Owner DIY Posts

Recently, we told you about T-Mobile customers who, in the past received MMS notifications with video thumbnails, but now receive SMS notifications with a link. Alarm.com will soon unveil a Push Notification Migration Tool to encourage and help users to switch from SMS to push notifications.

You may be asking, what's the difference between SMS, MMS, and push notifications? SMS or Short Message Service is a text message delivered to your phone through your phone carrier. Changes undertaken by the cell phone carrier can affect how and when you receive SMS notifications, or whether you receive them. These changes are outside the control of Alarm.com.

MMS is Multi-Media Service. An MMS message is sent for video notifications when a thumbnail preview is part of the notification setup. Changes to the way T-Mobile, and now Sprint which was acquired by T-Mobile a few years ago, handle MMS delivery caused the recent change in the way video notifications were delivered to those customers. Again, this is something that is outside the control of Alarm.com.

A push notification is generated by an app. The Alarm.com app can generate a push notification for any notification that may be generated through your alarm system that is connected to Alarm.com. Here are a few examples of why Alarm.com believes Push Notifications are superior to SMS or MMS:

Alarm.com will soon unveil a Push Notification Migration Tool to steer customers toward using push notifications. You can check on the status of the tool rollout here. Not everyone will see the migration tool prompt. Being offered the prompt is based on the login used to access the Alarm.com app. At first, only a very specific group of customers will be targeted. That is customers with exactly one (1) SMS contact and one (1) push device on a network known to have had problems with SMS or MMS recently. This includes T-Mobile, Sprint, and Rogers (Canada) customers.

The full requirements are:

• The login must be the primary login.
• The login must not be linked to other systems.
• There must be exactly one enabled SMS/MMS contact address on the account and no other disabled SMS contact addresses.
• At least one enabled notification rule with an SMS recipient.
• There must only be one active push device on the account, and it must be the one the customer is using. Push notification rules need not already exist for that active push device.

When the tool is rolled out, customers who fit the parameters mentioned above will see a message like this:

As you can see, this is strictly a voluntary change. Users have the option to Migrate now, be reminded later, or never have the prompt come up again. If you use the migration tool and switch to push notifications, your SMS/MMS notifications will no longer be active. However, the SMS contact information will be retained in the address book.

At some point, the switch to push notifications may become mandatory, at least for some cellular customers. If it does, it will likely be due to changes undertaken by the cellular carrier that make the delivery of notifications less than optimal. If that occurs, we'll be sure to let you know about it here in our blog.

Intruducing the Qolsys IQ Heat 135 / 200. It offers a selection for the fixed alarm temperature limit of either 135°F or 200°F (57.2°C or 93.3°C). In addition, it has a rate-of-rise feature that activates an alarm if the temperature rises more than 12°F - 15°F (6.7°C - 8.3°C) per minute.

Qolsys is streamlining their products by combining the features of the Qolsys IQ Heat 135, and the Qolsys IQ Heat 200 into a single device. Using an internal jumper, the user can choose a fixed temperature alarm threshold of either 135°F (57.2°C) or 200°F (93.3°C). Based on this jumper setting, a temperature above the selected threshold will cause an alarm.

In addition to the fixed-temperature alarm threshold, the IQ Heat 135 / 200 also has a built-in rate-of-rise detector. If the ambient temperature rises from between 12°F - 15°F (6.7°C - 8.3°C) per minute, an alarm will occur.

Once either alarm threshold has been met, the IQ Heat 135 / 200 will use its transmitter to send an alarm signal to a compatible system. This includes any of the Qolsys IQ Panel 2, IQ Panel 2 Plus, IQ Panel 4, IQ4 Hub, IQ Hub, and IQ4 NS panels with a 319.5 MHz receiver built in. It can likely also be used with Interlogix/GE panels that support this frequency, such as the Simon panels, though we have not tested to confirm this.

The jumper used to set the fixed-temperature threshold has three (3) pins. If the jumper is across the LOW and center pin, the detector is set for 135°F (57.2°C) if the jumper is across the center and HI pin the detector is set for 200°F (93.3°C). If the jumper is removed completely, or lost, then the detector defaults to the high, or 200°F (93.3°C) setting.

