Product Announcements Posts

Users of the Lyric Alarm System with an LYRICLTE-A AT&T LTE Communicator installed take note. Resideo has identified an issue where, after the AT&T 3G sunset on 02/22/22, any panel not properly updated will lose its connection with the cellular network. This issue does not affect Verizon units.

The firmware version that resolves this issue is 01.09.07772.494, and it is available now on the Resideo AlarmNet360 servers. The issue at play here is that the AT&T cellular communicator currently falls back on the 3G network when it can't connect to LTE. Once an LYRICLTE-A communicator is registered, it looks for both an LTE signal and a 3G one. Without this critical firmware update, these communicators would continue to look for a 3G signal after the 3G sunset. Being unable to find a 3G signal, they will lose connection and go offline.

Users who find themselves in this situation have a few options. If you are a Lyric Alarm System user with the AT&T LTE communicator installed, you can choose to go ahead and manually update your system now. The system needs to be disarmed and have no trouble conditions present in order for the firmware update to go through, so a manual update allows you to choose a time when it is disarmed and ready. It also allows you to confirm that the update was successful after you see your panel reboot.

Since this is a critical update, AlarmNet will begin automatically updating panels that are affected by this issue starting on December 8, 2021. Since a firmware update can only go through when the panel is disarmed with no troubles, any users with a zone trouble, or a low battery message that they have been putting off correcting, should go ahead and take care of the issue. Once all trouble conditions are clear and the system is disarmed, we recommend that you go ahead and manually perform the firmware update. Instructions for updating are linked above.

If your system is automatically updated, it will reboot as part of the update process, so don't be alarmed if you see this happen. Step 3 in the FAQ on updating the panel linked above shows you how to confirm the panel's firmware version. So, if you see your panel reboot you can verify that an update was successfully completed.

Any Lyric Controller with a LYRICLTE-A AT&T LTE Communicator that is being installed on or after 02/22/22 will need to be updated to firmware version 01.09.07772.494 via the built-in WIFI communicator before the LYRICLTE-A will work properly. The firmware update should be completed prior to the installation of the LYRICLTE-A. The LYRICLTE-V Verizon LTE Communicator is not affected by this issue. You can read the full notice from Resideo here.

Local Alarm Mode, also called Demo Mode, is a way for an alarm dealer to demonstrate the full features of the panel without having to register it to an AlarmNet360 account. However, while in this mode, panel communications can't be configured. A panel in this mode can seem to be broken.

Alarm Grid has seen several of the Honeywell Home PROA7, Honeywell Home PROA7PLUS, Resideo PROA7C, and Resideo PROA7PLUSC panels recently that have either arrived with Local Alarm Mode enabled, or have been put into this mode during initial setup. Once Local Alarm Mode has been enabled, it is impossible to configure the panel communication settings until Local Alarm Mode has been toggled off.

Local Alarm Mode is a valuable tool that has been made available to alarm dealers so that they can demo these new panels for a customer in spite of the fact that the panel isn't associated with an account. This was particularly important when the panel was first introduced because there was no local programming. For those early panels, until the ProSeries panel was registered, it couldn't do much unless Local Alarm Mode had been enabled.

This was a great tool at the time for alarm dealers, but for DIY customers, it doesn't offer much in the way of benefits. Now that the panel has local panel programming available, there really is no reason for an Alarm Grid customer to want to use this feature. Whether the panel arrived with this feature enabled, or the feature was enabled during programming, once the customer decides to have the system monitored, whether self monitored, or with central station monitoring, Local Alarm Mode should be disabled.

To check to see if Local Alarm Mode is enabled or disabled, choose the Menu icon (≡) at the bottom center of the Home screen. Select Tools > Installer Code (default is 4112) > Local Alarm Mode. The feature can then be toggled OFF if it is enabled. If it was enabled and you toggle it off, you'll see a confirmation screen, click on the "YES, DISABLE" option.

If you've been using the system with Local Alarm Mode enabled, and you have signed up for alarm monitoring with Alarm Grid, be sure to toggle this feature OFF as soon as possible. Depending on which monitoring plan you sign up for, activation of your account may begin immediately after sign up, and having this feature enabled at that time can cause delays. This is particularly true of the Self-Monitoring options. If you signed up for a central station monitoring plan, just be sure to disable this feature prior to your activation appointment.

