Product Announcements Posts

Alarm Grid and Alarm.com customers in Ameren, IL can sign up for the Peak Time Savings Program. Once enrolled, you will receive a $50 e-gift card. For each subsequent year you remain enrolled, you will receive a $25 e-gift card. This is another way your smart thermostat can pay for itself.

We've written about the Give Back, Get Back program numerous times in the past. Many different utility companies offer a similar incentive program, and each company has its name for the program. Some offer rebates, others may offer bill credits. The incentive amounts also vary. The information included here is specific to the Ameren, IL program.

To qualify for this incentive, you just need the following:

• Be a residential electric customer in Ameren, IL, with service in your name.
• Use an internet-connected, qualifying smart thermostat.
• Sign up for the program, which allows the Ameren, IL electric company to make small adjustments to your thermostat remotely, during peak usage times.
• You must not already be participating in a demand response program.

The times when your thermostat is likely to be adjusted are during the hottest days of summer when power demands are at their greatest. This can cause strain on the electrical grid. By signing up for the Peak Time Savings Program, you agree that the electric company can make small adjustments of four (4) degrees or less during these times. These adjustments will last for no more than four (4) hours.

The most likely hours during which an adjustment may occur are between 1:00 p.m. and 7:00 p.m. CT, but adjustments could occur anywhere from 6:00 a.m. to 10:00 p.m. CT. You retain control of your thermostat and can opt out of an adjustment event at any time. In some cases, the thermostat may briefly be adjusted down (cooler) before being adjusted up (conservation) to maintain comfort during the adjustment period.

The thermostats that are compatible through Alarm.com are:

• Trane ComfortLink Control
• RCS Z-Wave Communicating Thermostat
• GoControl Z-wave Thermostat
• Alarm.com Smart Thermostat
• 2GIG Z-Wave Plus™ Battery Powered Thermostat
• Trane Z-Wave Thermostat
• Linear Thermostat
• Smart Thermostat HD (ADC T40K-HD)
• ADC T3000
• ADC T2000

You can sign up for the program by going to this page, and then clicking the link "Enroll Your Smart Thermostat." Once you are accepted, you should receive an email within 60 days of being accepted. The $50 e-gift card will be delivered to your email, so be sure when you sign up, you enter the correct email information.

If you remain enrolled in the program, on the anniversary of your enrollment, you will receive a $25 e-gift card via email for your continued participation. This will occur each subsequent year you remain enrolled. Currently, there is no end date, so this incentive will continue until you are notified otherwise.

It's the middle of winter, but summer will be here before you know it. If you've been on the fence about purchasing a smart thermostat, this may be the perfect time to commit. Signing up for a program like this may seem like a small step, but as they say, the journey of a thousand miles begins with the first step and every step brings you closer to your goal. In this case, the goal is energy conservation, and every little step helps.

Alarm.com recently announced that due to some network changes undertaken by T-Mobile, those customers who currently receive MMS (Multi-Media Messaging Service) notifications with video clips and thumbnails, will soon begin receiving SMS (Short Message Service) messages with links instead.

This only affects Alarm.com customers who use T-Mobile for their mobile phone service. Currently, the change is set to go into effect on January 31, 2024. Those customers who use both Alarm.com and T-Mobile who are on iOS devices with the latest software may not notice a change, as those devices will automatically open the links to offer a preview. However, for customers on Android devices, or iOS devices that are not updated this change will likely be readily apparent.

Alarm.com supports Push Notifications through the Alarm.com app, and they encourage the enabling of Push Notifications for all Alarm.com customers who use smart devices to receive notifications. They are taking steps to minimize the use of MMS messaging regardless of carrier. Those steps are as follows:

• T-Mobile Customers: As already mentioned, with the changes at T-Mobile, those customers will begin receiving SMS, instead of MMS, messages at the end of January. In these messages, they will receive links to thumbnails and clips, rather than the clip or thumbnail being embedded in the message. Users on updated iOS devices may not notice this change as these devices will open the links automatically. For users with other devices, such as Android phones, the change will be more noticeable.
• UI Updates. Over the next several months, Alarm.com plans to roll out expanded messaging options within their user interfaces to make Push Notifications the more attractive option for customers. They plan to release new tools that will make the use of Push Notifications even easier to set up and use.

As we mentioned before, Alarm.com strongly recommends that customers use Push Notifications instead of SMS or MMS messaging. There are several advantages to this, including:

1. In Push Notifications, users are redirected to live or saved clips, depending on whether the clip has been uploaded yet. This allows them to access their content quickly.
2. Users can pause notifications directly from Push Notifications.
3. Push Notifications offer unique doorbell sound effects.
4. As iOS and Android devices continue to evolve, Alarm.com will continue to enhance the features of Push Notifications.

Alarm.com customers who use T-Mobile phone service need not do anything. These changes will take effect automatically at the end of January, 2024. You can read about the different types of customer notifications here. For help setting up Push Notifications, you can read this article.