The Qolsys IQ Heat 135 / 200 uses a single Panasonic CR123A 3V battery, and the expected battery life is about ten (10) years. Besides how often the detector transmits a signal, the biggest factor in battery life is ambient temperature. When the detector is mounted to the ceiling, the ceiling temperature should never exceed 100°F (37.8°C) under normal conditions. Just know that extreme temperatures, high or low, will likely affect the life expectancy of the battery.

The detector is fully supervised for RF check-in and transmits a signal to the system every 62 - 68 minutes. If the alarm panel doesn't hear from the sensor for a specified period, it will indicate a trouble condition on the zone associated with the IQ Heat. In addition to RF supervision, the detector is also supervised for tamper. If the heat detector is pulled away from the wall or ceiling, it will generate a tamper transmission to the alarm panel.

Specifications

• Device Type: Wireless Heat Detector
• Operating Frequency: 319.5MHz (crystal-controlled)
• Supervision Interval: 62 - 68 minutes
• Fixed Temperature Detection: Selectable 135°F (57°C) or 200°F (93°C)
• Rate of Rise Rating: 12° to 15°F (6.7° to 8.3°C) per minute
• Mounting Location: Ceiling or Wall
• Ceiling Mounting Specification: At least 4 in. (10cm) away from any walls
• Wall Mounting Height: Top of detector within 4 to 6 inches (10 to 15 cm) of the ceiling
• Standby Current: Less than 0.9μA
• Operating Temperature: 32°F to 150°F (0 to 65.6°C)
• Operating Relative Humidity: 0 to 95% noncondensing
• Batteries: One (1) Panasonic CR123A 3V (included)
• Expected Battery Life: 10 years (depends on how often the detector transmits signals, but is more dependent on the temperature of the installation environment. Warmer temps (within range) = longer life)
• Dimensions: 2.29" Diameter x 1.28" High (58.25mm Diameter x 32.4m High
• UL Max Ambient Ceiling Temp: 100°F/150°F (37.8°C/65.6°C)
• Maximum UL Spacing: 50ft (15.2M) x 50ft (15.2M)
• Agency Listings: UL 521 Heat Detectors for Fire Protective Signaling Systems, UL985 Household Fire Warning System Units, CAN/ULC-S530 Heat Actuated Fire Detectors for Fire Alarm Systems, CSFM Category 7270 - FCC: 15.109 Class B, 15.231, Industry Canada: ICES-003, RSS-210

FortrezZ is discontinuing another of its Z-Wave products due to its inability to source some required components. For this reason, Alarm.com no longer recommends its installation. Installed units will continue to work, and Alarm.com will continue to offer troubleshooting support for them.

This may be the result of the supply chain issues experienced a few years ago. FortrezZ was forced to discontinue the MIMOlite some time ago, and now we're seeing the discontinuation of their Water Valve. Products already purchased and/or installed are not affected by this news.

If you already have a FortrezZ Water Valve (WV-01) but haven't installed it yet, no worries. It should still install and operate as expected. If you have any problems related to integrating the water valve with Alarm.com, you can still get assistance from tech support. If you are an Alarm Grid monitoring customer, we offer free technical support as well.

If you were thinking of purchasing a FortrezZ Water Valve, but missed the opportunity, you have other options available. We offer the Alarm.com Z-Wave Plus Smart Water Valve and Meter, and the Alarm.com Z-Wave Plus Smart Water Valve. The Alarm.com smart water valves use Z-Wave Plus and can be used with any Alarm.com compatible panel that supports Z-Wave or Z-Wave Plus.

Left, Alarm.com Z-Wave Plus Smart Water Valve with Meter. Right, Alarm.com Z-Wave Plus Smart Water Valve:

In addition to the Alarm.com options, we also offer the Qolsys IQ Water Valve. It's available in two (2) separate kits. The PowerG Kit offers the IQ Water Valve with two (2) DSC PG9985 Flood Sensors. The S-Line Kit offers the water valve with three (3) Qolsys IQ Flood-S 319.5 MHz S-Line Flood Sensors. If purchasing one of these kits, be sure to take into account what panel the kit is meant to work with. All Qolsys IQ Panel 4 versions can support PowerG while only some can support 319.5 MHz S-Line sensors.

