News Posts

Update 09/18/23: Qolsys has released this firmware as of today. Alarm.com, however, has not yet made it available for dealers to perform remote OTA updates. They usually lag behind Qolsys by a few days, as they perform their own testing. Instructions for updating using a patch tag can be found here. The full Qolsys TSB can be found here.

Original Blog Post:

We've been hearing about it for a while, and Firmware 4.4.0 will be available any day now. In this post, we'll go through some of the big additions, fixes, and improvements that you can expect to see in this release. From support for PowerG automation devices to the addition of Night arming.

This is one of the most ambitious updates for Qolsys that we've seen. There are a lot of new features in this update. There are also some important fixes and improvements included. In this post, we'll go through what we believe are some of the more important changes coming up in Firmware 4.4.0.

New Features:

• Support for All New PowerG Automation Devices:
  • IQ Lock-PG
  • IQ Dimmer-PG
  • IQ Switch-PG
  • IQ Smart Socket-PG
  • IQ Smart Plug-PG
  • IQ Outdoor Plug-PG
• Added a new Automation Icon within the Installation > Devices Menu. This icon is where you will now go to add everything except Z-Wave Automation devices. However, from within this screen, you can reach Z-Wave Automation (if you navigate here in error). In the future, we expect all Automation will be programmed from within this screen.
• Added "Night Arming" mode. The panel can now be armed in "Away", "Stay", or "Night".
• Created a new PIN code setting for users of the IQ WIFI 6. This will restrict access to the profiles and network map settings of the router.
• Added support for Aeotec Indoor Siren 6.
• Added Sensor Group 11 (Day Zone) and Group 21 (Night Motion).
• Added Sensor Groups 61 (Fixed Intrusion Panic) & 62 (Fixed Silent Panic). With these settings, hardwired, latching panics can now send restore signals when they are physically restored.
• Allows exterior PowerG motions to be programmed as Door/Window sensors to expand the Sensor Group options when programming.
• Added the option to display ambient temperature on the IQ Panel 4 and IQ4 Hub screen when used with PowerG and PowerG Plus devices that support reporting ambient temperature (listed below).
  
  
  • PG9312
  • PG9309
  • PG9200AX
  • PG9350SL
  • PG9914
  • PG9862
  • PG9872
  • PG9984P
  • PG9922
  • PG9936
  • PG9933
  • PG9905
  • PGP9945E
  • PGP9922
  • PGP9920
• PowerG Smoke Detectors can now sound different cadences for Intrusion, Fire, and CO alarms when the "PowerG Smoke Detector Siren" option is used for additional sounders.

Before going on to Fixes and Improvements, I wanted to pause for a moment and expand a bit on a couple of the things listed above. With the new Sensor Group 11 (Day Zone) here is the description of operation for that zone type: Intended for a Door or Window zone that triggers an alarm instantly if the system is armed (same as Group 13). When the panel is disarmed, the zone will annunciate Opens AND Closes, and will continue to notify until the Dismiss button is pressed on the panel screen.

When it comes to Night Arming, an understanding of the Groups associated with motion detectors is essential. Below is an explanation of how each Sensor Group operates. All of these Groups are supervised.

• Group 17, Away-Instant Motion: Active only when armed to "Night" or "Away". Trips instantly when motion is detected. Does not trip if an E/E zone is tripped first.
• Group 15, Stay-Instant Motion: Active in "Stay," "Night," and "Away". Trips Instantly when motion is detected. Does not trip if an E/E zone is tripped first.
• Group 35, Stay-Delay Motion: Active in "Stay," "Night," and "Away" modes. Triggers an Entry Delay if motion is faulted. Does not trip if an E/E zone is tripped first.
• Group 20, Away-Delay Motion: Active when armed to "Night" and "Away". Triggers an Entry Delay if triggered first. Does not trip if an E/E zone is triggered first.
• Group 21, Night Motion (New): Active only when armed to "Away" and trips instantly when motion is detected by this sensor first. Does not trip if an E/E zone is tripped first.
• Group 25, Safety Motion: This sensor does not report or trigger an alarm. This is a "Chime-Only" sensor when "Activity Monitoring" is active, regardless of panel armed status. Used for medicine cabinets, storage, activity tracking, etc.

Panel Fixes and Improvements:

• Changed the Z-Wave naming convention for Settings related to Automation.
• Added support for Z-Wave Weiser/Kwikset Lock supervision requests.
• Made improvements to text size and movement in Photo Frame Screensaver.
• Enhanced the downloading of images and videos from the IQ Panel to a mobile device.
• Added a 30-second arming delay for the IQ Panel 4's built-in glass break detector.
• Fixed an issue with pairing the ADC S2000-T Temp Sensor to the panel.