Update 12/02/21:

We have confirmed with Resideo and at least one customer that the issues regarding the syncing of Automation between all versions of the Tuxedo Keypads, and the VAM have been resolved and that remote control of Z-Wave devices has returned to normal. Users should now be able to remotely control Z-Wave Automation Devices during any Total Connect 2.0 session. Any Alarm Grid customer that notices issues like this in the future, please report it to support@alarmgrid.com.

Update 11/26/21:

On Tuesday of this week, Resideo announced an update meant to fix this issue. Apparently, it fixed the portion of the issue where all Automation Syncs were failing, but did not address the issue with being unable to control Z-Wave Devices remotely.

There is something of a workaround for this portion of the issue at this time. During the TC2 session where a successful Automation Sync occurs, you can control Z-Wave devices remotely. Once you end that TC2 session and begin another one, you will lose that ability. So, for now, if you need to control a Z-Wave device remotely, perform a sync, and once you see in the Activity Log that the Automation Sync was successful, you will be able to control Z-Wave devices until the current TC2 session ends. Stay tuned and we will provide further updates as this issue is resolved.

Original Post:

In the last couple of weeks, Alarm Grid has noticed several customers with VAM and Tuxedo Keypads (all versions) having trouble syncing Z-Wave devices with Total Connect 2.0. This prevents newly added Z-Wave devices from showing up in TC2, though local control at the device is still available.

This issue doesn't seem to affect Total Connect 2.0 accounts associated with AiO (All-in-One) panels such as the Lyric Controller and the Honeywell Home PROA7PLUS. Accounts with these panel types should be working fine. It is unknown exactly what the problem is, and there is currently no workaround available. We've been in touch with Resideo and Honeywell Home and they are aware of the problem, but there is no Estimated Time of Resolution (ETR) for a fix.

You can continue to add and remove Z-Wave devices locally at the VAM or Tuxedo. But any changes that are made locally at the Z-Wave controller will not be synced to Total Connect 2.0. This means that any device deleted locally will continue to show up in TC2, and any device added locally will not show up in Total Connect 2.0 until this issue is resolved and a successful automation sync occurs.

Any device that currently shows up in Total Connect 2.0, and still exists in the Tuxedo or VAM CANNOT be controlled remotely through TC2. When an attempt to perform an Automation Sync occurs, there is no Automation Sync Failed, or Automation Sync Successful message displayed in TC2 Activity. Status changes from the Z-Wave device to TC2 seem to be coming through fine. It's only the sync process and remote control that seem to be having issues.

Alarm Grid is working with Resideo and Honeywell Home, and as soon as this issue is resolved, we'll post about it here. We posted information earlier this year about the Tuxedo Keypads and VAM Automation Controllers not updating the weather properly. We don't know if this current issue is related to the previous one, but we hope that it will be resolved soon. Stay tuned to our blog for updates.

Alarm.com announced last week that it would begin offering a MicroSD card for use with its cameras that is made by Western Digital. Prior to that time, they offered a card manufactured by Micron. The WD Purple MicroSD card offers a lower price point and higher endurance performance.

The Alarm.com ADC-USD-256GB-WD MicroSD card is designed by Western Digital specifically for the mainstream video market. It offers an excellent balance of price, endurance, capacity, and longevity. This card is being offered by Alarm.com, but it can be used in any video camera that supports the use of a MicroSD card, either for backup, in the event the camera loses its network connection, or for primary recording, such as with the Alarm.com Onboard Recording and Smart View feature.

Alarm.com cameras only support card capacities up to 256GB, which is, I'm sure, why they've chosen to sell only cards with the 256GB capacity. Western Digital actually makes the WD Purple MicroSD cards in capacities from 32 GB to 1TB, as you can see from their Data Sheet. Currently, Alarm Grid is only offering the 256GB capacity cards that are offered through Alarm.com.

The WD Purple MicroSD cards use advanced 96-Layer 3D NAND technology. What this means is that there are 96 layers of NAND Flash memory medium stacked together, forming a 3D shape, sort of like a 96 story skyscraper, but very tiny. There are vertical channels between the layers, allowing communication between them. This architecture allows for less power consumption, greater storage capacity, greater endurance, and the ability to operate in temperatures ranging from -13℉ - +185℉ (-25℃ - +85℃). It also makes them humidity resistant, so they're great for working both indoors and outdoors.

