Honeywell SiX Smoke Detectors Posts

Alarm Grid is happy to announce that the Honeywell Home PROSIXRPTR Wireless Repeater is now available for purchase. The wireless repeater works with Honeywell Home and Resideo PROSIX Sensors and Honeywell SiX Sensors used with the ProSeries Security Panels, including the PROA7PLUS.

If you aren't familiar with wireless repeaters, these devices effectively double the range of compatible wireless sensors. This works by taking the wireless signal sent out from a wireless sensor and sending it out a second time, thereby effectively repeating the signal and doubling the sensor's range, assuming that the repeater module is placed strategically. The PROSIXRPTR is the first wireless repeater released from Resideo since the Honeywell 5800RP Wireless Repeater which is used to repeat the wireless signals of Honeywell 5800 Sensors. The new PROSIXRPTR is also the first-ever encrypted wireless repeater released by Resideo. Up to two (2) PROSIXRPTR devices can be used with a ProSeries System, with each repeater being placed in a different direction from a centralized ProSeries Panel.

There's a lot to take in with the PROSIXRPTR, so we'll do our best to cover everything here. The first thing we want to note is that the PROSIXRPTR is not a "plug-and-play" device, as you may be accustomed to with most wireless repeaters. In other words, the PROSIXRPTR will not begin repeating wireless signals until it is enrolled with a ProSeries Panel. These panels include the aforementioned PROA7PLUS, the Resideo PROA7PLUSC, the Resideo PROA7C, and the Honeywell Home PROA7. Any ProSeries Alarm System in need of a PROSIXRPTR Wireless Repeater must be on at least Firmware Version 3.591.92.0, which you can read about in greater detail here. The reason why the PROSIXRPTR needs to be enrolled with the alarm panel is because it is interacting with encrypted signals, and it needs to know sensitive network information to do its job successfully. Although you can have two (2) different PROSIXRPTR modules paired with a single ProSeries Panel, the two units will not communicate or "talk with" each other in anyway, and you cannot use a "series" setup to "triple" the range by having a sensor signal bounce off of one PROSIXRPTR to another PROSIXRPTR on its way to the panel. The PROSIX or SiX wireless signal will only be recognized by a single PROSIXRPTR, it will get repeated once, and will then end up at the ProSeries alarm panel.

There are other limitations affecting the PROSIXRPTR Repeater that should be discussed. While the unit can repeat SiX Sensors used with a ProSeries Alarm Panel on a high enough firmware version, the PROSIXRPTR cannot repeat the signals for SiX Series Sensors used on a Honeywell Lyric Security System. Remember, the PROSIXRPTR must enroll with the panel it is being used with. The unit has no way of integrating with the Lyric, and it cannot repeat wireless SiX Series signals used with that system. Unfortunately, Resideo never released a repeater for the Lyric and SiX Sensors, so that is just a limitation that Lyric users will have to live with, at least for now. The PROSIXRPTR also cannot repeat the signals of any legacy sensors that are being used with the Honeywell Home PROTAKEOVER Module. There are various legacy wireless repeaters available, so please reach out to us at support@alarmgrid.com during our usual 9am to 8pm ET M-F business hours if you need help figuring out which one to get for your alarm system.

One other thing we want to note with the PROSIXRPTR is that while it comes with its own transformer and backup battery, it does not come with any cabling for connecting the transformer. Make sure you have some around when you go to set it up. The unit supports a wire run of up to fifty (50) feet (~15.2 meters) when using 18 AWG cabling, and the maximum distance goes down if thinner cabling is used, so make sure to observe the permitted wire runs. Alarm Grid offers alarm wiring on its website if you need some. We even offer 10 ft., 15 ft., and 25 ft., pre-cut lengths of 22 gauge, 4-conductor wire. Or, you should be able to find some at your local hardware store. You can also use a Honeywell LT-Cable if you don't want to prepare your own wiring.

The PROSIXRPTR can be purchased on our website now! Please email us if you have any questions. Also, don't forget to leave a comment down below to share your thoughts on this new unit. We would love to hear what you have to say. And of course, keep paying close attention to the Alarm Grid Blog if you want to hear the latest security news, tips, and product releases. We'll be back soon, so stay posted!

If you're using a newer wireless security system, then you will definitely want to explore the encrypted sensor options that we offer! Encrypted sensors are virtually impossible to hack, and they can make your security system even more secure. There are many great options available.

As you know, a home security system or a business security system is an investment you make for the protection of yourself, your property, and those around you. A proper system should also give you peace of mind and make you feel safe. It doesn't do you any good if an intruder manages to defeat your system. But with encrypted sensors, that is extremely unlikely to ever happen.