IQ Remote PowerG Fixes and Improvements:

• Added the ability for the IQ Remote PowerG to automatically power back on after an extended power failure/battery drain, once primary power is restored.
• Corrected an issue where "Nighttime Mode" was not working properly on the IQ Remote PowerG.
• Changed the functionality of the Power Button on the IQ Remote PowerG. Power Down/Reboot now requires a 10-second button press.
• Added support for Thermostats and Garage Door Control to the IQ Remote PowerG.
• Added "Weather Clock" to the IQ Remote PowerG Frame Options.
• Weather to the IQ Remote PowerG now functions when paired in both PowerG and WIFI modes.
• Added support to IQ Remote PowerG for "Installer Test Mode" where the siren is temporarily silenced during testing.
• Added support to the IQ Remote PowerG for Doorbell Notification pop-up and chime, when paired over both PowerG and WIFI.
• IQ Remote PowerG enrolled over PowerG will now automatically upgrade upon first enrollment, rather than waiting 24 hours.
• General communication improvements (Sync/Delay).

Update Instructions:

This firmware is now available, so you can perform the update. Your panel must be on Firmware Version 4.3.0+ before upgrading to 4.4.0. To check your firmware version, tap the gray bar at the top of the panel's home screen, then press Settings > Advanced Settings > Enter Installer or Dealer Code (1111 or 2222 respectively) then tap About > Software.

If your panel is on Firmware Version 4.0.0, 4.0.1, or 4.1.0, you must first update to 4.1.1.

From there, you can update to 4.2.0 or 4.2.1. Then you can update to 4.3.0 and finally to 4.4.0. This is very important! Failure to follow the proper update steps could cause your panel to become unresponsive.

Now that 4.4.0 has been released you can follow the steps below to update from 4.3.0 to 4.4.0:

1. Swipe down from the top of the panel screen and tap "Settings."
2. In "Settings" tap "Advanced Settings."
3. Enter Installer or Dealer Code (default is 1111 or 2222 respectively.)
4. Tap "Upgrade Software."
5. Tap "Patchtag" then enter iqpanel4.4.0 and then tap "Ok."
6. Tap "Upgrade Using Network," making sure the panel is connected to WIFI. Without a WIFI connection, the upgrade will not go through.

The patch will now be downloaded and then installed. It is important not to touch the panel screen during this process. You'll see a progress bar while the download is in progress, then the panel will reboot. This is normal. Once the panel boots up to the usual security screen, the upgrade is complete. The update usually takes approximately five (5) minutes to complete.

If you prefer, the update can eventually be pushed by your alarm dealer through the Alarm.com dealer portal. If your panel is on an older version, they should also be able to send any prerequisite updates to your panel prior to sending 4.4.0. Just be sure the panel has a connection to WIFI as even updates that are sent through Alarm.com require a WIFI connection at the panel.

Qolsys, which is owned by Johnson Controls, Inc., the same company that owns DSC, is introducing a new lineup of PowerG automation devices. Currently, they offer a door lock along with a range of wired and plug-in switches. These devices will be supported by the IQ4 panels and the IQ Pro.

I say "will be supported" instead of "are supported" because the firmware required to support these new PowerG automation devices hasn't been released yet. For the IQ Panel 4, IQ4 Hub (PowerG Version), and IQ4 NS (PowerG Version) this is firmware version 4.4.0. For the Qolsys IQ Pro, firmware 4.3.0n is required. These firmware updates should be available later this month for the IQ4 Series panels, and soon thereafter for the IQ Pro.

We've talked before about the benefits of PowerG sensors. The big story with this and all PowerG devices is the transmitting range. Depending on the PowerG transceiver being used you can expect hundreds, and up to thousands, of feet in transmitting range. The PowerG repeaters will also work with these devices, so in the unlikely event you need one, a repeater is available.

Compare that to a Z-Wave Plus device, where you can expect a transmitting range of a couple hundred feet at most. Z-Wave is a mesh network, though, so if you plan to install a large number of devices, you can build out an impressive network using that technology. The problem is if you have a single area you want to automate, and it's not near the rest of your Z-Wave network, you might be out of luck with Z-Wave, but not with PowerG!

The encryption used with PowerG security sensors is also used here, so you get 128-bit AES encryption with FHSS (Frequency Hopping Spread Spectrum) which you can read more about here.