Another feature of these MicroSD cards that makes them perfect for video surveillance use is the Card Health Monitoring feature. With compatible cameras, the camera can send a notification when it's time to replace the card. We're unsure if the Alarm.com cameras support this feature, but we have a request into them to check, and will update this post with the answer.

Update: Per Alarm.com CORE Technical Support, the Alarm.com cameras do not support the Card Health Monitoring feature at this time, but may begin supporting it in the future.

What are you thoughts on this subject? Do you have a camera that supports a higher capacity MicroSD card that you would like to see us offer for sale? Leave a comment below, and if there's interest, we can check into offering these cards in other capacities. Until then, have a great week, and we'll see you soon. Stay safe!

Qolsys TSB #211022 indicates that the Qolsys IQ Panel 2 Plus, PowerG and 319.5 MHz version with any communicator has been discontinued. All kits containing these versions have also been discontinued. The IQ Panel 4 PowerG and 319.5 MHz panel is the appropriate replacement in this instance.

Currently Alarm Grid offers the Qolsys IQ Panel 4 Verizon LTE, Interlogix/GE Compatible 319.5 MHz Wireless Alarm Panel w/ PowerG, and the Qolsys IQ Panel 4 AT&T LTE, Interlogix/GE Compatible 319.5 MHz Wireless Alarm Panel w/ PowerG. Both versions will eventually be offered in Black or White color variations, but at this time only the White variation is available.

This announcement is only for the Interlogix/GE compatible panels that support legacy RF in the 319.5 MHz frequency. The other variations of the IQ Panel 2 Plus, those that support 345 MHz Honeywell and 2GIG legacy RF, and 433 MHz DSC legacy RF sensors are still available at this time. This is because production for the IQ Panel 4 versions of these panels has not yet begun.

Per Qolsys, the IQ Panel 4 PowerG and Honeywell/2GIG compatible panels that support 345 MHz legacy RF sensors are beginning production this week. As supply ramps up, the Qolsys IQ Panel 2 Plus that supports this legacy RF frequency will be phased out. We expect this to begin happening in the near future. Production of the IQ Panel 4 for the DSC compatible panels that support 433 MHz legacy RF sensors will begin production in early December, with a similar phase out of those IQ Panel 2 Plus models soon to follow.

As with the IQ Panel 2 Plus, each Qolsys IQ Panel 4 will support PowerG in addition to one (1) legacy RF frequency. In addition to choosing a panel based on the RF frequency to be used, the user will also want to choose the panel with the built-in cellular communicator that will have the best signal strength and quality in the location where the panel will be installed. This can match the carrier for the user's cell phone, but that is not a requirement. When deciding which cellular carrier to choose, base the decision solely on cellular coverage. Billing for the panel's cellular communicator will be included in the monthly monitoring service charges.

The legacy RF frequency built-in to the IQ Panel 4 is intended to make it easy to replace an existing alarm panel from a different manufacturer. By choosing the IQ Panel 4 that supports the wireless frequency for sensors that are already installed in a location, a user can save a lot of money by not having to buy all new sensors. You get the benefit of an all new, feature-rich alarm panel without the expense, not to mention the time and trouble saved, of replacing existing sensors that still work.

Were you thinking of purchasing a Qolsys IQ Panel 2 Plus in the 319.5 MHz "flavor"? If you were, you can purchase the IQ Panel 4 instead. This panel currently has the exact same User Interface (UI) as the IQ Panel 2 Plus, so the user experience will not differ. We expect the IQ Panel 4 to get a facelift in the near future, with the end-user having the choice of whether they want to use the new interface, or stick with the legacy one. The new UI is supposed to be very similar to the Alarm.com layout. If you have any comments, please leave them below. As always, we look forward to hearing from you!

Alarm.com announced on Friday, October 22, 2021 that they plan to discontinue sales of the Concord 4 Dual-Path VoLTE Module and Gateway at the end of October. Interlogix, which is now owned by UTC (United Technologies Corporation) stopped making the Concord 4 panel in late 2019.

There were two (2) VoLTE Dual-Path communicators formerly offered by Alarm.com. The Alarm.com CD-411-US-AT AT&T LTE version, and the Alarm.com CD-421-US-VZ Verizon LTE version. Both of these modules have been on backorder for some time during the global chip shortage, which may have played a part in the decision to discontinue them.