If you're both an Alarm.com and a T-Mobile customer, we'd love to hear your thoughts on these changes. Give us your opinion on the new format. Do you use Push Notifications, with SMS or MMS as a backup? Does this change your feelings about either Alarm.com or T-Mobile? Start a conversation in the comments below.

It's that time of year again! The time when you might spot Santa Claus on your Alarm.com video feed as he prepares to deliver Christmas gifts. Of course, the true magic occurs on Christmas Eve, but Santa could drop by at any time between December 4 and December 31. So, be on the lookout!

Alarm.com is always enhancing and expanding its video offerings. For the past few years, its technology has become so advanced that it can capture Santa Clause as he goes about his pre and post-holiday preparation.

Any time between December 4 and December 31, 2023, you may catch a glimpse of the jolly old elf as he scurries about, scoping out the surroundings and getting all of the logistics prepared for the big night. Delivering toys to all the children of the world in a single night requires meticulous preparation!

The only way you can see Santa is if you capture a still image from your video feed. Santa is much too quick to be seen on the video feed itself. Just log into your Alarm.com account, pull up the feed of one of your Alarm.com cameras, and click the Santa icon. You'll see the various Santa poses captured within the feed. Click the one you like best, and then share the image with your family and friends.

In dark settings, Santa will appear in black and white, in lighted areas you'll see him in color. Just be sure you have the latest version of the Alarm.com app installed on your iOS or Android device so that you can take advantage of this rare opportunity. For iOS users, the latest version is 5.2.1. For Android users, the version you see will vary depending on your device. Just check the Google Play store and be sure there are no available updates. Your phone must be on Android 7.0 or higher to support the Alarm.com app.

Of course, only those with a video subscription, and cameras installed will be able to capture Santa Clause in action. For Alarm Grid customers, this will be those on one of our Platinum Plans (Self or Full) or a Video Monitoring Account. If you've been considering adding an Alarm.com video camera to your system now may be the perfect time!

If you don't happen to have Alarm.com video service, but you do use Alarm.com monitoring for your security system, you have another option for tracking Santa as he visits your home. You can set up a Santa Alert for your system. To do so, follow these steps:

1. Designate a sensor. Log into your Alarm.com security account. Tap the Sensors card and choose a sensor that is easy for you to open and close. Change the name of that sensor to something fun. If you have a chimney, you can call it Chimney Sensor. If not, you can name it Santa Sensor, or a similar fun name.


2. Create a notification. If you don't already have a zone open/close notification set up for the sensor you chose, tap the Notifications menu option, then click the "+ New Notification" icon. Looking at the Standard Notification options, you should see "Sensor Activity." Click on this option.
   
   
   
   
3. Complete the notification setup. When you click on the "Sensor Activity" option, you'll be taken to a configuration screen. First, name your notification. Check the box next to the sensor you renamed in Step 1. Configure all the required parameters to ensure you receive a notification when this sensor is opened. Remember, a notification will be sent every time this sensor is opened or faulted, so you probably want to wait until you're ready for Santa to visit, before you set this up. Otherwise, if this is a sensor you use often, you may be inundated with notifications until you set things back to normal. Presumably, you'll do this on Christmas Eve. Be sure you have at least one recipient for this notification enabled. When you've completed the configuration, click "Save."
   
   
   
4. Create the event. When it's time for Santa's visit, open the sensor you renamed in Step 1. You should receive a notification on your designated device that shows the Chimney Sensor, Santa Sensor, or whatever fun name you gave your sensor has been opened. In the morning, you can show your family proof that Santa Claus visited during the night.


5. Revert to normal. Once you have your proof, you can reverse the above steps and put your system back to normal. There is no need to delete the notification. You can simply toggle it off, then it will be ready again next year, in case you want to use it again.

The First Alert VX3 HD (CAMWE-WO) is the newest camera offering from Resideo and Honeywell Home using the First Alert brand name. It offers full HD viewing and recording and supports Wide Dynamic Range (WDR). Its built-in speaker and microphone support 2-way audio through the TC2 app.

Resideo completed the purchase of First Alert in 2022 and is now beginning to roll out products using the First Alert name. So far, we've seen the First Alert VX1 HD (CAMW-WDB) HD doorbell camera, and now the VX3 HD. First Alert brings with it end-user brand recognition, as well as manufacturing capabilities for life safety and other devices.

The newly introduced VX3 HD boasts a sleek, modern design and a compact form factor. A notable advancement in this camera, compared to earlier TC2-compatible models, is its intelligent event detection capability. This sophisticated AI-driven feature distinguishes between people, vehicles, animals, and packages effectively reducing unnecessary alerts. This functionality is present in both the VX3 HD camera and its counterpart, the VX1 HD video doorbell.