IQ Lock-PG:

The IQ Lock-PG (SKU: IQDLK-PGK) is available in three (3) finishes. Shown above from left to right in Satin Nickel, Matte Black, and Oil-rubbed Bronze. This lock is powered by four (4) AA batteries (not included) and with typical use, the battery life expectancy is one (1) year. This estimate is based on six (6) user code unlocking events and ten (10) locking/unlocking events per day. The IQ Lock-PG offers self-handing capability, and the lock motor is noticeably quieter than previous automated locks we've heard.

Unlike some automated locks, the IQ Lock-PG does offer the option to use a key, and two (2) keys are included with it. It has a KW1 keyway cylinder. The IQ Lock logo lights up green when the door is unlocked, and red when it is locked. This provides a nice visual indication of the lock status when the user is returning home or to their business.

Specifications:

• Operating Temperature: Exterior: -31°F to 150°F (-35°C to 66°C), Interior: 32°F to 140°F (0°C to 60°C)
• Material: ANSI Grade 2 Certified
• Compatibility: Compatible with the Qolsys IQ4 NS (No Screen) (PowerG Version), IQ4 Hub (PowerG Version), IQ Panel 4, and IQ Pro panels
• Technology: PowerG
• Key Cylinder: Yes (KW1 keyway)
• Self-Handing: Yes
• Bolt Type: Motorized/ Standard Deadbolt
• User Codes: Up to 250 unique users
• Code Length: 4-10 Digits
• Batteries: Four (4) AA batteries (not included)
• Low Battery Alarm: Yes
• Backset: 2 3/8”/ 2 3/4” Adjustable (60/70mm)
• Door Prep: 1 1/2” / 2 1/8” (38/54mm)
• Door Thickness: 1 3/8” ~ 2 1/4” (35-58mm) automatic adjustment
• Lockout Mode: Keypad lockout for 3 minutes after 10 entries of invalid user code
• Certifications: FCC, IC, ANSI BHMA A156.36 Grade 2, UL10C (20min Fire Rating)
• IP Rating: Exterior assembly: IP54
• Operating Humidity: Exterior: 100% condensing Interior: 20% – 95% non-condensing

IQ Switch-PG:

Next up is the Qolsys IQ Switch-PG (SKU: IQSWH-PG). This is an in-wall on/off switch without dimming. It can replace any standard in-wall switch to add automation capabilities to the circuit. With PowerG technology built-in, you will be able to automate devices in areas you may have thought impossible before. Have an outbuilding that you thought was too far away for automation? With PowerG, that goal may be well within reach depending on how far the building is located from the compatible panel.

Before removing the old switch and replacing it with the IQ Switch-PG, be sure the breaker is turned off. Failure to do so may cause damage to the switch and to you! This is a hardwired switch, which will be connected to 120V, so we do recommend that you have a qualified electrician perform the wiring.

Specifications:

• Technology: PowerG
• Power: 120V at 60Hz
• Maximum Load: Incandescent 600W, CFL/LED 300W
• Current: 5A Max
• Standby Power Consumption: <1W
• Wiring: 16 AWG (direct wire connection)
• Noise: 24dB at 20cm Max
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 140°F (-20°C to 60°C)
• Weight: 4.09 oz (116g)
• Operating Humidity: 0% – 85% non-condensing

IQ Dimmer-PG

The Qolsys IQ Dimmer-PG (SKU: IQDMR-PG) is also an in-wall switch, with dimming capabilities included. As with the IQ Switch-PG, this device can replace any existing 120VAC switch that fits within its specifications to add remote control and automation capabilities.

Another attractive feature for this and all of the new hardwired PowerG switches and sockets is that they come with a screwless faceplate. This provides a clean, modern look. Currently, they are only available in white. If you prefer a more traditional look, the screwless faceplate can be removed and there are screw holes for a traditional faceplate. This may also come in handy if you have multiple switches in a line and require a double-gang or triple-gang setup.

Some Important Specifications:

• Compatibility: Compatible with the Qolsys IQ4 NS (PowerG Version), IQ4 Hub (PowerG Version), IQ Panel 4, and IQ Pro panels
• Technology: PowerG
• Power: 120V at 60Hz
• Maximum Load: Incandescent 200W, CFL/LED 100W
• Current: 1.67A Max
• Standby Power Consumption: <1W
• Wiring: 16-10 AWG (terminal block connection)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 140°F (-20°C to 60°C)
• Weight: 4.83 oz (137g)
• Operating Humidity: 0% – 85% non-condensing

IQ Smart Socket-PG:

The Qolsys IQ Smart Socket-PG (SKU: IQSKT-PG) is an in-wall socket with two (2) sockets that can be controlled individually. By replacing a standard in-wall socket with the IQ Smart Socket-PG you gain the ability to individually control the devices plugged into each outlet from the panel's touchscreen, or from the Alarm.com app or webpage.