Below left, IQ Water Valve w/ Qolsys S-Line Flood Sensors. Right, IQ Water Valve w/ PowerG Flood Sensors:

A smart water valve is most advantageous when used in conjunction with flood sensors. If a water leak is detected by a sensor, it can alert the alarm system. Then, the system can use that information to run a rule or scene to automatically shut off the water main to the home or business. Having this type of protection can save on homeowner's insurance premiums, and can prevent widespread damage and loss to your home or business.

Specifications for Alarm.com ADC-SWM150:

• Device Type: Z-Wave Plus Smart Water Valve and Meter
• Power: 100-240VAC
• Operating Temperature: 14°F to 185°F
• Indoor/Outdoor: Indoor Use Only
• Valve Size: 1"
• Valve Threads: Male NPT
• Valve Portability: NSF/ANSI 61 and 372 Standards
• Control Unit Dimensions: 2.75"L x 4.0"W x 1.25"D
• Meter and Valve Dimensions: 11"L x 5.75"W x 3.75"D
• Actuator and Valve Dimensions: 2.0"L x 4.5"W x 3.75"D
• Maximum Compatible Pipe Size: 1.25"
• Power Supply Cable Length: 19.7 Feet
• Package Contents: Control Unit, Valve & Meter, Enclosure, Power Adapter, Manual Shut-Off Handle, Cable Ties (x5), Wall Bracket, Wall Anchors (x2), Screws (x2)

Specifications for Alarm.com ADC-SWV100:

• Power: 100 - 240 VAC (50/60 Hz)
• Operating Temperature: 14°F to 185°F (-10°C to 85°C)
• Communication: Z-Wave Plus
• Indoor/Outdoor: For indoor use only
• Valve Specifications:
  • Size: 1"
  • Threads: Female NPT
  • Potability: Conforms to NSF/ANSI 61 and 372 standards for potability
• Control Unit Dimensions: 2.75 x 4.0 x 1.25” (6.99 x 10.2 x 3.18 cm)
• Actuator and Valve Dimensions: 2.0 x 4.5 x 3.75” (5.08 x 11.43 x 9.53 cm)
• Maximum Compatible Pipe Size: 1.25" (3.175 cm)
• Power Supply Cable Length: 19.7’ (6 m)
• Plumbing Certifications:
  • ICC-ES-PMG (compliance with NSF 61 and NSF 372)
  • Massachusetts Accepted Plumbing Products Registry

Specifications for Qolsys IQ Water Valve:

• Product Type: Smart Water Valve
• Kit Contents: Qolsys IQ Smart Water Valve, Qolsys IQ Flood-S Sensor
• Communication: Z-Wave Plus V2 700-Series
• Range: Approx. 130 Feet Indoors or 450 Feet Outdoors
• Application: Quarter-Turn Ball Valve Pipes from 1/2" to 1-1/4"
• Maximum Force: 8 N.m
• Ingress Protection: IP66 (Waterproof & Dustproof)
• Power Supply: Plug-in Transformer - AC (110V 60Hz / 220V 50Hz), DC (12V/1A) - Barrel jack
• Weight: 603g (21.2 oz)
• Size: 5.83" x 3.78" x 5.24" (148mm x 96mm x 133mm)
• Operating Temperature: 14°F to 121°F (-10℃ to 49.4℃)

Specifications for DSC PG9985 Flood Sensor:

• Device Type: Wireless Flood Sensor
• Operating Frequency: PowerG 915 MHz
• Wireless Range: ~2,000 Feet Open Air
• Water Detection Probe: Attached w/ 6-Foot Cord
• Batteries: Single CR123A (~8 Year Life)
• Mounting Hardware: Double-Sided Foam Tape (Included)
• Dimensions: 3.1875" x 1.25" x 1.0" (81mm x 34mm x 25mm)
• Operating Temperature: 14°F to 122°F (-10℃ to 50℃)
• Weight: 53g (1.9oz)

Specifications for Qolsys IQ Flood-S Flood Sensor:

• Device Type: Wireless Flood Sensor
• Operating Frequency: 319.5 MHz
• Wireless Range: ~600 Nominal Feet
• Water Detection Probe: Attached w/ 6-Foot Cord
• Signal Outputs: Tamper & Tamper Restore, Alarm & Alarm Restore, Low-Battery
• Supervisory Interval: 70 Minutes
• Batteries: Two (2) Lithium CR2032 Coin Batteries
• Mounting Hardware: Double-Sided Foam Tape (Included)
• Dimensions: 2.5"L x 1"W x 0.5"D (64mm x 25mm x 13mm)
• Operating Temperature: 14°F to 122°F (-10℃ to 50℃)

In addition to the options listed above, there is also the Honeywell/Resideo 5821 that can be used in conjunction with the FP280 flood probe. This sensor will work with any of the Qolsys IQ4 panels that support 345 MHz RF devices. A panel with one or more of these sensors can be used to automate any of the water valves listed in this post.

What are your thoughts on the discontinuation of another FortrezZ Z-Wave device? Have you encountered similar issues with other products? Drop us a comment and let us hear from you. If you have a specific support question, you can send us an email to support@alarmgrid.com. We're here providing support Monday - Friday from 9:00 am until at least 6:00 pm Eastern Time each day. We list holiday hours and closings in our blog.

If you're shopping for electronic security, Z-Wave, or other low-voltage equipment, and you find a product that you love, that Alarm Grid doesn't currently offer, submit this form so we can list it. Send us an email to support@alarmgrid.com to let us know, and we'll expedite the listing.

We may not be able to source every product you run across, but if we can, we'll gladly list lifestyle and security-related products on our site. If you're designing a system and you need the product within a specific time frame, send us an email to let us know and we'll get the item listed as quickly as possible.

On our New Product Form, we ask for certain information. Below, we'll list each piece of information and a brief explanation of what we're looking for in each:

Product Title (Required):

This is like a Make and Model, or Manufacturer and Model Number. Provide as much identifying information as you can, particularly if different models are very similar and you require a specific one. We may add more than one model, but we want to add the one you're looking for first.

Product SKU (Required):

An SKU stands for Stock Keeping Unit. It helps both manufacturers and retailers keep track of product stock and also helps to make sure that when you inquire about apples, we don't give you oranges instead. For us, it is very important, but may not always be apparent when you're shopping for a product.

Below is an image taken from the Alarm Grid storefront on Amazon.com. As you can see from the listing, there is no SKU specifically called out. But, we happen to know that the SKU for this product is PROLTE-A. So, if you're attempting to provide us with information on a product, and you can't find an SKU, list the model number again (as the SKU is required on the form). We'll do our best to find the correct product with the information provided and may reach out via email to make sure we have the correct item.

Help Us Source It (Optional):

Where were you shopping when you saw this item? Was there a particular website? Provide as much information as you can on where this product can be found.

Approximate Sales Price (Optional):

What is the price you've seen for this product elsewhere? You may think we only ask this so we can charge as much as possible for the product, but that's not the case. Alarm Grid is not a wholesale distributor, and as such, other wholesalers and dealers may have a price for an item that we can't match (and we don't price match).

If we find that's the case, we'll be honest with you about it. We may still list the product on our site, but we won't hold you up if you're waiting for us to list it, only to find that our price is higher than you expect.

Please Describe the Item's Function In a Paragraph (Optional):

Yes, there's homework, though we're not asking for a full book report. Just give us a brief description of what this item is used for. You can even tell us what you want to use it for. This helps us in a couple of ways. It gives us a good understanding of why the product is useful, and it also allows us to be sure that the item will do what you want it to do. If not, we may be able to recommend a different item that will work better.

Please Describe Why You Believe Alarm Grid Should Sell This Product (Optional):

This can be as simple as "Because it's new and you don't offer it yet." Just give your thoughts about the product.

What Is Your Name? (Optional):

This is not a required field, but if you do send us an email to expedite the addition of the recommended product to our site, it will help us tie that email to this request.

Email (Optional):

Once again, this is not required but will help us if we have questions about the product. Particularly, if you're not able to provide an accurate SKU. If we can't properly source the product, and we don't have an email to contact you, then we may have to abandon the attempt to offer it on our site.

So, that's how you can request that a new product be added to the Alarm Grid website. We can sometimes get a product listed on the same day, depending on what time we receive the request and an email asking us to expedite the listing. Just don't forget to follow up on high-priority requests with an email letting us know you're waiting for the product to be available.

