Honeywell 5822T Posts

The Alarm Grid holiday buying guide for the 2020 season continues, this time focusing on smart home automation. We will be covering our top picks for lights, door locks, and thermostats. As usual, our selections are compatible with our top security system picks for the 2020 shopping season.

If you haven't seen our earlier 2020 holiday buying guide releases, make sure to review them at some point. They will provide you with a good introduction before checking out our smart home automation offerings.

• Alarm Grid Holiday Buying Guide 2020 for Alarm Panels
• Alarm Grid Holiday Buying Guide 2020 for Security Sensors
• Alarm Grid Holiday Buying Guide 2020 for Environmental Sensors

An automation device is a piece of equipment that you can have activate automatically based on a set schedule. These devices can also be controlled remotely from virtually anywhere in the world using a platform like Total Connect 2.0 or Alarm.com and a simple app on your smartphone. When we talk about automation devices for alarm systems, we are mainly discussing lights that can be turned ON or OFF, dimmer modules that can adjust the brightness of lights, door locks that can be LOCKED or UNLOCKED, and thermostats that can increase or decrease the set temperature in the building when connected with an HVAC system. There are also some miscellaneous automation devices, including smart water valves, that we will also explore. Depending on the platform, you can also integrate these devices with smart home voice assistants like Amazon Alexa and Google Home. We won't be exploring that too much in this buying guide, but it is something to keep in mind if you already have a smart home assistant set up in your house, or if you were considering setting one up in the near future.

To keep our automation section as simple as possible, we will be primarily looking at Z-WAVE PLUS automation devices. This refers mostly to 500-Series Z-Wave Plus devices, though you may occasionally see some newer 700-Series Z-Wave Plus devices thrown in as well. Using certified Z-Wave Plus devices with a Z-Wave Plus controller will ensure the furthest possible wireless range, as well as the longest possible battery life, when applicable. Using exclusively Z-Wave Plus devices on a Z-Wave Plus controller is also the best way to ensure the strongest possible mesh network. Another advantage to going with Z-Wave Plus is that your automation devices will pair directly with your alarm system, which will thereby serve as your central automation controller. This keeps things as simple and as organized as possible, and it will ultimately allow you to keep everything in the same app on your phone.

However, we will also be including a few Apple HomeKit products along the way. We understand that we have many customers who use iOS and are building around the HomeKit platform for automation. When looking at our top security system picks, only the Honeywell Lyric is compatible with Apple HomeKit. This is out recommended system if you are building around the HomeKit platform. If you are starting from scratch and you are not a dedicated iOS user, then you will likely prefer Z-Wave Plus, as you can keep all your system control and automation control in the same app, with virtually no crossover. But, if you have taken advantage of what Apple HomeKit has to offer, and you want to continue building around the platform, then we have you covered. Remember, of our top system picks, only the Lyric can support HomeKit, and even then, your HomeKit devices will not pair directly with the Lyric.

Of our top security system picks for the 2020 holiday buying season, both the Qolsys IQ Panel 2 Plus and the 2GIG GC3e support Z-Wave Plus technology. Both of those systems have their own integrated Z-Wave Plus controller, and they will allow you to take full advantage of what Z-Wave Plus has to offer. However, our other top pick, the Honeywell Lyric only has a classic Z-Wave controller built-in. You can still enroll Z-Wave Plus devices with the Lyric, but they won't offer the same range, battery life, and security provisions as Z-Wave Plus. This makes the Lyric the weak link of the three if automation outside of Apple HomeKit is particularly important to you. But rest assured that every product listed here should work with any of our recommended systems. Its just that you will get the best possible results by using a Z-Wave Plus compatible system, like the Qolsys IQ Panel 2 Plus or 2GIG GC3e.

With all of that out of the way, let's begin exploring our favorite smart home automation devices of the 2020 holiday season.

Smart Lights

Smart lights can be split into a few different categories. They are usually either in-wall modules that replace your existing, standard light switches, or they are plug-in module that you simply plug into a regular wall outlet. Lights can also be split into groups of ON/OFF switches that merely turn the lights ON and OFF, and groups of dimmer modules that can actually adjust the brightness of the lights. As such, you will see four (4) groups of lights listed below. There are in-wall switches, in-wall dimmers, plug-in switches, and plug-in dimmers. We know that may seem a bit confusing, but it should make more sense once you see all of the categories properly laid out and organized. Spoiler, if you're looking for Apple HomeKit Lights, then skip to the very end of this section.

We will start with Z-Wave Plus in-wall switches. These devices replace existing in-wall switches, and they are able to turn the lights ON and OFF. When installing one, make sure to cut power at the circuit breaker first. Then simply remove the existing in-wall switch, and install your new Z-Wave Plus in-wall switch in its place. Keep in mind that most of these units will require the use of a neutral wire. Most homes built in the 1980s onward will have this readily available, though older homes may be lacking this wire. It's also important to mention that all of the in-wall switches listed here should readily fit into single gang brackets. We will also be listing coordinating 3-way switches in the notes section when applicable.