Using rules and scenes, you can create automation scenarios to turn devices on or off based on other events that occur on the system, or based on a schedule. With the Smart Rules Builder, available on Alarm.com, you can easily create automation rules to suit your every need.

Specifications:

• Color: White
• Tamper Resistant?: Yes
• Technology: PowerG
• Input Power: 120VAC at 60Hz
• Output Load: 120VAC at 60Hz, 15A Total Max Load for both outlets
• Maximum Load: Total 1800W@120V (Resistive Load)
• Standby Power Consumption: <1W
• Dimensions: 14.5 x 2.75 x 1.7 Inches (115 x 70 x 44 mm)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 131°F (-20°C to 55°C)
• Weight: 5.57 oz (157.8g)
• Operating Humidity: 0% – 90% non-condensing

IQ Smart Plug-PG:

The Qolsys IQ Smart Plug-PG (SKU: IQIDP-PG) is an indoor plug-in module. Often referred to as appliance modules, these devices allow you to quickly turn any existing wall outlet into a smart outlet with no electrician required. With its low-profile form factor, you will be able to make one outlet smart without blocking the other outlet in a traditional two-outlet wall plug.

To learn these devices into any of the IQ4 panel lineup, once you have the 4.4.0 firmware installed you'll press the grey bar at the top of the panel screen, go to Settings > Advanced Settings > Enter Installer or Dealer Code (1111 or 2222 by default) > Installation > Devices > Automation > Auto Learn Devices. From there, just power on the PowerG device and it will auto-learn into the system.

Prior to firmware version 4.4.0, the Automation menu option was missing from the Devices screen, so you won't be able to properly learn these devices on older firmware panels. If you attempt to learn any of them as a security sensor, they will likely learn in, but will not operate properly and will need to be removed from sensor programming prior to proper enrollment once the firmware has been updated.

Specifications:

• Color: White
• Technology: PowerG
• Power: 120VAC at 60Hz
• Output Power: 1800W@120V (Resistive Load)
• Standby Power Consumption: <1W
• Dimensions: 2.6 x 1.5 x 1.29 Inches (68 x 38 x 33 mm)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 122°F (-20°C to 50°C)
• Weight: 2.29 oz (65g)
• Operating Humidity: 10% – 90% RH, non-condensing

IQ Outdoor Plug-PG:

The Qolsys IQ Outdoor Plug-PG (SKU: IQODP-PG) allows you to take one single outdoor outlet plug, and make two (2) smart outlets out of it. These two (2) outlets will be enrolled as separate automation devices and can be controlled individually.

Here's an example of how this plug can come in handy. Perhaps you used to have your patio string lights and a bug zapper connected to the two plugs of an outdoor outlet. You can now connect the IQ Outdoor Plug-PG to one of the existing available outlets, and plug the string lights and the bug zapper into it. You can automate the string lights to come on at dusk and turn off at a set time. Automate the bug zapper to turn on based on some other criteria, whether it's a schedule, or based on the opening of the patio door. And you still have one of your previously existing outlets available for another device.

Specifications:

• Color: Black
• Tamper Resistant?: Yes
• Compatibility: Compatible with the Qolsys IQ4 NS (No Screen), IQ4 Hub, IQ Panel 4, and IQ Pro panels
• Technology: PowerG
• Power: 120VAC at 60Hz
• Output Power: 1800W@120V (Resistive Load)
• Output Load: 120VAC at 60Hz, 15A Total Max Load for both outlets
• Standby Power Consumption: <1W
• Dimensions: 2.6 x 1.5 x 1.29 Inches (68 x 38 x 33 mm)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 122°F (-20°C to 50°C)
• Weight: 2.29 oz (65g)
• Operating Humidity: 10% – 90% RH, non-condensing

At Alarm Grid, we're super excited about the launch of these new automation devices. I believe these will be game-changing, particularly in circumstances where transmitting distance has been a hindrance in the past. I expect we'll see additional PowerG automation devices in the near future.

