Site Announcements Posts

We missed an opportunity to recap videos last week, but that just means we have more videos to cover this week. Six (6) today, with more to follow. Michael and Jorge share their knowledge of the 2GIG Edge and the Honeywell Home PROA7PLUS. Summer's almost over but wade in, the water's fine.

Honeywell Home PROA7PLUS: Resolve WIFI Connection Issues

In this video, Michael discusses the various reasons why the Honeywell Home PROA7PLUS might not connect to WIFI. Reasons can include range, environmental issues, and even bad equipment. In addition, there is a specific setting to watch out for on Ubiquiti Access Points. Having this setting enabled can prevent your Honeywell Home PROA7PLUS from connecting to WIFI.

2GIG Edge: What To Expect During AC Loss

During an AC Loss condition, the 2GIG Edge will go into power conservation mode. After a few seconds, the touchscreen will go dark and only illuminate when something occurs that needs to be displayed, or when a user touches the touchscreen. Jorge tells and shows users what to expect as normal behavior when an AC Loss condition occurs.

2GIG Edge: Powering Down Properly

Believe it or not, there is a right way to properly power down an alarm system. In this video Jorge will show you how to properly power down a 2GIG Edge alarm panel. Begin by removing the set screws, pulling the panel off its base then unplugging the battery. Next, unplug the transformer, either at the barrel connector on the panel side, or by unplugging the transformer from the wall. If you can't find the transformer, you can power down by turning power off at the breaker.

Qolsys IQ Remote: Behavior On a Partitioned System

In this video Michael shows you how the Qolsys IQ Remote behaves when it is used on a partitioned system. The IQ Remote will only display the status of the partition to which it is assigned. It will only allow the user to control the assigned partition as well, and only a user with a User Code that has been given access to the assigned partition will be able to interact with the system from the IQ Remote.

2GIG GC3e: Installing the XCVR3 GC3

Michael shows users how to install the 2GIG XCVR3-GC3 to the 2GIG GC3e panel. Unlike with the 2GIG GC2 panel, the installation of the 2GIG XCVR3-GC3 does not require that anything be removed from the GC3e panel first. This transceiver module simply adds 900 MHz 2-way communication capability between the GC3e and the 2GIG TS1 as well as the 2GIG Image Sensors.

Honeywell Home PROA7PLUS: Installing PROTAKEOVER

Michael shows users how to set the dial for legacy RF devices, and then properly install the Honeywell Home PROTAKEOVER module into a PROA7PLUS system. This module allows the PROA7PLUS to support one (1) of five (5) legacy RF frequencies. This allows the panel to support previously existing sensors from Honeywell or 2GIG 345 MHz sensors, existing Qolsys and/or Interlogix/GE 319.5 MHz sensors, DSC 433 MHz sensors, or Bosch 433 MHz sensors. This module allows a user to replace an older panel with the newer PROA7PLUS without having to replace all the existing wireless sensors that are still working.

Qolsys released the Qolsys IQ WIFI last week. The IQ WIFI supports dual-band (2.4GHZ and 5GHz) WIFI and can be used as a stand-alone router. It can also be installed in parallel with an existing network. This provides a separate secure WIFI connection for security devices such as cameras.

WIFI is about as common these days as home phones with a traditional copper line (POTS or Plain Old Telephone Service) were from the 1960's through the early 2000's. However, the adoption of WIFI networking has seen some challenges that were not really an issue when using POTS. Namely, the end-user installation and configuration aspect of WIFI networks, as well as issues with getting, and then staying, connected to them. The security industry has embraced WIFI in a big way in recent years, therefore security system users have felt the pain created by these challenges.

