Encrypted Wireless Motion Sensor Posts

One thing we have noticed about the 2GIG GC3e is that it seems to be prone to erroneous Supervision Trouble conditions. This has left some users confused as to why their system zones are not working properly. But luckily, we have some tips to prevent this from happening to you and your GC3e.

Before we give our three (3) tips to follow, let's make sure we're all on the same page by explaining what Supervision Trouble normally refers to. Supervision Trouble occurs when a system does not receive a periodic "check-in" signal from an enrolled wireless sensor. This is usually either the result of the sensor not being able to send out its check-in signal, or the check-in signal not reaching the intended destination of the alarm panel. Some reasons why the sensor might not send out the signal include the sensor being powered down due to a dead or removed battery, or the sensor being physically destroyed. Some reasons why the the sensor's wireless check-in signal might not reach the alarm panel could include the sensor being moved to a new location in the building, or new obstacles, such as thick walls or large metal structures, being added inside the building. Regardless of the cause, you need to make it so that the sensor's check-in signals successfully reach the panel. Once you do that, you can clear the trouble condition. For GC3e users, you can learn how to clear the trouble condition by reviewing this FAQ.

But for the 2GIG GC3e, we have seen Supervision Trouble conditions occur, even when the sensor is powered on, successfully enrolled, and in clear communication range of the alarm panel. The issue seems to be particularly prevalent for the encrypted 2GIG eSeries Sensors that were built specifically for new 2GIG Alarm Systems. The good news is that our research has found that these sensor consistently and reliably work as intended, without causing any Supervision Trouble, as long as you follow some basic principles when using and setting up these devices. In addition to making sure that your sensor is powered on and communicating successfully with your 2GIG GC3e Panel, here are three (3) quick and easy tips to keep in mind whenever you are enrolling or configuring your 2GIG eSeries Sensors with your GC3e.

1) Reprogram from scratch when replacing an old sensor. If you have a sensor enrolled with your 2GIG GC3e, and you need to replace it with a new one, then you should remember to clear or delete the zone first, and then reprogram the entire zone from scratch, this time using the new sensor. Many users will need to do this if an old sensor becomes lost or damaged. While it might seem easier to just go in and remove the enrolled Serial Number for the zone, and then auto-learn the new one, this process has been known to cause Supervision Troubles. It's true that a sensor is identified based on its Serial Number, but you can't just delete the old Serial Number, add the new one, and expect everything to work perfectly. This is even the case if you are deleting a sensor and replacing it with one of the exact same model, for the exact same Sensor Type. Instead, take the extra time, delete the zone entirely, and then program it from scratch. For more information on the process, please review this page.

2) Reprogram from scratch when moving a sensor to a new partition. The same rule applies if you are moving an existing sensor to a new partition. This may be something to keep in mind if you are setting up system partitions for the first time, or if you want to change which zones users on a certain partition are able to control. If you are unaware, the 2GIG GC3e supports four (4) partitions, which are referred to as "Smart Areas", and the feature must be enabled at Q69 of System Configuration. More information on Smart Areas and how to set them up can be found here. Regardless, many users think that they can simply change the Partition Assignment within a zone, while keeping all other zone settings the same, and expect it to then function without a hitch. Unfortunately, it isn't that easy, as not completing this process properly may result in Supervision Trouble. Again, you must clear out the zone, and reprogram it from scratch. The only difference is that this time, you must assign the correct partition number, instead of the one it used originally. Alarm Grid invites you to check out this FAQ on switching GC3e Partition Assignments.

3) Always use the correct Equipment Code for 2GIG eSeries Sensors. The last tip we have involves the use of proper Equipment Codes. Before the rise of encryption, the Equipment Code setting was largely symbolic, and as long as an appropriate "equivalent" equipment code was used when programming a sensor, no issues would likely occur. But since the encrypted 2GIG eSeries Sensors use advanced "two-way" communication, using an incorrect Equipment Code can cause unwanted behavior, including Supervision Trouble. This one is a bit easier to fix, as you can often just replace the improper Equipment Code with the correct one in zone programming. If that doesn't work, then you can take the next step of trying to reprogram the entire zone from scratch. But you should be able to clear the trouble condition as normal once the Equipment Code is correct, based on the eSeries Sensor you are using.

The table below shows the Equipment Codes for 2GIG eSeries Sensors:

If you are an Alarm Grid monitored customer needing help with your 2GIG GC3e, or if you are interested in starting new service with Alarm Grid, please email our technical support team and security system planners at support@alarmgrid.com. We're here to help you from 9am to 8pm ET M-F. We look forward to hearing from you!

One thing we have noticed about the 2GIG GC3e is that it seems to be prone to erroneous Supervision Trouble conditions. This has left some users confused as to why their system zones are not working properly. But luckily, we have some tips to prevent this from happening to you and your GC3e.

Before we give our three (3) tips to follow, let's make sure we're all on the same page by explaining what Supervision Trouble normally refers to. Supervision Trouble occurs when a system does not receive a periodic "check-in" signal from an enrolled wireless sensor. This is usually either the result of the sensor not being able to send out its check-in signal, or the check-in signal not reaching the intended destination of the alarm panel. Some reasons why the sensor might not send out the signal include the sensor being powered down due to a dead or removed battery, or the sensor being physically destroyed. Some reasons why the the sensor's wireless check-in signal might not reach the alarm panel could include the sensor being moved to a new location in the building, or new obstacles, such as thick walls or large metal structures, being added inside the building. Regardless of the cause, you need to make it so that the sensor's check-in signals successfully reach the panel. Once you do that, you can clear the trouble condition. For GC3e users, you can learn how to clear the trouble condition by reviewing this FAQ.

But for the 2GIG GC3e, we have seen Supervision Trouble conditions occur, even when the sensor is powered on, successfully enrolled, and in clear communication range of the alarm panel. The issue seems to be particularly prevalent for the encrypted 2GIG eSeries Sensors that were built specifically for new 2GIG Alarm Systems. The good news is that our research has found that these sensor consistently and reliably work as intended, without causing any Supervision Trouble, as long as you follow some basic principles when using and setting up these devices. In addition to making sure that your sensor is powered on and communicating successfully with your 2GIG GC3e Panel, here are three (3) quick and easy tips to keep in mind whenever you are enrolling or configuring your 2GIG eSeries Sensors with your GC3e.