As of now, there is still a Verizon LTE cellular-only communicator available for the Concord 4 panel. The Interlogix GE 600-1053-LTE-VZ connects to the Verizon LTE network for fast and reliable delivery of alarm signals and Alarm.com notifications. With Alarm.com service, the user also has the ability to review status and send alarm system commands remotely using the Alarm.com app or website.

UPDATE 10/26/21! We've discovered that the Interlogix GE 600-1053-LTE-VZ is not available from any of our vendors. We haven't seen an official discontinuation notice, but it seems it may have been. This means that currently, we can't offer any new LTE communicators for the Interlogix/GE Concord 4. For alarm reporting only, the Resideo LTEM-PA or LTEM-PV with the Resideo PRODCM Dialer Capture Module can be used.

The Concord 4 panel is not one that Alarm Grid sells. However, for those users with a Concord 4 in the field that is still working just fine, an updated communicator allows them to continue using a system they're comfortable with, while taking advantage of newly introduced features.

With a subscription to Alarm.com and one of the Verizon LTE communicators, not only can the user view the status of their system, arm and disarm remotely, and receive text, email, or push notifications on alarm events, but they can also add the convenience of Z-Wave functionality to the system. Z-Wave is a communications protocol that allows various devices in your home or business to communicate with the main system to do things such as turn on lights, set the thermostat to a particular temperature based on a Geo-Fence or on the armed status of the panel, and many more options. The Concord 4 panel just needs to be on version 4.0 or higher to support the use of the 600-1053-LTE-VZ communicator.

What do you think about Alarm.com discontinuing these modules? It's only been about a year since they were introduced. Do you think the global chip shortage led to the demise of the Concord 4 Dual-Path communicators? Leave a comment below and we can discuss further. As always, we look forward to hearing from you.

Resideo and Honeywell Home have just released Firmware Version 03.592.107.0 for the PROA7 and PROA7PLUS panels. This update allows the PROTAKEOVER module to support 5800 Series life-safety sensors like the 5808W3, 5800CO, and more. In addition, it offers some other features and improvements.

There are four (4) different panels in the Resideo and Honeywell Home ProSeries lineup. The Honeywell Home PROA7, and Honeywell Home PROA7PLUS, and the Resideo PROA7C and Resideo PROA7PLUSC. The 03.592.107.0 Firmware Version applies to all of them. The differences between the Resideo versions and the Honeywell Home versions are purely cosmetic. You can find details about that in a previous post.

The biggest news in this firmware release is the addition of life-safety support when using the PROTAKEOVER module. For the Honeywell 5800 Series legacy RF sensors, the use of life-safety sensors such as the 5808W3, 5806W3, 5800CO, and others has actually been ETL tested and passed to the UL Residential Fire standard. When taking over a CO detector, be sure to check the expiration date. CO detectors are usually good anywhere from six (6) to ten (10) years. Life-safety sensors from any of the other manufacturers supported by the PROTAKEOVER, including DSC (433 MHz), Bosch (433 MHz), 2GIG (345 MHz), Qolsys, and Interlogix (319.5 MHz), can be used, but they will not meet the ETL listing requirement.

When life-safety devices are used with the PROTAKEOVER the functionality for Loop 2 becomes automatic. For sensors programmed for Fire, Loop 2 automatically becomes the Maintenance (Clean Me) input. For those programmed as Carbon Monoxide, Loop 2 automatically becomes the End-of-Life input. For this reason, if you use a 5817CB or 5817CBXT, for something such as a wired heat detector input, you MUST strap out the loop 2 input, either with a wire jumper or a resistor, depending on which 5817 you're using, and you cannot use that input for a zone on the system.

Although the addition of life-safety support for legacy RF sensors is the big news in this firmware release, it is by no means the only news. This revision adds the ability to enable or disable on-screen panic alarms. It also adds the ability to program scenes via Total Connect 2.0 that pertain to alarm panel arming and disarming events only. Even if the panel itself doesn't have a PROWIFIZW module installed (Smart Home monitoring plan is still required). Prior to this release, if you had no intention of using Z-Wave devices, but you still wanted to program your system to arm or disarm based on a schedule, you couldn't do so unless you installed a Z-Wave controller in the panel.