For this reason, Qolsys has introduced the Qolsys IQ WIFI. The IQ WIFI is a mesh-capable controller and agent system. Up to eight (8) devices can be supported per network. One IQ WIFI will connect to the modem, router, or switch via a wired ethernet cable. This IQ WIFI will become the controller for the mesh network. Then, up to seven (7) additional IQ WIFI units acting as Agents can be added for a total of eight (8) devices. This allows a user to blanket virtually every nook and cranny of the home or business with a safe and easily configured WIFI connection. If you have a Qolsys IQ Panel 2 or IQ Panel 2 Plus with firmware version 2.6.0 or later, the network can be configured right from the panel's touchscreen. The range between IQ WIFIs is approximately 130 ft. (39.62 m) with a coverage area of approximately 1,500 square feet (139 square meters). Wireless IEEE 802.11 b/g/n 2.4GHz and IEEE 802.11 a/n/ac 5GHz frequencies are supported.

The Qolsys IQ WIFI can be used as a stand-alone router. Each one contains a WAN port, a LAN port, and a barrel connector for power. Each one also has a WPS button. If your ISP provides you with a combination Modem/Router device, connect the WAN port of the IQ WIFI to one of the available ethernet ports on the Modem/Router. From there you can use the IQ WIFI as a wired or WIFI router. For wired devices, connect directly to the LAN port on the IQ WIFI. If you have more than one wired device to connect, connect a multi-port switch to the IQ WIFI LAN port, and then connect your other wired ethernet devices to the switch. As an alternative, connect the WAN port on the IQ WIFI to an existing router or switch, and then using this device as the Controller, build a parallel WIFI mesh network(s) out from there.

Up to seven (7) additional IQ WIFI devices can be added as Agents to create a mesh network that is as strong as you need it to be. This allows you to run a separate WIFI network inside your home or business that is virtually invisible to anyone attempting to hack in from the outside. Another attractive feature of this type of configuration is the ease of replacing the Internet facing hardware. Any time you need to swap out the main modem or router, all you do is swap out the existing hardware, then connect the Qolsys IQ WIFI acting as the Controller to the new piece of equipment. All of the WIFI devices that have been configured to connect through the IQ WIFI will keep their current configuration. There is no need to go around to each WIFI device and enter new credentials. This is particularly welcome when you have WIFI equipment, such as fixed-mount cameras, that may be installed in multiple and difficult to reach locations.

In many cases, security devices can only use the 2.4GHz WIFI band. When the SSID for both 2.4GHz and 5GHz are the same, this can cause issues for those devices that don't support both frequencies. We've seen this in many instances with the Honeywell Lyric. By allowing the user to separate the two bands, achieved by changing the SSID on one or both of them, you can make sure that any device that needs to use only one band or the other can find and then remain connected to the proper WIFI network. It may seem counter-intuitive to think that a Qolsys product could help to stabilize the WIFI connection for a Resideo or Honeywell alarm system, but it is absolutely possible.

When Qolsys first talked about this device, they called it the Qolsys IQ Router. Since then, they have updated the name to Qolsys IQ WIFI and they plan to release a separate device called the Qolsys IQ Router2, or possibly the IQ WIFI6 later in the year. This will be a more robust device supporting both WIFI and potentially another technology such as Z-Wave, Zigbee, or maybe even PowerG. We look forward to hearing about many more new products to come! What do you think of the Qolsys IQ WIFI? Leave a comment below. We'd love to hear from you.

The police department in Sandy Springs, GA is one of several that adhere to a policy of Verified Response when it comes to burglar alarms. They require proof that a crime has occurred before they will respond. Proof can come in one of several forms, which we will be discussing here.

Different police jurisdictions define verified response in different ways with different verification criteria. In some jurisdictions, a second burglar alarm activation on a different zone within the same address occurring within a certain period of time qualifies as verification. For others, there must be audio, video, or onsite verification before the police will respond. In Sandy Springs, GA, the latter type of verification is required. The full Alarm Dispatch Guidelines for Sandy Springs, GA can be found here.