UPDATE 3:00 PM EST 02/22/24:

The nationwide AT&T outage has been resolved and all affected users, including alarm communicators, have been restored to normal operation. AT&T is still investigating the cause of the outage, and no concrete information is yet available. If a forensic analysis is made public, we will comment on it in a separate post.

Both AlarmNet and Alarm.com show that service for customers with AT&T communicators has been fully restored. If you have an AT&T communicator that still seems to be offline, attempt to power cycle the device.

Always put a monitored system on test with the monitoring station before performing any kind of maintenance.

For most stand-alone communicators, you can do this by unplugging the battery and the primary power supply, waiting about 30 seconds, and then powering back on by plugging the battery, and then the power supply back in. If your communicator gets its power from a VISTA alarm panel, like the LTEM-XA, then power cycle the entire system. Power down by unplugging the panel's battery and transformer. Power up by plugging in the transformer first, and then the battery.

For older All-in-One systems, like the LynxTouch panels, you'll need to power cycle the entire system. Do this by opening the panel and unplugging the battery, then unplugging the transformer. When powering back up, plug the battery in first, then the transformer.

The PROA7 and PROA7PLUS panels have a reboot option through the Tools Menu. From the Home Screen, tap Menu (≡) > scroll down, tap Tools > Enter Installer Code (4112 by default) > scroll down and tap Reboot.

If you have a Qolsys touchscreen system, be sure to go through the panel's menu to reboot, rather than removing the battery and DC power. Not following the proper power-down or reboot procedure can damage the panel. Tap the gray bar at the top of the screen, then tap Settings > Advanced Settings > Enter Installer or Dealer Code (1111 or 2222 respectively, by default) > Panel Reboot (↻).

ORIGINAL POST:

A nationwide outage, beginning this morning at approximately 3:30 AM, is affecting both mobile phones and alarm communicators. The outage seems to be limited to AT&T, though there were early reports of issues with T-Mobile also. According to T-Mobile, their service is working normally now.

AlarmNet has posted this notice on the AlarmNet360 page:

Alarm.com has posted this notice:

It is important to note that this is a carrier outage, not an AlarmNet, Total Connect 2.0, or Alarm.com outage, meaning this is not something Resideo or Alarm.com can resolve. As new information becomes available, we will update it here. As an AT&T Subscriber in the Louisville, KY area, I can report that I have no cellular service at this time. AT&T recommends that their wireless users take advantage of WIFI calling wherever possible, until this issue is resolved.

This outage does potentially affect your ability to remotely control your system, to receive notifications from your system, and your system's ability to report alarm and other signals to a central station, but only if you have an AT&T communicator tied to the system or have an AT&T Mobile Device and no access to WIFI. To our knowledge, Verizon communicators are unaffected.

If your system reports a trouble condition related to the cellular outage, you can silence any audible alert by acknowledging the trouble condition. For users with touchscreen panels, this will usually involve touching the notification message and then acknowledging it on the next screen.

For VISTA users, a disarm command should be entered. This is accomplished by entering a valid 4-digit user code, and then pressing the 1 or OFF key. Once the outage has been restored, you will need to perform a disarm command again to clear the trouble condition from the display.

Most wired DSC panels indicate a trouble condition by displaying a triangle with an exclamation point inside. Pressing [*] [2] and then viewing the number or numbers displayed will explain what the condition is. A four usually (4) indicates a Comm Failure. You can see information about how to view DSC trouble conditions here. DSC Impassa users can see the Install Guide here. Information about trouble codes is on page 72. You can see a DSC PowerSeries troubleshooting guide here.

02/14/24 1:09 PM UPDATE: Per Resideo, these two issues are unrelated. However, the second issue, involving AT&T communicators appears to have been resolved.

02/13/24 4:15 PM UPDATE: Resideo has an update on the AlarmNet360 site currently:

"A small percentage of ProSeries and LTEMP LTE AT&T communicators may experience signaling issues that could result in a communication failure message being generated to the monitoring Central Station.

This issue is being worked with AT&T for immediate resolution.

We appreciate your patience while we work to quickly resolve this issue."

