z-Wave Automation Devices during any Total Connect 2.0 session. Any Alarm Grid customer that notices issues like this in the future, please report it to support@alarmgrid.com.

Update 11/26/21:

On Tuesday of this week, Resideo announced an update meant to fix this issue. Apparently, it fixed the portion of the issue where all Automation Syncs were failing, but did not address the issue with being unable to control Z-Wave Devices remotely.

There is something of a workaround for this portion of the issue at this time. During the TC2 session where a successful Automation Sync occurs, you can control Z-Wave devices remotely. Once you end that TC2 session and begin another one, you will lose that ability. So, for now, if you need to control a Z-Wave device remotely, perform a sync, and once you see in the Activity Log that the Automation Sync was successful, you will be able to control Z-Wave devices until the current TC2 session ends. Stay tuned and we will provide further updates as this issue is resolved.

Original Post:

In the last couple of weeks, Alarm Grid has noticed several customers with VAM and Tuxedo Keypads (all versions) having trouble syncing Z-Wave devices with Total Connect 2.0. This prevents newly added Z-Wave devices from showing up in TC2, though local control at the device is still available.

This issue doesn't seem to affect Total Connect 2.0 accounts associated with AiO (All-in-One) panels such as the Lyric Controller and the Honeywell Home PROA7PLUS. Accounts with these panel types should be working fine. It is unknown exactly what the problem is, and there is currently no workaround available. We've been in touch with Resideo and Honeywell Home and they are aware of the problem, but there is no Estimated Time of Resolution (ETR) for a fix.

You can continue to add and remove Z-Wave devices locally at the VAM or Tuxedo. But any changes that are made locally at the Z-Wave controller will not be synced to Total Connect 2.0. This means that any device deleted locally will continue to show up in TC2, and any device added locally will not show up in Total Connect 2.0 until this issue is resolved and a successful automation sync occurs.

Any device that currently shows up in Total Connect 2.0, and still exists in the Tuxedo or VAM CANNOT be controlled remotely through TC2. When an attempt to perform an Automation Sync occurs, there is no Automation Sync Failed, or Automation Sync Successful message displayed in TC2 Activity. Status changes from the Z-Wave device to TC2 seem to be coming through fine. It's only the sync process and remote control that seem to be having issues.

Alarm Grid is working with Resideo and Honeywell Home, and as soon as this issue is resolved, we'll post about it here. We posted information earlier this year about the Tuxedo Keypads and VAM Automation Controllers not updating the weather properly. We don't know if this current issue is related to the previous one, but we hope that it will be resolved soon. Stay tuned to our blog for updates.

Here at Alarm Grid, we recently learned that the Qolsys IQ Panel 4 supports the Qolsys IQ Remote, but only the most recent iteration. Older Qolsys IQ Remotes are not compatible. If you plan to replace a Qolsys IQ Panel 2 with an IQ Panel 4, read on to see how you can tell the keypads apart.

As of now, only the Qolsys IQ Panel 4 AT&T LTE, Interlogix/GE Compatible version, and the Qolsys IQ Panel 4 Verizon LTE, Interlogix/GE Compatible version are available. The other iterations of the panel will become available in the next couple of months. The only touchscreen keypad that is currently compatible with these panels is the Qolsys IQ Remote, and only the latest version with P/N QW9104-840, at that. Keypads with a P/N of QW9103-840 or below are not compatible. The sticker showing the part number should be on the back of the keypad.

Below, you can see the back of an IQ Remote with the P/N: QW9103-840. This keypad is not compatible with a Qolsys IQ Panel 4:

Looking at the sticker on the back of the keypad is the first way to easily determine whether the IQ Remote will work with the IQ Panel 4 or not. But, what if the sticker has been removed, or the touchscreen keypad has been mounted to the wall and the back side is difficult to access? There is another easy way to tell whether the IQ Remote you have is the older or newer version.

When the IQ Remote was re-designed, the front-facing camera was moved from the upper right corner to the center of the keypad. This was done, in part to better match the look of the Qolsys IQ Panel 2/2 Plus. Checking the location of the camera is the easiest way to determine whether it is a newer or an older Qolsys IQ Remote.

Below you can see one of the original Qolsys IQ Remotes. You can see that the camera is located in the upper right corner of the keypad.

Below is an image of the newer Qolsys IQ Remote, P/N QW9104-840. You can see the camera has been moved to the front center, and in the upper right corner you can see that a microphone has been added:

Checking the camera location is by far the easiest and quickest way to determine if the IQ Remote you have is compatible with the Qolsys IQ Panel 4. It's rumored that a PowerG Touchscreen Keypad is in the works, which, if true will likely make the IQ Remote obsolete given the superior wireless range of the PowerG protocol.

The Qolsys IQ Panel 4 can support up to three (3) IQ Remotes, but it also supports the use of up to five (5) Wireless PowerG Keypads (WS9LCDWF9, HS2LCDWF9, and HS2LCDWF9ENG) and up to two (2) Hardwired DSC Keypads (HS2LCD, HS2ICN) per DSC PG9WLSHW8 PowerG Wired to Wireless translator module. Up to two (2) modules are currently supported per panel, so up to four (4) of the wired keypads can be used. This gives a total of up to 12 remote keypads.

Have comments, questions, suggestions? Leave a comment below and we'll be happy to respond. Our support hours are from 9:00 am - 8:00 pm Eastern Time, Monday - Friday, and our support email is support@alarmgrid.com. We always look forward to hearing from you.