This is not to say that the City of Sandy Springs or any other police department that otherwise requires verification won't respond to any type of alarm without proof of an issue at the site. For most jurisdictions, if there is a Panic, Duress, Hold-up, Medical, CO, Elevator or Fire alarm, the requirement for verification is waived and immediate dispatch can be requested. But, at least in the case of Sandy Springs, if authorities respond and there is no evidence of criminal activity or any other emergency, then false alarm fees will apply.

Furthermore, if a monitoring station employee requests public safety dispatch on an alarm based on audio or video proof that a crime is occurring or has occurred, then Sandy Springs requires that they submit proof of verification within 24 Hours of the dispatch request. Failure to do so will incur additional fines! Proof can either be described to the monitoring station employee by the end-user after checking their cameras or other means of verification, or it can come from the monitoring station employee themselves having reviewed audio or video evidence. The burden of proof has been placed squarely on the monitoring company.

If a customer has an alarm system that uses Audio Alarm Verification, sometimes referred to as 2-Way Voice, then the monitoring station can use this to verify if an unauthorized individual is onsite. In the case of Sandy Springs, silence does not count as proof of an issue, the monitoring station dispatcher must hear footsteps, talking, sounds of rummaging, or other proof of an issue at the site. If the customer has video surveillance, either the customer, or in some cases the monitoring station, can use the video system to verify if an alarm is an actual break-in. The customer may even have a friendly neighbor who is willing to receive a notification from the alarm monitoring company and will go and check things out for them and report back.

However, not every monitoring company will support 2-Way Voice. Currently at Alarm Grid, we don't support this option. And not every customer wants to blanket their property with security cameras. Some properties are too large, or too far away from neighbors to make relying on a neighbor a viable option. In these cases, the best option may be to employ a guard service.

In the past few years, Alarm Grid has partnered with a company called Vet Sec to provide an onsite guard response to monitored locations in jurisdictions such as Sandy Springs. Vet Sec employs guards, in most cases these guards are unarmed or they may be armed with non-lethal weapons (tasers). Once an alarm occurs, the monitoring station will contact Vet Sec, rather than the local police department. A single guard will respond and check the location for signs of a break-in or any other criminal activity, such as vandalism. If evidence of a crime is found, they will notify the monitoring station and wait up to 30 minutes for a key holder and the authorities to arrive. In exchange, they charge a fee for this site visit. The price may vary by location. In most cases, the police should respond within 30 minutes, but if it takes longer for them to arrive, and the customer or other key holder wants the guard to wait with them, then additional fees may apply.

There are several great things about this service. For one, just like with Alarm Grid monitoring, there is no contract so a customer can cancel at any time. Also, this is a "pay as you go" service, so a customer is only billed if a guard actually responds to their monitored location. The fees are billed to Alarm Grid and are then applied to the customer's monthly monitoring fee on the next automatic bill date. Alarm Grid does not markup this fee, we simply pass the fee along to the customer. What we pay, you pay.

Areas in the United States where Verified Response is Required:

Please keep in mind that this list is something that may evolve with little notice. It may be difficult to keep the list 100% accurate, but we will do our best. There have actually been a few places where the police department tried using verified response, and then changed their mind due to increases in property crime. San Jose, CA is one that comes to mind. It was reported in 2019 that they had decided to change their policy and move away from requiring verified response.

You may have noticed that the list above didn't feature any locations from our neighbor to the north. There are a couple of places in Canada that require a version of verified response. Winnipeg, Manitoba, and London and Toronto, Ontario have all adopted a more lax definition of this type of verification. In all three of these locations, the police department will accept two or more activations of two or more separate burglary zones as a form of verification. Currently, Alarm Grid does not offer a guard service in any of the Canadian provinces. If this changes, we'll be sure to update this blog post.

So, of course the burning question is, "How much does it cost?" For most locations the charge is $45 per site visit. There are a few locations where the price differs. In Sandy Springs, GA, the price is $68 per site visit. In Albuquerque, NM customers currently pay $57.07 per visit, and in Eugene, OR the price is $60 per site visit.