Another exciting feature of this new outdoor camera is the ability to use Power over Ethernet (PoE). Because the VX3 HD also supports WIFI, it can be powered by a 12VDC, 1A power supply. But, if you plan to use an ethernet connection for networking, you may as well take advantage of its PoE capabilities. The VX3 HD is an 802.3 af PoE class 3 PD. The maximum cable length when using PoE is 300' (100m).

The First Alert VX3 HD offers many impressive specifications. You can read the full spec sheet here. One thing we haven't discussed yet is Wide Dynamic Range (WDR). You may be wondering what the difference between High Dynamic Range (HDR) and Wide Dynamic Range (WDR) is.

Both HDR and WDR have to do with the contrast and resolution in images that have both very dark and very light areas. HDR uses processing power and software to take these images and perfect them, as much as possible, so that the viewer can get the most detail possible from the image. With HDR, it's all software-based.

WDR uses both hardware and software to achieve the same goal. One example of how this occurs is that shutter speed is controlled by the camera, so that in areas where there is an abundance of light, shutter speed is faster, allowing less light into the camera, and in darker areas, shutter speed is slower, to take in more light. In many cases, multiple images are taken with different exposure levels and then combined to provide you with the best possible image.

A custom back box is available for installations where in-wall wiring is not possible, or for anyone who needs additional space to protect cables. The CAMWE-WOBB replaces the standard mounting bracket and is installed behind or beneath the camera. It can support up to three (3) 1/2" (1.27cm) conduits. It has rubber grommets that can be used to protect any conduit space that is not being used. With an IP66 rating, the back box is dust-proof and water-resistant.

Alarm Grid customers who want to take advantage of all the advanced features of the VX3 HD will need to sign up for either a Platinum Plan (Self or Full) or a Stand-alone Video Plan. This camera is compatible with Total Connect 2.0, and can also be viewed through the Honeywell Home PROA7PLUS or Resideo PROA7PLUSC touchscreen. As long as the panel is on version 03 or higher. It can also be viewed on the PROWLTOUCH or PROWLTOUCHC secondary keypad when used with one of these panels.

Up to eight (8) cameras can be added to each monitoring plan that supports cameras, and each First Alert VX3 HD counts as one (1) camera. Full access to the camera, including the 2-way audio feature, is accessible through the TC2 app. The website does not support 2-way audio, and will only allow you to view the camera's live feed and captured video.

The 2-way audio feature allows the user to listen in to ambient sound in the vicinity of the camera, and to speak through the camera to anyone within view. This feature can be used to deter potential burglaries, scare away stray animals, or play tricks on your friends. There is also an LED spotlight and siren feature that can be deployed manually by the end-user to deter intruders in the vicinity of the camera.

Some Resideo 5821 wireless flood and temperature sensors manufactured between July and October of 2023 may not transmit properly. They may fail to learn into the alarm panel or fail to transmit when an alarm occurs. Affected units can be returned to the vendor for refund or replacement.

The 5821 is a versatile wireless sensor from the Resideo (formerly Honeywell) 5800 Series sensor line. Alone, it can monitor for high and low temperature conditions. It can also be used with either a remote temperature probe, or a remote flood-sensing probe. The use of either remote probe allows the 5821 to monitor harsh conditions that the circuitry of the transmitter itself cannot endure.

The date code for the 5821 is located on the box it comes in, and should also be visible as a sticker or a printed series of numbers on the circuit board itself. The date code consists of a 2-digit number for the year and a 2-digit number for the week of that year.

In 2023, between week 30 and week 40*, a manufacturing issue caused 5821 transmitters to be produced with a defect that caused affected units not to transmit properly. These units may never learn into the panel, or they may fail to transmit when a monitored condition occurs. This could result in damage to a home or business.

The date codes included in this notice are 2330 (2023, week 30) through 2340 (2023 week 40). Any unit with date code 2342 or later is not affected by this issue. July 24, 2023 begins week 30, and October 8, 2023 ends week 40.

If you recently purchased a 5821 from Alarm Grid, check the date code on the unit. If it falls within the affected range, contact us at support@alarmgrid.com and we will happily provide you with a warranty replacement. You can read the full notification from Resideo here. If you received a unit that would not learn into the panel initially, it is likely that we have already performed troubleshooting with you and have at least begun the warranty replacement process.

For customers who may not read our blog, Alarm Grid is reaching out to anyone who purchased this product from us from March 2023 until now. We will provide information on the notification, how to check the date code, and will gladly replace any units affected.

*Important Note: When this issue was discovered, production of the 5821 was halted and the issue was investigated to discover the root cause. There was no production of the 5821 during 2023 week 41, which accounts for the seemingly "lost week" missing in the above referenced announcement.

Update 09/18/23: Qolsys has released this firmware as of today. Alarm.com, however, has not yet made it available for dealers to perform remote OTA updates. They usually lag behind Qolsys by a few days, as they perform their own testing. Instructions for updating using a patch tag can be found here. The full Qolsys TSB can be found here.