1) Reprogram from scratch when replacing an old sensor. If you have a sensor enrolled with your 2GIG GC3e, and you need to replace it with a new one, then you should remember to clear or delete the zone first, and then reprogram the entire zone from scratch, this time using the new sensor. Many users will need to do this if an old sensor becomes lost or damaged. While it might seem easier to just go in and remove the enrolled Serial Number for the zone, and then auto-learn the new one, this process has been known to cause Supervision Troubles. It's true that a sensor is identified based on its Serial Number, but you can't just delete the old Serial Number, add the new one, and expect everything to work perfectly. This is even the case if you are deleting a sensor and replacing it with one of the exact same model, for the exact same Sensor Type. Instead, take the extra time, delete the zone entirely, and then program it from scratch. For more information on the process, please review this page.

2) Reprogram from scratch when moving a sensor to a new partition. The same rule applies if you are moving an existing sensor to a new partition. This may be something to keep in mind if you are setting up system partitions for the first time, or if you want to change which zones users on a certain partition are able to control. If you are unaware, the 2GIG GC3e supports four (4) partitions, which are referred to as "Smart Areas", and the feature must be enabled at Q69 of System Configuration. More information on Smart Areas and how to set them up can be found here. Regardless, many users think that they can simply change the Partition Assignment within a zone, while keeping all other zone settings the same, and expect it to then function without a hitch. Unfortunately, it isn't that easy, as not completing this process properly may result in Supervision Trouble. Again, you must clear out the zone, and reprogram it from scratch. The only difference is that this time, you must assign the correct partition number, instead of the one it used originally. Alarm Grid invites you to check out this FAQ on switching GC3e Partition Assignments.

3) Always use the correct Equipment Code for 2GIG eSeries Sensors. The last tip we have involves the use of proper Equipment Codes. Before the rise of encryption, the Equipment Code setting was largely symbolic, and as long as an appropriate "equivalent" equipment code was used when programming a sensor, no issues would likely occur. But since the encrypted 2GIG eSeries Sensors use advanced "two-way" communication, using an incorrect Equipment Code can cause unwanted behavior, including Supervision Trouble. This one is a bit easier to fix, as you can often just replace the improper Equipment Code with the correct one in zone programming. If that doesn't work, then you can take the next step of trying to reprogram the entire zone from scratch. But you should be able to clear the trouble condition as normal once the Equipment Code is correct, based on the eSeries Sensor you are using.

The table below shows the Equipment Codes for 2GIG eSeries Sensors:

If you are an Alarm Grid monitored customer needing help with your 2GIG GC3e, or if you are interested in starting new service with Alarm Grid, please email our technical support team and security system planners at support@alarmgrid.com. We're here to help you from 9am to 8pm ET M-F. We look forward to hearing from you!

Last week, we took a look at three of the best alarm panels in the industry. These were the Honeywell Lyric, the Qolsys IQ Panel 2 Plus, and the 2GIG GC3e. Today, we are checking out the sensors that you can add to support these systems. Here is our 2020 Security Sensor Buying Guide!

Sensors are accessories that are added to alarm systems to report specific activity. Each sensor has its own job of looking for a certain type of activity in its designated location. All of the sensors on a system communicate with a single centralized panel or hub. This panel is actively listening for any sensor that is triggered due to a potentially important system event. Adding new sensors is perhaps the best way to expand upon an existing system, and they make awesome gifts and stocking stuffers for the security enthusiast in your life.

Broadly speaking, sensors can be split into two main categories, which are security and life safety/environmental. Security sensors look for activity that suggests potentially unauthorized entry into a monitored and protected location, such as a door being opened, movement in a room where nobody is supposed to be present, or a window being broken. Life safety/environmental sensors look for activity associated with unwanted or potentially harmful conditions that affect the well-being of those in the area, such as a flood, an extreme temperature, a fire, or the presence of CO gas. We'll be taking a look at life safety/environmental sensors another time. Today, our focus is on security sensors.

Wireless Sensor Basics

Before we dive into specific security sensors for our top panel picks, we're going to start by giving you some general, generic information that can be applied to any sensor out there. First, understand that this post is focusing only on wireless sensors. These are almost always the sensors chosen for use with wireless alarm systems. Wired sensors can also technically be used with wireless panels but a converter module is almost always needed. Not to mention the fact that wireless sensors are significantly easier to install, especially for DIY users. The only time you will realistically see wired sensors used with a wireless panel is if a user is upgrading from an older wired system and bringing over their old wired sensors, or in new construction where a user wants to integrate the sensors in with the building. But if you're expanding upon a wireless system by getting new sensors, then the new sensors will almost certainly be wireless.

The important thing to remember when choosing wireless sensors for a wireless alarm panel is making sure the sensor is compatible with the system. It doesn't matter if a sensor has all the specs and features if it doesn't work with your panel! The way to determine compatibility is to look at the lineup that the sensor is from. Petty much every wireless sensor out there is part of a larger grouping of sensors that will all have the same compatibility.

To make it easier for you, we have the three panels we mentioned before (well, make that five, as the Qolsys IQ Panel 2 Plus actually comes in three versions), and all their compatible sensor lineups conveniently listed. We hope that this sheds some light on your options. The only caveat is that for any panel listed here that supports the Honeywell 5800 Sensors, we must be clear that this is only for the uni-directional sensors with one-way communication in the lineup. Any bi-directional Honeywell 5800 Sensors with two-way communication will not work with any of the aforementioned systems. The bi-directional Honeywell 5800 Sensors are only compatible with the Honeywell LYNX Touch and VISTA Systems, which were not included in our buying guides.

With that out of the way, here are compatible sensor lineups by system:

• Honeywell Lyric - Honeywell SiX Series, Honeywell 5800 Series, 2GIG 345 MHz Series
• 2GIG GC3e - 2GIG eSeries Encrypted Sensors, 2GIG 345 MHz Series, Honeywell 5800 Series
• Qolsys IQ Panel 2 Plus 319.5 MHz - DSC PowerG Sensors, Qolsys S-Line Sensors, Qolsys Legacy 319.5 MHz Sensors, Legacy Interlogix Sensors, Legacy GE Sensors
• Qolsys IQ Panel 2 Plus 345 MHz - DSC PowerG Sensors, Honeywell 5800 Sensors, 2GIG 345 MHz Sensors
• Qolsys IQ Panel 2 Plus 433 MHz - DSC PowerG Sensors, Legacy DSC 433 MHZ Sensors

You will notice that some of the sensor groups listed above are italicized and underlined. That is done to identify the lineups of encrypted sensors. These encrypted sensors have special protection measures put in place to make them more secure and less prone to being hacked or defeated by malicious attacks. Encrypted sensors tend to have more restricted compatibility. They may follow a special enrollment process. Encrypted sensors often use bi-directional communication so that the sensor knows that it is actively paired with the system. Many encrypted sensors may only be paired with a single system at any given time, and the sensor will need to be deleted from its existing system before it will work with a new one.