It is not clear whether this is a separate issue, or is related to the Pro Series issue originally reported in this post. When we get that information, we will either update here or in a new post with details of the new issue. Keep watching this space for updates.

02/13/24 Original Post:

Recently, Resideo identified an issue with select PROA7 and PROA7PLUS panels: screens become dark/unresponsive, losing connection to AlarmNet. A hard reboot is required for a reset. Resideo plans a firmware upgrade to address this, which will be applied automatically to all Pro Series panels.

This alert applies to all Resideo and Honeywell Home Pro Series panels. This includes the PROA7, PROA7C, PROA7PLUS, and PROA7PLUSC. While they say the number of affected panels is very small, we don't yet have an actual number or a date code range to confirm those details.

In response to this issue, Resideo has a firmware update, 03.1872.18.0 which they will begin pushing to all registered Pro Series panels this week. The update will also be available to dealers to push manually beginning on 02/13/24. This is a critical update and will be pushed over WIFI, if available, or Cell if WIFI is unavailable. It is important to note that only registered panels can receive this firmware update. Registered means that there is an account associated with the panel.

An affected panel will be dark, with no status LEDs illuminated. Along with these visible symptoms, the panel will stop communicating with the AlarmNet servers. This will eventually generate a report to the monitoring station of E359, which indicates the panel failed a regularly scheduled check-in.

If you have a Pro Series panel and believe your panel is affected, we recommend you power cycle it as soon as possible. Remove the set screw in the bottom of the panel and pull the front and back of the panel apart. Doing this will automatically remove the primary DC power.

Next, find the panel's battery and unplug it from the main board. Leave it disconnected for about 30 seconds, then plug it back in. Now carefully put the panel back together. Doing so will reconnect the primary power and the panel should begin to boot up. Replace the set screw, if installed and allow the panel to boot. This should return the panel to normal operation and allow it to receive the firmware update.

Panels that receive the firmware update will reboot as a part of the update process. This will generate a signal to the monitoring station of E-339-Exp. Module Power On / Reset, or possibly E-305-System reset, or possibly both.

If we receive further details on this issue, we'll post them here, so stay tuned. Updates will be posted near the top of this page and will be highlighted with a bold date and wording to indicate new information. We have yet to receive an official MWT Technical Bulletin on this issue, but I believe one is likely coming soon. Hopefully, it will contain the details that are, so far, notably missing.

Update 02/06/24:

Per Resideo, they first began seeing this issue back in April 2023. They were able to determine that the Total Connect 2.0 server was creating and sending the notifications properly. They checked with the receiving carrier, in this case, Telus, and found that Telus had blacklisted TotalConnect2.0@alarmnet.com as SPAM. Therefore Telus was not delivering these notifications. This will affect SMS and Email notifications only.

For those Canadian customers who have complained of this issue, contacting Telus and asking them to whitelist totalconnect2.0@alarmnet.com has resolved the issue. This will also affect Canadian users of the Rogers service. Both Telus and Rogers appear to use the same intermediate SMS provider.

Original Post:

Alarm Grid has had reports from our Canadian customers that they are not receiving notifications from Total Connect 2.0. After checking with Resideo, we have confirmed there is an issue, and they are currently working with Telus to resolve it. We don't have an ETR. Check back for updates.

This is a recent development, though we haven't received any details from Resideo yet as to when the issue began. It seems to affect text, email, and push notifications to recipients in Canada. When we have more details, we will provide updates here. Rest assured this does not affect your system's ability to send alarm signals. Any signals generated by your system will be processed normally.

Alarm Grid and Alarm.com customers in Ameren, IL can sign up for the Peak Time Savings Program. Once enrolled, you will receive a $50 e-gift card. For each subsequent year you remain enrolled, you will receive a $25 e-gift card. This is another way your smart thermostat can pay for itself.

We've written about the Give Back, Get Back program numerous times in the past. Many different utility companies offer a similar incentive program, and each company has its name for the program. Some offer rebates, others may offer bill credits. The incentive amounts also vary. The information included here is specific to the Ameren, IL program.