Original Blog Post:

We've been hearing about it for a while, and Firmware 4.4.0 will be available any day now. In this post, we'll go through some of the big additions, fixes, and improvements that you can expect to see in this release. From support for PowerG automation devices to the addition of Night arming.

This is one of the most ambitious updates for Qolsys that we've seen. There are a lot of new features in this update. There are also some important fixes and improvements included. In this post, we'll go through what we believe are some of the more important changes coming up in Firmware 4.4.0.

New Features:

• Support for All New PowerG Automation Devices:
  • IQ Lock-PG
  • IQ Dimmer-PG
  • IQ Switch-PG
  • IQ Smart Socket-PG
  • IQ Smart Plug-PG
  • IQ Outdoor Plug-PG
• Added a new Automation Icon within the Installation > Devices Menu. This icon is where you will now go to add everything except Z-Wave Automation devices. However, from within this screen, you can reach Z-Wave Automation (if you navigate here in error). In the future, we expect all Automation will be programmed from within this screen.
• Added "Night Arming" mode. The panel can now be armed in "Away", "Stay", or "Night".
• Created a new PIN code setting for users of the IQ WIFI 6. This will restrict access to the profiles and network map settings of the router.
• Added support for Aeotec Indoor Siren 6.
• Added Sensor Group 11 (Day Zone) and Group 21 (Night Motion).
• Added Sensor Groups 61 (Fixed Intrusion Panic) & 62 (Fixed Silent Panic). With these settings, hardwired, latching panics can now send restore signals when they are physically restored.
• Allows exterior PowerG motions to be programmed as Door/Window sensors to expand the Sensor Group options when programming.
• Added the option to display ambient temperature on the IQ Panel 4 and IQ4 Hub screen when used with PowerG and PowerG Plus devices that support reporting ambient temperature (listed below).
  
  
  • PG9312
  • PG9309
  • PG9200AX
  • PG9350SL
  • PG9914
  • PG9862
  • PG9872
  • PG9984P
  • PG9922
  • PG9936
  • PG9933
  • PG9905
  • PGP9945E
  • PGP9922
  • PGP9920
• PowerG Smoke Detectors can now sound different cadences for Intrusion, Fire, and CO alarms when the "PowerG Smoke Detector Siren" option is used for additional sounders.

Before going on to Fixes and Improvements, I wanted to pause for a moment and expand a bit on a couple of the things listed above. With the new Sensor Group 11 (Day Zone) here is the description of operation for that zone type: Intended for a Door or Window zone that triggers an alarm instantly if the system is armed (same as Group 13). When the panel is disarmed, the zone will annunciate Opens AND Closes, and will continue to notify until the Dismiss button is pressed on the panel screen.

When it comes to Night Arming, an understanding of the Groups associated with motion detectors is essential. Below is an explanation of how each Sensor Group operates. All of these Groups are supervised.

• Group 17, Away-Instant Motion: Active only when armed to "Night" or "Away". Trips instantly when motion is detected. Does not trip if an E/E zone is tripped first.
• Group 15, Stay-Instant Motion: Active in "Stay," "Night," and "Away". Trips Instantly when motion is detected. Does not trip if an E/E zone is tripped first.
• Group 35, Stay-Delay Motion: Active in "Stay," "Night," and "Away" modes. Triggers an Entry Delay if motion is faulted. Does not trip if an E/E zone is tripped first.
• Group 20, Away-Delay Motion: Active when armed to "Night" and "Away". Triggers an Entry Delay if triggered first. Does not trip if an E/E zone is triggered first.
• Group 21, Night Motion (New): Active only when armed to "Away" and trips instantly when motion is detected by this sensor first. Does not trip if an E/E zone is tripped first.
• Group 25, Safety Motion: This sensor does not report or trigger an alarm. This is a "Chime-Only" sensor when "Activity Monitoring" is active, regardless of panel armed status. Used for medicine cabinets, storage, activity tracking, etc.

Panel Fixes and Improvements:

• Changed the Z-Wave naming convention for Settings related to Automation.
• Added support for Z-Wave Weiser/Kwikset Lock supervision requests.
• Made improvements to text size and movement in Photo Frame Screensaver.
• Enhanced the downloading of images and videos from the IQ Panel to a mobile device.
• Added a 30-second arming delay for the IQ Panel 4's built-in glass break detector.
• Fixed an issue with pairing the ADC S2000-T Temp Sensor to the panel.

