Product Announcements Posts

Alarm Grid's distributor now has the Qolsys IQ Panel 4 in white available with the 345 MHz receiver in both the AT&T and Verizon versions. The same panel, in black, will soon be available. This panel supports both the legacy 345 MHz 2GIG and Honeywell RF sensors and the DSC PowerG sensors.

If you're looking to upgrade from a panel with either 2GIG or Honeywell 345 MHz sensors, or maybe a combination of both, then you should check out the Qolsys IQ Panel 4, now available, with support for these older wireless sensors. The IQ Panel 4 is an upgrade from the Qolsys IQ Panel 2 with a newer OS, more memory, and a faster processor.

At the center of the Qolsys IQ Panel 4 is a Qualcomm MSM8953 chipset with an 8-core Qualcomm SnapDragon Processor. It has 16 GB of NAND Flash memory. The base operating system is Android 9. By comparison, the IQ Panel 2 and 2 Plus used Android 5.1 as a base, with a quad-core processor. These updates in hardware and software for the IQ Panel 4 mean that it has tons of expansion capability, with the hardware and software to support it. Updated hardware supports updated software as well as new features. Expect lots of updates to this system, much of it based on customer feedback.

There are other updates too. The front-facing camera has been upgraded from 5MP to 8MP. In addition to a higher resolution, the camera also has a wider 120° viewing angle allowing it to capture more context with disarm images and peek-ins. The vertical tilt angle of the camera can be manually adjusted by the user to dial-in the best angle for disarm photos based on the height of panel users.

The Qolsys IQ Panel 4 has support for up to 128 zones, using PowerG and/or Honeywell or 2GIG 345 MHz RF sensors. This makes it the perfect replacement for an older Honeywell or 2GIG system with working sensors still installed. PowerG sensors, manufactured by DSC, are fully encrypted with 128-bit AES encryption and are also supported on every version of the Qolsys IQ Panel 4. They have an open-air range of up to 4,000' (1219m) when used with this panel. And in the unlikely event that you still have a range issue, there are PowerG Repeaters available to boost the range.

The Newest IQ Panel 4 Versions and Kits, now available from Alarm Grid:

Panel Only:

• IQP4003: Qolsys IQ Panel 4 Verizon LTE, Honeywell/2GIG Compatible
• IQP4006: Qolsys IQ Panel 4 AT&T LTE, Honeywell/2GIG Compatible



Unencrypted Kits:

• QOLSYS-IQP4-4003PK-VZ: Qolsys IQ Panel 4 345 Mhz in White Verizon LTE 3-1 Kit
• QOLSYS-IQP4-4006PK-AT: Qolsys IQ Panel 4 345 Mhz in White AT&T LTE 3-1 Kit


• QOLSYS-IQP4-4003PK10-VZ: Qolsys IQ Panel 4 345 Mhz in White Verizon LTE 10-1 Kit
• QOLSYS-IQP4-4006PK10-AT: Qolsys IQ Panel 4 345 Mhz in White AT&T LTE 10-1 Kit



Encrypted Kits:

• QOLSYS-IQP4-4006PGPK-AT: Qolsys IQ Panel 4 345 MHz in White AT&T LTE 3-1 PowerG Kit
• QOLSYS-IQP4-4003PGPK-VZ: Qolsys IQ Panel 4 345 MHz in White Verizon LTE 3-1 PowerG Kit


• QOLSYS-IQP4-4006PGPK10-AT: Qolsys IQ Panel 4 345 MHz in White AT&T LTE 10-1 PowerG Kit
• QOLSYS-IQP4-4003PGPK10-VZ: Qolsys IQ Panel 4 345 MHz in White Verizon LTE 10-1 PowerG Kit

Each of the unencrypted kits listed above includes the Versa-2GIG Door/Window Sensors. In the 3-1 kits, there are three (3) of these, in the 10-1 kits there are ten (10). These kits also include one (1) DSC PG9914 PowerG PIR motion sensor. The encrypted kits listed above contain either three (3) or ten (10) DSC PG9303 PowerG Door/Window Sensors, and one (1) DSC PG9914 PowerG PIR. The 3-1 kits are a great start for installations in apartments and small homes, while the 10-1 kits are great for larger homes and small businesses.