What do you think of the Verified Response Policy recently implemented in Sandy Springs, GA? Is it overdue, or overreach? Tell us what you think in the comments below. We'd love to hear from you. Stay tuned to our blog for more exciting security industry news. If you need help figuring out what system you have in the house you just moved into, or you're looking to upgrade an existing system, or to install one for the first time, reach out to us via email at support@alarmgrid.com. We're here Monday - Friday from 9 am to 8 pm Eastern. We look forward to hearing from you!

The year 2020 was about as tough as a well-done $2 steak. I hope never to have another one like it. On the other hand, 2021 is shaping up to end on a high note. One of the high points begins today. After skipping last year, Reed Exhibitions will hold ISC West live this year in Las Vegas.

In years past ISC West, the largest trade show associated with the safety and security industry, has been held in the spring. Due to COVID-19, the 2020 show was postponed in March, then postponed again in April, canceled in June, and ultimately held as a virtual-only event in October. We began 2021 with the show being postponed from the traditional spring dates, to July 19 - 21. There was also a comprehensive list of Health and Safety guidelines that those who will attend in-person are expected to follow. This year's show is being billed as a "hybrid" exhibit, with both in-person booths, and virtual events.

Finally, the time has come for the show to begin. Alarm Grid has opted to participate in the virtual-only portion of the show this year. We've reached out to our most popular vendors, and hope to be presenting exciting information on upcoming new products. So far, what to expect from the virtual show has remained pretty well hidden. Whatever we learn in the next few days about upcoming releases and new products, we will share here on our blog, and on our Youtube channel.

How about you, are you planning to attend ISC West this year? If you aren't going to the show, but wish you were, what burning questions would you ask? Personally, I'd like to get the inside scoop on chip shortages this year, and when we may be able to expect the shortages to ease. Qolsys, 2GIG, and Resideo (Honeywell) have all released new products in the recent past, do they have anything else new up their sleeves? We'll be looking for this information, and whatever we learn, we'll pass it along. Stay tuned!

Qolsys IQ Panel 2 and IQ Panel 2 Plus users will be pleased to learn that a new firmware update is available! Qolsys IQ Panel 2 Firmware Version 2.6.1 can be downloaded via patch tag right now. Alarm Grid recommends that IQ2 and IQ2+ users download the update at their earliest convenience.

Important Note: For those looking for the 2.6.1 Firmware File needed to update the panel using an SD Card, we will make that file available as soon as possible. Qolsys has not yet posted it. However, when the SD Card method is used, the panel will still need a WIFI connection, and active monitoring in order to be sure the panel updates properly. For this reason, unmonitored systems should not attempt this update method unless the user is absolutely sure the "Firmware2" update is not needed on the system. For those who need the "Firmware2" update, it is recommended that the Patchtag method of updating discussed below be used.

Before we get into how to download Firmware Version 2.6.1, we would like to discuss what the new update includes. This isn't a particularly loaded update, but it still includes some new features, plus some important fixes and general system improvements. For those reasons, updating at your earliest convenience is advised.

There is a new Sensor Group for motion sensors, that being Sensor Group (45) - Away/Stay Instant Non-Follower. This is just like Sensor Group (15) - Stay Instant, except that the new Sensor Group (45) will still have the system go into alarm if the sensor is faulted while the system is armed away or armed stay, even if an Entry/Exit Zone is faulted first. With the old Sensor Group (15), the system will not go into alarm if the sensor is faulted after (following) an Entry/Exit Zone. In other words, if you fault a sensor with Sensor Group (45) while the system is in its Entry Delay countdown, an alarm will occur, but if you do the same with Sensor Group (15) when the system is in its Entry Delay countdown, no alarm occurs.

For SD Card upgrades, there will be an auto-push of the "Firmware2" Patch from Alarm.com, assuming that the patch hasn't already been applied. This patch prevents certain IQ2 Panels from automatically rebooting at times. You can see more information about the Firmware2 fix from this prior blog post. The only other new feature release from the 2.6.1 release is that the IQ2 is now compliant with BS-8243 Standards in the United Kingdom.