Here are our top picks for Z-Wave Plus in-wall switches.

Next up are Z-Wave Plus in-wall dimmers. These units also replace your existing in-wall switches. The difference here is that these devices have the ability to adjust the brightness of your lights, in addition to simply turning them ON and OFF. You will want to make sure you are using these devices with dimmable light bulbs. Again, you will want to cut power at the circuit breaker when installing. Most of these units will require a neutral wire, though there is an exception here. You should be able to fit these units into a single-gang electrical bracket.

Here are our top picks for Z-Wave Plus in-wall dimmers.

Now we will look at some more DIY-friendly options, starting with Z-Wave Plus plug-in switches. Unlike in-wall switches that you have to install using a screwdriver, these devices simply plug into your standard wall outlet. Just plug one in, connect a lamp, and you now have smart lighting control. These units couldn't be more straightforward and simple to use, and if you're intimidated by having to install your own in-wall light switch, then these are a fantastic alternative. Again, these units are only capable of turning the lights ON and OFF. You can also technically use some of these units with other plug-in devices, provided that the connected device does not exceed the maximum load limit.

Here are our top picks for Z-Wave Plus plug-in switches.

Our penultimate category of smart lights focuses on Z-Wave Plus plug-in dimmers. As you can probably guess, these are plug-in modules, but instead of just turning the lamp ON and OFF, you can also adjust its brightness. The use of dimmable bulbs is recommended. Again, this is an excellent DIY alternative if you don't feel comfortable installing your own in-wall dimmer switch. Just plug it in, connect a dimmable lamp, and enjoy your new smart lights!

Here are our top picks for Z-Wave Plus plug-in dimmers.

Lastly, we want to give special recognition to Apple HomeKit compatible smart lights. We're keeping things simple by only listing products from Lutron. These lights work by building around a centralized base station and then pairing lighting modules with that main unit. Our team at Alarm Grid is wholly impressed by what Lutron has to offer, and we can definitely recommend these lights for anyone building around the HomeKit platform. One other major benefit of Lutron Smart Lights is that no neutral wire is required as part of the setup. This can be very beneficial if you do not have a neutral wire in your home's existing electrical wiring. Please note that Alarm Grid only offers the Caseta lineup from Lutron, so that is what we will be focusing on in this buying guide.

The Lutron section of this guide will be split into four (4) categories. First we will look at the smart bridges, or central hubs, that we offer for Lutron. Then we will explore some bundled deals we offer as starter kits. From there, we will check out individual Lutron lighting devices. Lastly, we will examine some accessories for Lutron devices.

First up, we have the Lutron Smart Bridges. There are only two (2) here. You need one of these devices to start building a network of Lutron Smart Lights. You will notice a standard "non-Pro" model, as well as "Pro 2" model. The main difference here is that the "Pro 2" model can integrate with Alarm.com, while the "non-Pro" model cannot. This is completely irrelevant if you are building a HomeKit network around the Honeywell Lyric, as you will be using Total Connect 2.0 as your interactive smart platform instead of Alarm.com. But if you are using HomeKit separately with an IQ Panel 2 Plus, a 2GIG GC3e, or pretty much any other Alarm.com Security System, then this can really come in handy, as you can then integrate your smart lights in with the same network as your alarm system.

Here are our Lutron Smart Bridges.

But before you rush out and buy one of the aforementioned Lutron Smart Bridges, you may instead consider getting one of our Lutron Starter Kits, which all include a Lutron Smart Bridge and some compatible devices to get you started. This can save you a bit of money if you are just getting started with Lutron. Unfortunately, we only have starter kits based around the "Non-Pro" smart bridge. If you are wanting the "Pro 2" model for Alarm.com use, then you will need to buy that model ala carte, along with all the devices you want to pair.

Let's check out our Lutron Starter Kits.

Now we'll look at the actual Lutron Lighting Components. These are the individual, ala carte lighting devices that you pair with your Lutron Smart Bridge. The included notes should help you decide which devices are right for your Lutron network. Lutron keeps things relatively simple here, as the selection is short but sweet.

Here are individual Lutron Lighting Components.

Last but not least, we have some Lutron Accessories. These include the Pico Remote that you can use a remote control for your Lutron Lights, as well as various wall-plates and some bundles. There are quite a few accessories to cover, and they make the perfect stocking stuffer for the Lutron lover on your gift list.

Here are Lutron Accessories.

Door Locks

Door locks are fairly straight forward. They replace the existing deadbolt lock on your front door, back door, patio door, pool door, garage door, or really any door with a deadbolt lock. You will then have smart control over that door, meaning you can LOCK and UNLOCK it remotely using a compatible interactive service platform. This also includes the ability to have the door LOCK or UNLOCK automatically with smart scenes. Most of the locks listed here will allow you to use a traditional key if you want, but you can also manually enter a code into the lock using push-buttons or a touchscreen. This can be very convenient for getting in if you forget your key or don't wish to carry one around.