Below, we'll list all the added or updated features with an explanation of each:

• Zone Response Type Enhancement: The Device Type "Other" now offers the option to enable Chime. The PROSIXC2W now supports 24-Hour panic response types including 24-hour Silent, 24-Hour Audible, 24-Hour Medical, & 24-Hour Auxiliary. All Device and Response Types are now available when enrolling wireless zones using the PROTAKEOVER module.
• LCD Keypad (PROSIXLCDKP) Enhancement: Now, when a Duress Code is entered at the wireless LCD keypad, only the 4-digit code is required. Previously, users would have to enter the 4-digit code + OFF [1].
• Quiet Time Feature Added: The PROWLTOUCH Keypad now participates in Quiet Time (10:00 pm - 8:00 am). This means that non-emergency Trouble conditions, and Low Battery troubles will not sound the keypad during this time, though they will display. Included in this list are Communicator Trouble, System Low Battery, RF Transmitter Low Battery, RF Jam Trouble, AC Loss, and PROWLTOUCH Supervision Trouble. Sensor Tamper, and RF Supervision will sound. At 8:00 am, if the non-emergency trouble condition still exists, it will sound. This feature is automatic. It cannot be disabled, and the times cannot currently be changed, though that may change in future revisions.
• Additional PROWLTOUCH Enhancements: While in backlight timeout, if the keypad reconnects to WIFI for any reason, the keypad will not illuminate. Keypad supervision is now defaulted as "Disabled". If a system has PROWLTOUCH keypad supervision enabled, updating to this version will NOT disable it. The Wireless Touchscreen keypad can now only be enrolled when the main panel is not in program mode. This prevents conflicts with the PROSIXLCD which MUST be added through panel programming. An issue has been corrected where, if the keypad locked up, the battery had to be removed and re-installed in order to reset the keypad. The Indoor MotionViewer (PROINDMV) clips can now be played back on the PROWLTOUCH as well as on the main panel.
• End-user Can Push User Codes to Z-Wave Locks From TC2: Whew, that was a mouthful! Any Total Connect 2.0 Admin user can now create a user code and send it to a Z-Wave lock via either the Mobile App, or the Website. They have the option to both Push the User to the Lock, and allow the Lock Disarm by that User to automatically Disarm the system.
  
  
• Improved TC2 Behavior During a Z-Wave Lock Jam: Previously, when a lock jam condition was displayed, the only option available was to physically go to the lock and toggle the lock position. Total Connect 2.0 now gives you the option to attempt to Lock or Unlock through the app or website.
• Z-Wave Lock User Code Sync Improvement: In the past, setting the panel user code to match the Yale lock user code would cause issues. This is still not recommended, but the behavior should be improved.
• Security Scenes Available in TC2 Without PROWIFIZW: There is no longer a hardware requirement that the panel have the Z-Wave Controller installed in order to create TC2 Scenes pertaining to security panel-only scenes. Currently, the security system scheduling is only available for Partition 1, and a plan that includes automation (Smart Home) is still required.
• Improved Skybell and TC2 Syncing: Some doorbell cameras were having issues syncing with TC2 after the previous firmware update. Those issues should be resolved.
• Improved PROSIX RF Signal Level Indication: The system now refreshes signal level for PROSIX devices immediately upon entering walk-test mode.
• Improved TC2 Camera List Sync: In the past, it was sometimes necessary to Sync the panel twice to get an accurate camera list. This has been improved.
• Partition Master User Enhancements: A Partition Master User can now only see event logs for the partition(s) they are authorized for.
• Language Corrections: Improvements in translations for both French and Spanish.
• Cyber Security Updates: Ongoing Cyber Security maintenance, as well as other bug fixes.

This firmware update can currently only be installed via WIFI. Any account communicating via cellular only will need to be connected to a mobile hotspot or other "WIFI" option before it can be updated. The size of this update is approximately 8MB.

This is a huge update with a lot of feature additions and some user-recommended improvements. Leave a comment below and let us know what you think about the ProSeries panel and the 3.5 update. As always, we look forward to hearing from you!

When it comes to alarm panels behaving as Z-Wave Controllers, it should be easy to determine if a device is compatible or not. However, we've found that in some cases, not all Z-Wave devices are equal. Z-Wave locks by Schlage have been known to have compatibility issues with certain panels.