With its 700-Series Z-Wave Plus V2 controller, up to 137 Z-Wave, Z-Wave Plus, and Z-Wave Plus V2 devices can be integrated with the system. This includes Lights, Locks, Thermostats, Water Valves, and Relays. When purchasing new Z-Wave devices, always choose devices with the latest version of Z-Wave supported by the controller whenever possible. Doing so will provide the best possible user experience. Older and newer Z-Wave devices can be installed on the same network, as long as the user is aware of the limitations when such a configuration is used. Up to 242 users are supported on the IQ Panel 4 with one (1) Dealer Code, one (1) Installer Code, and 240 users with the role of Master, User, Guest, or Duress applied to each.

As a quick reminder, the IQ Panel 4 has either a Verizon or AT&T LTE cellular communicator built in. Be sure when purchasing your panel that you choose the carrier that has the best possible signal in the installation area, regardless of what carrier your personal cell phone may use. And when choosing a plan from Alarm Grid to use with your IQ Panel 4, remember that you will need a plan that supports Cellular Alarm Communication. That will be either a Gold or Platinum Plan (Self or Full). If you don't want to take advantage of the Alarm.com app or webpage features, then you can also choose our Cellular Alarm Monitoring plan, which includes Central Station Monitoring, with no remote control capabilities.

The Qolsys IQ Panel 4 is a panel that's truly ready for the future. Qolsys has taken all the feedback they received with their IQ Panel 2, addressed the few inefficiencies and form factor issues, and have really come out with a nearly perfect offering. When coupled with Alarm.com, the Qolsys IQ Panel 4 is a formidable tool in keeping your loved ones and your belongings safe.

Recently Alarm.com announced the release of several new cameras for their Pro Series Video Camera collection. With a dome, bullet, and turret option available, there is sure to be an Alarm.com camera to meet your needs. All offer 1080P resolution, are Indoor/Outdoor, with many more features.

Alarm.com ADC-VC847PF:

The Alarm.com ADC-VC847PF is a 1080P, Indoor/Outdoor Varifocal Dome Camera. A unique feature of nearly all of these new cameras is that they offer a motorized varifocal lens. This feature allows the user to remotely adjust the cameras field of view (FoV) as well as focus, without sacrificing video quality. The VC847PF comes with the option of installing with a white or dark gray (shown above) mounting base. It has an IP66 rating, which means it is waterproof and dust-tight, perfect for use outdoors or in industrial environments.

The ADC-VC847PF supports Power over Ethernet (PoE). This is not a WIFI capable camera, it must have a wired connection to a network. But, with PoE, you can run both network and power through a single Cat5e cable. Some routers and/or switches support PoE, but others do not. If your current networking equipment doesn't support PoE, you can use a PoE injector instead. The power requirement is 12 VDC ± 10% or PoE (IEEE 802.3af), 10 W.

This camera supports 24/7 recording using a compatible Micro SD card (not included, 32GB Minimum Capacity, 512GB Maximum) a Commercial Stream Video Recorder (CSVR126), or both. This is in addition to any clips that are uploaded to Alarm.com cloud storage. It supports HDR (High Dynamic Range), an IR night vision range of ~95' (30m) and many more features. You can see the full specifications in the Data Sheet or by clicking the product link above.

Alarm.com ADC-VC838PF:

The Alarm.com ADC-VC838PF 1080P Indoor/Outdoor Varifocal Turret Camera has many of the same features of the VC847PF, but in a turret style. It too has a motorized varifocal lens which allows remote adjustment of FoV and focus by the end-user. The VC838PF is a PoE camera, using a single Cat5e cable to carry both ethernet and power to the camera. The power requirements are listed as 12VDC ± 10% or PoE (IEEE 802.3af). The IEEE 802.3af standard is an intelligent standard. This means that the devices that use it actually communicate with one another about power. The device receiving power tells the device supplying power how much is required.

The ADC-VC838PF also supports HDR, and has excellent IR night vision, with a range of ~95' (30m). It offers image adjustments of Flip, Brightness, Contrast, Saturation, Sharpness, and Exposure. It also supports 24/7 recording using either a compatible Micro SD card (Minimum Capacity 32GB, Maximum Capacity 512GB), Commercial Stream Video Recorder (CSVR126),or both. This is in addition to uploaded clips to Alarm.com cloud storage. You can read the full specifications in the Data Sheet, or by clicking the product link above.