It's okay to use non-encrypted sensors with your system, especially in zones that are less likely to trigger an alarm, like a second story window. Many users will opt to use a mixture of both encrypted and non-encrypted sensors. Other users feel comfortable using entirely non-encrypted sensors. It really comes down to your level of comfort. Non-encrypted sensors are secure in most situations, and they are still tricky to defeat. But going fully encrypted is recommended for anyone seeking maximum security. One tip if you do decide to go with some non-encrypted sensors is to avoid letting others know what wireless frequency your sensors use or what type of system you have installed. Knowing the frequency and the system being used makes it much easier for a savvy intruder to defeat a sensor.

Door & Window Alarm Sensors

Now that you know some basics that apply to almost all wireless sensors, let's start talking about specific types and models. Door and window sensors will let a system know when a door or window has been opened or closed. These are some of the most basic and easy to use sensors on a security system. These devices work by using a larger sensor portion and a smaller magnet portion. The sensor is placed on or inside the door or window frame, and the magnet is placed on or inside the moving portion of the door or window. When the door or window is opened, the magnet will move away from the sensor. This will trip a metal reed switch inside the sensor, which will tell the sensor to alert the system to the opened door or window. All of the sensors we've listed here follow that same method of operation.

Door and window sensors can be split into two (2) main categories. Surface-mount door and window sensors are mounted outside the door or window and its accompanying frame on the surface. The advantage to surface-mount door and window sensors is that they are very easy to install, and they can usually be mounted using double sided foam tape. But some users may not like how they are visible on the outside of the door or window. If you don't like the appearance of visible surface-mount door and window sensors, then you might instead consider recessed door and window sensors. A recessed door or window sensor is installed inside a door or window and its frame, so that it is hidden and cannot be seen from the outside. Recessed door and window sensors are more difficult and time-consuming to install, because you must drill holes in both the door or window and its accompanying frame. Whether you decide to use surface-mount door and window sensors, or recessed door and window sensors is up to you. Most DIY users and Alarm Grid customers in general will use surface-mount door and window sensors.

Now let's look at some door and window sensors.:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Installation	Notes
Honeywell SiXMINICT	Honeywell SiX Series	Lyric	200 Nominal Feet	128-bit AES	Surface-Mount	Premier mini encrypted door/window Sensor for Lyric.
DSC PG9303	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Surface-Mount	PowerG encrypted surface mount door/window sensor.
DSC PG9307	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Recessed	PowerG encrypted recessed door/window sensor.
2GIG DW10e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	Surface-Mount	Encrypted surface-mount sensor for 2GIG
2GIG DW20e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	Recessed	Encrypted recessed sensor for 2GIG
Qolsys IQ DW Mini-S	Qolsys S-Line	319.5 MHz IQ2+	600 Feet Open Air	Qolsys S-Line Encryption	Surface-Mount	Encrypted surface-mount sensor for 319.5 MHz systems.
Qolsys IQ Recessed Door-S	Qolsys S-Line	319.5 MHz IQ 2+	600 Feet Open Air	Qolsys S-Line Encryption	Recessed	Encrypted recessed sensor for 319.5 MHz systems.
Honeywell 5818MNL	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Recessed	Non-Encrypted recessed door/window sensor for 345 MHz systems.
VERSA-2GIG	2GIG 345 MHz	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Non-encrypted surface-mount sensor for 345 MHz systems.
VERSA-GE	Legacy GE	319.5 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Non-encrypted surface-mount sensor for 319.5 MHz systems.
VERSA-DSC	Legacy DSC	433 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Non-encrypted surface-mount sensor for 433 MHz systems.

We also want to share a selection of outdoor door and window sensors with you. These surface-mount contact sensors are specifically designed to withstand the conditions of an outdoor environment, including intense rain, wind, dust, and sunlight. You can see them listed below.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Installation	Notes
Honeywell 5816OD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Outdoor contact sensor from 5800 Series.
DSC PG9312	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Surface-Mount	PowerG Outdoor Contact Sensor.
2GIG DW30-345	2GIG 345 MHz	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	Surface-Mount	Outdoor contact sensor from 2GIG 345 MHz series.

Motion Sensors

Motion sensors use passive infrared (PIR) technology to detect movement within the sensor's coverage area. This is done by looking for the changes in infrared (IR) energy that occur when a person, animal, or object comes within the sensor's field of view. Standard motion sensors are typically PIR only. These are appropriately called PIR motion sensors.

Some motion sensors will also use microwave technology in addition to PIR technology. This involves having the sensor send out microwave signals and seeing how the signals bounce off of objects in the area. Movement will change the pattern of these microwave signals, and the sensor will be able to detect this. These motion sensors that use both microwave and PIR are called Dual-Tech motion sensors. The purpose of using both PIR and microwave together is to prevent false alarms. A Dual-Tech motion sensor will only activate and alert the system if both its PIR sensor and its microwave sensor are triggered. A microwave sensor is not vulnerable to the same environmental issues that may cause a false activation on a PIR. You will not find a motion sensor that uses microwave technology without PIR detection, as microwave alone would result in too many false alarms without having PIR to confirm movement.

One feature that you will often see listed on a motion sensor is pet-immunity. A motion sensor that has been set up for pet immunity can be configured to not "look" in the areas close to the ground where pets and small animals walk. Instead, the motion sensor only looks in the areas higher up, where humans move while walking upright. A pet immune motion sensor is not impervious to small animals, and you must position it carefully so that it works as intended. Pet immune motion sensors normally have a weight limit, where animals under that weight limit should avoid triggering the sensor, assuming that the sensor is installed properly. Please note that most pet friendly motion sensors will require you to set the sensitivity for the sensor to the lowest possible setting.

When it comes to motion sensors, mounting them carefully is very important. A motion sensor may cause false alarms on the system if it is not installed properly. These sensors should not be facing any vents, air ducts, ceiling fans, or curtains that may cause the sensor to activate without any movement. If you are using the motion sensor for pet immunity, then it should also not be facing any furniture or stairwells that your pet could use to get within the sensor's field of view. You will likely want to perform a Walk Test of your motion sensor to make sure that it responds properly when movement is present, and does not respond due to other external factors when there is no movement. You should also have any pets participate in the Walk Test to ensure that pet immunity is working properly.

We recommend reading the following FAQs to learn more about motion sensors:

• What is a PIR Motion Sensor?
• What are Microwave Motion Sensors?
• What is a Pet-Immune Motion Sensor?