If you aren't familiar with encryption, it refers to techniques for encoding data and signals so that only authorized individuals and/or equipment are able to access the information. When it comes to wireless alarm systems, encrypted sensors send protected signals that can only be accessed, received, and interpreted by the authorized panel.

When wireless systems first rose to prominence, they rarely, if ever, used encryption. This made many people wary of wireless security panels, and they felt more secure using wired ones. The lack of encryption wasn't seen as a fatal flaw, as an intruder would have to be extremely savvy and really know what they're doing to defeat even a non-encrypted sensor. To this day, many people feel totally comfortable and safe using non-encrypted equipment. Remember, most intruders don't have the knowledge to beat wireless sensors, even if they aren't using encryption.

But there are the rare, professional criminals who do take the time to extensively study security equipment, and they develop techniques for beating non-encrypted devices. This is very uncommon, but it's not unheard of. And if you aren't using encrypted sensors, then you are leaving yourself open to this small risk. Whether or not that means outfitting your system with all-new encrypted sensors, or even upgrading to a different system that is capable of supporting encrypted sensors is up to you. We just want to make you aware of your options.

Today, we're going to briefly look at some popular wireless systems and explore their encrypted sensor options, as well as their non-encrypted sensor lineups. This will help you learn more about your system, or one you are considering for purchase.

Honeywell Lyric Controller

The Lyric represents the first the first encrypted panel from Resideo, formerly known as Honeywell. The system has its very own lineup of encrypted sensors called the Honeywell SiX Series Sensors. The lineup is a bit limited, as its lacking options like an outdoor door and window sensor and a curtain motion sensor. But the good news is that these sensors are extremely secure with their military grade 128-bit AES encryption.

You can supplement your SiX Series Sensors on your Lyric System with devices from the Honeywell 5800 Series. These sensors are not encrypted, but the lineup offers more diverse selection than the SiX Series lineup. You could consider using encrypted sensors for the most vulnerable parts of your home or office, while using non-encrypted 5800 Series devices for areas where it isn't as important. The non-encrypted 2GIG 345 MHz Sensors are also compatible with the Lyric once the system is on Firmware Version MR3 or higher.

Qolsys IQ Panel 2 Plus

There are some outstanding encryption options available for the Qolsys IQ Panel 2 Plus, regardless of which version you have. Any IQ Panel 2 Plus System can readily support DSC PowerG Sensors. Not only do these sensors have an outstanding wireless range of up to 2,000 feet away from the IQ Panel 2 Plus, they also utilize military grade 128-bit AES encryption and Frequency Hopping Spread Spectrum (FHSS) technology.

And if you have the 319.5 MHz Version of the Qolsys IQ Panel 2 Plus, then you can also pair Qolsys S-Line Sensors, which use rolling code encryption. This rolling code encryption isn't quite as secure as the encryption used by PowerG Sensors, but it still does a good job of keeping your system protected. The S-Line Sensors will also utilize encryption when paired with the original Qolsys IQ Panel 2. The original IQ Panel 2 cannot use PowerG Sensors.

In terms of non-encrypted options, each IQ Panel 2 Plus can support one of three (3) non-encrypted radio frequency signals. The available options are 319.5 MHz, 345 MHz, and 433 MHz, and it is dependent upon which version of the IQ Panel 2 Plus you buy. Again, it is certainly possible to mix encrypted sensors with non-encrypted sensors on the same system. But with the diversity and selection of the PowerG lineup, you probably won't need to look outside too much.

2GIG GC3e

The big highlight when the 2GIG GC3e was introduced was its ability to support encrypted sensors. While it took a little while before its encrypted sensor lineup became available, we were very pleased with the result. The 2GIG eSeries Sensors use highly secure encryption to keep your system protected. It also seems that 2GIG is regularly expanding upon this lineup, as we have been seeing new eSeries Sensors hit the market it recent times. All of the 2GIG eSeries Sensors are compatible with the GC3e, as well as its little brother, the GC2e.

With the GC3e, you also get access to the Honeywell 5800 Sensors and the 2GIG 345 MHz lineup. Just like with the Lyric, there is a bit more of a diverse selection of non-encrypted sensors available for the 2GIG GC3e. You can definitely set up a mixture of encrypted and non-encrypted sensors to meet the needs of your business. But with new 2GIG eSeries offerings continuing to become available, you shouldn't have much trouble building a fully encrypted 2GIG Security System.

If you are looking to set up an encrypted security system, then Alarm Grid is here to help! We can let you know if your existing system has any encrypted sensor options available. We can also help you determine if you are currently using encrypted devices or if your existing sensors are non-encrypted. Many users have trouble determining. Either way, we'll help you make an informed decision so that you can get the most out of your monitoring service. If you want to reach us, please email support@alarmgrid.com. We check our email from 9am to 8pm ET M-F. We look forward to hearing from you!