Hopefully, a PowerG garage door controller, PowerG PGM device, and my personal hope, some PowerG motorized blinds or shades. Stay tuned and we'll let you know when the firmware to support these devices is released. Are you excited about the new PowerG automation products? Leave a comment below and let us know what you think. What other automation devices would you like to see in the PowerG lineup?

In The United States, we have officially celebrated Labor Day as a national holiday since the late 1800s. It is a day to celebrate our country's labor force and to thank our workers for their contributions to the prosperity of our nation. In this spirit, Alarm Grid will be closed on Monday.

From the Alarm Grid family, we'd like to wish everyone a happy, safe, and restful Labor Day. If you will be traveling, don't forget to lock your doors and arm your alarm system. If you have automated lights, set rules or scenes to illuminate the house while you're away to deter potential burglars.

While Alarm Grid technical support, customer service, and shipping employees rest, our customers can rest assured that their systems are continuously monitored by our partners at CMS (USA) and Rapid Response (Canada).

Alarm Grid monitored customers located within the United States receive their monitoring service from Criticom (CMS). When your Alarm Grid-monitored system reports a signal, a CMS operator receives it, and processes it based on a pre-approved set of instructions. Alarm processing may involve sending authorities immediately, or calling the premises and a list of contacts to determine if an emergency exists before a dispatch occurs. Regardless of the exact process, it takes only moments to complete.

If you need to contact CMS, to put your system on test or to report that an alarm was accidentally triggered, you can get in touch by calling (888) 818-7728 and choosing Option 9. When you contact the monitoring station, be sure to have the proper information ready. The operator will need your name, address, and your false alarm password or passphrase. This is very important! If you call either monitoring station during an alarm, and you provide an incorrect password, they will be required to dispatch authorities.

For our monitored customers in Canada, you receive monitoring service through Rapid Response. If you need to contact them to put your system on test or report an accidental alarm you can call (800) 932-3822 and follow the voice prompts. You should only be contacting them for issues such as putting your system on test or canceling a potential dispatch due to an accidental alarm.

Neither of our monitoring partners can provide you with technical support or make changes to your account, so if you need that type of help, please contact us directly. You can email support@alarmgrid.com with details of what you need and we will respond as quickly as possible when we're back in the office on Tuesday, September 5, 2023. At that time we will resume our normal support hours of 9:00 am - 8:00 pm. When we're back in the office, you can contact us by phone at (888) 818-7728.

It is likely that a number of Alarm Grid customers will be affected by Hurricane Idalia, particularly in Florida, Georgia, and South Carolina, based on current modeling. Our monitoring partner, CMS, let us know what steps they were taking to prepare for the storm. We'll lay them out below.

At approximately 5:00 am Wednesday, August 30 Hurricane Idalia became a Category 4 hurricane. According to the Saffir-Simpson Hurricane Wind Scale, a Category 4 rating means winds of 130 - 158 MPH (209 - 251 km/hr). At these speeds, catastrophic damage will likely occur in some areas. Well-built frame structures will likely sustain damage, in some cases extensive damage, to roofs and exterior walls. Trees may snap, or be uprooted, and power poles may also snap. Power outages can be widespread and prolonged.

In response to the expected surge in activity surrounding Hurricane Idalia, CMS has implemented the following measures:

Increased Staffing:

At the Longwood, FL and Manasquan, NJ locations, CMS has increased staffing for the duration of this weather event. In spite of this fact, there is still the possibility that callers to the monitoring station may experience longer than normal hold times.

Partitioning by Location:

Per CMS, "In order to more effectively manage alarm traffic, the CMS Operations team will be transitioning all accounts located in the affected areas to a storm partition. Please understand first responders will no longer respond to dispatches from CMS once sustained winds reach 45 mph." This is a policy of the responding agencies and is outside of CMS or Alarm Grid's control.

Redundancy:

Redundancy is baked into CMS' infrastructure. This is not a special storm-related preparation, but a 24/7/365 way of life. CMS operates three (3) separate monitoring centers in Florida, New Jersey, and California. All are UL-Listed and FM (Factory Mutual) approved. These monitoring centers are connected to one another with the latest in communication technology. This allows CMS to load-balance any increase in activity. It also removes the possibility of a single point of failure taking down operations.

If any of the three (3) centers experience a disaster, each center is backed up by two (2) generators as well as uninterruptable power supplies. Any of the three centers can reroute alarm traffic to the other two centers if the need arises.