Below are some of the most popular motion sensors for our recommended systems:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Coverage Area	Detection Type	Pet Immunity	Notes
Honeywell SiXPIR	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	40 by 56 Feet	PIR	Up to 80 lbs	Encrypted PIR Motion for Lyric.
DSC PG9914	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Up to 39 Feet	PIR	Up to 85 lbs	PowerG Encrypted PIR Motion.
DSC PG9984P	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Up to 50 Feet	Dual-Tech	Up to 40 lbs	PowerG Encrypted Dual-Tech Motion.
2GIG PIR1e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	30 by 50 Feet	PIR	Up to 55 lbs	Encrypted PIR Motion for 2GIG.
Honeywell 5800PIR-RES	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	35 by 40 Feet	PIR	Up to 80 lbs	Non-encrypted residential PIR motion for 345 MHz systems.
Honeywell 5800PIR-COM	Honeywell 5800 Series	Lyric, GC3e, 345 MHz, IQ2+	200 Nominal Feet	None	60 by 80 Feet	PIR	None	Non-encrypted commercial PIR motion for 345 MHz systems.
Honeywell 5898	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	35 by 40 Feet for Pet Immunity	Dual-Tech	Up to 100 lbs	Non-encrypted Dual-Tech motion for 345 MHz systems.
Qolsys IQ Motion-S	Qolsys S-Line	319.5 MHz IQ2+	600 Feet Open Air	Qolsys S-Line Encryption	30 by 40 Feet	PIR	Up to 40 lbs	Non-encrypted PIR motion for 319.5 MHz systems.

There are also certain outdoor motion detection sensors that are better-suited for use in an outdoor environment. These outdoor motion sensor models are typically more expensive than indoor variants. You can see some of our most popular ones listed below:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Coverage Area	Detection Type	Pet Immunity	Notes
DSC PG9994	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Up to 30 Feet	PIR	Up to 40 lbs	PowerG Outdoor PIR Motion Sensor
Honeywell 5800PIR-OD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	40 by 30 Feet	PIR	None	Honeywell 5800 Series Outdoor Motion, 1st ed.
Honeywell 5800PIR-OD2	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	40 by 30 Feet	PIR	None	Honeywell 5800 Series Outdoor Motion, 2nd ed.
Optex FTN-RRIX	Legacy Interlogix	319.5 MHz IQ2+	200 Nominal Feet	None	Up to 16.5 Feet	PIR	None	Optex Fitlink Outdoor Motion Sensor for 319.5 MHz Systems
Optex FTN-RR2G	2GIG 345 MHz	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Up to 16.5 Feet	PIR	None	Optex Fitlink Outdoor Motion Sensor for 345 MHz Systems.
Optex FTN-RRDS	Legacy DSC	433 MHz IQ2+	200 Nominal Feet	None	Up to 16.5 Feet	PIR	None	Optex Fitlink Outdoor Motion Sensor for 433 MHz Systems.

Glass Break Sensors

The last type of security sensors we will be discussing are glass break sensors. These sensors include built-in microphones, and they actively listen for the unique sound of glass breaking. Most of these sensors will need to hear both the high-pitched shattering sound of the glass breaking, as well as the low-pitched sound of an object striking against the glass in order to activate. This design choice is to prevent false alarms caused by similar sounds. Most users will use glass break sensors to monitor windows, but they have also been known to work effectively on protective glass display cases that store valuables, such as what you might find in jewelry stores or gun shops. Most types of glass will work with glass break sensors, though there are some exceptions. For example double and triple pane glass windows won't work reliably. The same is true for coated or "safety" glass. Refer to the manual for the exact glass break detector you are using to determine compatibility.

A single glass break detector can monitor multiple windows or display cases, as long as the glass it is monitoring is within its detection range, which is typically 15 to 25 feet. Any glass that is being monitored must have a direct line of sight with the sensor, with no obstacles blocking the path that sound will travel through. When testing your glass break sensors, it is strongly recommended that you us a glass break simulator. These devices will mimic the sound of the glass breaking and activate your glass break sensors without actually breaking any glass. Remember to refer the instructions of your glass break simulator for more information. When choosing a glass break simulator, it is best to use a simulator from the same manufacturer, if possible. We have a Honeywell Glass Break Simulator and a DSC Glass Break Simulator available on our website. If you get one of the 2GIG Glass Break Sensors mentioned in this buying guide, then the Honeywell Glass Break Simulator is best for testing. Otherwise, just match the manufacturer.

• Honeywell FG701 Glass Break Simulator
• DSC AFT-100 Glass Break Simulator

Below are some of our most popular glass break sensors:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Honeywell SiXGB	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	SiX Series Glass Break Sensor for Lyric
DSC PG922	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG Glass Break Sensor
2GIG GB1e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	Encrypted glass break sensor for 2GIG.
Honeywell 5853	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Non-encrypted glass break sensor for 345 MHz systems.
Qolsys IQ Glass-S	Qolsys S-Line	319.5 MHz IQ2+	600 Feet Open Air	Qolsys S-Line Encryption	Encrypted glass break sensor for 319.5 MHz systems.

Reach Out to Us!

Remember that you can reach out to us with any questions you might have about planning your system and determining sensor compatibility. The best way to contact us is to email support@alarmgrid.com. This is also a good email to use if you are interested in starting new alarm monitoring service with Alarm Grid. Our team checks for new email from 9am to 8pm ET M-F. We look forward to hearing from you!

Last week, we took a look at three of the best alarm panels in the industry. These were the Honeywell Lyric, the Qolsys IQ Panel 2 Plus, and the 2GIG GC3e. Today, we are checking out the sensors that you can add to support these systems. Here is our 2020 Security Sensor Buying Guide!

Sensors are accessories that are added to alarm systems to report specific activity. Each sensor has its own job of looking for a certain type of activity in its designated location. All of the sensors on a system communicate with a single centralized panel or hub. This panel is actively listening for any sensor that is triggered due to a potentially important system event. Adding new sensors is perhaps the best way to expand upon an existing system, and they make awesome gifts and stocking stuffers for the security enthusiast in your life.

Broadly speaking, sensors can be split into two main categories, which are security and life safety/environmental. Security sensors look for activity that suggests potentially unauthorized entry into a monitored and protected location, such as a door being opened, movement in a room where nobody is supposed to be present, or a window being broken. Life safety/environmental sensors look for activity associated with unwanted or potentially harmful conditions that affect the well-being of those in the area, such as a flood, an extreme temperature, a fire, or the presence of CO gas. We'll be taking a look at life safety/environmental sensors another time. Today, our focus is on security sensors.