Hi DIYers! Today, we're taking a look at why one-go-all-go smoke detectors can help ensure that everyone in the building is alerted during a fire. Simply put, a one-go-all-go smoke detector will cause all of the other compatible smoke detectors on the system to activate at the same time.

Having all the smokes in your home activate at the same time can be crucial for ensuring that everyone is alerted in the event of a fire. This is especially true for larger homes that need several smoke detectors for complete coverage. Most alarm systems can have some type of interconnected one-go-all-go smoke detector network. However, implementing this feature properly can be difficult, and it requires additional equipment and wiring. Another important thing to remember is that the one-go-all-go feature is best achieved by using the same detector model across the network.

For those with wired alarm control panels, there is often a way to achieve a one-go-all-go setup using hardwired smokes. This is possible with both 2-wire smokes and 4-wire smokes, but both require the proper equipment. Many wired panels offer a way to conveniently reset the zone used for 2-wire smokes after a fire alarm has been cleared. This is needed for getting the smoke detectors to stop sounding and to reset the detector so that it can trip again, if necessary.

For the Honeywell VISTA Panels, all 2-wire smokes must go on zone 1. This zone will automatically reset, and power will be briefly dropped to the smokes after the alarm is cleared. Multiple 2-wire smokes are wired together in parallel, with an end of line resistor (EOLR) for wiring supervision. A good 2-wire smoke detector to use is the System Sensor 2WTA-B, which also includes a built-in sounder.

Unlike 2-wire smokes, 4-wire smokes have less restriction regarding where they can be wired. In fact, a 4-wire smoke on a Honeywell VISTA System will generally go on any hardwired zone, except for zone 1. Again, the smokes can be configured for a one-go-all-go setup, but this will require additional equipment and wiring. This also allows the smokes to take up fewer systems zones, as they can all use the same zone and programming settings.

One downside to using 4-wire smokes is that they often require additional resources to work properly. In order to get a 4-wire smoke to stop sounding, power to the device must be dropped. But unless the system has a built-in relay, this cannot be done without additional hardware. This can require an external relay, and possibly an additional power supply as well. Proper operation will also require an end-of-line power supervision relay to check whether or not power to the smokes has been interrupted. If you do decide to go the 4-wire route, the System Sensor 4WTA-B is a good option.

More recently, certain wireless smoke detectors also offer one-go-all-go functionality. Honeywell really took the initiative here by making their Lyric SiXSMOKE Sensor a one-go-all-go device. This sensor is exclusively compatible with the Honeywell Lyric Alarm System, and provides a very easy way to achieve a robust one-go-all-go setup. One-go-all-go is also compatible with the new Honeywell SiXCOMBO, which also offers heat and CO detection.

If you have a different wireless system than the Lyric, then there might still be way to attain a one-go-all-go setup. In most cases, this will require using 4-wire smokes with a compatible wireless transmitter. The transmitter will need to be able to support Normally Open (NO) life-safety devices with an end of line resistor. However, this is not possible for every wired-to-wireless converter.

Additionally the standard equipment for any 4-wire smoke is also required. This includes a relay, power supply and resistor. One transmitter that will work for this application is the Honeywell 5817CBXT. This module is part of the Honeywell 5800 Series, and it will work with nearly any alarm system that accepts the 345 MHz wireless frequency. Remember, the transmitter or converter must communicate at a frequency accepted by the alarm control panel.

Additionally, Qolsys recently released the Qolsys IQ Hardwire 16-F for 319.5 MHz systems. This is a 16-zone wired to wireless converter that is great for bringing over hardwired sensors to a newer wireless system. Zone 16 on the module is a Normally Open loop specifically designed for 2-wire smokes. The loop will support up to ten 2-wire smoke devices, which are wired in parallel with an end-of-line resistor. This revolutionary module represents the first way to bring 2-wire smokes over to a wireless all-in-one system. The necessary resistors come included with the module.

Additionally, if you have an existing network of high-voltage smokes, you can integrate them into a wireless system using a takeover module. These are devices that listen for the unique temporal sound of an activated smoke detector. If the existing smoke detector network is one-go-all-go, a single takeover module can accommodate the entire network. Alarm Grid offers takeover modules that operate at the 319.5 MHz (Interlogix/GE and Qolsys), 345 MHz (Honeywell and 2GIG) and 433 MHz (DSC) wireless frequencies. That way, you can conveniently take an exiting high-voltage smoke network and start using it with your new wireless security system!

If you need help choosing smoke detectors for a one-go-all-go setup, please don't hesitate to reach out to us! We can help you determine the perfect fire-protection devices for your security system. You can send an email to support@alarmgrid.com, or you can call us at (888) 818-7728 during our normal business hours of 9am to 8pm EST M-F. We look forward to hearing from you!