Virtually any door lock will accomplish the same goal, so what you should base your buying decision on is how reliable the brand is, how you control the door lock locally (e.g. a push-button touchpad or a LED touchscreen), and which design you like. You will also need to decide whether you need a Z-Wave Plus door lock or an Apple HomeKit door lock. Most of the models listed here are Z-Wave Plus variants, but we did include a couple of HomeKit versions for good measure. Many of the door locks listed here come in multiple finishing options to give you some added customization. You will notice that we do not list too many brands here. We really wanted to focus on the ones we feel the most confident in offering.

Here are our top picks for door locks.

Smart Thermostats

Now we're really getting into exciting territory, as smart thermostats allow you to control the temperature in your home from virtually anywhere! This is perfect whether you want to keep energy costs low, or you simply want to ensure you arrive home to a comfy house. We all know how stressful it can be if you forgot to adjust your thermostat before leaving home. Well, now you can worry no longer! All you need to do to get started is cut the power at the breaker for your HVAC system, remove your old thermostat, and install your new smart thermostat in its place. This is easier than you might think! For this category, we will mostly be covering Z-Wave Plus thermostats, but we did include an Apple HomeKit thermostat in the listings as well.

Here are our top picks for smart thermostats.

Other Smart Home Devices

Alright, we're finishing this up with some great smart home devices that we couldn't really fit into any other category. Our main focus here will be on smart garage door controllers and smart water valves. These are super convenient and useful devices that make a great addition to almost any home. A smart garage door controller connects with your existing garage door motor so that you can open and close your garage door from anywhere or have it open and close automatically with smart scenes. Smart water valves are an excellent emergency tool that you can use to shut-off your water supply in the event of a flood or leak. Many users will pair them with flood sensors for inclusion in smart scenes. Unfortunately for Apple HomeKit users, we don't have any HomeKit devices for this section, and we will only be covering Z-Wave variants in this section.

Check out these miscellaneous smart home devices!

Reach Out to Us!

Got any questions about which smart home devices are right for you, or are you not sure about compatibility? Reach out to us! Our team is happy to help you make your holiday shopping season as easy and as stress-free as possible. The best way to contact us is to email support@alarmgrid.com. We check our email from 9am to 8pm ET M-F. And as always, we look forward to hearing from you!

Alarm Grid has discovered a recent manufacturing mistake that has affected some Honeywell 5822T Garage Tilt Sensor units. The issue has resulted in the internal tilt detector for the affected units being positioned upside-down. We apologize to anyone who may have received an affected unit.

Inside every Honeywell 5822T is a pair of cylindrical metal pieces. These metal pieces represent the sensor's internal tilt detector that is used to determine whether the garage door that is being monitored is opened or closed. Because of a recent manufacturing error, the internal tilt detector for these sensors was positioned upside-down.

The following picture shows the tilt detection sensor in the proper position. Note how it is positioned facing the upper portion of the sensor.

And now here is a picture of a Honeywell 5822T where the tilt detector has been positioned improperly. Note how the metal cylindrical pieces are positioned facing the sensor's bottom.

At this time, we are not entirely sure of the date ranges for the affected sensors. So far, we have only seen incorrectly manufactured Honeywell 5822T units with a date code of D227, which represents August 14, 2020. We have also seen newer Honeywell 5822T units with a date code of D255, which represents September 11, 2020 that do not have this issue. Based on that info, it's likely that Resideo has already corrected the mistake in manufacturing, and we are only just now discovering the issue due to reports from customers.

Below is a picture of the date code for one of the improperly manufactured 5822T units. Note that D represents the year 2020, while 227 represents the 227th day of the year, or August 14th, with 2020 being a leap year.

The good news is that the improperly manufactured units are still usable. When using the 5822T as a garage tilt sensor (Loop 3), you just need to mount the unit upside-down so that the internal tilt detector is facing the proper direction. Normally, these devices are mounted at the top of the garage door with the arrow pointing upward. If you find that you have an affected unit, just mount the sensor in the same location with the arrow pointing downward. If you are only using the Honeywell 5822T as a wireless transmitter (Loop 1), then you can position it in any direction, as that function is unaffected by the manufacturing error.

The picture below shows the arrow on the outside of the Honeywell 5822T. The sensor is typically installed with the arrow facing upward, but an affected unit can be used for regular operation by being installed with the arrow facing downward.

If you have any questions about the Honeywell 5822T, please reach out to us by emailing support@alarmgrid.com. This is also a great email to use if you are interested in starting monitoring service with Alarm Grid. We check our email from 9am to 8pm ET M-F. We look forward to hearing from you!

A great way to build out your Honeywell Lyric is with Honeywell 5800 Sensors. These are simple, 345 MHz wireless sensors that you can easily enroll with the system for security, life-safety, and environmental monitoring. They are perfect for expanding your system and making it more robust.