IQ Remote PowerG Fixes and Improvements:

• Added the ability for the IQ Remote PowerG to automatically power back on after an extended power failure/battery drain, once primary power is restored.
• Corrected an issue where "Nighttime Mode" was not working properly on the IQ Remote PowerG.
• Changed the functionality of the Power Button on the IQ Remote PowerG. Power Down/Reboot now requires a 10-second button press.
• Added support for Thermostats and Garage Door Control to the IQ Remote PowerG.
• Added "Weather Clock" to the IQ Remote PowerG Frame Options.
• Weather to the IQ Remote PowerG now functions when paired in both PowerG and WIFI modes.
• Added support to IQ Remote PowerG for "Installer Test Mode" where the siren is temporarily silenced during testing.
• Added support to the IQ Remote PowerG for Doorbell Notification pop-up and chime, when paired over both PowerG and WIFI.
• IQ Remote PowerG enrolled over PowerG will now automatically upgrade upon first enrollment, rather than waiting 24 hours.
• General communication improvements (Sync/Delay).

Update Instructions:

This firmware is now available, so you can perform the update. Your panel must be on Firmware Version 4.3.0+ before upgrading to 4.4.0. To check your firmware version, tap the gray bar at the top of the panel's home screen, then press Settings > Advanced Settings > Enter Installer or Dealer Code (1111 or 2222 respectively) then tap About > Software.

If your panel is on Firmware Version 4.0.0, 4.0.1, or 4.1.0, you must first update to 4.1.1.

From there, you can update to 4.2.0 or 4.2.1. Then you can update to 4.3.0 and finally to 4.4.0. This is very important! Failure to follow the proper update steps could cause your panel to become unresponsive.

Now that 4.4.0 has been released you can follow the steps below to update from 4.3.0 to 4.4.0:

1. Swipe down from the top of the panel screen and tap "Settings."
2. In "Settings" tap "Advanced Settings."
3. Enter Installer or Dealer Code (default is 1111 or 2222 respectively.)
4. Tap "Upgrade Software."
5. Tap "Patchtag" then enter iqpanel4.4.0 and then tap "Ok."
6. Tap "Upgrade Using Network," making sure the panel is connected to WIFI. Without a WIFI connection, the upgrade will not go through.

The patch will now be downloaded and then installed. It is important not to touch the panel screen during this process. You'll see a progress bar while the download is in progress, then the panel will reboot. This is normal. Once the panel boots up to the usual security screen, the upgrade is complete. The update usually takes approximately five (5) minutes to complete.

If you prefer, the update can eventually be pushed by your alarm dealer through the Alarm.com dealer portal. If your panel is on an older version, they should also be able to send any prerequisite updates to your panel prior to sending 4.4.0. Just be sure the panel has a connection to WIFI as even updates that are sent through Alarm.com require a WIFI connection at the panel.

Qolsys, which is owned by Johnson Controls, Inc., the same company that owns DSC, is introducing a new lineup of PowerG automation devices. Currently, they offer a door lock along with a range of wired and plug-in switches. These devices will be supported by the IQ4 panels and the IQ Pro.

I say "will be supported" instead of "are supported" because the firmware required to support these new PowerG automation devices hasn't been released yet. For the IQ Panel 4, IQ4 Hub (PowerG Version), and IQ4 NS (PowerG Version) this is firmware version 4.4.0. For the Qolsys IQ Pro, firmware 4.3.0n is required. These firmware updates should be available later this month for the IQ4 Series panels, and soon thereafter for the IQ Pro.

We've talked before about the benefits of PowerG sensors. The big story with this and all PowerG devices is the transmitting range. Depending on the PowerG transceiver being used you can expect hundreds, and up to thousands, of feet in transmitting range. The PowerG repeaters will also work with these devices, so in the unlikely event you need one, a repeater is available.

Compare that to a Z-Wave Plus device, where you can expect a transmitting range of a couple hundred feet at most. Z-Wave is a mesh network, though, so if you plan to install a large number of devices, you can build out an impressive network using that technology. The problem is if you have a single area you want to automate, and it's not near the rest of your Z-Wave network, you might be out of luck with Z-Wave, but not with PowerG!

The encryption used with PowerG security sensors is also used here, so you get 128-bit AES encryption with FHSS (Frequency Hopping Spread Spectrum) which you can read more about here.

IQ Lock-PG:

The IQ Lock-PG (SKU: IQDLK-PGK) is available in three (3) finishes. Shown above from left to right in Satin Nickel, Matte Black, and Oil-rubbed Bronze. This lock is powered by four (4) AA batteries (not included) and with typical use, the battery life expectancy is one (1) year. This estimate is based on six (6) user code unlocking events and ten (10) locking/unlocking events per day. The IQ Lock-PG offers self-handing capability, and the lock motor is noticeably quieter than previous automated locks we've heard.

Unlike some automated locks, the IQ Lock-PG does offer the option to use a key, and two (2) keys are included with it. It has a KW1 keyway cylinder. The IQ Lock logo lights up green when the door is unlocked, and red when it is locked. This provides a nice visual indication of the lock status when the user is returning home or to their business.