Alarm Grid has often stated in our documentation that we prefer that our customers use the Yale or Kwikset Z-Wave locks. We've seen issues with Schlage locks over the years and we haven't really gotten satisfactory answers as to why. We've had customers tell us that they've worked with Schlage, and we have worked with Resideo and Honeywell Home. Sometimes they will work, but other times the customer winds up changing to a different lock manufacturer, or just not using the locks with their panel.

When you look at the most current Lyric Z-Wave Compatibility Chart, which is dated 05/19, and is an official document produced by Honeywell Home, it shows that Schlage Z-Wave locks are compatible. This information is based on engineering and quality assurance testing. But testing and daily use are two different things. Engineers can never think up every scenario to test, no matter how hard they may try. So, once a customer attempts to use the products together in their own home or business, some unforeseen factors may arise and cause issues.

We recently had a customer attempting to use a Schlage Z-Wave lock with a Lyric Security System. When the lock is paired with the panel, the batteries drain very quickly, within one to two weeks. When the lock is used as a stand-alone device, the batteries appear to have a normal life. So, we asked Resideo Technical Support for their input. They suggested that the Schlage locks not be used with the Lyric, ProSeries, or Tuxedo products at this time. There is some conflicting information, certain locks may work with the ProSeries panels while others do not, but it may be best to avoid Schlage locks with these panels for now unless you can wait to use the panel and lock together until the issues are resolved.

The Lynx Series panels appear to support the Schlage locks when the L5100-ZWAVE is employed, but certain conditions must be met. The lock and the panel must be within 12 inches of one another during the pairing process, and must remain at this distance for a full two (2) minutes before either is moved. This allows the full pairing process to be completed. Also, the handing process must be completed immediately following pairing. Resideo engineers are working with Schlage to resolve any issues with those panels that have them, and they hope to have a resolution some time soon, possibly in early 2022.

If you have any thoughts about Schlage Z-Wave locks and their use with any of the Resideo or Honeywell Home alarm systems, drop a comment in the area below and lets get a conversation started. We offer feedback directly to all our vendors on behalf of our customers. We're honored to be your voice.

Alarm.com video customers have another great weapon in their defensive arsenal. It's called Perimeter Guard™ and it works like this. Customers with video analytics enabled and using compatible cameras can program those cameras to flash their LEDs and make noise when an intruder is detected.

All that is required in order to enable this feature is an Alarm.com monitoring plan with Video Analytics enabled. Any Alarm Grid customer who subscribes to a monitoring plan that supports video can have this feature enabled. We don't enable Video Analytics by default because we pay more for it, but we don't charge more for it. But if you want to utilize this feature we're happy to enable it for you. Both of our Platinum plans, as well as our stand-alone video plan support this feature.

The list of cameras that can be used with this feature is always growing. Basically, the camera needs to have either a visible LED or a speaker with which to make noise on. Currently, the cameras that support Perimeter Guard™ are (updated 4/23):

• ADC-V724 on firmware version 0.6.1.387+ (supports LED and Audio Alert)
• ADC-V523 on firmware version 0.6.1.387+ (supports LED and Audio Alert)
• ADC-V723 on firmware version 0.6.1.387+ (supports LED only)
• ADC-VC727P all versions (supports LED and Audio Alert)
• ADC-VC827P all versions (supports LED only)
• ADC-VC847PF all versions (supports LED only)
• ADC-VC728PF on firmware version 0.6.3.601+ (supports LED and Audio Alert)
• ADC-VC838PF (supports LED only)
• ADC-VDB770 on firmware version 02199+ (supports LED and Audio Alert)

With Video Analytics enabled and a compatible camera, the only other thing required is to set up a Video Analytics rule for each compatible camera. This is one of those features that you set, then forget. Get the setup correct, and then it'll take care of itself!