When you want to pair a Honeywell 5800 Sensor with the Lyric, the process is very straightforward. Put the Lyric in its auto-enrollment mode by choosing Security > Tools > enter Installer Code (default 4112) > Program > Zones > Add New > Serial Number. Make sure the RF Type on the right-hand side is set to 5800. Then activate the sensor either by faulting it or triggering its cover tamper switch. The Lyric should beep to confirm that it received a signal transmission. Then activate the sensor a second time to have the Lyric display the Serial Number. The third activation will confirm the Serial Number and return you to the screen where you can configure the zone settings.

Programming the zone settings for the sensor is actually quite simple. Depending on how you enrolled the sensor, you may need to adjust the Loop Number. This is almost always the case if you enrolled the sensor by activating its tamper switch. Refer to the instruction manual for the 5800 Sensor to determine which Loop Number to use.

The two (2) Zone Descriptors and the Device Type serve as the name for the sensor. You should choose a name that will help you identify the sensor, e.g. "Front Bedroom Motion Sensor", "South Hallway Door", etc. The Response Type determines how the system responds when the sensor is faulted. See our list of Lyric Response Types for more info.

Alarm Report should be set to Yes if you want the system to report out through AlarmNet to a Central Station if the zone causes an alarm on the system. That is an essential component of alarm monitoring services. Chime is optional, and it has the panel emit any one of several available sounds when the zone is faulted. Supervision tells the panel to look for an RF check-in signal from the sensor periodically to ensure that it is online. Click Save in the bottom-right after you finish adjusting the settings.

Keep in mind that only uni-directional (one-way) sensors from the Honeywell 5800 Series can be used with the Lyric. This leaves out bi-directional devices like the Honeywell 5800WAVE Siren, the Honeywell 5828 Keypad, and the Honeywell 5800RL Relay Module, so make sure you do not buy those for the Lyric. But you still have a lot of excellent sensors and security devices to choose from.

Below is a list of the Honeywell 5800 Sensors that you can use with the Honeywell Lyric:

Sensor Name	Notes
Honeywell 5800MINI	Door/Window sensor. Uses Loop 1.
Honeywell 5800PIR-RES	PIR motion sensor. Uses Loop 1. Coverage Area: 35' x 40'
Honeywell 5816	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5811	Door and window sensor. Uses Loop 1.
Honeywell 5800C2W	9-zone wired to wireless converter. Allows hardwired sensors to communicate with the Lyric as wireless devices. All zones use Loop 1 and a unique Serial Number ID.
Honeywell 5800CO	Carbon monoxide sensor. Loop 1 = CO Detection Loop 2 = End of Sensor Life (separate programming only required on TURBO and other V-Plex panels)
Honeywell 5800COMBO	Combination, smoke, heat, CO, and low-temperature sensor. Uses up to five (5) zones on the Lyric Panel. Has two (2) Serial Numbers for enrollment purposes. Loop 1, SN 1 = Smoke/Heat Detection Loop 2, SN 1 = Smoke/Heat Maintenance Loop 3, SN 1 = Low Temperature Detection Loop 1, SN 2 = CO Detection Loop 2, SN 2 = End of Sensor Life (separate programming required only on TURBO and other V-Plex panels)
Honeywell 5800FLOOD	Flood and temperature sensor. Loop 1 = Low Temperature Detection Loop 2 = High Temperature Detection Loop 3 = Flood Detection
Honeywell 5800MICRA	Recessed window sensor. Uses Loop 1.
Honeywell 5800PIR	PIR motion sensor. Loop 1 = Low Sensitivity Motion. Loop 2 = High Sensitivity Motion. Loop 3 = Low Temperature Detection Coverage Area: 35' x 40'
Honeywell 5800PIR-COM	Commercial PIR motion sensor. Loop 1 = Low Sensitivity Motion Loop 2 = High Sensitivity Motion Loop 3 = Low Temperature Detection Coverage Area: 60' x 80'
Honeywell 5800PIR-OD	Outdoor PIR motion sensor. Uses Loop 1.
Honeywell 5800PIR-OD2	Outdoor PIR motion sensor. Uses Loop 1.
Honeywell 5800RP	Wireless repeater for Honeywell 5800 Sensors. Does not require enrollment, but can be assigned a single zone for RF supervision, low-battery, AC loss, and RF jam detection. This is done using Serial Number 1 with Loop 1, with DIP Switch 2 set in the OFF position. Can also use up to four (4) separate zones for supervision when DIP Switch 2 is set to ON. This is required for UL installations.
Honeywell 5800RPS	Recessed door/window sensor. Uses Loop 1.
Honeywell 5800SS1	Shock sensor. Uses Loop 1.
Honeywell 5802MN	Medical alert button. Uses Loop 1.
Honeywell 5802MN2	Medical alert button. Uses Loop 1.
Honeywell 5802WXT	Panic button. Uses Loop 1.
Honeywell 5802WXT-2	Panic button. Uses Loop 1.
Honeywell 5806W3	Smoke detector. Uses Loop 1.
Honeywell 5808W3	Smoke and heat detector. Loop 1 = Smoke & Heat Detection Loop 3 = Low Temperature Detection
Honeywell 5809	Fixed temperature and rate-of-rise heat detector. Uses Loop 1. Alarm occurs when the temperature exceeds 135 degrees Fahrenheit, or when the temperature rises more than 15 degrees Fahrenheit per minute.
Honeywell 5809FXT	Fixed temperature heat detector. Uses Loop 1. Alarm occurs when the temperature exceeds 135 degrees Fahrenheit.
Honeywell 5809SS	Fixed temperature and rate-of-rise heat detector. Uses Loop 1. Alarm occurs at 135 degrees Fahrenheit or when the temperature rises more than 15 degrees Fahrenheit per minute.
Honeywell 5814	Door and window sensor. Uses Loop 1.
Honeywell 5815	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5816MN	Door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switches
Honeywell 5816OD	Outdoor door and window sensor. Loop 1 = Terminal Block for NC Contact Loop 2 = Reed Switch
Honeywell 5817	Three (3) zone door and window sensor & transmitter. Loop 1 = NC or NO (DIP Switch Selectable) unsupervised. It does not use an End of Line Resistor (EOLR) Loop 2, 3 = NC Only. Both are unsupervised with no EOLR used
Honeywell 5817CBXT	Three (3) zone commercial transmitter. Loop 1 = Two (2) Terminals; Primary Loop supervised by 470k Ohm (yellow, purple, yellow, gold) EOLR. Resistor must ALWAYS be installed, even if Loop 1 is not programmed. If Loop 1 is used as a burglary zone, then Loop 4 must be programmed as a separate zone for Cover Tamper protection. Loop 2 = NC Reed Switch Loop 3 = Two (2) Terminals; NC Loop unsupervised, no EOLR required
Honeywell 5817XT	Three (3) zone door and window sensor & transmitter. Loop 1 = NC or NO (DIP Switch Selectable) unsupervised with no EOLR required Loop 2, 3 = Two (2) Terminal Blocks, NC Only
Honeywell 5818MNL	Recessed door and window sensor. Uses Loop 1. Not suitable for use in metal doors
Honeywell 5819	Three (3) zone shock processor. Loop 1 = NC for Inertia Style External Shock Sensor. This input provides a suitable fast loop response of from 1ms to 20ms, based on dip switch setting Loop 2 = Reed Switch Loop 3 = NC for Wired Contact, unsupervised with no EOLR required
Honeywell 5819S	Shock sensor and contact sensor. Loop 1 = Built-in Inertia Style Shock Sensor Loop 2 = Reed Switch Loop 3 = NC for Wired Contact
Honeywell 5819WHS	Three (3) zone shock processor. Loop 1 = NC, Built-in Inertia Style Shock Sensor Loop 2 = Reed Switch Loop 3 = NC for Wired Contact
Honeywell 5820L	Slimline door and window sensor. Uses Loop 1.
Honeywell 5822T	Garage tilt sensor. Loop 1 = NC for Wired Contact, unsupervised, no EOLR used Loop 3 = Tilt Switch
Honeywell 5834-2	Two (2) button key fob. Dual-button inputs allowed. Uses three (3) loops total, for a possible three (3) inputs. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5834-4	Four (4) button key fob. Dual-button inputs allowed. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5834-4EN	Four (4) button key fob. Dual-button inputs allowed. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible. Can only be used with the Lyric in Low-Security Mode (Green LED)
Honeywell 5853	Glass break sensor. Uses Loop 1.
Honeywell 5869	Commercial panic switch. Uses Loop 1. Latches when tripped, key (provided) needed to reset it after it is tripped
Honeywell 5878	Six (6) button key fob. Uses two (2) Serial Numbers, which both use Loops 1, 2, 3, 4. Up to eight (8) inputs possible.
Honeywell 5898	Dual-tec motion sensor. Loop 1 = Low Sensitivity Motion Sensor. Pet immunity is available for this loop. 50lb or 100lb pet immunity, selectable via DIP Switch 1 Loop 2 = High Sensitivity Motion Sensor. Loop 3 = Temperature Sensor (High or Low, DIP Switch Selectable)

With a new year comes reduced pricing on many of our great existing products. We have just dropped the prices on 73 of our existing offerings. You can certainly find something great to upgrade your existing system or use with a new installation. Let's check out these awesome products!

Before we go through and list each and every reduced price product, we figured we'd go through and talk about some of the ones that excite us the most. After all, sorting through a list of 73 products is pretty daunting. Our initial "best-of" list may help you find exactly what you're looking for. These products are great if you have an existing system, or if you are building a new system and want to add some cool accessories.

These products are presented in alphabetical order:

Alarm.com ADC-V723 Outdoor Camera

The ADC-V723 is the current flagship outdoor security camera for use with the Alarm.com platform. This simple, yet powerful camera makes the perfect addition to any home or small business. It can capture video at up to 1080p quality, and it makes use of High Dynamic Range (HDR) to improve image depth and luminosity.