Alarm.com ADC-VC827P:

The Alarm.com ADC-VC827P is the only one in this group of cameras that doesn't have a motorized varifocal lens. That means there is no remote FoV or focal adjustment capability on this camera. It is a 1080P, Indoor/Outdoor Dome Camera, just like the ADC-VC847PF, and aside from the varifocal lens, their specs are nearly identical. The angle adjustments available on this model are Pan: 0° to 350°; Tilt: 0° to 55°; Rotation: 0° to 180°. The VC827P supports PoE (no WIFI) and the power requirements are listed as 12VDC ± 10% or PoE (IEEE 802.3af), 9.5 W. With its IP66 rating, it is waterproof and dust-tight and like the ADC-VC847PF it comes with a white (shown above) or dark gray mounting base. You can read the full specifications in the Data Sheet, or by clicking the product link above.

Alarm.com ADC-VC728PF:

The Alarm.com ADC-VC728PF is a 1080P Indoor/Outdoor Varifocal Bullet Camera. As you may have gathered by now, when the model number of the camera ends in PF, the camera includes the motorized varifocal lens feature. That is true in this case. Traditionally, bullet cameras have been somewhat unsightly. They often have a metal shroud covering them to protect them from damage. The damage in question could be anything from vandalism to sunlight. They get their name because of their long profile. They are also sometimes called lipstick cameras.

The ADC-VC728PF is an attractive version of a bullet camera. Its dimensions are 6.8" L x 3.0" W x 3.0" H (17.4cm L x 7.5cm W x 7.5cm H). It's almost small enough that it doesn't qualify as a bullet camera. But then, what would you call it? This camera has all the same great features of the rest of the cameras in this list. It has an Ingress Protection rating of IP66, so it's waterproof and dust-tight. The remote varifocal adjustments available are focal length, manual focus adjustment, and autofocus. It supports 24/7 recording via a compatible Micro SD card (32GB Minimum, 512GB Maximum), Alarm.com Commercial Stream Video Recorder (CSVR126) or both. And this is in addition to any clips that are uploaded to the Alarm.com cloud.

This is a PoE camera, so it does not support WIFI, only a wired ethernet connection. It also uses the PoE IEEE 802.3af standard, and the power requirements are 12 VDC ± 10% if using a PoE injector. The VC728PF weighs just 19.1 Oz. (540g). For full specifications, you can read the Data Sheet, or click the product link above.

In addition to the cameras above, we've also added two accessories used for mounting the cameras. These mounting bases act as adapters, adapting the camera's base to fit a standard, third-party mounting base. The ADC-VACC-MNT130 fits the ADC-VC847PF and the ADC-VC838PF. The ADC-VACC-MNT110 fits the ADC-VC827P, ADC-VC728PF, and the ADC-V724 1080P Outdoor WIFI Camera w/2-Way Audio.

What do you think about the new camera offerings from Alarm.com? Their camera hardware, as well as their video service offerings just continue to improve. We think it's very impressive. Drop a comment down below and let us know how you feel about them, or anything else security related you might have a burning desire to discuss. We always look forward to hearing from you!.

Freezing and water damage accounted for 29.4% of Homeowner's Insurance losses by cause in 2019*. From 2015 - 2019, the weighted average cost per accident year was $11,000* for freezing and water damage. Only fire and lightning damage was more costly. But flood damage can often be avoided.

At this time of year, with the worst of winter still ahead of us, our thoughts always turn to incidents of flooding which are caused predominantly by freezing temperatures. In many instances, homeowner's insurance companies want proof that there is both freeze and flood protection in a dwelling as a condition of insurance, or in order to provide the best available rate. With just a few added sensors and tweaks, your existing alarm system can help you prevent freezing and flood damage. Below we'll outline some products and strategies that can help.

To properly protect against this type of damage, it is helpful to know when the temperature in a building drops low enough to cause concern. There are many sensors that can assist in this, and in many cases, a sensor may perform double duty. There are motion detectors that also have built-in freeze sensing, as well as smoke, heat, and combination sensors. Here's a list of just a few, and the systems they are compatible with:

With any of the low-temperature sensing devices above, you can be alerted to dangerously low temperatures within a building. Alerts can come in the form of an email, text, or push notification from either Alarm.com or Total Connect 2.0, a call from the monitoring station, or both. With a Z-Wave or WIFI thermostat you can adjust the temperature when the HVAC system is working, or contact an HVAC service technician when it isn't.