To set this feature up through the Alarm.com Customer Website, follow these steps:

1. Log into the website. Go to www.alarm.com/login and using your Alarm.com credentials log in, completing any 2-factor authentication required.
2. Click Video
3. Click Recording Rules
4. Create or Edit Rule. You can either click the pencil icon to add this feature to an existing Video Analytics rule for a compatible camera, or you can Add a new rule. To see how to create a rule using Video Analytics, check out this informative FAQ. Verify that the initial Video Analytics settings are properly configured, then click Next.
5. Choose response. In the Activates section choose the audible and visible response desired:
   
   • Camera LED response. Click to toggle the Camera Status LED to Enabled if you want the LED to respond when activity is detected. There is a Duration drop-down, select how long you want the LED response to last.
   • Camera Audio Alert. This option is only available on cameras using the 2-Way Audio feature. Click the Camera Audio Alert toggle to enable an Audio Alert. There is an Audio Sound dropdown menu. Select the type of sound you want the camera to make.
6. Click Save

To set this feature up through the Alarm.com App, follow these steps:

1. Log into the App. Open the Alarm.com app and using your Alarm.com credentials log in, completing any 2-factor authentication required. Click the Menu icon in the upper left.
2. Tap Video from the available menu. Then tap the Gear icon.
3. Tap Recording Rules
4. Create or Edit Rule. You can either click the pencil icon to add this feature to an existing Video Analytics rule for a compatible camera, or you can Add a new rule. To see how to create a rule using Video Analytics, check out this informative FAQ. Verify that the initial Video Analytics settings are properly configured, then click Next.
5. Choose response. In the Activates section choose the audible and visible response desired:
   
   • Camera LED response. Click to toggle the Camera Status LED to Enabled if you want the LED to respond when activity is detected. There is a Duration drop-down, select how long you want the LED response to last.
   • Camera Audio Alert. This option is only available on cameras using the 2-Way Audio feature. Click the Camera Audio Alert toggle to enable an Audio Alert. There is an Audio Sound dropdown menu. Select the type of sound you want the camera to make.
6. Tap Save

It's that simple! Once you have this configured, using the advanced video analytics available through Alarm.com, the rule will take care of itself. The idea is that the flashing LED and the audible sounder will scare away an intruder before they ever make it to your home. It's a pound of prevention to ward off a ton of regret.

What do you think about this Alarm.com feature? Have you used it and had experience with it? Do you think it's something you'd like to give a try? Leave a comment below and let us know what you think. We love to hear from our readers.

Alarm Grid has obtained an extremely limited supply of the brand new Resideo IPCAM-WOC2 WIFI, outdoor, 1080p camera, compatible with Total Connect 2.0. After the announcement in March, 2021 that the IPCAM-WOC1 was discontinued, Resideo and Honeywell Home were left with no outdoor camera option.

Our blog in March announced that the Honeywell IPCAM-WOC1 would be discontinued. At the time, we didn't know why the camera was being discontinued. There wasn't a lot of information available then about why it was discontinued, or whether there would ever be a replacement. With Alarm.com releasing new variations of their cameras at a fast and furious pace, we were left to wonder what Resideo was thinking.

In July, 2021, we passed on to our readers that either the IPCAM-WOC1 (also sometimes referred to as the Lyric OC1) would make a return, or if not a return, that it would possibly be replaced with something very similar. It came to light that the reason the outdoor camera had been discontinued in the first place was that certain components involved in its production were no longer being produced.

Resideo was unable to source those same components elsewhere, so they are preparing to release the IPCAM-WOC2. This camera is technically not even released yet, so we don't have official documentation, with the exception of a Quick Install Guide, which frankly, contains several errors. For starters, we know for a fact that the image of the camera and its components used in the guide is incorrect. This document, much like the camera itself, will soon be receiving a face lift.

Some of the things that we know are updated in the IPCAM-WOC2, as compared to the IPCAM-WOC1 are: The Bluetooth Antenna is internal on the IPCAM-WOC2. It was external (part of the big wiring bundle) on the IPCAM-WOC1. The WOC2 will support Audio Analytics, with intelligent sound detection. The WOC1 did not support audio. The IPCAM-WOC2 comes with a 16 GB MicroSD card pre-installed, the IPCAM-WOC1 came with a 8 GB card. These are just a few things that we know about, when the full specs are released, we will update our product description with the full gamut of features and specifications.

If you've been waiting to get your hands on an outdoor 1080p camera that's compatible with Total Connect 2.0, now is your chance to pick one up. Given all the supply chain issues revolving around the global chip shortage, this is one of a handful of products that we know is currently in stock. But you had better hurry, because supplies are extremely limited. Once the units we have in stock are gone, we will likely have to wait for the full product release before we can offer any more.