Alarm.com T2000 Smart Z-Wave Thermostat

If you are still looking for a smart Z-Wave thermostat, then the ADC-T2000 is an outstanding entry-level option. It conveniently wires in place of your existing thermostat to give you smart control over your HVAC system. It can pair nicely with both the Alarm.com and Total Connect 2.0 platforms. You just need a compatible Z-Wave hub to get started.

DSC PG9312 Outdoor Door/Window Sensor

The DSC PG9312 is the premier outdoor contact sensor for any user with a PowerG-compatible security system. It offers a maximum magnet spacing gap of 1.75", which gives you more flexibility in choosing a location for the sensor and magnet. Like all PowerG Sensors, it offers a wireless range of up to 2 km away from the panel, as well as 128-bit AES encryption.

DSC PG9914 Motion Sensor

Anyone with a PowerG Security System looking to add a basic indoor motion sensor should turn to the DSC PG9914. This is a simple, yet effective motion sensor that is great for use in nearly any home or business. It offers a modest coverage area of 39 feet, and the sensor provides pet immunity for small animals weighing up to 85 lbs.

Encore FireFighter FF345 Smoke/CO Listening Module

The Encore FireFighter FF345 is perfect if you have existing high-voltage smoke detectors that you want to integrate into a 345 MHz wireless system. The module can detect both the Temporal 3 sound of an activated smoke detector and the Temporal 4 sound of an activated CO detector. And if your high-voltage devices are one-go-all-go, then a single FF345 can takeover your entire network.

Honeywell 5822T Garage Door Tilt Sensor

Also for 345 MHz system users, the Honeywell 5822T allows your system to monitor your garage door to see if it's opened or closed. This wireless sensor works great for security and automation purposes alike. You might even create a special smart scene that activates as soon as the 5822T detects that you garage door has been opened!

Honeywell IPCAM-WIC1 Indoor Camera

The Honeywell IPCAM-WIC1 Indoor Camera is for anyone with an existing Total Connect 2.0 Video Monitoring service plan that they want to expand upon. This is a simple and straightforward camera that captures video at up to 720p quality. It can be easily rested on a desk or table, and no hard-mounting is required.

Qolsys IQ DW MINI-S Door/Window Sensor

The Qolsys IQ DW MINI-S can be used by anyone with a 319.5 MHz wireless system, including the Qolsys IQ Panel 2 Plus w/ Legacy Interlogix & Qolsys Daughtercard. This is a straightforward door and window contact sensor that makes a nice addition to any compatible system. Its small and compact design allows for a tidy installation.

Please see our complete list of reduced price products in the table below, organized by product type:

If you have any questions about these products or any of the other products on our site, including product compatibilities, please reach out to us. You may also contact us if you want to learn more about our monitoring services. The best way to reach us is to email support@alarmgrid.com. Or you may call us at (888) 818-7728. Remember that our support hours run from 9am to 8pm ET M-F. We look forward to helping you find the perfect product for your needs!

With the holiday season quickly approaching us, we thought it was a good time to present some holiday buying guides for various security systems. Today, we are focusing on the Honeywell Lyric. This guide will help whether you are considering a new Lyric or adding upon an existing one.

The Honeywell Lyric is currently the flagship all-in-one wireless security system from Resideo. It has been one of the most highly regarded alarm systems for the past few years for several reasons. The system supports up to 128 wireless zones, making it suitable for applications big and small. It has a built-in Z-Wave controller, and you can pair up to 72 Z-Wave devices for home automation purposes. The Lyric is also one of the very few alarm panels that can support Apple HomeKit, making it perfect for iOS users looking to expand upon their HomeKit Network. In fact, we believe that the Lyric is the top HomeKit Security System on the market at this time.

The other major appeal of the Lyric is the fact that it can technically be monitored using an IP only communication path. This is because it connects with AlarmNet360 and the Total Connect 2.0 platform. Unlike most other monitoring platforms like Alarm.com which require cellular connectivity, Resideo allows IP only monitoring for panels connected with TC2. The Lyric has a built-in WIFI card, so you can connect with a local network right out of the box. Although we always recommend cellular communication for optimal reliability, we do understand that many users will want to use IP only service as a cost-cutting measure. Additionally, you can always add a cellular communicator to the Lyric System if you decide that you want to go cellular later on. Both the Honeywell LYRICLTE-A (AT&T LTE) and the Honeywell LYRICLTE-V (Verizon LTE) are great options.

Building a Lyric System from Scratch

For new users starting from scratch, the best option is typically to buy a complete Honeywell Lyric Security System Kit. This will include everything you need to get started with alarm monitoring. Whether you plan to use IP only monitoring service, or you intend on setting up cellular service, there is a perfect kit for you. For those planning to go IP only, no cellular communicator is needed, and you should choose a kit labeled "WIFI Only". If you intend to use the system for cellular monitoring, then both AT&T and Verizon system kits are available. Whether you go with a 3-1 kit (3 contacts and 1 motion) or a 10-1 kit (10 contacts and 1 motion) should depend on the size of the building you are monitoring. You will need more contacts to cover more doors and windows.