Some of the devices listed in the table above combine freeze and flood sensing into a single unit. Of course, avoiding the presence of water in a location where it shouldn't be is optimal, but in some cases, it may not be possible. Flooding isn't always the result of freezing water pipes. With a flood sensor, you can be alerted to these situations and then take action accordingly. Alarm Grid offers a variety of both wired and wireless flood sensors. Some are listed above. Those and others can be found here.

If you can't control what's happening with the temperature in a location, then the next step in avoiding flood damage is controlling the flow of water. If you have a water shut-off valve within the building, then a Z-Wave water valve is just the thing you need to save the day (and a good deal of money). Once you receive a notification that a freeze condition is possible, or that a flood situation is underway, with Alarm.com or Total Connect 2.0 service, you can either set up a scene to automatically shut off the water within the premises, or you can manually log in and do so remotely.

With a combination of freeze and flood sensors, and a Z-Wave Water Valve, you can anticipate potential low-temperature flooding issues, be alerted to non-freeze-related flooding issues, and either automatically or manually turn off the water before damage occurs. Check with your homeowner's insurance agent to see if there are any discounts available on your policy if you add freeze and/or flood protection with an automated water shut-off option. You may be surprised at how quickly this equipment can pay for itself, even if you never have to use it.

*Statistics are taken from the Insurance Information Institute at iii.org.

**Qolsys Panels come in a variety of versions. All IQ Panel 2 Plus and IQ Panel 4 versions support PowerG wireless sensors. Then in addition, there are versions that support 319.5 MHz wireless, including S-Line Sensors. There are also versions that support 345 MHz wireless and 433 MHz wireless. When purchasing a Qolsys panel, or a sensor that will be used with a Qolsys panel, be sure to match the receiver type with the sensor type. Panels that support 319.5 MHz come in a box with a Gold stripe. Panels that support 345 MHz sensors come in a box with a Silver or Gray stripe, and those that support 433 MHz sensors have a Red stripe on the box.

We told you in 2020 how the Total Connect 2.0 app for Android could support Google Assistant voice commands. This feature allowed you to use your voice to control your system, but only through your phone. Now, the ProSeries panels, including the PROA7PLUS, can fully support Google Assistant.

What this meant back then was that there was nothing to download. Once the feature was enabled on your phone, a blue microphone icon would appear at the bottom of the Total Connect 2.0 app screen. When you pressed it, you could use your voice to check system status, and to arm or disarm the system. Now, with the latest Total Connect 2.0 release, you can actually set up TC2 within Google Home, and control your system from any Google Home capable device you have connected to your account.

Another improvement is the fact that this functionality is now available to both Android and iOS users. On either platform, make sure you have the Google Home app and then follow the steps to configure the Total Connect 2.0 skill within it.

Below is the Google Home App as seen in the Apple App Store:

The ProSeries panels include the Honeywell Home PROA7 and Honeywell Home PROA7PLUS and the Resideo PROA7C and Resideo PROA7PLUSC. Currently, these are the only Total Connect 2.0 compatible panels that support the improved Google integration. If you have one of the ProSeries panels, coupled with a Total Connect 2.0 account and you would like to take advantage of voice commands through Google Assistant, follow these steps:

1. Open the Google Home App, then click the [Plus (+)] Icon at the top left of the main screen.
2. Select, [Set up Device].
3. Select [Works with Google].
4. Search for [Total Connect] then select it.
5. Use your Total Connect 2.0 login credentials to log into TC2 from the skill.
6. Read the User Agreement and if you agree, press [Allow].
7. Be sure the Security System icon is selected, then press [Connect].
8. Click the [Pencil Icon] to assign the system to a room, then choose which room you'd like to add it to.
9. Hit the [Back button] repeatedly until you reach the Home screen.
10. You should now be able to query Google for system status, as well as arm the system to Away, Stay, or Night and Disarm the system using Google Assistant.

Important Update: We now have a full FAQ with a walk-through on how to set up the Google Home feature. This FAQ is applicable whether you're setting Google Home up using an Android or an iOS device running the Google Home App.

Voice control of automation devices is not yet available unless the automation is achieved through a scene tied to system arming or disarming. For example, if you have a scene that turns on the porch light when the system is armed to Away, and you use the Google Assistant to arm in this mode, then the porch light will come on once the system is armed.