All other changes for the IQ2 in 2.6.1 are general system improvements. As listed below:

• Fixed an issue regarding SRF Sensors, outlined in TSB 210705. This issue prevented legacy SRF sensors from communicating with the IQ2 properly following an AC power loss condition. More information on the issue can be found here.
• Stability improvements to dual-path communication with Alarm.com.
• Improved push notification of message center messages while on Photo Frame screensaver.
• Improved boot-up after performing a software update.
• Improved doorbell camera streaming and push alerts when the panel is in the lock screen.
• Alarm.com backend now shows username when arming/disarming from PowerG Keypads.
• Corrected issue with an improvement from 2.6.0 so that silent and audible panics triggered from the panel are able to properly report as different CID codes to the central station.
• Corrected issue from 2.6.0 involving daily & weekly communication tests with central station.

With that out of the way, let's explain how to apply the update! Like all of the other recent updates, users on Firmware Version 2.5.0 or 2.5.1 will need to stage upgrade to 2.5.3 first before upgrading to 2.6.1. But if you are on 2.5.3 or higher or on less than 2.5.0, then you can go right to 2.6.1. And as always, your system must be on at least 2.0.1 for any firmware update to be applied.

To get started applying the update, make sure your IQ2 or IQ2+ is plugged in and that its battery is charged. Your system must be connected to WIFI and actively monitored so that Alarm.com can determine if the Firmware2 update is required, and then send it to the panel via WIFI if it is. Begin from the main screen of the system. Press the small grey bar at the top. Pick Settings > Advanced Settings > enter the Installer Code if prompted (default 1111) > Upgrade Software > Patch Tag > enter iqpanel2.6.1 (must be entered exactly as shown) > OK > Upgrade Using Network. The update should then go through. Once it begins, do not touch the panel screen.

Remember, it will usually take about five (5) minutes for the update to be completed. You can then check the Software Version in the About Menu under the Software tab. This is good for confirming that the 2.6.1 Firmware Update went through as intended.

Please leave a comment down below with your thoughts on Qolsys IQ Panel 2 and IQ Panel 2 Plus Firmware Version 2.6.1. Don't hesitate to let us know about your experience with the panel or the firmware update. We want to hear your honest opinion and assist with any issues. Like always, stay tuned to the Alarm Grid Blog for more news and updates coming soon!

Alarm Grid is closing early today Monday, July 5th, at 2pm ET. We will be returning at 9am ET tomorrow, July 6th. If you need to reach us, please contact our support email support@alarmgrid.com. We will do our best to give you a prompt reply as soon as we can upon our return tomorrow.

Remember, if you need to put your system on test mode with our central station partner Criticom Monitoring Services (CMS), you should call our number (888) 818-7728, and choose option [9]. If you are an Alarm Grid monitored customer in Canada, and you need to put your account on test mode with Rapid Response, you should call (800) 932-3822. Again, we will be back tomorrow with our regular business hours.

Update! 2GIG has corrected this issue on the Edge panel with a Firmware Update. You can read all about it here.

We have some rather unfortunate news for anyone hoping to use an image sensor with the 2GIG Edge. 2GIG has informed us that the system's only compatible image sensor, the 2GIG IMAGE3, will only function as a motion sensor when paired with the Edge. 2GIG says that they are working on a fix.

In order to enroll the 2GIG IMAGE3 Image Sensor with the 2GIG Edge in any capacity, a 2GIG XCVR3-GC3 Module must be installed inside the panel. This unit is what makes two-way communication between the 2GIG Edge and the IMAGE3 possible. Contrary to popular belief, installing the 2GIG XCVR3-GC3 inside the 2GIG Edge will not have any impact on the system's ability to support encrypted 2GIG eSeries Sensors.