We recommend going through the Lyric System Kit Page linked above and finding the perfect Lyric Kit for your needs. In addition to the system, sensors, and optional communicator, you will also get a Honeywell LT-Cable with every kit. This makes it super easy to get the system up and running without having to prepare any standard alarm wiring.

Sensors for New and Existing Lyric Systems

One of the best aspects of the Lyric is that it has one of the most diverse and complete lineup of supported sensors in the entire security industry. Resideo created a sensor lineup designed exclusively for their Lyric System in the Honeywell SiX Series Sensors. These powerful sensors offer an impressive communication range of up to 300 feet indoors and 128-bit AES encryption for enhanced wireless protection. The lineup includes the following products:

• SiXCT Door/Window Contact
• SiXMINICT Mini Door/Window Contact
• SiXPIR Motion Sensor
• SiXGB Glass Break Detector
• SiXSMOKE Smoke Detector
• SiXCOMBO Combination Smoke/CO Detector
• SiXSIREN Wireless Siren
• SiXFOB Wireless Key Fob

With this great lineup, you can achieve a total and complete Lyric Security System by only using SiX Series devices. And for most Lyric users, that is the best option. But these are not the only sensors you can use with the Lyric System. The Lyric is also compatible with nearly any uni-directional 345 MHz sensor, which includes most devices from the Honeywell 5800 Series and the 2GIG 345 MHz lineup. Additionally, these lineups are both a little more fleshed out than the SiX lineup. There are certain sensor types (e.g. outdoor sensors) where you will need to turn to one of these product lineups.

Many users will also supplement their SiX Series devices with Honeywell 5800 Sensors and 2GIG 345 MHz Sensors as a cost-saving measure. These 345 MHz sensors will work just as well as the SiX Series devices on the Lyric. The only difference is that the 345 MHz sensors will not utilize any encryption, making them more susceptible to wireless attacks. The Lyric does have protection against 345 MHz RF jamming, but it can offer some users better peace of mind to know that their wireless sensors are encrypted. But if you are comfortable using non-encrypted wireless devices, then 345 MHz sensors can save you a lot of money when designing your Lyric System.

Some of our favorite Honeywell and 2GIG 345 MHz Sensors for use with the Lyric include:

• VERSA-2GIG Door/Window Contact
• 2GIG DW20R Recessed Door/Window Contact
• Honeywell 5816OD Outdoor Door/Window Contact
• Honeywell 5800PIR-OD Outdoor Motion Sensor
• Optex FTN-RRHW Outdoor Motion Sensor
• Honeywell 5822T Garage Tilt Sensor

Other Accessories for Your Lyric

We have already covered the sensors you will use with your Lyric System. However, there are still other devices you may want to add to your setup. The biggest attraction are Z-Wave devices like lights, door locks, and smart thermostats. One admitted weakness of the Lyric is that its automation controller is only a standard Z-Wave controller. The Lyric does not offer a Z-Wave Plus controller, and Lyric users cannot take advantage of the extended range and increased battery life of Z-Wave Plus. You can still use Z-Wave Plus devices with the Lyric System, but they will only offer the functionality of classic Z-Wave peripherals.

With that limitation in mind, you can still use the Lyric as a perfectly capable smart home automation hub. You can even pair the system as a secondary controller to other automation hubs (e.g. Samsung SmartThings) for added flexibility in your smart home. Nearly any Z-Wave automation device can be used with the system, so feel free to explore your options. We have plenty of devices on our website. Just remember that the Lyric System cannot support Z-Wave security devices. The Lyric Z-Wave controller is for automation purposes only. Alarm Grid does not sell Z-Wave security sensors on its website.

If you want to use your Lyric to control your garage door, then you will want to invest in a Honeywell 5877GDPK. This kit includes everything you need to get started with garage door operation for your Lyric System. Inside the kit there is a Honeywell 5877 Z-Wave Garage Door Relay, a Honeywell 5822T Garage Door Tilt Sensor, and a FortrezZ Z-Wave Siren/Strobe. You can purchase these items separately, but this convenient kit makes things easier.

The Lyric has only one compatible wireless keypad option, which is the Honeywell LKP500. This is a fairly standard push-button keypad with an LCD screen. You might also consider getting a cheap tablet and mounting it to the wall and using that as a keypad. You can download the Honeywell My Home Controller App to the tablet and essentially make the device a permanently mounted touchscreen keypad for your Lyric.

Lastly, you might want to get a desk mount for your Lyric System. This will eliminate the need for mounting the panel to the wall. Desk mounts are great for people living in apartments or rental homes, as well as users who simply do not want to drill holes. Using a desk mount sure beats laying the system flat on a counter! The Lyric Desk Mount is called the Honeywell LCP500-DK. There is also a desk mount for the Honeywell LKP500 Lyric Keypad called the Honeywell LKP500-DK.

Ask Us Questions!