Total Connect 2.0 also supports integration with Amazon Alexa, and has for a while now. The configuration is very similar between the two services. One difference between them is that Amazon Alexa is compatible with more different panel types. Most of the Honeywell Wireless All-in-One panels support it. This means that in addition to the ProSeries panels, the Lyric, Lynx, and even the VISTA panels all support being used with Amazon Alexa. As long as the panel is tied to a Total Connect 2.0 account.

To integrate Total Connect 2.0 with Amazon Alexa for voice control of any of the above panels, follow these steps:

1. Open the Alexa App and search for the Total Connect 2.0 skill.
2. Click [Enable]
3. You will be prompted to enter your Total Connect 2.0 login credentials. Enter them, then hit [Login]
4. You will see a User Agreement, read through it, and if you agree click [Allow].
5. Make sure the Security System icon is selected, then click [Connect].
6. A screen should appear showing "Total Connect 2.0 has been successfully linked".

Once the above steps have been completed, log into the Total Connect 2.0 app and go to the Profile Page. Under the Access section, be sure that your user code has been saved and synched with the panel. If this isn't done, Amazon Alexa won't function properly. In the past, we've made FAQs for integrating some different panels with Amazon Alexa. You can find links to those FAQs below:

How Do I Connect My Lyric Alarm System to Alexa?

How Do I Connect My VISTA-21iP to Alexa?

Resideo Official Instruction Sheet on Integration

If you read our blog regularly, you know that certain Qolsys IQ Panel 2 systems that use the AT&T LTE 4G network require an update to the communicator. Without this update, these cellular units will stop communicating after the 3G Sunset. On January 10, these updates will begin automatically.

Qolsys IQ Panel 2 panels that use an AT&T LTE Cellular Communicator will need a firmware update prior to the AT&T 3G sunset, which is scheduled to occur on 02/22/22. Without this update, these panels will lose their connection to the cellular network and could leave the alarm system with no communication path. The update can be performed over WIFI, or by using an SD Card.

For those panels that have a WIFI connection, Alarm.com will begin to automatically push the update on Monday, January 10, 2022. Once these updates begin, they will continue from 8 am - 8 pm seven (7) days per week until all are completed. Some panels will require both a panel firmware update and the cellular communicator update. The Alarm.com server will determine the panels that fall into this category and will perform the updates in the correct order automatically. Once the update has been applied, the panel will reboot as part of the update process. This is normal.

If a WIFI signal is available in the location where the panel is installed, but the panel is not currently connected to it, there are a few different ways to get the panel connected:

1. Locally: The connection can be made at the panel using the touchscreen. Instructions for connecting to WIFI locally can be found here.
2. By the dealer, remotely: Alarm.com dealers, like Alarm Grid, can use the Partner Portal to connect the panel to WIFI. This is found on the Partner Portal website under the Signaling/Broadband Settings.
3. By the end-user, remotely: Starting on 12/13/21, Alarm.com has enabled a tool that allows an end-user to connect the panel to WIFI through the Customer Alarm.com App or Alarm.com Website.

If you would like to go ahead and perform the update on your own, and you need to connect the system to WIFI first, from the customer's Alarm.com app click on Menu > Manage Devices > Select the 3-dots icon next to the panel's name > Select Device Settings > Select Panel WIFI. From there you can either choose an existing camera to copy that device's WIFI settings or select the SSID and complete the authentication process by entering the proper password. Once the connection to WIFI is made, the communication path will be changed from Cell-only to Dual-Path.

Panels that are on version 2.3.0 or lower must be updated to a minimum of 2.3.1 or higher before applying the communicator firmware patch. Panel firmware updates on panels that have a WIFI connection can be performed locally from the panel with a Patch Tag or can be completed remotely by the alarm dealer via Alarm.com's Partner Portal. Once the panel's firmware is on a compatible version (see the link in the paragraph below) the cellular firmware can be installed using the patch tag: ATT3GSunset

For panels that have no WIFI connection available, the Qolsys IQ Panel 2 can be updated locally using a MicroSD Card. The upgrade files, as well as instructions on how to perform the local upgrade, are available on Alarm Grid's Qolsys IQ Panel 2 Plus Firmware Update page. Both the panel firmware files and the ATT3GSunset patch can be downloaded from there.