Experience:

With over 35 years in business, being founded and headquartered in Florida, and with one of their monitoring centers being located in Florida, CMS operators have seen a lot! They've experienced hurricanes, both personally and in their profession. They are dedicated to keeping their dealers, their customers, and their employees safe.

Our US monitoring station partner, Criticom Monitoring Services (CMS) announced its partnership with Intrado to take advantage of their Text-To-911 (NG911) feature. This allows CMS to send alarm notifications to the authorities via text, rather than requiring a voice call from an operator.

Intrado is a telecommunications company that specializes in public safety communication. They work with PSAPs (Public Safety Answering Points) to improve the delivery of calls for service. A PSAP is where 911 calls are usually routed. It can be a separate entity, or located within a particular jurisdiction's telecommunications center. Many years ago when I was a dispatcher, 911 calls in the Louisville area were received by the PSAP office and then routed to the various police, fire, or EMS dispatch centers. If the PSAP was overrun, their calls rolled over to our call center.

Traditionally, when an alarm signal is received by the monitoring station, the signal goes to a special receiver. From there, an automation software package turns that signal into plain text that the operator then uses to process the signal. This may include calling the end-user to verify if authorities are needed before dispatch, or dispatching immediately.

Up until now, when the central station operator needed to dispatch, they manually called the authorities and relayed the appropriate information. This process only takes a few minutes, usually, but when you're waiting for the authorities in an emergency situation, minutes can feel like hours.

With this new integration, information on alarms that require dispatch is sent to participating PSAPs via text. And this is not a dump-and-run situation like the old voice dialers of yore. The text conversation is two-way. The PSAP can request additional information, and the central station operator can continue to provide information until the PSAP closes the chat. This allows the information on this particular incident to get into the hands of those who are in the best position to help much more quickly and accurately than ever before.

Even with all the improvements in alarm technology in recent decades, there are still times, such as during heavy storms, when a lot of alarms go off at roughly the same time. This can overwhelm both the monitoring station and the authorities who respond to alarms. I can foresee this technology making a huge impact on the efficiency with which alarm signals are handled moving forward, and I hope that every PSAP will adopt this new technology.

CMS began implementing this partnership with Intrado in December of 2022 with three (3) agencies in Florida. As of August 2023, they have over 130 agencies on board, and as more PSAPs sign up with Intrado, they will be folded into the integration with CMS. The current list of participating agencies can be found here.

This is just another way that the alarm industry is working to improve its service to both the alarm user and the community at large. What do you think about this new partnership? Leave a comment below and let us know your thoughts. We look forward to hearing from you!

Exciting news! Alarm.com has unveiled a new customer app with a fresh look. Faster response times and fewer clicks mean instant access to the data you need. Video and Activity are now conveniently available right from the Dashboard, ensuring quick access to your most vital information.

In addition to the changes and time savings you can see, response times have been improved at the server level as well. Now, instead of clicking the hamburger menu (≡) and then selecting an option, the most commonly used selections, like Video, Activity, and Home, are pinned right at the bottom of the screen.

When you first log in to the app after the update, you'll see a What's New screen that summarizes all the updates.

The Dashboard can be customized so that when you log in, you see exactly what you want, and nothing that you don't. In the example below, Images and Highlights have been removed from the Dashboard. Click and drag the enabled cards to rearrange the order in which they are displayed. To edit the dashboard, click the Home icon, and scroll to the bottom of the screen, then tap Edit Dashboard.

Tapping the Video icon brings you to the video screen where you can see a live view of any camera in your account. You can also see Saved clips, and if you have any cameras enrolled in Onboard Recording you can click the 24/7 option to review selected feeds.

Clicking the gear icon allows you to edit various video settings.

The Activity screen shows you a list of events in chronological order with the newest events at the top. Each day has a Highlights section that provides a brief animated recap of the day's events. Video events provide a thumbnail for quick access to review those items. Use the extensive filter options to find specific items quickly.

Clicking the More option provides you with the options you used to see when clicking the hamburger menu in the upper left.

This upgrade appears to be a significant step forward for Alarm.com. By streamlining the user experience and placing the most pertinent information front and center within the app, overall usability and efficiency are enhanced. As users, we can all appreciate any change that simplifies navigation and reduces the number of clicks needed to access desired features! I am personally excited about this update and how it will make managing our alarms and security systems even more convenient. What are your thoughts on the latest Alarm.com UX update? Feel free to share your opinions and experiences in the comments below. We look forward to hearing from you!