Wireless Sensor Basics

Before we dive into specific security sensors for our top panel picks, we're going to start by giving you some general, generic information that can be applied to any sensor out there. First, understand that this post is focusing only on wireless sensors. These are almost always the sensors chosen for use with wireless alarm systems. Wired sensors can also technically be used with wireless panels but a converter module is almost always needed. Not to mention the fact that wireless sensors are significantly easier to install, especially for DIY users. The only time you will realistically see wired sensors used with a wireless panel is if a user is upgrading from an older wired system and bringing over their old wired sensors, or in new construction where a user wants to integrate the sensors in with the building. But if you're expanding upon a wireless system by getting new sensors, then the new sensors will almost certainly be wireless.

The important thing to remember when choosing wireless sensors for a wireless alarm panel is making sure the sensor is compatible with the system. It doesn't matter if a sensor has all the specs and features if it doesn't work with your panel! The way to determine compatibility is to look at the lineup that the sensor is from. Petty much every wireless sensor out there is part of a larger grouping of sensors that will all have the same compatibility.

To make it easier for you, we have the three panels we mentioned before (well, make that five, as the Qolsys IQ Panel 2 Plus actually comes in three versions), and all their compatible sensor lineups conveniently listed. We hope that this sheds some light on your options. The only caveat is that for any panel listed here that supports the Honeywell 5800 Sensors, we must be clear that this is only for the uni-directional sensors with one-way communication in the lineup. Any bi-directional Honeywell 5800 Sensors with two-way communication will not work with any of the aforementioned systems. The bi-directional Honeywell 5800 Sensors are only compatible with the Honeywell LYNX Touch and VISTA Systems, which were not included in our buying guides.

With that out of the way, here are compatible sensor lineups by system:

• Honeywell Lyric - Honeywell SiX Series, Honeywell 5800 Series, 2GIG 345 MHz Series
• 2GIG GC3e - 2GIG eSeries Encrypted Sensors, 2GIG 345 MHz Series, Honeywell 5800 Series
• Qolsys IQ Panel 2 Plus 319.5 MHz - DSC PowerG Sensors, Qolsys S-Line Sensors, Qolsys Legacy 319.5 MHz Sensors, Legacy Interlogix Sensors, Legacy GE Sensors
• Qolsys IQ Panel 2 Plus 345 MHz - DSC PowerG Sensors, Honeywell 5800 Sensors, 2GIG 345 MHz Sensors
• Qolsys IQ Panel 2 Plus 433 MHz - DSC PowerG Sensors, Legacy DSC 433 MHZ Sensors

You will notice that some of the sensor groups listed above are italicized and underlined. That is done to identify the lineups of encrypted sensors. These encrypted sensors have special protection measures put in place to make them more secure and less prone to being hacked or defeated by malicious attacks. Encrypted sensors tend to have more restricted compatibility. They may follow a special enrollment process. Encrypted sensors often use bi-directional communication so that the sensor knows that it is actively paired with the system. Many encrypted sensors may only be paired with a single system at any given time, and the sensor will need to be deleted from its existing system before it will work with a new one.

It's okay to use non-encrypted sensors with your system, especially in zones that are less likely to trigger an alarm, like a second story window. Many users will opt to use a mixture of both encrypted and non-encrypted sensors. Other users feel comfortable using entirely non-encrypted sensors. It really comes down to your level of comfort. Non-encrypted sensors are secure in most situations, and they are still tricky to defeat. But going fully encrypted is recommended for anyone seeking maximum security. One tip if you do decide to go with some non-encrypted sensors is to avoid letting others know what wireless frequency your sensors use or what type of system you have installed. Knowing the frequency and the system being used makes it much easier for a savvy intruder to defeat a sensor.

Door & Window Alarm Sensors

Now that you know some basics that apply to almost all wireless sensors, let's start talking about specific types and models. Door and window sensors will let a system know when a door or window has been opened or closed. These are some of the most basic and easy to use sensors on a security system. These devices work by using a larger sensor portion and a smaller magnet portion. The sensor is placed on or inside the door or window frame, and the magnet is placed on or inside the moving portion of the door or window. When the door or window is opened, the magnet will move away from the sensor. This will trip a metal reed switch inside the sensor, which will tell the sensor to alert the system to the opened door or window. All of the sensors we've listed here follow that same method of operation.

Door and window sensors can be split into two (2) main categories. Surface-mount door and window sensors are mounted outside the door or window and its accompanying frame on the surface. The advantage to surface-mount door and window sensors is that they are very easy to install, and they can usually be mounted using double sided foam tape. But some users may not like how they are visible on the outside of the door or window. If you don't like the appearance of visible surface-mount door and window sensors, then you might instead consider recessed door and window sensors. A recessed door or window sensor is installed inside a door or window and its frame, so that it is hidden and cannot be seen from the outside. Recessed door and window sensors are more difficult and time-consuming to install, because you must drill holes in both the door or window and its accompanying frame. Whether you decide to use surface-mount door and window sensors, or recessed door and window sensors is up to you. Most DIY users and Alarm Grid customers in general will use surface-mount door and window sensors.

Now let's look at some door and window sensors.:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Installation	Notes
Honeywell SiXMINICT	Honeywell SiX Series	Lyric	200 Nominal Feet	128-bit AES	Surface-Mount	Premier mini encrypted door/window Sensor for Lyric.
DSC PG9303	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Surface-Mount	PowerG encrypted surface mount door/window sensor.
DSC PG9307	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Recessed	PowerG encrypted recessed door/window sensor.
2GIG DW10e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	Surface-Mount	Encrypted surface-mount sensor for 2GIG
2GIG DW20e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	Recessed	Encrypted recessed sensor for 2GIG
Qolsys IQ DW Mini-S	Qolsys S-Line	319.5 MHz IQ2+	600 Feet Open Air	Qolsys S-Line Encryption	Surface-Mount	Encrypted surface-mount sensor for 319.5 MHz systems.
Qolsys IQ Recessed Door-S	Qolsys S-Line	319.5 MHz IQ 2+	600 Feet Open Air	Qolsys S-Line Encryption	Recessed	Encrypted recessed sensor for 319.5 MHz systems.
Honeywell 5818MNL	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Recessed	Non-Encrypted recessed door/window sensor for 345 MHz systems.
VERSA-2GIG	2GIG 345 MHz	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Non-encrypted surface-mount sensor for 345 MHz systems.
VERSA-GE	Legacy GE	319.5 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Non-encrypted surface-mount sensor for 319.5 MHz systems.
VERSA-DSC	Legacy DSC	433 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Non-encrypted surface-mount sensor for 433 MHz systems.