This issue only affects AT&T LTE Cellular units. Verizon cellular units are in no way affected. This update is required because early Qolsys AT&T units used a provisional VoLTE Firmware Version. This later changed when VoLTE was fully released and because the difference between the two firmware versions didn't affect a panel's ability to send signals via cellular, no action was required at that time. AT&T realized that the upcoming sunset would have a detrimental affect on these early communicators and alerted Qolsys and Alarm.com of the required update.

If you are unsure whether your panel requires the update or not, contact your alarm dealer. They can verify whether or not your panel requires the panel update as well as the cellular update. This version information is only available when checked through the Partner Portal Website, and is not available from the Alarm.com Customer App or Website. You can read the full Qolsys Technical Service Bulletin regarding this upgrade here.

Qolsys IQ Panel 2 equipment that uses an AT&T LTE Cellular Communicator requires a firmware update prior to the AT&T 3G sunset date of 02/22/22. Without this update, these devices will lose their connection to the cellular network. The update can be performed over WIFI, or by using an SD Card

If a WIFI signal is available in the location where the Qolsys IQ Panel 2 is installed, but the panel is not currently connected to it, there are a few different ways to connect:

1. Locally: The connection can be made at the panel using the touchscreen. Instructions for connecting to WIFI locally can be found here.
2. By dealer remotely: Alarm.com dealers, like Alarm Grid, can use the Partner Portal to connect the panel to WIFI. This is found on the Partner Portal website under the Signaling/Broadband Settings.
3. By user remotely: Starting on 12/13/21, Alarm.com is enabling a tool that allows an end-user to connect the panel to WIFI through the Customer Alarm.com App or Alarm.com Website.

In order for the customer to connect their panel to WIFI using the customer app they will click on: Menu > Manage Devices > Select the 3-dots icon next to the panel's name > Select Device Settings > Select Panel WIFI. From there the user can either choose an existing camera to copy that device's WIFI settings, or select the SSID and complete the authentication process. Once the connection to WIFI is made, the communication path will be changed from Cell-only to Dual-Path. This may be useful for panels installed in locations where the building is not always occupied.

Starting on Monday, January 10, 2022 Alarm.com will begin to automatically deploy the firmware update to any WIFI connected panel that has not already received it. The automatic update process will proceed through the queue of needy panels 7 days per week during daytime hours (8am - 8pm panel time). As part of the update, a system reboot will occur.

In some cases, the panel's firmware may require an update before the cellular firmware update can be implemented. Panels that are on version 2.3.0 or lower must update to a minimum of 2.3.1 or higher. Panel firmware updates on panels that have a WIFI connection can also be performed locally from the panel with a Patch Tag, or can be done remotely via Alarm.com's Partner Portal. Once the panel's firmware is on a compatible version (see the link in the paragraph below) the cellular firmware can be installed using the patch tag: ATT3GSunset

For panels that have no WIFI connection available, the Qolsys IQ Panel 2 can be updated locally using a Micro SD Card. The upgrade files, as well as instructions on how to perform the local upgrade are available on Alarm Grid's Qolsys IQ Panel 2 Plus Firmware Update page. Eventually, Qolsys will also make the cellular firmware update patch available for download and install via Micro SD. Once they do, we will also host it on our site. As of 12/10/21, it is not yet available.

This issue only affects AT&T LTE Cellular units. Verizon units are not affected. This issue is occurring because early Qolsys AT&T units used a provisional VoLTE Firmware Version. This later changed when VoLTE was fully released. Since the difference between the provisional firmware and the released version didn't affect a panel's ability to communicate via cellular, no action was required before. If you are unsure whether your panel requires the update or not, contact your alarm dealer. They will be able to verify this information for you, as this information is only available when checked through the Partner Portal Website, and is not available from the Alarm.com Customer App or Website. Read the full Qolsys Technical Service Bulletin here.

Users of the Lyric Alarm System with an LYRICLTE-A AT&T LTE Communicator installed take note. Resideo has identified an issue where, after the AT&T 3G sunset on 02/22/22, any panel not properly updated will lose its connection with the cellular network. This issue does not affect Verizon units.

The firmware version that resolves this issue is 01.09.07772.494, and it is available now on the Resideo AlarmNet360 servers. The issue at play here is that the AT&T cellular communicator currently falls back on the 3G network when it can't connect to LTE. Once an LYRICLTE-A communicator is registered, it looks for both an LTE signal and a 3G one. Without this critical firmware update, these communicators would continue to look for a 3G signal after the 3G sunset. Being unable to find a 3G signal, they will lose connection and go offline.