However, even after you install the 2GIG XCVR3-GC3 and enroll the 2GIG IMAGE3, you will find that the IMAGE3 does not work as an image sensor as intended. Instead, the IMAGE3 will only behave as a standard motion detection sensor, and it will not transmit any captured photographs to Alarm.com. This effectively defeats the main purpose of the device, and you would really be no better off pairing an ordinary motion sensor with the Edge.

When we reached out to 2GIG for more information, we were informed that this behavior is not intentional, and a fix is being implemented to make the 2GIG IMAGE3 operate as a true image sensor when paired with the Edge. While it is believed that the fix will be applied as a firmware update for the 2GIG Edge, this is mere speculation, and it has not been confirmed. We also do not have an expected timeframe for when such a fix will be implemented.

Alarm Grid apologizes to anyone who was hoping to use image sensors with the 2GIG Edge at this time. We are just as hopeful as you are that 2GIG will make a quick fix to the problem so that image sensors may be successfully used with the system as intended. Stay tuned to the Alarm Grid Blog for updates on when the issue is corrected. Also please leave any thoughts you have on the situation down in a comment below. We'll be back with more security updates and news coming real soon!

After much waiting and anticipation, Resideo has delivered the firmware update we have all been wanting for ProSeries Panels. ProSeries System Update Version 3.591.92.0 for PROA7PLUS, PROA7PLUSC, PROA7, and PROA7C introduces local programming mode, as well as other system enhancements.

First, we want to cover how to receive the update. Only monitored ProSeries Systems can be updated. You must have your ProSeries System online and connected with the AlarmNet servers in order for the over-the-air (OTA) update to go through successfully. The system must be connected with a WIFI network, as the update cannot be sent across cellular. Remember that while the PROA7PLUS and PROA7PLUSC both come with integrated WIFI network cards, the PROA7 and PROA7C can only connect to WIFI if a PROWIFIZW or PROWIFI has been added separately.

As a one-time event Alarm Grid is planning to send down the new firmware update to all its monitored customers with ProSeries Panels sometime in the coming days. This OTA update is being done in one mass shot to try to update as many users as possible all at once. No special action should be required on your part. Just have your ProSeries Panel powered on and connected to WIFI. While this process isn't perfect, and there will inevitably be some users who miss out on the update for one reason or another, this is the best way for us to ensure that as many end-users as possible have their panels updated. Remember, we can only update ProSeries Systems that are actively monitored by Alarm Grid. If you have a different monitoring provider, then ask them to help you update your system.

If your automatic OTA update fails for whatever reason, or if you didn't have your panel ready at the time of the mass OTA update, then you can request that the update be sent down manually. Alarm Grid customers can email support@alarmgrid.com to request a manual OTA update. Please make sure that you have your ProSeries Panel powered on and connected to WIFI when we push down the OTA update, or else the update process will fail. Our support hours run from 9 am to 8 pm ET M-F, so keep that in mind when contacting us. Furthermore, we cannot push down a manual OTA update to your panel if you receive alarm monitoring service from a different provider. If you are monitored by a different company, then you should instead reach out to your provider for further assistance.

There are some big highlights here in ProSeries Firmware Update 3.591.92.0. Obviously, the elephant in the room is the introduction of local programming mode. Previously, users were forced to have all system programming completed remotely by their monitoring provider. This included basic system setup tasks like enrolling sensors and configuring zone settings. Not only will the introduction of local programming make activations easier for professional technicians, but it will also empower end-users and give them greater control over their systems. This is a huge deal, as it officially makes the ProSeries Panels DIY-friendly alarm systems.

There are other major introductions in ProSeries Firmware Update 3.591.92.0, though they are likely to be overshadowed by the introduction of local programming. Nonetheless, we are still very excited about these smaller, but still important, introductions. For one, there is a boost to system partitioning, as a common lobby partition option is now available. You can set Partition 3 or Partition 4 as the common lobby, depending on how many partitions are being used. The highest number partition will always be the common lobby, and you must have at least 3 partitions in order to enable the common lobby feature.