We also want to share a selection of outdoor door and window sensors with you. These surface-mount contact sensors are specifically designed to withstand the conditions of an outdoor environment, including intense rain, wind, dust, and sunlight. You can see them listed below.

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Installation	Notes
Honeywell 5816OD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Surface-Mount	Outdoor contact sensor from 5800 Series.
DSC PG9312	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Surface-Mount	PowerG Outdoor Contact Sensor.
2GIG DW30-345	2GIG 345 MHz	Lyric, GC3e, 345 MHz IQ2+	350 Nominal Feet	None	Surface-Mount	Outdoor contact sensor from 2GIG 345 MHz series.

Motion Sensors

Motion sensors use passive infrared (PIR) technology to detect movement within the sensor's coverage area. This is done by looking for the changes in infrared (IR) energy that occur when a person, animal, or object comes within the sensor's field of view. Standard motion sensors are typically PIR only. These are appropriately called PIR motion sensors.

Some motion sensors will also use microwave technology in addition to PIR technology. This involves having the sensor send out microwave signals and seeing how the signals bounce off of objects in the area. Movement will change the pattern of these microwave signals, and the sensor will be able to detect this. These motion sensors that use both microwave and PIR are called Dual-Tech motion sensors. The purpose of using both PIR and microwave together is to prevent false alarms. A Dual-Tech motion sensor will only activate and alert the system if both its PIR sensor and its microwave sensor are triggered. A microwave sensor is not vulnerable to the same environmental issues that may cause a false activation on a PIR. You will not find a motion sensor that uses microwave technology without PIR detection, as microwave alone would result in too many false alarms without having PIR to confirm movement.

One feature that you will often see listed on a motion sensor is pet-immunity. A motion sensor that has been set up for pet immunity can be configured to not "look" in the areas close to the ground where pets and small animals walk. Instead, the motion sensor only looks in the areas higher up, where humans move while walking upright. A pet immune motion sensor is not impervious to small animals, and you must position it carefully so that it works as intended. Pet immune motion sensors normally have a weight limit, where animals under that weight limit should avoid triggering the sensor, assuming that the sensor is installed properly. Please note that most pet friendly motion sensors will require you to set the sensitivity for the sensor to the lowest possible setting.

When it comes to motion sensors, mounting them carefully is very important. A motion sensor may cause false alarms on the system if it is not installed properly. These sensors should not be facing any vents, air ducts, ceiling fans, or curtains that may cause the sensor to activate without any movement. If you are using the motion sensor for pet immunity, then it should also not be facing any furniture or stairwells that your pet could use to get within the sensor's field of view. You will likely want to perform a Walk Test of your motion sensor to make sure that it responds properly when movement is present, and does not respond due to other external factors when there is no movement. You should also have any pets participate in the Walk Test to ensure that pet immunity is working properly.

We recommend reading the following FAQs to learn more about motion sensors:

• What is a PIR Motion Sensor?
• What are Microwave Motion Sensors?
• What is a Pet-Immune Motion Sensor?

Below are some of the most popular motion sensors for our recommended systems:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Coverage Area	Detection Type	Pet Immunity	Notes
Honeywell SiXPIR	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	40 by 56 Feet	PIR	Up to 80 lbs	Encrypted PIR Motion for Lyric.
DSC PG9914	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Up to 39 Feet	PIR	Up to 85 lbs	PowerG Encrypted PIR Motion.
DSC PG9984P	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Up to 50 Feet	Dual-Tech	Up to 40 lbs	PowerG Encrypted Dual-Tech Motion.
2GIG PIR1e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	30 by 50 Feet	PIR	Up to 55 lbs	Encrypted PIR Motion for 2GIG.
Honeywell 5800PIR-RES	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	35 by 40 Feet	PIR	Up to 80 lbs	Non-encrypted residential PIR motion for 345 MHz systems.
Honeywell 5800PIR-COM	Honeywell 5800 Series	Lyric, GC3e, 345 MHz, IQ2+	200 Nominal Feet	None	60 by 80 Feet	PIR	None	Non-encrypted commercial PIR motion for 345 MHz systems.
Honeywell 5898	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	35 by 40 Feet for Pet Immunity	Dual-Tech	Up to 100 lbs	Non-encrypted Dual-Tech motion for 345 MHz systems.
Qolsys IQ Motion-S	Qolsys S-Line	319.5 MHz IQ2+	600 Feet Open Air	Qolsys S-Line Encryption	30 by 40 Feet	PIR	Up to 40 lbs	Non-encrypted PIR motion for 319.5 MHz systems.

There are also certain outdoor motion detection sensors that are better-suited for use in an outdoor environment. These outdoor motion sensor models are typically more expensive than indoor variants. You can see some of our most popular ones listed below:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Coverage Area	Detection Type	Pet Immunity	Notes
DSC PG9994	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	Up to 30 Feet	PIR	Up to 40 lbs	PowerG Outdoor PIR Motion Sensor
Honeywell 5800PIR-OD	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	40 by 30 Feet	PIR	None	Honeywell 5800 Series Outdoor Motion, 1st ed.
Honeywell 5800PIR-OD2	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	40 by 30 Feet	PIR	None	Honeywell 5800 Series Outdoor Motion, 2nd ed.
Optex FTN-RRIX	Legacy Interlogix	319.5 MHz IQ2+	200 Nominal Feet	None	Up to 16.5 Feet	PIR	None	Optex Fitlink Outdoor Motion Sensor for 319.5 MHz Systems
Optex FTN-RR2G	2GIG 345 MHz	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Up to 16.5 Feet	PIR	None	Optex Fitlink Outdoor Motion Sensor for 345 MHz Systems.
Optex FTN-RRDS	Legacy DSC	433 MHz IQ2+	200 Nominal Feet	None	Up to 16.5 Feet	PIR	None	Optex Fitlink Outdoor Motion Sensor for 433 MHz Systems.

Glass Break Sensors

The last type of security sensors we will be discussing are glass break sensors. These sensors include built-in microphones, and they actively listen for the unique sound of glass breaking. Most of these sensors will need to hear both the high-pitched shattering sound of the glass breaking, as well as the low-pitched sound of an object striking against the glass in order to activate. This design choice is to prevent false alarms caused by similar sounds. Most users will use glass break sensors to monitor windows, but they have also been known to work effectively on protective glass display cases that store valuables, such as what you might find in jewelry stores or gun shops. Most types of glass will work with glass break sensors, though there are some exceptions. For example double and triple pane glass windows won't work reliably. The same is true for coated or "safety" glass. Refer to the manual for the exact glass break detector you are using to determine compatibility.