Specifications:

• Operating Temperature: Exterior: -31°F to 150°F (-35°C to 66°C), Interior: 32°F to 140°F (0°C to 60°C)
• Material: ANSI Grade 2 Certified
• Compatibility: Compatible with the Qolsys IQ4 NS (No Screen) (PowerG Version), IQ4 Hub (PowerG Version), IQ Panel 4, and IQ Pro panels
• Technology: PowerG
• Key Cylinder: Yes (KW1 keyway)
• Self-Handing: Yes
• Bolt Type: Motorized/ Standard Deadbolt
• User Codes: Up to 250 unique users
• Code Length: 4-10 Digits
• Batteries: Four (4) AA batteries (not included)
• Low Battery Alarm: Yes
• Backset: 2 3/8”/ 2 3/4” Adjustable (60/70mm)
• Door Prep: 1 1/2” / 2 1/8” (38/54mm)
• Door Thickness: 1 3/8” ~ 2 1/4” (35-58mm) automatic adjustment
• Lockout Mode: Keypad lockout for 3 minutes after 10 entries of invalid user code
• Certifications: FCC, IC, ANSI BHMA A156.36 Grade 2, UL10C (20min Fire Rating)
• IP Rating: Exterior assembly: IP54
• Operating Humidity: Exterior: 100% condensing Interior: 20% – 95% non-condensing

IQ Switch-PG:

Next up is the Qolsys IQ Switch-PG (SKU: IQSWH-PG). This is an in-wall on/off switch without dimming. It can replace any standard in-wall switch to add automation capabilities to the circuit. With PowerG technology built-in, you will be able to automate devices in areas you may have thought impossible before. Have an outbuilding that you thought was too far away for automation? With PowerG, that goal may be well within reach depending on how far the building is located from the compatible panel.

Before removing the old switch and replacing it with the IQ Switch-PG, be sure the breaker is turned off. Failure to do so may cause damage to the switch and to you! This is a hardwired switch, which will be connected to 120V, so we do recommend that you have a qualified electrician perform the wiring.

Specifications:

• Technology: PowerG
• Power: 120V at 60Hz
• Maximum Load: Incandescent 600W, CFL/LED 300W
• Current: 5A Max
• Standby Power Consumption: <1W
• Wiring: 16 AWG (direct wire connection)
• Noise: 24dB at 20cm Max
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 140°F (-20°C to 60°C)
• Weight: 4.09 oz (116g)
• Operating Humidity: 0% – 85% non-condensing

IQ Dimmer-PG

The Qolsys IQ Dimmer-PG (SKU: IQDMR-PG) is also an in-wall switch, with dimming capabilities included. As with the IQ Switch-PG, this device can replace any existing 120VAC switch that fits within its specifications to add remote control and automation capabilities.

Another attractive feature for this and all of the new hardwired PowerG switches and sockets is that they come with a screwless faceplate. This provides a clean, modern look. Currently, they are only available in white. If you prefer a more traditional look, the screwless faceplate can be removed and there are screw holes for a traditional faceplate. This may also come in handy if you have multiple switches in a line and require a double-gang or triple-gang setup.

Some Important Specifications:

• Compatibility: Compatible with the Qolsys IQ4 NS (PowerG Version), IQ4 Hub (PowerG Version), IQ Panel 4, and IQ Pro panels
• Technology: PowerG
• Power: 120V at 60Hz
• Maximum Load: Incandescent 200W, CFL/LED 100W
• Current: 1.67A Max
• Standby Power Consumption: <1W
• Wiring: 16-10 AWG (terminal block connection)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 140°F (-20°C to 60°C)
• Weight: 4.83 oz (137g)
• Operating Humidity: 0% – 85% non-condensing

IQ Smart Socket-PG:

The Qolsys IQ Smart Socket-PG (SKU: IQSKT-PG) is an in-wall socket with two (2) sockets that can be controlled individually. By replacing a standard in-wall socket with the IQ Smart Socket-PG you gain the ability to individually control the devices plugged into each outlet from the panel's touchscreen, or from the Alarm.com app or webpage.

Using rules and scenes, you can create automation scenarios to turn devices on or off based on other events that occur on the system, or based on a schedule. With the Smart Rules Builder, available on Alarm.com, you can easily create automation rules to suit your every need.

Specifications:

• Color: White
• Tamper Resistant?: Yes
• Technology: PowerG
• Input Power: 120VAC at 60Hz
• Output Load: 120VAC at 60Hz, 15A Total Max Load for both outlets
• Maximum Load: Total 1800W@120V (Resistive Load)
• Standby Power Consumption: <1W
• Dimensions: 14.5 x 2.75 x 1.7 Inches (115 x 70 x 44 mm)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 131°F (-20°C to 55°C)
• Weight: 5.57 oz (157.8g)
• Operating Humidity: 0% – 90% non-condensing

IQ Smart Plug-PG:

The Qolsys IQ Smart Plug-PG (SKU: IQIDP-PG) is an indoor plug-in module. Often referred to as appliance modules, these devices allow you to quickly turn any existing wall outlet into a smart outlet with no electrician required. With its low-profile form factor, you will be able to make one outlet smart without blocking the other outlet in a traditional two-outlet wall plug.