There are some principles to keep in mind regarding the lobby function. You cannot set both Partition 3 and Partition 4 as the common lobby. Only one can be the common lobby partition at any given time. The way that the common lobby partition works is that disarming any other partition will also disarm the common lobby partition. Additionally, if ALL other partitions are armed, then the common lobby will also automatically arm. The only way you can arm/disarm the common lobby partition independently is if all the other system partitions are in an armed state. All system users have authority over the common lobby partition. Finally, any 24-hour zones assigned to the common lobby partition will sound on keypads of all partitions, but you can only silence alarms and troubles from these zones using the common partition keypad. Any faulted zone in the common lobby partition will be automatically bypassed when the common lobby partition is armed, even if it is armed automatically due to all other partitions being armed.

The ProSeries Firmware Update 3.591.92.0 brings support for some upcoming PROSiX Sensors that we hope to have available on our site very soon. Specifically, we are talking about support for the PROSiX Wireless Repeater (PROSIXRPTR) and support for the PROSiX Wireless Heat (PROSIXHEAT).

A local alarm mode is now supported, meaning you can trigger a localized system alarm, complete with siren, but without the system reporting out. This can be good for scaring away on-site intruders, while also resting easy in knowing that the authorities will not be sent to the premises. This is basically how the system behaves if an intrusion alarm occurs on a system that is not being monitored. When local alarm mode is enabled, all communication to AlarmNet is halted, including access to Total Connect 2.0 features.

The panel will now provide severe weather alerts. This feature requires that the system is set up with Total Connect 2.0 and the corresponding weather package. Remember, this is only possible if the system is monitored and set up with Total Connect 2.0. Ask your monitoring company about receiving weather alerts on the panel.

If you are using the system in Canada, you can now use the PROTLE-CN Communicator. This communicator may be carried by Alarm Grid in the future. Alarm Grid is not provided with the option to sell the Resideo and Honeywell Home lineup of Canadian communicators, however, we can get potential customers in touch with a Canadian distributor. Once you obtain a PROLTE-CN elsewhere, then we will be able to set it up for monitoring.

On the PROA7PLUS and PROA7PLUSC only, you can now stream the live video feed for Total Connect 2.0 IP Cameras and SkyBell Video Doorbell Cameras from both the Panel, as well as any PROWLTOUCH or PROWLTOUCHC Keypad. The PROA7PLUS and PROA7PLUSC also now both support disarm photos from the PROWLTOUCH and PROWLTOUCHC Keypads. Again, these two (2) features are for use with the PROA7PLUS and PROA7PLUSC only.

For all ProSeries Panels, there is backlight timeout improvement. You can now set the backlight timeout for a ProSeries Panel or a PROWLTOUCH/PROWLTOUCHC Keypad to Disable and have the screen go completely dark. This is instead of going to the "inactivity screen" that shows the weather, time & date, 1st thermostat temperature, partition arming status, panic icons, and CELL/WIFI/AC/BLE status.

Other updates include:

• You can now have Partition 1 Disarm automatically when a Z-Wave Door Lock is UNLOCKED.
• There are improvements to the 7-Day Z-Wave Thermostat Schedule on Total Connect 2.0.
• There is now optional device supervision for PROWLTOUCH & PROWLTOUCHC Keypads.
• The PROSIX Wireless Technology is now more accurate in displaying signal strength and remaining battery life.
• There is now improvement in enrollment range for PROSIXSMOKEV and PROSIXHEATV.
• There is now improved multi-language display on the PROSIXLCDKP Keypads.
• If you use a cellular communicator in Canada then you may notice Cellular Roaming Improvement.
• Updates to the ProSeries Cyber Security.
• The PROINDMV Indoor Motion Viewer and Z-Wave Devices are now supported during the AlarmNet360 Panel Replacement Process. This is only for the PROA7PLUS and PROA7PLUSC.