A single glass break detector can monitor multiple windows or display cases, as long as the glass it is monitoring is within its detection range, which is typically 15 to 25 feet. Any glass that is being monitored must have a direct line of sight with the sensor, with no obstacles blocking the path that sound will travel through. When testing your glass break sensors, it is strongly recommended that you us a glass break simulator. These devices will mimic the sound of the glass breaking and activate your glass break sensors without actually breaking any glass. Remember to refer the instructions of your glass break simulator for more information. When choosing a glass break simulator, it is best to use a simulator from the same manufacturer, if possible. We have a Honeywell Glass Break Simulator and a DSC Glass Break Simulator available on our website. If you get one of the 2GIG Glass Break Sensors mentioned in this buying guide, then the Honeywell Glass Break Simulator is best for testing. Otherwise, just match the manufacturer.

• Honeywell FG701 Glass Break Simulator
• DSC AFT-100 Glass Break Simulator

Below are some of our most popular glass break sensors:

Sensor Name	Product Lineup	Compatibility	Range	Encryption	Notes
Honeywell SiXGB	Honeywell SiX Series	Lyric	300 Nominal Feet	128-bit AES	SiX Series Glass Break Sensor for Lyric
DSC PG922	PowerG	All IQ Panel 2 Plus	2,000 Feet Open Air	128-bit AES	PowerG Glass Break Sensor
2GIG GB1e	2GIG eSeries	2GIG GC3e	350 Nominal Feet	2GIG eSeries Encryption	Encrypted glass break sensor for 2GIG.
Honeywell 5853	Honeywell 5800 Series	Lyric, GC3e, 345 MHz IQ2+	200 Nominal Feet	None	Non-encrypted glass break sensor for 345 MHz systems.
Qolsys IQ Glass-S	Qolsys S-Line	319.5 MHz IQ2+	600 Feet Open Air	Qolsys S-Line Encryption	Encrypted glass break sensor for 319.5 MHz systems.

Reach Out to Us!

Remember that you can reach out to us with any questions you might have about planning your system and determining sensor compatibility. The best way to contact us is to email support@alarmgrid.com. This is also a good email to use if you are interested in starting new alarm monitoring service with Alarm Grid. Our team checks for new email from 9am to 8pm ET M-F. We look forward to hearing from you!

We have heard reports lately of RF supervision troubles on 2GIG GC2e and 2GIG GC3e Systems, particularly for zones set up with encrypted 2GIG eSeries Sensors. Upon further testing, we have learned that eSeries Zones configured with incorrect Equipment Codes can cause supervision trouble.

Equipment Codes are somewhat of a unique quirk for 2GIG Security Systems. This numeric code identifies the model number of the wireless sensor that is being used. It should not be confused with the sensor's Serial Number, which is unique for each individual sensor. You set the Equipment Code when programming a new zone. Alarm Grid has helpful guides available for programming a GC2e zone and programming a GC3e zone.

The following table contains the current list of eSeries Equipment Codes:

Before the rise of 2GIG eSeries Encrypted Sensors, the Equipment Code setting on a 2GIG System was largely seen as a formality. The general practice was to find the corresponding sensor if available, but generally not worry about it very much if you couldn't match it exactly. Some third-party sensors do not have their own Equipment Codes, and an "equivalent" is usually selected instead. For example, the Honeywell 5800MINI and the VERSA-2GIG can both just use the Equipment Code for "Existing Door/Window Contact", rather than finding an exact match.

But for the 2GIG eSeries Sensors, the Equipment Code selection is actually very important. Failing to set the exact corresponding equipment code can result in the system displaying an RF supervision loss trouble condition for the associated zone. This trouble is typically used to identify that the system has lost communication with the sensor, due to either the sensor powering down from a dead or missing battery, or the sensor being taken out of wireless range. But it seems that the GC2e and GC3e cannot properly supervise a 2GIG eSeries Sensor with an improper Equipment Code. More information can be found in this FAQ.

Missing Equipment Codes are more common for third-party sensors not produced by 2GIG. For a 2GIG Sensor, you should almost always have a direct Equipment Code selection available. And the 2GIG eSeries Sensors are still quite new, so 2GIG made sure to put in Equipment Codes specifically for each of these sensors. However, you may be unable to find an Equipment Code for a brand-new eSeries Sensor if your 2GIG System isn't on the latest firmware version. Adding support for new sensors is a major part of most 2GIG Firmware Updates. You can view our GC2e Firmware Page here, and our GC3e Firmware Page here.

If you need any help programming a GC2e or GC3e wireless zone, then make sure to check out the programming FAQs we linked earlier. Alarm Grid monitored customers can also receive additional free support by emailing support@alarmgrid.com. This is also a great email to use if you are interested in signing up for new monitoring service. We check our email from 9am to 8pm ET M-F. We look forward to hearing from you!

We have heard reports lately of RF supervision troubles on 2GIG GC2e and 2GIG GC3e Systems, particularly for zones set up with encrypted 2GIG eSeries Sensors. Upon further testing, we have learned that eSeries Zones configured with incorrect Equipment Codes can cause supervision trouble.

Equipment Codes are somewhat of a unique quirk for 2GIG Security Systems. This numeric code identifies the model number of the wireless sensor that is being used. It should not be confused with the sensor's Serial Number, which is unique for each individual sensor. You set the Equipment Code when programming a new zone. Alarm Grid has helpful guides available for programming a GC2e zone and programming a GC3e zone.

The following table contains the current list of eSeries Equipment Codes:

Before the rise of 2GIG eSeries Encrypted Sensors, the Equipment Code setting on a 2GIG System was largely seen as a formality. The general practice was to find the corresponding sensor if available, but generally not worry about it very much if you couldn't match it exactly. Some third-party sensors do not have their own Equipment Codes, and an "equivalent" is usually selected instead. For example, the Honeywell 5800MINI and the VERSA-2GIG can both just use the Equipment Code for "Existing Door/Window Contact", rather than finding an exact match.

But for the 2GIG eSeries Sensors, the Equipment Code selection is actually very important. Failing to set the exact corresponding equipment code can result in the system displaying an RF supervision loss trouble condition for the associated zone. This trouble is typically used to identify that the system has lost communication with the sensor, due to either the sensor powering down from a dead or missing battery, or the sensor being taken out of wireless range. But it seems that the GC2e and GC3e cannot properly supervise a 2GIG eSeries Sensor with an improper Equipment Code. More information can be found in this FAQ.