Total Connect 2.0 now offers a server-to-server integration with Genie® and Overhead Door™ garage door openers. This allows you to control your alarm system, automation devices, and garage doors from a single app. No more fumbling between apps to control both your alarm system and garage door.

The new Genie® and Overhead Door™ server-to-server integrations join Chamberlain and LiftMaster as well as several others. Between these server-to-server options and the Z-Wave options for garage door control, you can now operate nearly any garage door from the TC2 app. This makes it much more convenient when attempting to control multiple systems at once, such as when you are arming your system to leave, or disarming your system to return home, and you also need to control the garage door.

This integration doesn't allow for the automation of the garage door, sadly. It provides manual control only, but it is still a worthwhile integration because it simplifies the process of leaving and returning, which most of us do each day, multiple times per day. To set up the integration you simply need a compatible Genie® or Overhead Door™ product, a WIFI connection for that product, and a Total Connect 2.0 account with the Smart Home plan. For Alarm Grid customers, that is a Silver Plan (Self or Full) or higher.

Step-by-Step FAQ for Overhead Door® Integration
Step-by-Step FAQ for Genie Aladdin Connect® Integration

Setting up the integration is easy. Once you log into your Total Connect 2.0 account, click on Devices. Click the three (3) vertical dots in the upper right corner then tap Add/Remove Devices:

From there, choose Genie or Overhead Door™ from the list of available integrations. You will have two (2) options. You can either "Link to Existing Account" or "Add New Account". If you've already been using the garage door opener manufacturer's app, choose the former, if not, choose the latter.

If you choose "Link to Existing Account," you'll be prompted to enter your login credentials for the existing Genie (Aladdin Connect®) or Overhead Door™ (OHD Anywhere®) app, and then click "Login." Once the credentials are verified, you'll see a list of garage doors to select which ones you want to enable.

On the other hand, if you choose "Add New Account," you'll be redirected to the app store to download either Aladdin Connect® or OHD Anywhere®. Follow the provided instructions to set up your garage doors for remote access. Once completed, return to TC2 and follow the steps to complete enrollment. Once again, you'll need to enter the credentials you created for the garage door manufacturer's app and click "Login." Select the garage doors you want to enroll, and you're all set!

We're thrilled to see Resideo adding new third-party integrations to its Total Connect 2.0 offering. While Alarm.com has been more proactive in supporting this type of integration in the past, Resideo is starting to close the gap. We can't wait to see what they offer next!

When the ADC-VDB770 was first released, one of its newest features was a battery with a warmer. This allows the doorbell to work in colder climates without issues. However, users in hot climates have experienced some issues. So, the doorbell will now ship with a battery-less insert instead.

Installations that use a digital chime require a battery, and will not be able to use the battery-free insert. For those customers ordering a new ADC-VDB770 in July 2023 or later, who will be using the doorbell with a digital chime, you must also purchase the ADC-VDBA-770BAT. This is the battery replacement kit for existing ADC-VDB770 units whose battery has reached its end of life, and for new users who will use a digital chime.

If you will be using a mechanical chime, or the wireless chime available from Alarm.com, then you can install the ADC-VDB770 with the included battery-free insert. It charges quickly, which makes for a quick and easy installation. Users in colder climates may also need to purchase the ADC-VDBA-770BAT to prevent issues associated with extremely cold weather.

The purpose of the battery in the ADC-VDB770 is to power the video doorbell for the short period of time that the button is pressed. During a button press, the power circuit of the video doorbell is shorted, which is what causes the doorbell to chime. If not for the battery (or battery-free insert) the doorbell would lose all power during the button press. For a traditional doorbell, this is not a problem. But for a video doorbell, it is.

The battery-free insert, which will now be shipped with the ADC-VDB770 rather than the battery and warmer, is a capacitor that stores a charge. It provides enough power to keep the video doorbell powered while the button is pressed. However, digital chimes require that the button be pressed for a longer period of time, which is why for those chime types the battery is required.

Customers who had overheating issues with the ADC-VDB770 as it was originally sold, with a battery and heater, usually had the doorbell mounted in a location where it got lots of direct sunlight. The battery-free insert is currently not available for individual sale, but this may change in the future. If it does, we'll let you know. For now, if you have an original Alarm.com ADC-VDB770 and the battery is at its end-of-life you will need to replace it with the ADC-VDBA-770BAT.

The Alarm.com App can now be used directly from a car's touchscreen display via Android Auto™. Most cars made in 2018 or later can support the Android Auto™ feature. For some cars, a wired USB connection may be required, while others can take advantage of the feature wirelessly via Bluetooth.