Don't be afraid to reach out to us at Alarm Grid if you have any questions about the Lyric, or if you need any help choosing a system and accessories. The best way to reach us is to email support@alarmgrid.com. You may also reach us over the phone at (888) 818-7728. Remember that our support hours run from 9am to 8pm ET M-F. We look forward to hearing from you!

Hi DIYers! Many of our customers have been using Chamberlain and LiftMaster MyQ Garage Door Controllers with Total Connect 2.0. These smart garage door controllers are perfect for use with the TC2 platform. They offer a great way to integrate your garage door into your smart home network.

The Chamberlain and LiftMaster MyQ integration is great for tying in remote control for your garage doors to your Total Connect 2.0 account. By using this integration, you can consolidate your garage door control into one single app, instead of two separate ones. However, there is a limitation. The integration does not allow you to add the MyQ garage doors into a TC2 Smart Scene for automated control based on security system actions. For instance, you cannot create a scene that will automatically disarm your Resideo System if your garage door is opened. But fortunately, we now have a solution for this problem.

When you integrate your MyQ Garage Door Controller in with Total Connect 2.0, you can control your garage door remotely through the platform. You can also receive text and/or email alerts when the garage door opens or closes. However, if you try to integrate your MyQ Controller with smart scenes, you will be unable to do so. But we recently came up with a solution for this issue that will work for the Lyric Controller and all LYNX Touch Systems. This solution will also provide your system with the ability to truly monitor the activity of your garage door.

The answer is to add a sensor to your garage door. You will want to use either a tilt sensor or a contact sensor with a wide spacing gap. The Honeywell 5822T is a wireless tilt sensor that can easily pair with a Lyric or LYNX Touch System. Another option is the Honeywell 958. This is a hardwired contact designed for overhead garage doors. You can either wire the Honeywell 958 back to the panel, or you can connect it to a wireless sensor that accepts a wired input, such as a 5816 or a SiXCT. Whether you go with the 5822T or the 958 is really up to you, as they are both perfect options for this job.

You should program the sensor into one of the designated wireless garage door zones. The designated garage door zones for an L5100, L5200, or L5210 are Zones 46 thru 48. For an L7000, they are Zones 45 thru 48. And for the Lyric, they are Zones 127 thru 130. You should give the Zone Descriptor a name that allows you to easily recognize it as your garage door.

Please note that each garage door zone is associated with a particular garage door slot. The table below outlines this:

From there, you should program a "virtual" Honeywell 5877 Relay Module into the system through the Automation Menu. The 5877 is a Honeywell Wireless Relay Module that provides remote control for garage doors. However, it is not compatible with MyQ Garage Door Controllers. With this trick, you don't actually need a 5877 Relay, but you will program your system as if you are using one.

What you want to do is start from the main screen of your panel. Choose Automation > down arrow > Garage Door Setup. From there, choose the garage door slot associated with the zone you set up with the tilt sensor or the contact sensor. Click on "Assign Device". Then go to the "Enter Serial Number" field. Since you aren't actually using a real 5877, you can just enter a fake serial number like "1111111". Click "Done" in the bottom-right corner when you have finished. This will make the system think that a 5877 Relay has been enrolled. You can then return to the main screen by repeatedly pressing the return arrow in the upper-right.

You can then create TC2 Smart Scenes to have the system respond automatically based on the status of the garage door. For example, you might have a smart scene to disarm your system automatically when you open your garage door. To do this, you will want to use the garage door slot that you set up on the system when creating the smart scene. The system will know to change the status of the garage door (opened or closed) based on the activity of the associated zone.

Now, you might be wondering why you need the "fake 5877" setup with the system. The reason for that is because you can't create smart scenes to Arm or Disarm your system based on zone faults. So even if you have sensor programmed for your garage door, you cannot use it as a trigger for arming or disarming your system. But you can use a garage door as a trigger. By making your system think that it has a true garage door programmed, you can use that as a trigger for smart scenes.

It must be mentioned that there are a couple of limitations to this setup. For one, you cannot use this work-around to have your garage door respond automatically based on system activity. This is because there is no real relay module to tell the garage door what to do. So if you want to have the garage door automatically open/close when you arm/disarm your system, it will not work. Second, this will not work with Honeywell VISTA Systems, as those systems do not support the 5877. As a result, you cannot program a "fake 5877" on a VISTA Panel. But other than these limitations, this is a pretty good work around. You also get the benefit of enabling your system to truly monitor your garage door for activity.

If you have any questions about this work-around, please reach out to us. The best way to contact us is to email support@alarmgrid.com. We will check your email at our earliest convenience and respond as soon as possible. We look forward to helping you.

We strive to have some of the best pricing on the internet for security products. When prices are reduced for us, we do our best to quickly pass off those savings to anyone who has made a purchase here.

In the last week, we have reduced the prices on over 100 items an average of 6%. Our Lyric kits have all seen price reductions between 6% and 19%.

Below is the list of all items whose price has been reduced. We hope you enjoy the savings!