To qualify for this incentive, you just need the following:

• Be a residential electric customer in Ameren, IL, with service in your name.
• Use an internet-connected, qualifying smart thermostat.
• Sign up for the program, which allows the Ameren, IL electric company to make small adjustments to your thermostat remotely, during peak usage times.
• You must not already be participating in a demand response program.

The times when your thermostat is likely to be adjusted are during the hottest days of summer when power demands are at their greatest. This can cause strain on the electrical grid. By signing up for the Peak Time Savings Program, you agree that the electric company can make small adjustments of four (4) degrees or less during these times. These adjustments will last for no more than four (4) hours.

The most likely hours during which an adjustment may occur are between 1:00 p.m. and 7:00 p.m. CT, but adjustments could occur anywhere from 6:00 a.m. to 10:00 p.m. CT. You retain control of your thermostat and can opt out of an adjustment event at any time. In some cases, the thermostat may briefly be adjusted down (cooler) before being adjusted up (conservation) to maintain comfort during the adjustment period.

The thermostats that are compatible through Alarm.com are:

• Trane ComfortLink Control
• RCS Z-Wave Communicating Thermostat
• GoControl Z-wave Thermostat
• Alarm.com Smart Thermostat
• 2GIG Z-Wave Plus™ Battery Powered Thermostat
• Trane Z-Wave Thermostat
• Linear Thermostat
• Smart Thermostat HD (ADC T40K-HD)
• ADC T3000
• ADC T2000

You can sign up for the program by going to this page, and then clicking the link "Enroll Your Smart Thermostat." Once you are accepted, you should receive an email within 60 days of being accepted. The $50 e-gift card will be delivered to your email, so be sure when you sign up, you enter the correct email information.

If you remain enrolled in the program, on the anniversary of your enrollment, you will receive a $25 e-gift card via email for your continued participation. This will occur each subsequent year you remain enrolled. Currently, there is no end date, so this incentive will continue until you are notified otherwise.

It's the middle of winter, but summer will be here before you know it. If you've been on the fence about purchasing a smart thermostat, this may be the perfect time to commit. Signing up for a program like this may seem like a small step, but as they say, the journey of a thousand miles begins with the first step and every step brings you closer to your goal. In this case, the goal is energy conservation, and every little step helps.

For many proprietary panels, the settings that determine where signals are sent are hardcoded. That means, if a customer decides they want to change alarm companies, they have to replace their system, and in some cases, all of their sensors. Alarm Grid does not sell proprietary systems.

There are many different ways in which alarm companies retain their customers. Some use cheap up-front pricing with long contracts for monitoring services. Others use completely proprietary systems, with the alarm panel and all sensors being useless unless they are used with the original company's monitoring service. At Alarm Grid, we retain our customers by providing equipment at a fair price, and excellent customer service.

The "Low Up-Front Cost" System:

You're probably familiar with many of the alarm companies that use, or have used, proprietary equipment. Names like ADT, Moni (formerly Monitronics), Vivint, and Xfinity have all used proprietary systems in the past, and I'm sure there are more. They were successful in this because in most cases, they were providing the equipment free, or at a reduced rate with very inexpensive installation.

In exchange, the customer would be required to sign an expensive, multi-year monitoring contract. Monthly monitoring is where they make up the money lost on equipment and installation. In most cases, these companies design the system and have it manufactured in such a way that the account information, the information that identifies which system this is, can't be changed. This ensures that if the customer wants to continue using the equipment, they have to continue paying the monthly fees.

The good news about these systems is that in most cases, it is possible to reuse the equipment with a new company. You may have to replace the communicator, and in some cases, you may even have to replace the main system, but the sensors can usually be reused.

The "Completely Proprietary" System:

In other instances, a company may sell and install a completely proprietary system. With these systems, not only is the information about where the system sends its signals pre-defined, but any wireless sensors used to protect the premises are also proprietary. So, if you decide to switch to a different monitoring company, you'll have to replace not just the main panel and communicator, but every sensor too.

When this type of system is used, the company will often tout the fact that they have no long-term contract for monitoring. But, how many customers are willing, or able for that matter, to replace their entire system if they are unhappy with their service after a few months?