Both Android Auto™ and Apple Carplay™ are meant to help you use your phone more safely while driving. By moving certain controls from the phone to the vehicle's touchscreen, you can take care of necessary phone interactions without having to actually look at the phone. In many cases, voice commands can be used, rather than having to look at and touch the screen. This promotes safety by reducing distracted driving.

Alarm.com can now take advantage of this safety-enhancing feature and work with Android Auto™. At this time, the Alarm.com App does not interface directly with Apple Carplay™ We currently have no word on when, or even if, it ever will. Whether your vehicle requires a USB connection or can interface via Bluetooth will vary per vehicle year and model.

It's simple to get started with this integration. All you need is a commercial or residential Alarm.com account, a compatible Android phone, and either a vehicle or an after-market stereo system that supports Android Auto™. Just login to the Alarm.com app, and connect the Android phone using Android Auto™. If this is your first time connecting to Android Auto™ you may need to check the phone's display for a permission message.

From there, you will be able to run the Home and Away scenes from the car's touchscreen. You can also see the status of your garage doors, open or close them, and receive important system notifications. These notifications may include pending alarms, alarms, arming reminders, and geo-fence-related events.

There are three (3) types of notifications you may receive when using Alarm.com with Android Auto™. They are Alarm.com notifications, Head Unit notifications, and Notification Center notifications:

Alarm.com Notifications:

This type of notification will include pending alarms, alarms, arming reminders, and location-based notifications such as garage door left open, sensor left open, and panel left disarmed among others.

Head Unit Notifications:

Head Unit notifications will appear on the touchscreen, even if the user is not logged into the Alarm.com Android Auto™ interface. This notification will likely appear as a banner at the top of the display. It will show the notification, along with an action and a dismissal icon.

For example, the notification may show that the garage door has been left open with an icon allowing you to close it, or an X to dismiss the notification. Head Unit Notifications will only provide the primary action as an option for dealing with the notifications. If you view the same notification in the Notification Center, there could be a primary and a secondary action option.

Notification Center Notifications:

Notification Center notifications provide slightly more information. In this screen, you may see up to two (2) different action options with text to explain what each available action is. For example, if the notification is that the system was left disarmed, you may have the option to arm it either Away or Stay. Whereas, on the same Head Unit notification, you will only be given the option to arm Stay (the primary action).

To get to the Notification Center, click the notification icon on the lower right side of the car's touchscreen. Use the arrows, or flick to scroll through the available notifications. Some notifications will not have any type of action associated with them. Others may have one (1) or two (2) different options to choose from.

The table below shows the different types of notifications and the primary action associated with that notification if there is one. Only the arming reminder notification offers a secondary action:

Alarm.com constantly strives to find new ways to improve its product. This latest integration aims to keep you safe both at home and on the road. We're standing by to see what new feature they come up with next. I'm sure we won't have to wait long!

The 4th of July, aka, Independence Day is the ultimate summer event. It is a celebration of our country's independence from Britain. On this day, most of us will engage in cookouts, swimming, eating, drinking, and fireworks, or some combination of those things. Just remember to do it safely!

Our hardworking support staff will be off, and our offices will be closed for the holiday. Of course, our central station partners Cricitom (CMS) and Rapid Response will be on the job, monitoring Alarm Grid customer systems. When it comes to alarm response, nothing will change.

If you need to contact the central monitoring station, to cancel a false alarm or verify a signal, customers in the US can contact Criticom (CMS) by dialing (888) 818-7728 and choosing Option [9]. This will get you in touch with an operator who can assist you with canceling a false alarm, putting your system on test, or checking an alarm signal. You can also set up a MyAlarms.com account, so that you can do those things yourself online without having to call.

Canadian customers can contact Rapid Response at (800) 932-3822. Remember when you call either monitoring station, you will be asked for your name, address, and your false alarm password or phrase. Providing incorrect information when asked, will result in the dispatch of authorities.

If you have a support question or if you need to make adjustments to your account, the monitoring station cannot assist you. In that case, send an email to support@alarmgrid.com with details of your request and we will begin to address these support issues as soon as we return to the office on Wednesday, July 5. At that time, we will return to our normal business hours of 9:00 am - 8:00 pm Eastern, Monday - Friday.

We hope you enjoy the holiday. We recommend that you wear sunscreen, and drink plenty of water if you'll be spending time outdoors in the heat, even if you're swimming. Be careful if you'll be handling fireworks and let's all meet back here on Wednesday to share stories about our holiday!