Users who find themselves in this situation have a few options. If you are a Lyric Alarm System user with the AT&T LTE communicator installed, you can choose to go ahead and manually update your system now. The system needs to be disarmed and have no trouble conditions present in order for the firmware update to go through, so a manual update allows you to choose a time when it is disarmed and ready. It also allows you to confirm that the update was successful after you see your panel reboot.

Since this is a critical update, AlarmNet will begin automatically updating panels that are affected by this issue starting on December 8, 2021. Since a firmware update can only go through when the panel is disarmed with no troubles, any users with a zone trouble, or a low battery message that they have been putting off correcting, should go ahead and take care of the issue. Once all trouble conditions are clear and the system is disarmed, we recommend that you go ahead and manually perform the firmware update. Instructions for updating are linked above.

If your system is automatically updated, it will reboot as part of the update process, so don't be alarmed if you see this happen. Step 3 in the FAQ on updating the panel linked above shows you how to confirm the panel's firmware version. So, if you see your panel reboot you can verify that an update was successfully completed.

Any Lyric Controller with a LYRICLTE-A AT&T LTE Communicator that is being installed on or after 02/22/22 will need to be updated to firmware version 01.09.07772.494 via the built-in WIFI communicator before the LYRICLTE-A will work properly. The firmware update should be completed prior to the installation of the LYRICLTE-A. The LYRICLTE-V Verizon LTE Communicator is not affected by this issue. You can read the full notice from Resideo here.

Local Alarm Mode, also called Demo Mode, is a way for an alarm dealer to demonstrate the full features of the panel without having to register it to an AlarmNet360 account. However, while in this mode, panel communications can't be configured. A panel in this mode can seem to be broken.

Alarm Grid has seen several of the Honeywell Home PROA7, Honeywell Home PROA7PLUS, Resideo PROA7C, and Resideo PROA7PLUSC panels recently that have either arrived with Local Alarm Mode enabled, or have been put into this mode during initial setup. Once Local Alarm Mode has been enabled, it is impossible to configure the panel communication settings until Local Alarm Mode has been toggled off.

Local Alarm Mode is a valuable tool that has been made available to alarm dealers so that they can demo these new panels for a customer in spite of the fact that the panel isn't associated with an account. This was particularly important when the panel was first introduced because there was no local programming. For those early panels, until the ProSeries panel was registered, it couldn't do much unless Local Alarm Mode had been enabled.

This was a great tool at the time for alarm dealers, but for DIY customers, it doesn't offer much in the way of benefits. Now that the panel has local panel programming available, there really is no reason for an Alarm Grid customer to want to use this feature. Whether the panel arrived with this feature enabled, or the feature was enabled during programming, once the customer decides to have the system monitored, whether self monitored, or with central station monitoring, Local Alarm Mode should be disabled.

To check to see if Local Alarm Mode is enabled or disabled, choose the Menu icon (≡) at the bottom center of the Home screen. Select Tools > Installer Code (default is 4112) > Local Alarm Mode. The feature can then be toggled OFF if it is enabled. If it was enabled and you toggle it off, you'll see a confirmation screen, click on the "YES, DISABLE" option.

If you've been using the system with Local Alarm Mode enabled, and you have signed up for alarm monitoring with Alarm Grid, be sure to toggle this feature OFF as soon as possible. Depending on which monitoring plan you sign up for, activation of your account may begin immediately after sign up, and having this feature enabled at that time can cause delays. This is particularly true of the Self-Monitoring options. If you signed up for a central station monitoring plan, just be sure to disable this feature prior to your activation appointment.

Update 12/02/21:

We have confirmed with Resideo and at least one customer that the issues regarding the syncing of Automation between all versions of the Tuxedo Keypads, and the VAM have been resolved and that remote control of Z-Wave devices has returned to normal. Users should now be able to remotely control Z-Wave Automation Devices during any Total Connect 2.0 session. Any Alarm Grid customer that notices issues like this in the future, please report it to support@alarmgrid.com.

Update 11/26/21:

On Tuesday of this week, Resideo announced an update meant to fix this issue. Apparently, it fixed the portion of the issue where all Automation Syncs were failing, but did not address the issue with being unable to control Z-Wave Devices remotely.