To learn these devices into any of the IQ4 panel lineup, once you have the 4.4.0 firmware installed you'll press the grey bar at the top of the panel screen, go to Settings > Advanced Settings > Enter Installer or Dealer Code (1111 or 2222 by default) > Installation > Devices > Automation > Auto Learn Devices. From there, just power on the PowerG device and it will auto-learn into the system.

Prior to firmware version 4.4.0, the Automation menu option was missing from the Devices screen, so you won't be able to properly learn these devices on older firmware panels. If you attempt to learn any of them as a security sensor, they will likely learn in, but will not operate properly and will need to be removed from sensor programming prior to proper enrollment once the firmware has been updated.

Specifications:

• Color: White
• Technology: PowerG
• Power: 120VAC at 60Hz
• Output Power: 1800W@120V (Resistive Load)
• Standby Power Consumption: <1W
• Dimensions: 2.6 x 1.5 x 1.29 Inches (68 x 38 x 33 mm)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 122°F (-20°C to 50°C)
• Weight: 2.29 oz (65g)
• Operating Humidity: 10% – 90% RH, non-condensing

IQ Outdoor Plug-PG:

The Qolsys IQ Outdoor Plug-PG (SKU: IQODP-PG) allows you to take one single outdoor outlet plug, and make two (2) smart outlets out of it. These two (2) outlets will be enrolled as separate automation devices and can be controlled individually.

Here's an example of how this plug can come in handy. Perhaps you used to have your patio string lights and a bug zapper connected to the two plugs of an outdoor outlet. You can now connect the IQ Outdoor Plug-PG to one of the existing available outlets, and plug the string lights and the bug zapper into it. You can automate the string lights to come on at dusk and turn off at a set time. Automate the bug zapper to turn on based on some other criteria, whether it's a schedule, or based on the opening of the patio door. And you still have one of your previously existing outlets available for another device.

Specifications:

• Color: Black
• Tamper Resistant?: Yes
• Compatibility: Compatible with the Qolsys IQ4 NS (No Screen), IQ4 Hub, IQ Panel 4, and IQ Pro panels
• Technology: PowerG
• Power: 120VAC at 60Hz
• Output Power: 1800W@120V (Resistive Load)
• Output Load: 120VAC at 60Hz, 15A Total Max Load for both outlets
• Standby Power Consumption: <1W
• Dimensions: 2.6 x 1.5 x 1.29 Inches (68 x 38 x 33 mm)
• Operating Temperature: 32°F to 104°F (0°C to 40°C)
• Storage Temperature: -4°F to 122°F (-20°C to 50°C)
• Weight: 2.29 oz (65g)
• Operating Humidity: 10% – 90% RH, non-condensing

At Alarm Grid, we're super excited about the launch of these new automation devices. I believe these will be game-changing, particularly in circumstances where transmitting distance has been a hindrance in the past. I expect we'll see additional PowerG automation devices in the near future.

Hopefully, a PowerG garage door controller, PowerG PGM device, and my personal hope, some PowerG motorized blinds or shades. Stay tuned and we'll let you know when the firmware to support these devices is released. Are you excited about the new PowerG automation products? Leave a comment below and let us know what you think. What other automation devices would you like to see in the PowerG lineup?

Exciting news! Alarm.com has unveiled a new customer app with a fresh look. Faster response times and fewer clicks mean instant access to the data you need. Video and Activity are now conveniently available right from the Dashboard, ensuring quick access to your most vital information.

In addition to the changes and time savings you can see, response times have been improved at the server level as well. Now, instead of clicking the hamburger menu (≡) and then selecting an option, the most commonly used selections, like Video, Activity, and Home, are pinned right at the bottom of the screen.

When you first log in to the app after the update, you'll see a What's New screen that summarizes all the updates.

The Dashboard can be customized so that when you log in, you see exactly what you want, and nothing that you don't. In the example below, Images and Highlights have been removed from the Dashboard. Click and drag the enabled cards to rearrange the order in which they are displayed. To edit the dashboard, click the Home icon, and scroll to the bottom of the screen, then tap Edit Dashboard.

Tapping the Video icon brings you to the video screen where you can see a live view of any camera in your account. You can also see Saved clips, and if you have any cameras enrolled in Onboard Recording you can click the 24/7 option to review selected feeds.

Clicking the gear icon allows you to edit various video settings.

The Activity screen shows you a list of events in chronological order with the newest events at the top. Each day has a Highlights section that provides a brief animated recap of the day's events. Video events provide a thumbnail for quick access to review those items. Use the extensive filter options to find specific items quickly.