Missing Equipment Codes are more common for third-party sensors not produced by 2GIG. For a 2GIG Sensor, you should almost always have a direct Equipment Code selection available. And the 2GIG eSeries Sensors are still quite new, so 2GIG made sure to put in Equipment Codes specifically for each of these sensors. However, you may be unable to find an Equipment Code for a brand-new eSeries Sensor if your 2GIG System isn't on the latest firmware version. Adding support for new sensors is a major part of most 2GIG Firmware Updates. You can view our GC2e Firmware Page here, and our GC3e Firmware Page here.

If you need any help programming a GC2e or GC3e wireless zone, then make sure to check out the programming FAQs we linked earlier. Alarm Grid monitored customers can also receive additional free support by emailing support@alarmgrid.com. This is also a great email to use if you are interested in signing up for new monitoring service. We check our email from 9am to 8pm ET M-F. We look forward to hearing from you!

Hi DIYers! Today, we're taking a look at the new Interlogix Encrypted Sensors. There are three (3) sensors in this TX+ lineup. There is the Interlogix TX+DWS Door/Window Contact, the Interlogix TX+PIR Pet Immune Motion Sensor, and the Interlogix TX+2WAYFOB Key Fob. All are available now!

First, we would like to give some background on these Interlogix TX+ Sensors. The wireless communication range for these sensors is listed at 500 feet when used in open air. They operate at an encrypted 319.5 MHz frequency, similar to the Qolsys S-Line Sensors. You can technically use these Interlogix TX+ Sensors with any 319.5 MHz system. This includes the Qolsys IQ Panel 2 Plus w/ 319.5 MHz Daughtercard and all of the Wireless Interlogix Panels.

However, these sensors will only utilize encrypted communication when paired with the Interlogix Simon XTi-5i System. If you don't know about this system, we actually started carrying it last month. Among its new features is the ability to support encrypted sensors. At the time, there weren't any encrypted sensors out for the system yet. Well now there are! When paired with any other compatible system, they will operate as non-encrypted wireless sensors.

The sensors themselves are straightforward and simple. The Interlogix TX+DWS Contact has a thin profile, and it will work great on nearly any door, window or cabinet. The Interlogix TX+PIR Motion Sensor offers a coverage area of 40 feet by 40 feet, as well as pet immunity for small animals weighing up to 80 pounds. Lastly, the Interlogix TX+2WAYFOB is a four (4) button key fob with buttons for arming, disarming, automation, and triggering an auxiliary panic.

We believe these sensors are a must-have for anyone with an Interlogix Simon XTi-5i System. Now you can take full advantage of the encrypted communication that the system offers! If you have any questions or if you want to learn more about these sensors, please reach out to us. The best way to contact us is to email support@alarmgrid.com. We will check your email at our earliest convenience and reply back as soon as soon as we can. We look forward to hearing from you!

Hi DIYers! We are happy to announce that the first 2GIG Encrypted Sensors are available on our site. The lineup includes two contacts, a motion, a key fob, and a glass break. Anyone with a 2GIG GC2e or 2GIG GC3e System will absolutely want to make use of these powerful new sensors.

The new 2GIG eSeries Encrypted Sensors represent perhaps the biggest selling point of the new 2GIG Alarm Systems. These sensors are designed exclusively for use with the 2GIG GC2e and 2GIG GC3e. When enrolled, they will make use of encryption in all their wireless communication. This makes these sensors virtually impervious to any wireless hacking or takeover attempts. This is the best way to ensure that your system is always protected.

It is important to note that you cannot bring these sensors over to the older 2GIG Go!Control GC2 and 2GIG GC3 Systems and expect them to work as non-encrypted wireless sensors. These new sensors can only be utilized as encrypted devices on the GC2e and GC3e Systems. However, you can bring over the older 2GIG Sensors and the Honeywell 5800 Sensors and use them with the GC2e and GC3e as standard 345 MHz sensors.

With that out of the way, let's start checking out the new encrypted sensors!

2GIG DW10e

The 2GIG DW10e is a surface-mounted door and window contact sensor. It offers a super thin profile, with dimensions of 2.59"L x 1.03"W x 0.49"D. This makes the sensor practically invisible when mounted flat on a white surface. There are two programmable loops for the DW10e. One loop will have the sensor operate as a standard contact with a reed switch. The other loop allows you to connect a single Normally Closed (NC) hardwired contact to the DW10e and have it communicate with the panel wirelessly.

2GIG DW20e

The 2GIG DW20e is a recessed door and window contact that is perfect for users who want to achieve a more aesthetically pleasing installation. The sensor and its accompanying magnet need to be inserted into holes that are drilled into the door or window and its frame. The only way to see the sensor after installation is to look at the door or window frame from the side when the door or window is already opened. The DW20e has an impressive 450-foot wireless range when used with direct line of sight.

2GIG PIR1e

The 2GIG PIR1e is a wireless PIR motion detection sensor. The device works by looking for the changes in IR energy that occur with movement. It uses a quad-element PIR sensor for superb reliability. The trustworthy and reliable motion detecting sensor offers a coverage area of 30' by 50'. This is perfect for a home or small business. There are three different sensitivity settings you can choose from. When used on low sensitivity, the device will provide pet immunity for small animals weighing up to 55 pounds.

2GIG GB1e

The 2GIG GB1e is a wireless glass break sensor. The device will effectively monitor plate, tempered, and sealed insulating glass that measures between 1/8 and 1/4 of an inch thick. The sensor listens for both the low-pitched "thud" of an object striking the glass and the higher-pitched "shattering" of the glass itself. This dual-detection process helps to ensure that false alarms do not occur. It is great for monitoring windows for forced entry, but it can also be used with protective glass casings that display products.

2GIG KEY2e

The 2GIG KEY2e is a wireless 4-button key fob that gives you a convenient way to control your GC2e or GC3e while you are on-site. There are dedicated buttons for Arming Away, Arming Stay, Disarming, and activating a relay device. You can also program a dual-button press of the top two buttons (Arm Away and Disarm) to trigger an instant panic. Any button must be held down for a full 2 seconds for the command to go through. This helps to prevent accidental inputs. It has a wireless range of 350 feet.

If you have questions about any of these new 2GIG eSeries Sensors or the 2GIG GC2e and GC3e, or if you just want to learn more about our monitoring service, please reach out to us! We are here to make sure you get the perfect equipment for your needs. The best way to contact us is always to email support@alarmgrid.com. If you want to speak by phone, you can reach us at (888) 818-7728 during our regular business hours of 9am to 8pm EST. We look forward to hearing from you!