There is something of a workaround for this portion of the issue at this time. During the TC2 session where a successful Automation Sync occurs, you can control Z-Wave devices remotely. Once you end that TC2 session and begin another one, you will lose that ability. So, for now, if you need to control a Z-Wave device remotely, perform a sync, and once you see in the Activity Log that the Automation Sync was successful, you will be able to control Z-Wave devices until the current TC2 session ends. Stay tuned and we will provide further updates as this issue is resolved.

Original Post:

In the last couple of weeks, Alarm Grid has noticed several customers with VAM and Tuxedo Keypads (all versions) having trouble syncing Z-Wave devices with Total Connect 2.0. This prevents newly added Z-Wave devices from showing up in TC2, though local control at the device is still available.

This issue doesn't seem to affect Total Connect 2.0 accounts associated with AiO (All-in-One) panels such as the Lyric Controller and the Honeywell Home PROA7PLUS. Accounts with these panel types should be working fine. It is unknown exactly what the problem is, and there is currently no workaround available. We've been in touch with Resideo and Honeywell Home and they are aware of the problem, but there is no Estimated Time of Resolution (ETR) for a fix.

You can continue to add and remove Z-Wave devices locally at the VAM or Tuxedo. But any changes that are made locally at the Z-Wave controller will not be synced to Total Connect 2.0. This means that any device deleted locally will continue to show up in TC2, and any device added locally will not show up in Total Connect 2.0 until this issue is resolved and a successful automation sync occurs.

Any device that currently shows up in Total Connect 2.0, and still exists in the Tuxedo or VAM CANNOT be controlled remotely through TC2. When an attempt to perform an Automation Sync occurs, there is no Automation Sync Failed, or Automation Sync Successful message displayed in TC2 Activity. Status changes from the Z-Wave device to TC2 seem to be coming through fine. It's only the sync process and remote control that seem to be having issues.

Alarm Grid is working with Resideo and Honeywell Home, and as soon as this issue is resolved, we'll post about it here. We posted information earlier this year about the Tuxedo Keypads and VAM Automation Controllers not updating the weather properly. We don't know if this current issue is related to the previous one, but we hope that it will be resolved soon. Stay tuned to our blog for updates.

Alarm.com announced last week that it would begin offering a MicroSD card for use with its cameras that is made by Western Digital. Prior to that time, they offered a card manufactured by Micron. The WD Purple MicroSD card offers a lower price point and higher endurance performance.

The Alarm.com ADC-USD-256GB-WD MicroSD card is designed by Western Digital specifically for the mainstream video market. It offers an excellent balance of price, endurance, capacity, and longevity. This card is being offered by Alarm.com, but it can be used in any video camera that supports the use of a MicroSD card, either for backup, in the event the camera loses its network connection, or for primary recording, such as with the Alarm.com Onboard Recording and Smart View feature.

Alarm.com cameras only support card capacities up to 256GB, which is, I'm sure, why they've chosen to sell only cards with the 256GB capacity. Western Digital actually makes the WD Purple MicroSD cards in capacities from 32 GB to 1TB, as you can see from their Data Sheet. Currently, Alarm Grid is only offering the 256GB capacity cards that are offered through Alarm.com.

The WD Purple MicroSD cards use advanced 96-Layer 3D NAND technology. What this means is that there are 96 layers of NAND Flash memory medium stacked together, forming a 3D shape, sort of like a 96 story skyscraper, but very tiny. There are vertical channels between the layers, allowing communication between them. This architecture allows for less power consumption, greater storage capacity, greater endurance, and the ability to operate in temperatures ranging from -13℉ - +185℉ (-25℃ - +85℃). It also makes them humidity resistant, so they're great for working both indoors and outdoors.

Another feature of these MicroSD cards that makes them perfect for video surveillance use is the Card Health Monitoring feature. With compatible cameras, the camera can send a notification when it's time to replace the card. We're unsure if the Alarm.com cameras support this feature, but we have a request into them to check, and will update this post with the answer.

Update: Per Alarm.com CORE Technical Support, the Alarm.com cameras do not support the Card Health Monitoring feature at this time, but may begin supporting it in the future.

What are you thoughts on this subject? Do you have a camera that supports a higher capacity MicroSD card that you would like to see us offer for sale? Leave a comment below, and if there's interest, we can check into offering these cards in other capacities. Until then, have a great week, and we'll see you soon. Stay safe!