Clicking the More option provides you with the options you used to see when clicking the hamburger menu in the upper left.

This upgrade appears to be a significant step forward for Alarm.com. By streamlining the user experience and placing the most pertinent information front and center within the app, overall usability and efficiency are enhanced. As users, we can all appreciate any change that simplifies navigation and reduces the number of clicks needed to access desired features! I am personally excited about this update and how it will make managing our alarms and security systems even more convenient. What are your thoughts on the latest Alarm.com UX update? Feel free to share your opinions and experiences in the comments below. We look forward to hearing from you!

Total Connect 2.0 now offers a server-to-server integration with Genie® and Overhead Door™ garage door openers. This allows you to control your alarm system, automation devices, and garage doors from a single app. No more fumbling between apps to control both your alarm system and garage door.

The new Genie® and Overhead Door™ server-to-server integrations join Chamberlain and LiftMaster as well as several others. Between these server-to-server options and the Z-Wave options for garage door control, you can now operate nearly any garage door from the TC2 app. This makes it much more convenient when attempting to control multiple systems at once, such as when you are arming your system to leave, or disarming your system to return home, and you also need to control the garage door.

This integration doesn't allow for the automation of the garage door, sadly. It provides manual control only, but it is still a worthwhile integration because it simplifies the process of leaving and returning, which most of us do each day, multiple times per day. To set up the integration you simply need a compatible Genie® or Overhead Door™ product, a WIFI connection for that product, and a Total Connect 2.0 account with the Smart Home plan. For Alarm Grid customers, that is a Silver Plan (Self or Full) or higher.

Step-by-Step FAQ for Overhead Door® Integration
Step-by-Step FAQ for Genie Aladdin Connect® Integration

Setting up the integration is easy. Once you log into your Total Connect 2.0 account, click on Devices. Click the three (3) vertical dots in the upper right corner then tap Add/Remove Devices:

From there, choose Genie or Overhead Door™ from the list of available integrations. You will have two (2) options. You can either "Link to Existing Account" or "Add New Account". If you've already been using the garage door opener manufacturer's app, choose the former, if not, choose the latter.

If you choose "Link to Existing Account," you'll be prompted to enter your login credentials for the existing Genie (Aladdin Connect®) or Overhead Door™ (OHD Anywhere®) app, and then click "Login." Once the credentials are verified, you'll see a list of garage doors to select which ones you want to enable.

On the other hand, if you choose "Add New Account," you'll be redirected to the app store to download either Aladdin Connect® or OHD Anywhere®. Follow the provided instructions to set up your garage doors for remote access. Once completed, return to TC2 and follow the steps to complete enrollment. Once again, you'll need to enter the credentials you created for the garage door manufacturer's app and click "Login." Select the garage doors you want to enroll, and you're all set!

We're thrilled to see Resideo adding new third-party integrations to its Total Connect 2.0 offering. While Alarm.com has been more proactive in supporting this type of integration in the past, Resideo is starting to close the gap. We can't wait to see what they offer next!

When the ADC-VDB770 was first released, one of its newest features was a battery with a warmer. This allows the doorbell to work in colder climates without issues. However, users in hot climates have experienced some issues. So, the doorbell will now ship with a battery-less insert instead.

Installations that use a digital chime require a battery, and will not be able to use the battery-free insert. For those customers ordering a new ADC-VDB770 in July 2023 or later, who will be using the doorbell with a digital chime, you must also purchase the ADC-VDBA-770BAT. This is the battery replacement kit for existing ADC-VDB770 units whose battery has reached its end of life, and for new users who will use a digital chime.

If you will be using a mechanical chime, or the wireless chime available from Alarm.com, then you can install the ADC-VDB770 with the included battery-free insert. It charges quickly, which makes for a quick and easy installation. Users in colder climates may also need to purchase the ADC-VDBA-770BAT to prevent issues associated with extremely cold weather.

The purpose of the battery in the ADC-VDB770 is to power the video doorbell for the short period of time that the button is pressed. During a button press, the power circuit of the video doorbell is shorted, which is what causes the doorbell to chime. If not for the battery (or battery-free insert) the doorbell would lose all power during the button press. For a traditional doorbell, this is not a problem. But for a video doorbell, it is.

The battery-free insert, which will now be shipped with the ADC-VDB770 rather than the battery and warmer, is a capacitor that stores a charge. It provides enough power to keep the video doorbell powered while the button is pressed. However, digital chimes require that the button be pressed for a longer period of time, which is why for those chime types the battery is required.

Customers who had overheating issues with the ADC-VDB770 as it was originally sold, with a battery and heater, usually had the doorbell mounted in a location where it got lots of direct sunlight. The battery-free insert is currently not available for individual sale, but this may change in the future. If it does, we'll let you know. For now, if you have an original Alarm.com ADC-VDB770 and the battery is at its end-of-life you will need to replace it with the ADC-VDBA-770BAT.