Are you excited about this new update? What do you think about local programming finally being available for the ProSeries Panels. Is there some other new feature that you're also really eager to check out. Let us know in a comment down below. And stay tuned to the Alarm Grid Blog for more news and updates coming soon.

We have a short but sweet announcement to make today, as we now have the DSC PowerSeries NEO ICON Keypads available. These are the equivalent of Fixed English Keypads for the DSC PowerSeries NEO. They are great if you need additional keypads to accompany one or more Alphanumeric Keypads.

The following four (4) DSC ICON Keypads are now available for DSC PowerSeries NEO owners:

• DSC HS2ICN - Wired FE Keypad
• DSC HS2ICNP Wired FE Keypad w/ Proximity Tag Support
• DSC HS2ICNRF9 Wired FE Keypad w/ PowerG Support
• DSC HS2ICNRFP9 Wired FE Keypad w/ Proximity Tag & PowerG Support

The main thing to keep in mind with these ICON Keypads is that they are essentially Fixed English Keypads. This means that they do not display system status, and instead just display the current time. More importantly, they also cannot be used to program the panel, because they will not display zone settings.

In other words, you should only use one of these keypads as an extra keypad controller to accompany an existing Alphanumeric Keypad. You can use the Alpha Keypad a the primary controller and for making system changes. Then the new ICON Keypad can go in a secondary location, such as by your back door or in your master bedroom.

If you are looking for just one Alphanumeric Keypad, then a good option is the DSC HS2LCDRF9 N, as that keypad includes the built-in PowerG Transceiver so that you can begin adding wireless sensors. If you already have a standalone PowerG Transceiver, then you can get the Alpha Keypad without the built-in PowerG Transceiver, the DSC HS2LCD N Keypad or the DSC HS2LCDP N Keypad With Proximity Tag Support. Remember that we sell Proximity Tags for the DSC PowerSeries NEO here in a packs of eight (8).

What do you think of the DSC PowerSeries ICON Fixed English Keypads? Do you think you will add one to your DSC PowerSeries NEO Security System? Let us know in a comment down below. We would love to hear your thoughts. And stay tuned to the Alarm Grid Blog for more security news and product announcements coming soon!

If you use an Interlogix Alarm System with Alarm.com, then you can expect a firmware update for your system's LTE communicator. The firmware update will be automatic, and no action will need to be taken. Interlogix Simon Panels, NetworX Panels, and Concord4 Panels will receive the update.

If you haven't upgraded to an LTE communicator yet, then make sure to do so as soon as possible. The 3G Sunset is going to occur on January 31st, 2022 for AT&T and December 31st for Verizon. If you are not aware of the 3G sunset, then please read this blog to get acquainted. This upgrade is very important to ensure that you do not experience a loss of service.

We want to mention that each firmware update is just a general update designed to improve the user experience. Each update is being pushed down automatically, at no cost to the user. No action is needed on your end, just have your system online and connected with the Alarm.com servers, and everything will be taken care of.

Please note the update according to your Interlogix System:

• Interlogix Concord4 - Firmware Update 189d
• Interlogix NetworX - Firmware Update 189a
• Interlogix Simon XT, XTi, XTi-5, XTi-5i - Firmware Update 191f

Additionally, if you use a Honeywell VISTA System with an Alarm.com SEM (not AlarmNet or Total Connect 2.0), then you will also be getting a pair of automatic system updates. All VISTA Systems using Alarm.com SEMs will receive the SEM VISTA 187i Upgrade and the 1.61 Firmware Upgrade. Again, both updates are automatic, and they are being provided at zero cost.

That's all the news for now. If you have any of the aforementioned systems on Alarm.com, then you can expect the automatic firmware update. If you are monitored by Alarm Grid and you are having any trouble with your system, please email support@alarmgrid.com. Please keep in mind our usual business hours of 9am to 8pm ET M-F.