Unfortunately, with this type of system, to switch to a new monitoring company everything will usually need to be replaced. Recently, some progress has been made by professional security equipment manufacturers being able to work with these sensors. Qolsys now has a Zigbee daughter card that can be installed with the IQ4 panels. This allows the Qolsys IQ4 panels to work with some once-proprietary sensors. You can see a list of compatible Zigbee Automation and Security Sensors here.

The "Alarm Grid Way":

At Alarm Grid, we're in this business to help home and business owners de-mystify the installation and use of alarm systems. For years, many of us have worked within the industry and were frustrated by its practices. The alarm industry is modeled after the automobile industry. A manufacturer sells equipment to dealers, the dealers sell to end-users and it is up to the dealer to support and service their customers.

The alarm dealer is the manufacturer's customer, and the end-user is the alarm dealer's customer. Therefore, an end-user can not get any support from the manufacturer, they have to go through their dealer. This is a great setup, as long as your alarm dealer is competent, responsive, and promptly returns your calls, texts, or emails.

The problem is, that's not always the case, and when it's not, what is a customer to do? They can't get assistance from the manufacturer. So, we help them. We provide hundreds, if not thousands of FAQ articles on our site that outline how to install, program, and service alarm systems and equipment from Honeywell/Resideo, Qolsys, 2GIG, Interlogix, DSC, and others. We provide this information freely to anyone who can use it.

For many of these FAQs, we also offer companion YouTube videos. For our monitored customers, we provide free one-on-one technical support through phone calls, email, and chat. We sell alarm equipment, but we don't push anyone to buy from us. If you're our monitored customer, we'll support you no matter where you purchase your equipment. We'll also do everything we can to be sure you can use as much of your existing equipment as possible.

At Alarm Grid, we don't require contracts for our monitored customers. All of our plans are month-to-month and you can cancel at any time. We believe in retaining customers based on providing superior service, not because of a contractual obligation or a gimmicky system that only works if you use our service. That's the Alarm Grid way.

Alarm.com recently announced that due to some network changes undertaken by T-Mobile, those customers who currently receive MMS (Multi-Media Messaging Service) notifications with video clips and thumbnails, will soon begin receiving SMS (Short Message Service) messages with links instead.

This only affects Alarm.com customers who use T-Mobile for their mobile phone service. Currently, the change is set to go into effect on January 31, 2024. Those customers who use both Alarm.com and T-Mobile who are on iOS devices with the latest software may not notice a change, as those devices will automatically open the links to offer a preview. However, for customers on Android devices, or iOS devices that are not updated this change will likely be readily apparent.

Alarm.com supports Push Notifications through the Alarm.com app, and they encourage the enabling of Push Notifications for all Alarm.com customers who use smart devices to receive notifications. They are taking steps to minimize the use of MMS messaging regardless of carrier. Those steps are as follows:

• T-Mobile Customers: As already mentioned, with the changes at T-Mobile, those customers will begin receiving SMS, instead of MMS, messages at the end of January. In these messages, they will receive links to thumbnails and clips, rather than the clip or thumbnail being embedded in the message. Users on updated iOS devices may not notice this change as these devices will open the links automatically. For users with other devices, such as Android phones, the change will be more noticeable.
• UI Updates. Over the next several months, Alarm.com plans to roll out expanded messaging options within their user interfaces to make Push Notifications the more attractive option for customers. They plan to release new tools that will make the use of Push Notifications even easier to set up and use.

As we mentioned before, Alarm.com strongly recommends that customers use Push Notifications instead of SMS or MMS messaging. There are several advantages to this, including:

1. In Push Notifications, users are redirected to live or saved clips, depending on whether the clip has been uploaded yet. This allows them to access their content quickly.
2. Users can pause notifications directly from Push Notifications.
3. Push Notifications offer unique doorbell sound effects.
4. As iOS and Android devices continue to evolve, Alarm.com will continue to enhance the features of Push Notifications.

Alarm.com customers who use T-Mobile phone service need not do anything. These changes will take effect automatically at the end of January, 2024. You can read about the different types of customer notifications here. For help setting up Push Notifications, you can read this article.

If you're both an Alarm.com and a T-Mobile customer, we'd love to hear your thoughts on these changes. Give us your opinion on the new format. Do you use Push Notifications, with SMS or MMS as a backup? Does this change your feelings about either Alarm.com or T-Mobile? Start a conversation in the comments below.